Social Feed

Badfish740
Last reply · posted in DISH Network Support Forum
I've had Dish Network for about four years. We opted for it when we moved into our new home because it was bundled with the local voice/data provider's services. I was unprepared for the install the first time because I had never had a satellite system before and didn't realize that it wasn't as simple as running one line to each box. In addition I had ripped all of the existing coaxial cable out of the house because all of it looked as old (house was built in 1968) as the house itself. The fact that I hadn't run my own wiring already meant that the tech had to run lines down the side of the house, drill holes in the walls, etc... My goal is to bring the lines into the attic near the satellite dish and then distribute them from there, fishing them down through the walls. I just need a good understanding of what needs to go where. I found the diagram detailing installation training for Dish techs learning to install the Hopper/Joey system:

Whoops, can't post links yet-in any event the diagram shows one line going directly from the node to the Hopper and one line going to a splitter and then on to two Joeys-my question (see below) is whether or not I should install the splitter inline with a terminator on one of the outputs (I'll only be using one Joey), or just run a single line to the Joey?

Is this the most straightforward way to install the system? One question I have is for right now I am only going to be getting the Hopper and one Joey as we only have two TVs. I was thinking of running the line from the node into the attic to a splitter, running one line off of the splitter to the Joey, and then placing a terminator on the other outlet of the splitter for now. That way it's already there and when I get another TV/another Joey I'll just remove the terminator and run the line. Is there any reason NOT to do it that way, ie: should I just run a single line to the Joey and not use the splitter at all? Then of course I'll run the other line to the Hopper as shown on the diagram along with ethernet. This will be easy since the Hopper will be in the basement in very close proximity to the router. Finally, what about the coaxial cable itself? Obviously I'll be doing all of the cable runs/fishing myself, so I was just going to buy bulk cable, run it, cut to length, and leave the bare ends for when the technician comes. I'd rather leave it to them to do to make sure that the crimps are done correctly, plus that means I don't have to spend another $50 on a crimping tool. I found a 250' spool of RG6 at Lowes for about $40. Any reason not to buy coax from a big box retailer? What specs should I look for on the cable, or is the fact that its stamped RG6 enough? I figure buying in bulk like this should cover me for now and for any future TVs I add. I know these are real noob questions, but I just want to make sure that I'm totally prepared when the installer arrives.
6 Replies · 2779 views
D
The end result with in-wall wiring will be worth the effort, but be prepared to some wall-busting when you run in to the fire-blocks inside the walls, viz. the 2" x 4" cross-members between the wall studs; and, the double-thickness "plate" at the top of the wall. I ran my cables through two stories, across an attic, and back down two stories. Get a good, extra long 3/4" spade bit for your power drill:)
D
Buying a spool of rg6 from a big box retailer is ok. Only problem is it may not be on the approved parts list for Dish installers. I myself would do your install and run with it but there may be a chance the installing tech may request to rerun approved wiring. Hopefully a current tech can weigh in on this more. As for buying a compression tool with fittings, again, chances are they wont be approved per Dish approved parts list and will be cut off and replaced anyway. I'm all for running 2 lines per outlet when you're doing your own install and have plenty of cable. I have 2 cable outlets in every room of my home but I also have satellite and cable run to every tv too. All in all, I think the tech who shows up will be pretty happy lines have been run and all he has to do is install fittings and a wall plate then map out lines.
Badfish740
Buying a spool of rg6 from a big box retailer is ok. Only problem is it may not be on the approved parts list for Dish installers. I myself would do your install and run with it but there may be a chance the installing tech may request to rerun approved wiring. Hopefully a current tech can weigh in on this more.

Thanks for the info-I hope a current tech can weigh in as well. The last guy who came out when I got Dish four years ago was not that great. I told him what I wanted done (and was ready willing and able to help) and he flat out told me that as an installer he was not qualified to fish cable through walls and could only run wire on the outside of the walls using screw in cable clips, etc... We did our best to hide it with furniture and other things, but it looks horrible, and there's no hiding what is on the outside of the house. That's what gave me the idea to run it all myself and just have them handle the connections and setting up the boxes. Now I'm nervous that I could end up doing all this work for nothing.

