Social Feed

Rdeejr
Last reply · posted in DISH Network Support Forum
Tech just installed Hopper 3. If H3 has 16 tuners and one is used for PTAT then that would mean 19 shows can be recorded at once? 15 + 4 on PTAT.

Is this correct?
16 Replies · 2763 views
Rdeejr
For me it's not about recording 20 shows at once. It's about no more conflicts. Set timer and let it rip.
MikeD-C05
For me it's not about recording 20 shows at once. It's about no more conflicts. Set timer and let it rip.
I guess I never thought about this perk. It would be nice to never have to worry about conflict screens and resolving them all the time. I have had to do it so often that I set my timers up in order that would cause the least amount of conflicts. Luckily most of my wife's shows are repeated again later in the night , so her show timers are last in order and it catches the later times.
  • Like
Reactions: charlesrshell
charlesrshell
I guess I never thought about this perk. It would be nice to never have to worry about conflict screens and resolving them all the time. I have had to do it so often that I set my timers up in order that would cause the least amount of conflicts. Luckily most of my wife's shows are repeated again later in the night , so her show timers are last in order and it catches the later times.

Yep, I hear ya. I have a lot of conflict issues mostly because I have added 10 minutes end late time to most timers. My wife gets pretty upset when the recording end gets cut off because of the guide and prgrams not ending at correct time. I can't wait for when the new DPH42 switch comes out so I can change over to the Hopper 3.
  • Like
Reactions: MikeD-C05
bookworm370
Yep, I hear ya. I have a lot of conflict issues mostly because I have added 10 minutes end late time to most timers. My wife gets pretty upset when the recording end gets cut off because of the guide and prgrams not ending at correct time. I can't wait for when the new DPH42 switch comes out so I can change over to the Hopper 3.

Charles, Why are you waiting for the DPH42 switch before you can change over to the H3? Is it because you want 2 Hopper 3's?
  • Like
Reactions: charlesrshell
charlesrshell
Charles, Why are you waiting for the DPH42 switch before you can change over to the H3? Is it because you want 2 Hopper 3's?

Because I think my 1000+ dish is the better dish, hardly have any rain fades. This 1000+ Western Arc dish also includes the International 118.7 bird, why should I have to mount a wing dish. There isn't a new hybrid DPH LNB for the 1000+. Apparently DISH wanted to get this Hopper 3 out quick so the new Hybrid LNBs were manufactured based on the most common installs. If my 1000+ dish had the new hybrid LNB I probably would switch to the new Hopper 3 and then wait for the new DPH42 switch for a second Hopper 3. So, got to be patient and wait on the new switch so I can keep my 1000+ dish and have a second Hopper 3 too. Here is what Vivek Khemka said: Available towards the end of this year. We will have a new switch DPH42 – that will support using your existing 1000+ DISH and existing LNB and will also allow you to have more than one Hopper 3. So you will not require a 2nd DISH, will not have to change your current LNB and you can have multiple Hopper3's. Since this part is still under development, I do not have a more specific date than Q4-2016 at this time.
M
And hopefully someday you will be able to have two H3's!
  • Like
Reactions: charlesrshell
BlackHitachi
Supporting Founder
Last reply · posted in Movie Talk
Since the Reds have there thread we should too!

Last watched Nine inch Nails
Next 3:10 to Yuma
5397 Replies · 511757 views
dfergie

Last of the Dogmen is my favorite of hers.
  • Like
Reactions: osu1991
"MysteryMan"
Gone.webp
osu1991
Star Wars Despecialized Edition

IMG_0803.webp
dishstaller
Just watched Napoleon. Good night.....all of those young men dying for the egos of their leaders. Now we can kill at a distance, back then you saw the man you were killing eye to eye.
comfortably_numb
Pub Member / Supporter
Last reply · posted in Internet Television (IPTV) Discussion Forum
Not sure saving $24/year is worth it unless you're a hardcore Philo user. I'll stick with monthly.

IMG_0351.webp
7 Replies · 225 views
Jimbo
Not sure saving $24/year is worth it unless you're a hardcore Philo user. I'll stick with monthly.

View attachment 195247
$24 for the Year, would be more useful.
Howard Simmons
$24 for the Year, would be more useful.
But when you cancel you still have to watch until the plan runs out. With monthly you're done at the end of the month.
Jimbo
But when you cancel you still have to watch until the plan runs out. With monthly you're done at the end of the month.
Sorry, my point was the expense.
comfortably_numb
$24 for the Year, would be more useful.

Philo's monthly price is reasonable, IMO, because it's still the cheapest way I'm aware of to get all the linear Discovery networks AND access to the Discovery Go apps.
  • Like
Reactions: Howard Simmons
Jimbo
Philo's monthly price is reasonable, IMO, because it's still the cheapest way I'm aware of to get all the linear Discovery networks AND access to the Discovery Go apps.
I guess if it was something I used on a regular basis, I suppose.
  • Like
Reactions: Howard Simmons
comfortably_numb
In other Philo news..

