Social Feed

P
Last reply · posted in Cable Television and Fiber Providers
i ordered dishnetwork, but they were unable to do the install. the installer said that there was no way to get a signal from where my townhouse is positioned. trees are in the way on the back deck and the building is blocking the line of sight for the front deck :(. and that's the only two locations the condo assoc. will allow for dish installs. :down

would another satellite company (directTV, etc..) have any better luck getting signal? or do all the satellite co. generally point in the same direction?

i had adelphia hook up my cable (classic...digital not available) today and its just disgusting. the pq is so poor, i can't even imagine how they can get away with it. when the installer was hooking it up, he asked if i had any idea how bad the cable reception was for the condo. i told him i've heard it wasn't great...but i wasn't expecting what i saw. i would probably get a better pq putting a set of bunny ears on top of my tv :mad:.
8 Replies · 2276 views
mike123abc
You might look at VOOM the satellite is quite a bit east compared to Dish(DIRECTV is east of Dish (18 degrees) but VOOM is way east (57.5 degrees)).

Perhaps if you can see to the SE you can get VOOM.
B
phreak said:
and that's the only two locations the condo assoc. will allow for dish installs.

The condo assoc. may not have anything to say about it. Remember under federal law, you can put a dish anywhere that's under your ownership, or exclusive control. if they don't like it, tough. Worst case, if they try to cause trouble, you can petition the FCC to issue a Declaratory Ruling against them.

Now if a location in question is Common Area, then they do have something to say about it.

All the nitty-gritty details, and the links to the actual Federal Code, are at http://www.fcc.gov/mb/facts/otard.html
S
MOst the time, the office personel from the condo is not live there, so they don't give a damn what your cable picture quality is. They hate you has the dish set up but their own home may has few dishes up. ho ho ho
cdru
BarryO said:
The condo assoc. may not have anything to say about it. Remember under federal law, you can put a dish anywhere that's under your ownership, or exclusive control. if they don't like it, tough. Worst case, if they try to cause trouble, you can petition the FCC to issue a Declaratory Ruling against them.

Now if a location in question is Common Area, then they do have something to say about it.

All the nitty-gritty details, and the links to the actual Federal Code, are at http://www.fcc.gov/mb/facts/otard.html
Looking at the guidelines above several posts, I don't see anything that is glaring obvious as being against the FCC's guidelines. Actually it's quite well worded probably by someone who understood the FCC's guidelines and much more liberal then I think a lot of HOA type guidelines are. The part about breaking the plane and the required 7-day notification requirement may be a little questionable, but other they that, it seems to be in order.

A condo, being much like an apartment, has limited exclusively controlled areas. Usually a front or back porch/deck is it. Assuming this place doesn't have a front porch, the rear deck may be it. Yeah there is always the through-the-window option but I personally thing that route is dumb and only is for people who are desperate (read:college students).

The one other route that may be an option is to see if a foam mock landscaping stone cover would be an option. Not likely though.
B
Homeowners wishing to install a satellite dish must first request permission, in writing, to the Board of Directors prior to installing a dish. The request must include dish diameter and location on the deck, along with a simple wiring diagram. The Board of Directors requires notification at least seven (7) days prior to installing the dish.

If you read the case law, this is clearly illegal. Landlords or HOA's are not allowed to require prior-notification, nor a permit. The FCC has ruled that this unduly delays and impedes a persons ability to recieve DBS signals.

So is the part about "no towers". If they're 12 ft. or less, a "tower" is perfectly OK.
BlackHitachi
Supporting Founder
Last reply · posted in Movie Talk
Since the Reds have there thread we should too!

Last watched Nine inch Nails
Next 3:10 to Yuma
5396 Replies · 511752 views
dfergie

Last of the Dogmen is my favorite of hers.
  • Like
Reactions: osu1991
"MysteryMan"
Gone.webp
osu1991
Star Wars Despecialized Edition

IMG_0803.webp
comfortably_numb
Pub Member / Supporter
Last reply · posted in Internet Television (IPTV) Discussion Forum
Not sure saving $24/year is worth it unless you're a hardcore Philo user. I'll stick with monthly.

IMG_0351.webp
7 Replies · 224 views
Jimbo
Not sure saving $24/year is worth it unless you're a hardcore Philo user. I'll stick with monthly.

View attachment 195247
$24 for the Year, would be more useful.
Howard Simmons
$24 for the Year, would be more useful.
But when you cancel you still have to watch until the plan runs out. With monthly you're done at the end of the month.
Jimbo
But when you cancel you still have to watch until the plan runs out. With monthly you're done at the end of the month.
Sorry, my point was the expense.
comfortably_numb
$24 for the Year, would be more useful.