All in all, I think the tech who shows up will be pretty happy lines have been run and all he has to do is install fittings and a wall plate then map out lines.

I hope this is the case. Would there be any way to find out what is on the approved parts list and try to source the cable that way?
Dishman1978
Any Rg6 3ghz rated cable to your Hopper location will do. Vextra is the brand name we install hereon the west coast but it really doesn't matter the brand as long as its ratedfor 3GHz. Putting a splitter in when only one Joey isn't really necessarry, you could always do that when a second Joey is installed. Plus 2 cables from the dish to your junction is a must, but a 3rd wouldnt hurt as making it easier for a second Hopper to be installed at a later date, if you choose to.

I wouldn't even bother putting fittings on the cable as the tech will most likely just cut them off to install thief.own approved ones.

But if your running all the cables and.fishing them your self that's awesome. I'd love that if all my jobs were that simple.

And yes, I am currently an installer, FSS 4 to be exact.
elmafu69
I ran my cabling even installed hdmi over ethernet adapters. All the installer did was clip the caps cuz he didnt like them and to be honest his were of a much higher quality. It did save him a lot of time though.
Ramy
Supporting Founder
Last reply · posted in The Sports Section
Really excited for this season with Kentucky having a new coach and some really exciting recruits. Probably won't last long, but here's hoping this season is great.
152 Replies · 1897 views
  • Haha
Reactions: Mike0616
Foxbat
Best fan sign I saw during the ND-BYU game: "Bear ate your Lucky Charms!" (Bear being the Cougars' QB). I was going to suggest, "Have you or your team been involved in a Carr crash?"
  • Haha
Reactions: Jimbo and Mike0616
M


They get cruel sometimes, very very cruel.😈. Hated to see my dawgs go down but I still say being ranked #1 is a hex on you!
  • Like
Reactions: Howard Simmons
Jimbo
They get cruel sometimes, very very cruel.😈. Hated to see my dawgs go down but I still say being ranked #1 is a hex on you!
Yup, I agree, I'd rather be 2 or 3 till the last few weeks.
meStevo
Lifetime Supporter
Last reply · posted in The Sports Section
Schedule drops tomorrow. Mandatory mini camps in June. Hall of Fame game August 6th.
113 Replies · 1795 views
  • Like
Reactions: Jimbo and dfergie
osu1991
  • Like
Reactions: Mike0616
M
Hopefully nowhere near a microphone.
Y
Hopefully nowhere near a microphone.
After having experienced Gus Ferguson trying to call soccer games, I'm uncertain why NFL football analysts get hate. Even the "worst" of them are pretty good.
meStevo
Jalen Hurts out indefinitely as they treat and monitor a superficial blood clot in his leg.


View: https://x.com/RapSheet/status/2111074303185989663?s=20
  • Sad
  • Wow
Reactions: Mike0616 and Foxbat
meStevo
Browns lead the AFC North 🤣

Seth Meyers What GIF by Late Night with Seth Meyers
Foxbat
I guess even the patience of us laid-back Hoosiers has its limits:
Peter Parker
Supporting Founder Lifetime Supporter
Last reply · posted in DISH Network Support Forum
No idea what improvements might be involved.
23 Replies · 980 views
  • Like
Reactions: LQQK and reubenray
bookworm370
Has anyone noticed an FF stutter with 713? I used to be able to hit FF a few times and skip smoothly. After 713 (maybe 712), when I skip forward, there is a definite stutter for as many times as I have pressed FF.

Can anyone check on this and report back? Recorded programs and then press skip forward a few times to see if it's smooth? Normally, it just jumps to the right place after the skips.
  • Like
Reactions: charlesrshell
N
I'm getting fabulous picture on Ch. 148 4k, but zero audio with H713. This is with a recorded show (Notre Dame game). Anyone else have this? Audio is fine on every other channel.
  • Like
Reactions: charlesrshell
R
Has anyone noticed an FF stutter with 713? I used to be able to hit FF a few times and skip smoothly. After 713 (maybe 712), when I skip forward, there is a definite stutter for as many times as I have pressed FF.

