Social Feed

WhiteBeard
Pub Member / Supporter
Last reply · posted in Free To Air (FTA) Discussion
I want to replace a 2-wire reed sensor with a 3-wire hall sensor in a Venture actuator. Is there a way to make this work with a Gbox? I believe that I need to get +5VDC and ground out to the hall sensor, which won't be too difficult, but can the Gbox function OK with just one sensor wire? Does anyone have a schematic for the Gbox?
52 Replies · 7326 views
WhiteBeard
Is it possible to open up a reed sensor enclosure and replace the reed with just a hall sensor itself or does the hall sensor need any additional circuity? The hall sensor enclosure seems to be the same as a reed sensor enclosure but, of course, the hall sensor needs 3 wires. I haven't opened up a hall sensor enclosure to see what's inside. I'm wondering if a simple swap out of a reed for a hall sensor can be done to save a few bucks or should I just part with the $50 to get a hall sensor assembly from Venture. Apparently, Venture won't sell the hall sensor without the magnet (which looks exactly like the magnet for the reed sensor) or without the standoff (which looks exactly like the standoff for the reed sensor).
M
Is it possible to open up a reed sensor enclosure and replace the reed with just a hall sensor itself or does the hall sensor need any additional circuity? The hall sensor enclosure seems to be the same as a reed sensor enclosure but, of course, the hall sensor needs 3 wires. I haven't opened up a hall sensor enclosure to see what's inside. I'm wondering if a simple swap out of a reed for a hall sensor can be done to save a few bucks or should I just part with the $50 to get a hall sensor assembly from Venture. Apparently, Venture won't sell the hall sensor without the magnet (which looks exactly like the magnet for the reed sensor) or without the standoff (which looks exactly like the standoff for the reed sensor).
Would like to see pictures of all that. Hard to visualize all what you're saying without having looked at one of those actuators before. One thing I have run into while fiddling around with sensors is the old actuators have a 5 wire barrier block and the reed switch ones have a 4 wire barrier block. I have had to reposition one to accommodate a new sensor. I have an old Venture actuator that uses a cog drive belt. Looks just like ones that don't have a belt. The belt is old and about to break in the one I have. I have yet to find any replacements for it either.
WhiteBeard
Would like to see pictures of all that. Hard to visualize all what you're saying without having looked at one of those actuators before. One thing I have run into while fiddling around with sensors is the old actuators have a 5 wire barrier block and the reed switch ones have a 4 wire barrier block. I have had to reposition one to accommodate a new sensor. I have an old Venture actuator that uses a cog drive belt. Looks just like ones that don't have a belt. The belt is old and about to break in the one I have. I have yet to find any replacements for it either.
Not sure of what you're asking for but here images from both the actuator for the TEK2000 and KTI. Both actuators are Venture. The TEK2000 is using a hall sensor and the KTI is using a reed. They both mount the same and look the same except the hall has 3 wires and the reed 2 wires.
M
Not sure of what you're asking for but here images from both the actuator for the TEK2000 and KTI. Both actuators are Venture. The TEK2000 is using a hall sensor and the KTI is using a reed. They both mount the same and look the same except the hall has 3 wires and the reed 2 wires.
Well no wonder I couldn't figure out what you were talking about. That so called hall effect sensor is the strangest thing I ever saw. ;) I pulled a reed sensor apart and replaced the reed in the housing and changed the magnet wheel. This tripled the counts from the sensor.
VentureMod sensor.jpg
WhiteBeard
Well no wonder I couldn't figure out what you were talking about. That so called hall effect sensor is the strangest thing I ever saw. ;) I pulled a reed sensor apart and replaced the reed in the housing and changed the magnet wheel. This tripled the counts from the sensor.
View attachment 149513
Where can I get these magnet wheels? I've been trying to find just a magnet wheel but it seems that I have to order a reed or hall sensor kit in order to get a magnet.
M
Where can I get these magnet wheels? I've been trying to find just a magnet wheel but it seems that I have to order a reed or hall sensor kit in order to get a magnet.
I made those wheels. The clear one is two pieces of plexiglass glued together. I cut them with a hole saw. The magnets are cheap. K&J Magnetics Inc. kjmagnetics.com
  • Like
Reactions: FTA4PA
WhiteBeard
I made those wheels. The clear one is two pieces of plexiglass glued together. I cut them with a hole saw. The magnets are cheap. K&J Magnetics Inc. kjmagnetics.com
I suppose that I could try my hand at doing that but I prefer factory built. I suppose that I need to get magnetic bars that end up sandwiched between the 2 pieces of plexiglass? And how did you cut that square hole in the center of the plexiglass? I'm surprised that I can't find a distributor of magnetic wheels outside of an actuator manufacturing firm. I get my actuators from Venture but they don't seem to be willing to sell just the wheel magnet.
M
I suppose that I could try my hand at doing that but I prefer factory built. I suppose that I need to get magnetic bars that end up sandwiched between the 2 pieces of plexiglass? And how did you cut that square hole in the center of the plexiglass? I'm surprised that I can't find a distributor of magnetic wheels outside of an actuator manufacturing firm. I get my actuators from Venture but they don't seem to be willing to sell just the wheel magnet.
I used a 2" hole saw with a 1/4" pilot bit. This creates disks about 1-3/4" with a 1/4" hole in the center. I cut two of them from 1/16" thick material such as the plexi-glass. In one disk I drill (6 ) 3/16" holes around the edge to hold the disk magnets measuring 3/16" wide and 1/16" thick. (#D31-N42 from K&J Magnetics) I epoxy the disks together and insert the magnets (all polarized the same way) into the disk with the holes. I then take a small triangle file to the center hole and make the four corners of the square hole. The wheel is mounted magnet side to the reed switch.