IMG_0364.webp
Bobby
Oh boy, I can't wait! 😂
K
Pub Member / Supporter Lifetime Supporter
Last reply · posted in TV Shows
'Rockford Files' Reboot Gets NBC Pilot Order

I grow tired of all the reboots. Most I don't bother with but will depend on the actor chosen.
19 Replies · 749 views
long_time_Dish
Yeah, I'll check it out as well, but shan't be holding my breath...It'll be tough to equal James Garner in that role...
  • Like
Reactions: Foxbat
harshness
...It'll be tough to equal James Garner in that role...
I can think of a few actors (including some females) who might fit the bill.

This will all depend on the storyline. I'm not sure how well it will translate. Modern TV hasn't been all that kind to PIs and even less kind to CIs (confidential informants).
K
Premier is Saturday, Jan 2nd. Moving to Thursday on the 7th.
long_time_Dish

I wonder how they're/if they're going to do something like the answering machine message opening? It was always funny...
  • Like
Reactions: dfergie
meStevo
Lifetime Supporter
Last reply · posted in The Chit Chat Club
Continuing the Kilauea thread in the Pub here. Perhaps the Iceland one too next time there's remarkable activity.

Currently there is precursory lava flowing into the crater, leading to the next episode that'll probably start within the next day.

You can see the pace of inflation / deflation here. It serves as the primary predictor for when the expect the eruptions, which coincide w/ inflation turning into significant deflation and last for several hours on average with significant fountaining.



View: https://youtu.be/Uecu2seh4b4


Wife and I like the AfarTV feeds, for the discussion along w/ them, though they're otherwise just mirrors of the official USGS feeds.


View: https://youtu.be/iws3rh5vLAQ
123 Replies · 3690 views
  • Like
Reactions: osu1991
Foxbat
Kīlauea seems to be returning to the "normal" eruption script, impressive fountaining from the North Vent. For once, the V2 Cam has the best overall shot:
IMG_1535.webp
The lava flows have covered a good portion of the Halemaʻumaʻu crater floor.
Foxbat
Looks like Episode 55 is over at 09:00 HST, just under six hours. The USGS said the fountains reached 720' or 220 meters.
​
  • Like
Reactions: RaiderPower
Foxbat
The USGS Kīlaeua Webcam #1 has been showing overflows and doming from the North vent overnight. Maybe the volcanic plumbing has settled back into its two-three week cycle of fountaining?

But I do miss the little cinder cone that broke up in the last episode.
Foxbat
Sorry, I should have posted these earlier:

​

We're still waiting on the start of Episode 56.
  • Like
Reactions: RaiderPower
Foxbat
At 08:01 HST 11/05/2026, the North Vent produced what I would call a "wet burp" after the precursory "pistoning" events, small amounts of lava pouring out of the vent for a few seconds to minutes and then everything recedes. There must have been a gas bubble holding thing back because two minutes later the lava started flowing out of the vent in all directions. Then, at 08:25, it stopped. What a tease! I thought this was how Episode 56 started.

About 12 minutes later at 08:38, the North vent once again started overflowing and picked up steam at 08:42. By 09:00, slight doming could be seen in the pool of lava in the vent. Surely this is it!

But, 09:50 and things wind down again. By 09:57 HST there's just fumes coming out of the vent. Phooey.

But then 10:00 comes and the heavy lava flows kick in again. This time seems like the real deal. At 10:30 HST there's little spurts of lava flying up in the air over the vent, but more from gas than a steady fountain of lava. This looks promising!

11:30 HST and the color of the lava is definitely hotter, and the intensity has picked up to a definite dome and precursor to fountaining. The USGS calls Episode 56 as officially starting at 12:10 HST:

Alert Level: WATCH, Color Code: ORANGE 2026-11-05 22:29:12 UTC
HVO/USGS Volcanic Activity Notice

Volcano: Kilauea (VNUM #332010)

Current Volcano Alert Level: WATCH
Current Aviation Color Code: ORANGE

Issued: Thursday, November 5, 2026, 12:29 PM HST
Source: Hawaiian Volcano Observatory
Notice Number: 2026/H514
Location: N 19 deg 25 min W 155 deg 17 min
Elevation: 4091 ft (1247 m)
Area: Hawaii

Summary: Episode 56 of the ongoing Halemaʻumaʻu eruption began at 12:10 PM HST on November 5, 2026.

Volcanic Activity:
Episode 56 of lava fountaining in Halemaʻumaʻu began at the summit of Kīlauea began at 12:10 PM HST on November 5, 2026.