Can anyone check on this and report back? Recorded programs and then press skip forward a few times to see if it's smooth? Normally, it just jumps to the right place after the skips.
My wife mentioned that her remote is acting strange this morning. She hit FF and it went to 15x FF.
  • Like
Reactions: charlesrshell
Foxbat
Wife bought me a t-shirt that has "have you tried turning it off and on again?"
Here's the one I need:
1792365258110.webp
dishstaller
Here's the one I need:
Just ordered one....that's great.
jsmit86
I'm getting fabulous picture on Ch. 148 4k, but zero audio with H713. This is with a recorded show (Notre Dame game). Anyone else have this? Audio is fine on every other channel.
It's a known issue.
For a temporary fix, go into the menu, Audio, and turn Dolby Audio "OFF". You will have PCM stereo audio.

I was able to give the tech ops team some data logs so they could diagnose the problem, and they rolled me back to H708 temporarily. It fixed that issue.

They let me know that they understand what caused the issue, and it will be fixed within a few weeks in a new update.
long_time_Dish
They let me know that they understand what caused the issue, and it will be fixed within a few weeks in a new update.
Oh, you mean "soon"? :biggrin
Almighty1
It's a known issue.
For a temporary fix, go into the menu, Audio, and turn Dolby Audio "OFF". You will have PCM stereo audio.

I was able to give the tech ops team some data logs so they could diagnose the problem, and they rolled me back to H708 temporarily. It fixed that issue.

They let me know that they understand what caused the issue, and it will be fixed within a few weeks in a new update.
I guess they will be busy when lots of people start asking for rollbacks to H708 now that you mention that downgrades of software does exist because it will likely fix the OTA Single Tuner and the IR Remote problems in H710-H713.
  • Like
Reactions: charlesrshell
navychop
it will likely fix the OTA Single Tuner

:popcorn
  • Like
Reactions: charlesrshell
SuperDish_Fan23
Last reply · posted in DISH Network Support Forum
Why are ViP922s So rare? like its crazy how ebay has none, i checked everywhere, also, i got a ViP222k now, which is actually activated!
7 Replies · 197 views
HipKat
I think they were more of a transitional receiver bridging the VIPs to the Hopper. They were a PITA to install and were buggy. Personally, I thought at the time that they were the best receiver out there. The versatility of the VIP's with the new Hopper GUI and, by far, the coolest-looking front plate and lighting.
AZ.
AZ.
Well if it is because of reliability that wouldnt shock me.I went through 5 or 6 of them in little over 2 years. I loved the Sling when it worked! Saved lots of money having it in the day. That was probably 15 or 16 years ago?
T
I think they were more of a transitional receiver bridging the VIPs to the Hopper. They were a PITA to install and were buggy. Personally, I thought at the time that they were the best receiver out there. The versatility of the VIP's with the new Hopper GUI and, by far, the coolest-looking front plate and lighting.
I don't recall that they came out just before hopper, but rather that they came out even before 722. Or could be thinking of 921.

As to the title pf the post, "rare" does not necessarily mean valuable or desirable.
Nominal
I don't recall that they came out just before hopper, but rather that they came out even before 722. Or could be thinking of 921.

As to the title pf the post, "rare" does not necessarily mean valuable or desirable.
You are thinking of the 921. The 922 was the first DVR with Sling functionality built in (that was eventually disabled along with the Sling Adapter for the 722s and the 1st Hopper because they relied on now-defunct Adobe Flash technology). With the bugginess described by others and the removal of its marquee feature (Sling) the 922 faded into obscurity once the Hopper 2 with built in Sling was released and they finally made the concept into a fully functional product.
dishdude
I had one, the front panel lighting was cool, the menus were fresh and a lot more modern looking than the ViPs. However, it was very buggy and the Sling functionality just didn't work well - I think it was due to internet speeds at the time. I think I had to pay $40 for the Sling app on my phone iirc.
  • Like
Reactions: charlesrshell
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in The Chit Chat Club
Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne


Get it?