Philo's monthly price is reasonable, IMO, because it's still the cheapest way I'm aware of to get all the linear Discovery networks AND access to the Discovery Go apps.
  • Like
Reactions: Howard Simmons
Jimbo
Philo's monthly price is reasonable, IMO, because it's still the cheapest way I'm aware of to get all the linear Discovery networks AND access to the Discovery Go apps.
I guess if it was something I used on a regular basis, I suppose.
  • Like
Reactions: Howard Simmons
comfortably_numb
In other Philo news..

IMG_0364.webp
Bobby
Oh boy, I can't wait! 😂
  • Haha
Reactions: comfortably_numb
K
Pub Member / Supporter Lifetime Supporter
Last reply · posted in TV Shows
'Rockford Files' Reboot Gets NBC Pilot Order

I grow tired of all the reboots. Most I don't bother with but will depend on the actor chosen.
19 Replies · 748 views
long_time_Dish
Yeah, I'll check it out as well, but shan't be holding my breath...It'll be tough to equal James Garner in that role...
  • Like
Reactions: Foxbat
harshness
...It'll be tough to equal James Garner in that role...
I can think of a few actors (including some females) who might fit the bill.

This will all depend on the storyline. I'm not sure how well it will translate. Modern TV hasn't been all that kind to PIs and even less kind to CIs (confidential informants).
K
Premier is Saturday, Jan 2nd. Moving to Thursday on the 7th.
long_time_Dish

I wonder how they're/if they're going to do something like the answering machine message opening? It was always funny...
  • Like
Reactions: dfergie
meStevo
Lifetime Supporter
Last reply · posted in The Chit Chat Club
Continuing the Kilauea thread in the Pub here. Perhaps the Iceland one too next time there's remarkable activity.

Currently there is precursory lava flowing into the crater, leading to the next episode that'll probably start within the next day.

You can see the pace of inflation / deflation here. It serves as the primary predictor for when the expect the eruptions, which coincide w/ inflation turning into significant deflation and last for several hours on average with significant fountaining.



View: https://youtu.be/Uecu2seh4b4


Wife and I like the AfarTV feeds, for the discussion along w/ them, though they're otherwise just mirrors of the official USGS feeds.


View: https://youtu.be/iws3rh5vLAQ
123 Replies · 3690 views
  • Like
Reactions: osu1991
Foxbat
Kīlauea seems to be returning to the "normal" eruption script, impressive fountaining from the North Vent. For once, the V2 Cam has the best overall shot:
IMG_1535.webp
The lava flows have covered a good portion of the Halemaʻumaʻu crater floor.
Foxbat
Looks like Episode 55 is over at 09:00 HST, just under six hours. The USGS said the fountains reached 720' or 220 meters.
​
  • Like
Reactions: RaiderPower
Foxbat
The USGS Kīlaeua Webcam #1 has been showing overflows and doming from the North vent overnight. Maybe the volcanic plumbing has settled back into its two-three week cycle of fountaining?

But I do miss the little cinder cone that broke up in the last episode.
Foxbat
Sorry, I should have posted these earlier:

​

We're still waiting on the start of Episode 56.
  • Like
Reactions: RaiderPower
Foxbat
At 08:01 HST 11/05/2026, the North Vent produced what I would call a "wet burp" after the precursory "pistoning" events, small amounts of lava pouring out of the vent for a few seconds to minutes and then everything recedes. There must have been a gas bubble holding thing back because two minutes later the lava started flowing out of the vent in all directions. Then, at 08:25, it stopped. What a tease! I thought this was how Episode 56 started.

About 12 minutes later at 08:38, the North vent once again started overflowing and picked up steam at 08:42. By 09:00, slight doming could be seen in the pool of lava in the vent. Surely this is it!

But, 09:50 and things wind down again. By 09:57 HST there's just fumes coming out of the vent. Phooey.

But then 10:00 comes and the heavy lava flows kick in again. This time seems like the real deal. At 10:30 HST there's little spurts of lava flying up in the air over the vent, but more from gas than a steady fountain of lava. This looks promising!

11:30 HST and the color of the lava is definitely hotter, and the intensity has picked up to a definite dome and precursor to fountaining. The USGS calls Episode 56 as officially starting at 12:10 HST:

Alert Level: WATCH, Color Code: ORANGE 2026-11-05 22:29:12 UTC
HVO/USGS Volcanic Activity Notice

Volcano: Kilauea (VNUM #332010)

Current Volcano Alert Level: WATCH
Current Aviation Color Code: ORANGE

Issued: Thursday, November 5, 2026, 12:29 PM HST
Source: Hawaiian Volcano Observatory
Notice Number: 2026/H514
Location: N 19 deg 25 min W 155 deg 17 min
Elevation: 4091 ft (1247 m)
Area: Hawaii

Summary: Episode 56 of the ongoing Halemaʻumaʻu eruption began at 12:10 PM HST on November 5, 2026.

Volcanic Activity:
Episode 56 of lava fountaining in Halemaʻumaʻu began at the summit of Kīlauea began at 12:10 PM HST on November 5, 2026.