However this is a wheel I designed for a reed switch and have no idea about it working with your three wire sensor.
  • Like
Reactions: clucas and FTA4PA
WhiteBeard
I used a 2" hole saw with a 1/4" pilot bit. This creates disks about 1-3/4" with a 1/4" hole in the center. I cut two of them from 1/16" thick material such as the plexi-glass. In one disk I drill (6 ) 3/16" holes around the edge to hold the disk magnets measuring 3/16" wide and 1/16" thick. (#D31-N42 from K&J Magnetics) I epoxy the disks together and insert the magnets (all polarized the same way) into the disk with the holes. I then take a small triangle file to the center hole and make the four corners of the square hole. The wheel is mounted magnet side to the reed switch.

However this is a wheel I designed for a reed switch and have no idea about it working with your three wire sensor.
I was wondering if you had a square punch to do the center hole but a file will get the job done without looking too messy. As for your wheel, the same wheel is used on both the reed switch and hall switch in my actuators so your wheel ought to work fine with either switch. I still have a reed switch in one actuator and I'm trying to decide if I want to change it out for a hall sensor or just change out the magnet with more poles in order to increase the pulse count. That's why I've been searching for just the magnet. I'm not sure if a hall sensor will give better pointing accuracy or if it'll last longer than a reed. Not to mention having to supply it with 5VDC.
M
As I said before, that Hall Effect sensor you have doesn't operate like a hall effect sensor. It makes me think it's an adapter circuit with a reed switch trigger in it. Made for old movers that couldn't use a reed switch. But I don't have one of them to examine so I really don't know what's up with that.
But when I made my magnet wheel I re-did the reed switch too. I doubt that if you made a wheel identical to mine it would operate any of your sensors.
Trust
With a optical sensor , the making of a pulswheel is far more easier (I think)
This one was made for a AHM36 H2H rotor to let it work for Usals .
WhiteBeard
As I said before, that Hall Effect sensor you have doesn't operate like a hall effect sensor. It makes me think it's an adapter circuit with a reed switch trigger in it. Made for old movers that couldn't use a reed switch. But I don't have one of them to examine so I really don't know what's up with that.
False advertising? I'm not going to open one up to see what's inside although there wasn't any warranty implied.
Bruce
Supporting Founder Lifetime Supporter
Last reply · posted in Internet Television (IPTV) Discussion Forum
I was reading this article


That said this-
Last summer, for the first time, streaming services like Netflix and Amazon Prime claimed the largest share of the television viewing audience, surpassing both cable and broadcast TV. Streaming captured 34.8 percent of July viewers, according to Nielsen data, compared to 34.4 percent for cable and 21.6 percent for broadcast.

And then, sometime in the second half of 2022, cord-cutters became the majority. The share of cable and satellite television subscribers dipped to 48 percent, according to a report from Samba TV, a television technology company.


Now I do not consider those with YTTV and the likes, Cord Cutters, but they still do not have Traditional Cable/Satellite delivered Live TV, so I decided to do the math.

There are, now, 129 Million Households in the United States.

In 2015, there were 100 Million Cable/Sat Subscribers , no streaming Live TV Service.

Today, there are 66 Million Live TV subscribers, including Cable, Satellite and Streaming.

Roughly, Streaming Live TV has 14 Million subs including all of them.

So that means, Cable/Satellite now has, roughly, 51 Million Households

So in just 8 years, lost 49% of their subscribers and by the end of this year, expected sub count to be, roughly, 45 million households.

That means a total loss of 55% since 2015 at the end of 2023.