An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
68534 Replies · 2673281 views
  • Like
Reactions: c-spand
ClarkGable
Take It To The Limit - The Eagles
harshness
Take It To The Limit - The Eagles
The two instances of "The" should have been highlighted.

Take
Me to the River - Talking Heads
dishstaller
Blinded By The Light - Manfred Mann's Earth Band
Bobby
I Saw The Light - Todd Rundgren
long_time_Dish
Little Bit Of Light - Strange Weather
  • Like
Reactions: dishstaller
EatMyVolts
A Little Bit of Soap -- The Jarmels
dfergie
Staff member HERE TO HELP YOU!
Last reply · posted in What's Cooking?
We have a Breakfast and Dinner thread so... :)
Continuing from the Breakfast thread, found Cornbread mix so ...
Yellow Cornbread Mix
2 Hatch Green Chiles -diced
1 Egg
2/3 cup of milk
add to greased pan
Bake for 400f 20-25 minutes(From instructions)
now to put together and try... this to go with pinto beans...
5446 Replies · 335531 views
TRG
TRG
Two Chicago style hot dogs and a Fanta orange soda.
  • Like
Reactions: Bobby and dfergie
M
Little mini pepperoni pizza, green beans, apples and chocolate milk.
  • Like
Reactions: dfergie
dfergie
Fanta orange soda.
Sitting in fridge cooling off, bought 1 along with 2 Mexican Cokes at La Tienda... (I keep a few cokes stashed as well as in fridge and camper fridge)
  • Like
Reactions: TRG and Mr Tony
M
Garlic cheese bread
Green beans
Apples
Chocolate Milk
Some weird noodles. ;)
(They have salad and a couple other fruits if wanted)
  • Like
Reactions: dfergie
TRG
TRG
Club sandwich and corn chowder. Iced tea.
dfergie
Chili dog bowl, water… (homemade chili)
dfergie
Staff member HERE TO HELP YOU!
Last reply · posted in TV Shows
Stargate SG-1 cancelled, Atlantis renewed
clear.gif

Monday - August 21, 2006 | by Darren Sumner
clear.gif

The future of Stargate is in question today, as SCI FI Channel has cancelled the long-running Stargate SG-1, Multichannel News reported today and a GateWorld source has confirmed. The news regrettably follows the airing of the show's milestone two-hundredth episode on Friday.

Stargate Atlantis, meanwhile, has been renewed for a fourth season, with the network hoping to see that the spin-off series can stand alone, according to a source.
Source Gateworld
2032 Replies · 184102 views
dfergie
The Tokra pt 1, I know pt 2 will be next...
(came across on Pluto tv live, went to media server for "clean" version)
R
I have gotten back into watching SG-1 and I have recorded most of the episodes to binge watch. What episodes are about the Antarctic or was this a movie? Also where could I watch the SG-1 movies?
osu1991
long_time_Dish
I have gotten back into watching SG-1 and I have recorded most of the episodes to binge watch. What episodes are about the Antarctic or was this a movie? Also where could I watch the SG-1 movies?
Well, there are a couple involving the Antarctic. "Solitudes", S1 E17 (one of my favorites), Then, "Lost City', S7 E21 and E22. Then, in the SGA pilot, "Rising", S1 E1 and E2, it starts out in the Antarctic for about the first 20 minutes or so.
R
Well, there are a couple involving the Antarctic. "Solitudes", S1 E17 (one of my favorites), Then, "Lost City', S7 E21 and E22. Then, in the SGA pilot, "Rising", S1 E1 and E2, it starts out in the Antarctic for about the first 20 minutes or so.
Which one has O'Neil being Ancients? I am at the end of Season 8 now.