Lava fountain heights are relatively low at about 100 ft (30 meters), but will likely increase. Ground-level sensors near the eruptive vents indicate that winds are blowing from the northeast direction, which suggests that volcanic gas emissions and volcanic material may be distributed to the southwest direction from Halemaʻumaʻu.
  • Like
Reactions: meStevo
osu1991
Pub Member / Supporter
· posted in Movie Talk
0 Replies · 18 views
osu1991
Pub Member / Supporter
· posted in Movie Talk
0 Replies · 24 views
M
Last reply · posted in DISH Network Support Forum
I have Dish with Hopper3. I choose to get local channels OTA and had a "guide list" established at my previous home. Having moved a few miles away, I wanted to update the list by appending a couple new stations via a rescan. As many would know, some stations come in with the UHF/VHF antenna aimed in one direction, while others come in better with a different direction.

Unfortunately, when a scan is done (bringing in 25-30 stations for that particular antenna aim), the dialog screen does not present the established guide list; it presents an empty field to the right that the scanned stations may be selected one by one and added to the empty guide. But because of antenna aim, some stations originally saved are missing, and would have to be retrieved with a different antenna aim. But as I explain, if a 2nd​ scan is done with a different antenna aim, the stations saved from the first scan are lost.

It troubles me that Dish didn't develop software that would allow a user to simply append only 1 or 2 channels to the established list. :mad:

Any thought on this? Has anyone experienced this or heard of this from others?
15 Replies · 509 views
dishstaller
I could very well be wrong....it has been a LOT of years but back when I had a 722K it seemed like when you went back to the scan screen that you could just scan again and it would ADD those channels to the previous list or you could delete the previous results and only add the channels from the new scan.
  • Like
Reactions: charlesrshell
N
I could very well be wrong....it has been a LOT of years but back when I had a 722K it seemed like when you went back to the scan screen that you could just scan again and it would ADD those channels to the previous list or you could delete the previous results and only add the channels from the new scan.
I am not sure about that but I do know that you could manually add additional channels just by entering the actual RF channel number and the older receivers would add the virtual channels to your list
dishstaller
I am not sure about that but I do know that you could manually add additional channels just by entering the actual RF channel number and the older receivers would add the virtual channels to your list
Like I said.....that has been many years ago. Swapped my 722K for a Hopper in 2012.

It does seem like I remember having to delete the existing channels when we did a rescan. Back then our local stations KEPT monkeying around with things and it was non-stop complaints from customers about their channels not coming in. Got so bad that I stopped selling OR installing OTAs....something I had been doing since 1984 so you know it HAD to be pretty bad.
M
You made one of my points for me with this comment, Dishstaller:

"... local stations KEPT monkeying around with things and it was non-stop complaints from customers about their channels not coming in ..."
dennispap
I could very well be wrong....it has been a LOT of years but back when I had a 722K it seemed like when you went back to the scan screen that you could just scan again and it would ADD those channels to the previous list or you could delete the previous results and only add the channels from the new scan.
I remember that also on my 722.
dishstaller
I remember that also on my 722.
Thanks.....has been too many years to remember clearly.
  • Like
Reactions: charlesrshell
Bobby
Keep in mind that the 722 had a built in OTA tuner and the 722K had a plug in module for OTA. The Hoppers and Wallys use an add on USB OTA dongle. I believe they are entirely different.
Linus Tech Tips
· posted in Linus Tech Tips
0 Replies · 17 views
osu1991
Pub Member / Supporter
Last reply · posted in TV Shows
12 Replies · 256 views
osu1991
Finished the 2nd episode tonight. I'm really liking it so far.

Still hate weekly releases though, especially the way Disney and HBO do it waiting until 8pm to premiere it.
Foxbat
Apparently I'm not a big enough nerd🤓 since I did not read every Marvel Comic Book ever published. If I had, I might be comparing the comics' version of events compared to what's transpiring in "Visionquest". So, I am enjoying the series a lot, not weighed down by previous expectations, knowing only the Avengers MCU movies and the "Wandavision" / "Agatha All Along" TV series.

I found the Mr Know-it-All channel from his discussion about "Star Trek: Strange New Worlds" and he's been gleefully picking these episodes apart, referencing the Marvel comics from the 1939 on. Turns out A.I. has been around since before World War II, at least in the comics. (Robots before that, yes, yes.) This show is going back into the archives.
  • Like
Reactions: osu1991
Foxbat
I'm expecting the finale to basically bring Vision into play for the Doomsday movie next month.
  • Like
Reactions: osu1991
osu1991
annoying they went with single episodes for the last two after releasing two a week for the first 3 weeks
Foxbat
annoying they went with single episodes for the last two after releasing two a week for the first 3 weeks
I thought they were effectively releasing a longer episode 7 and 8 instead of shorter episodes 7 & 8 this week and 9 & 10 next week. It felt like they were packing more into this episode.

edit: But you're right, the run time of the first three pairs of episodes was 100 minutes on average. Episode 7 clocks in at 65 minutes. 😕