Lava fountain heights are relatively low at about 100 ft (30 meters), but will likely increase. Ground-level sensors near the eruptive vents indicate that winds are blowing from the northeast direction, which suggests that volcanic gas emissions and volcanic material may be distributed to the southwest direction from Halemaʻumaʻu.
  • Like
Reactions: meStevo
osu1991
Pub Member / Supporter
· posted in Movie Talk
0 Replies · 18 views
osu1991
Pub Member / Supporter
· posted in Movie Talk
0 Replies · 24 views
M
Last reply · posted in DISH Network Support Forum
I have Dish with Hopper3. I choose to get local channels OTA and had a "guide list" established at my previous home. Having moved a few miles away, I wanted to update the list by appending a couple new stations via a rescan. As many would know, some stations come in with the UHF/VHF antenna aimed in one direction, while others come in better with a different direction.

Unfortunately, when a scan is done (bringing in 25-30 stations for that particular antenna aim), the dialog screen does not present the established guide list; it presents an empty field to the right that the scanned stations may be selected one by one and added to the empty guide. But because of antenna aim, some stations originally saved are missing, and would have to be retrieved with a different antenna aim. But as I explain, if a 2nd​ scan is done with a different antenna aim, the stations saved from the first scan are lost.

It troubles me that Dish didn't develop software that would allow a user to simply append only 1 or 2 channels to the established list. :mad:

Any thought on this? Has anyone experienced this or heard of this from others?
15 Replies · 511 views
dishstaller
I could very well be wrong....it has been a LOT of years but back when I had a 722K it seemed like when you went back to the scan screen that you could just scan again and it would ADD those channels to the previous list or you could delete the previous results and only add the channels from the new scan.
  • Like
Reactions: charlesrshell
N
I could very well be wrong....it has been a LOT of years but back when I had a 722K it seemed like when you went back to the scan screen that you could just scan again and it would ADD those channels to the previous list or you could delete the previous results and only add the channels from the new scan.
I am not sure about that but I do know that you could manually add additional channels just by entering the actual RF channel number and the older receivers would add the virtual channels to your list
dishstaller
I am not sure about that but I do know that you could manually add additional channels just by entering the actual RF channel number and the older receivers would add the virtual channels to your list
Like I said.....that has been many years ago. Swapped my 722K for a Hopper in 2012.

It does seem like I remember having to delete the existing channels when we did a rescan. Back then our local stations KEPT monkeying around with things and it was non-stop complaints from customers about their channels not coming in. Got so bad that I stopped selling OR installing OTAs....something I had been doing since 1984 so you know it HAD to be pretty bad.
M
You made one of my points for me with this comment, Dishstaller:

"... local stations KEPT monkeying around with things and it was non-stop complaints from customers about their channels not coming in ..."
dennispap
I could very well be wrong....it has been a LOT of years but back when I had a 722K it seemed like when you went back to the scan screen that you could just scan again and it would ADD those channels to the previous list or you could delete the previous results and only add the channels from the new scan.
I remember that also on my 722.
dishstaller
I remember that also on my 722.
Thanks.....has been too many years to remember clearly.
  • Like
Reactions: charlesrshell
Bobby
Keep in mind that the 722 had a built in OTA tuner and the 722K had a plug in module for OTA. The Hoppers and Wallys use an add on USB OTA dongle. I believe they are entirely different.
Linus Tech Tips
· posted in Linus Tech Tips
0 Replies · 17 views
osu1991
Pub Member / Supporter
Last reply · posted in TV Shows
12 Replies · 256 views
osu1991
Finished the 2nd episode tonight. I'm really liking it so far.

Still hate weekly releases though, especially the way Disney and HBO do it waiting until 8pm to premiere it.
Foxbat
Apparently I'm not a big enough nerd🤓 since I did not read every Marvel Comic Book ever published. If I had, I might be comparing the comics' version of events compared to what's transpiring in "Visionquest". So, I am enjoying the series a lot, not weighed down by previous expectations, knowing only the Avengers MCU movies and the "Wandavision" / "Agatha All Along" TV series.

I found the Mr Know-it-All channel from his discussion about "Star Trek: Strange New Worlds" and he's been gleefully picking these episodes apart, referencing the Marvel comics from the 1939 on. Turns out A.I. has been around since before World War II, at least in the comics. (Robots before that, yes, yes.) This show is going back into the archives.
  • Like
Reactions: osu1991
Foxbat
I'm expecting the finale to basically bring Vision into play for the Doomsday movie next month.
  • Like
Reactions: osu1991
osu1991
annoying they went with single episodes for the last two after releasing two a week for the first 3 weeks
Foxbat
annoying they went with single episodes for the last two after releasing two a week for the first 3 weeks
I thought they were effectively releasing a longer episode 7 and 8 instead of shorter episodes 7 & 8 this week and 9 & 10 next week. It felt like they were packing more into this episode.

edit: But you're right, the run time of the first three pairs of episodes was 100 minutes on average. Episode 7 clocks in at 65 minutes. 😕