Social Feed

mheisen said:

Over the past few weeks, I have had problems connecting to streaming services (Netflix, HBO et al). When I go to the TV's native Channels, I have no problem. The Dish internet troubleshooter shows I have a good internet connection. I'm wondering whether it's an issue with my internet provider or a problem with the Dish software on the Hopper Plus. Anyone else seeing this?

Click to expand...

Almighty1 said:

I have a DISH Hopper 3 (Software H713) with Hopper Plus (Software P15403). I have not tried streaming services but I primarily watch TVB Jadeworld international package which is only available by streaming and when I have an issue, I usually have to go to a non-streaming satellite channel first before the streaming channels will work again. What software versions do you have and what is the error message if any are showing on your screen? or is that Dish downloading logo just stuck and never finishes?

Click to expand...

mheisen said:

I'm on H713 on the Hopper and P15403 on the Hopper Plus. It shows internet connection issues and doesn't finish loading the various services. I see the "loading circle going around. Sometimes I get a message saying that the service is having trouble loading my content and to check the internet connection.

Click to expand...

Almighty1 said:

Did it ever work correctly before? Hard to say what the problem is. Usually for streaming, it will show the Dish logo with lines sweeping down to show downloading, never seen the circle issue. Did you try a manual reboot, red button reset, power cord unplug/replug to see if it makes a difference.

Click to expand...

mheisen said:

Over the past few weeks, I have had problems connecting to streaming services (Netflix, HBO et al). When I go to the TV's native Channels, I have no problem. The Dish internet troubleshooter shows I have a good internet connection. I'm wondering whether it's an issue with my internet provider or a problem with the Dish software on the Hopper Plus. Anyone else seeing this?

Click to expand...

slow_poke_pete said:

Might be worth just to ditch the hopper plus. No issues here on h713

Click to expand...

slow_poke_pete said:

Buy a roku and dump the hopper plus you'll be better off. If you have a smart tv you don't need either one. No hopper plus here and no issues!!!

Click to expand...

jsmit86 said:

If the OP has a router and a managed switch, that could be the problem.
I have a Hopper 3 and 5 Joey 4s. I recently updated my Router, Switch and access points with Ubiquiti UniFi gear. I had an issue where the switch interpreted the communication between the hopper internet connection and one of the Joeys as a data loop. I had to change some settings in the switch to re-enable that port. Your router could possibly be doing the same thing blocking the connection.

If your router has a malware connection setting, try disabling it temporarily, and see if the internet comes back. Contact your ISP and see if there is a block happening at the router or switch level, or via the ISP's threat protection.

Click to expand...

• • TCP Port 80 – HTTP communication
  • TCP Port 443 – HTTPS secure communication
  • TCP Port 5678 – Neighbor Discovery / Device Sync
  • UDP Port 80 – Alternative streaming/network data
  • UDP Port 443 – Alternative secure media streams
  • UDP Port 5678 – Remote pairing and network discovery

• • UPnP (Universal Plug and Play): Enabling UPnP on your router is the easiest way to allow the Hopper to automatically handle its own port maps.
  Internal Communication (MoCA & Local LAN): The Hopper Plus and Joeys communicate internally over your local home network using router's default internal traffic policies. Local firewall software or strict internal VLAN isolation can block the Hopper 3 from seeing the Hopper Plus or Joey extensions.
  
  The other thing is that these are streaming channels which was why I asked if they have worked correctly even without the Hopper Plus as checking the post history of the OP, it appears that the Hopper Plus was added around 1/2 a year ago and from looking at my own Internet settings portion, all the Hopper 3 does is really measure signal strenth for WiFi and probably just check ping times to show it is connected or not to the internet, it does not check the actual speed or latency. Since the OP has a Hopper Plus, OP can always install the Speedtest app for diagnostics and then take a photo of the results and post it here. Before 2017, I used tȯhave 6Mbps/768Kbps ADSL and even though the Hopper 1 and Hopper 3 also showed internet connectivity is okay, everytime my Ring Doorbell is uploading, it would knock the entire internet connection off-line as the upload pipe would be 100% filled by the Ring Door bell uploading the video because the ACKnowledgement packets would not have priority being sent back in time which was fixed with QoS traffic shaping but that still does not mean streaming will work as it requires at least 25Mbps minimum or more if there are other devices on the same connection sharing the bandwidth.
  
  
  ​

Almighty1 said:

Can you share what settings you had to change?

Required Inbound & Outbound Network Ports
The standard ports designated for DISH Hopper configurations include:

• • TCP Port 80 – HTTP communication
  • TCP Port 443 – HTTPS secure communication
  • TCP Port 5678 – Neighbor Discovery / Device Sync
  • UDP Port 80 – Alternative streaming/network data
  • UDP Port 443 – Alternative secure media streams
  • UDP Port 5678 – Remote pairing and network discovery

Critical Network & Security Considerations

• • UPnP (Universal Plug and Play): Enabling UPnP on your router is the easiest way to allow the Hopper to automatically handle its own port maps.
  • Internal Communication (MoCA & Local LAN): The Hopper Plus and Joeys communicate internally over your local home network using router's default internal traffic policies. Local firewall software or strict internal VLAN isolation can block the Hopper 3 from seeing the Hopper Plus or Joey extensions.The other thing is that these are streaming channels which was why I asked if they have worked correctly even without the Hopper Plus as checking the post history of the OP, it appears that the Hopper Plus was added around 1/2 a year ago and from looking at my own Internet settings portion, all the Hopper 3 does is really measure signal strenth for WiFi and probably just check ping times to show it is connected or not to the internet, it does not check the actual speed or latency. Since the OP has a Hopper Plus, OP can always install the Speedtest app for diagnostics and then take a photo of the results and post it here. Before 2017, I used tȯhave 6Mbps/768Kbps ADSL and even though the Hopper 1 and Hopper 3 also showed internet connectivity is okay, everytime my Ring Doorbell is uploading, it would knock the entire internet connection off-line as the upload pipe would be 100% filled by the Ring Door bell uploading the video because the ACKnowledgement packets would not have priority being sent back in time which was fixed with QoS traffic shaping but that still does not mean streaming will work as it requires at least 25Mbps minimum or more if there are other devices on the same connection sharing the bandwidth.
    

Click to expand...

rvvaquero said:

That's a lot of information to ingest. However, I don't have the Hopper Plus and my 54 remote is doing crazy things to the Hopper 3. Several times each evening when I press the skip forward button several times to advance through a commercial, it switches the receiver either onto live TV or into suspension. Other buttons will also cause this randomly, I haven't established any patterns I can describe. I use "recall" to go back to my recorded program in progress.

Needless to say, something in the newer Hopper 3 softwares has caused the remote functioning to ......................malfunction. Evidently, it applies to third party remotes as well as DISH's own remotes.

Click to expand...

Foxbat said:

I'm at a limit for TV sizes at this time. My Father-in-Law crafted a custom entertainment center for our family room and we were restricted from going too big based on the side cabinets and central bridge fitting in the width of the room. It turns out to be where a 55" screen with bezels fits but no 65" bezel-less screen can fit. I think there was a brief period where 58" screens where a thing, but no more.

So, no huge screens for the Foxbat's…

Click to expand...

TRG said:

55" is plenty big.

Click to expand...