But out of 129 Million households, 45 million will mean only 35% will get Cable/Satellite Delivered Live TV by the end of 2023.

Imagine what 2024 will be like.
820 Replies · 69348 views
  • Wow
Reactions: MikeD-C05
b4pjoe
There are contracts on streaming services. If you want a cheaper price you have to sign up for a year and pay the full amount. If you want to cancel you can but you don't get any money back. They don't cancel it until that yearly subscription ends. So if you don't want a contract you have to pay the higher monthly fee. But at least now you have a choice which way to go.
Jimbo
There are contracts on streaming services. If you want a cheaper price you have to sign up for a year and pay the full amount. If you want to cancel you can but you don't get any money back. They don't cancel it until that yearly subscription ends. So if you don't want a contract you have to pay the higher monthly fee. But at least now you have a choice which way to go.
I wish all Streaming services offered Yearly deals.
b4pjoe
I wish all Streaming services offered Yearly deals.
Yeah if you know you are going to be there for that long you can definitely save some money. Disney+ and Hulu both have yearly deals but not if you bundle them. You have to just go monthly when you bundle them.
Jimbo
Yeah if you know you are going to be there for that long you can definitely save some money. Disney+ and Hulu both have yearly deals but not if you bundle them. You have to just go monthly when you bundle them.
I have 2 that I know I'll do for sure year round, thats Netflix and Paramount Plus ...
The others I use fron time to time, although Hulu I find myself using this past year (I have it in a Bundle with ESPN and Disney) Surprisingly, I find ESPN almost useless.
Bruce
Comcast Corporation, one of the largest telecommunications and media conglomerates in the United States, has shed more than 13 million pay-TV subscribers since reaching its zenith in the late 2000s. The company's video subscriber base, which includes traditional cable television services, stood at approximately 24.2 million customers toward the end of 2008. By the close of the first quarter of 2026, that figure had plummeted to roughly10.95 million, representing a loss of about 13.25 million subscribers, or more than half of its historical peak.

  • Wow
Reactions: ncted
dishdude
Comcast Corporation, one of the largest telecommunications and media conglomerates in the United States, has shed more than 13 million pay-TV subscribers since reaching its zenith in the late 2000s. The company's video subscriber base, which includes traditional cable television services, stood at approximately 24.2 million customers toward the end of 2008. By the close of the first quarter of 2026, that figure had plummeted to roughly10.95 million, representing a loss of about 13.25 million subscribers, or more than half of its historical peak.


Couldn't happen to a nicer company!
Bruce
The average monthly cost of cable television in the United States has climbed to $147, marking a significant increase that reflects broader trends in media consumption and rising operational expenses for providers. This figure represents the baseline expense for standard television packages across major cable operators, excluding additional fees for premium channels, equipment rentals, or taxes that often push household bills even higher.

This is without Broadband services ( bundled), also, paying a lot more for a lot less new scripted content and now….sports.

T
Anyone know how Canadians are doing with cord cutting? I would think there could be added incentive simply in that Canadian cable/sat has been heavily regulated to exclude much of US content in order to promote home content. Streaming would seem to cut through any of that, presuming there aren't restrictions on that as well. Or maybe US streamers won't sell there?
T
Pub Member / Supporter
Last reply · posted in DISH Network Support Forum
Wasn't there a law passed a long time back mandating service providers level the sound from one ch. to the next? Or was that just for within any single given ch., and not letting commercials be boosted? Regardless it's a pain on DiSH with some ch's way louder than others, and having to jockey the sound up & down. Is there some fix? Can some TVs compensate for this?
11 Replies · 685 views
  • Like
Reactions: LQQK
T
depend on how you tv and box is setup? as both have "audio" leveling

for me if I have audio leveling on hopper enabled DD is lower then Stereo if i turn off on h3 turn on tv it the reverse. Almost ALL streaming channels much lower volume level then statalite channels.

Either way one my pet peaves is that even channel seem to have it own "audio level" and so to commericals and none of the actual audio leveling functions actual fix this and never have. would be nice if every channel dish/dtv/fios etc all made volume level defualt to same dB so atlest all channel where consistent volume probably wont help commercials though.

To my knowledge no TV has ever had audio leveling function that actual fixed that all it really does it either lower or raise the volume
Former member 208119
depend on how you tv and box is setup? as both have "audio" leveling

for me if I have audio leveling on hopper enabled DD is lower then Stereo if i turn off on h3 turn on tv it the reverse. Almost ALL streaming channels much lower volume level then statalite channels.

Either way one my pet peaves is that even channel seem to have it own "audio level" and so to commericals and none of the actual audio leveling functions actual fix this and never have. would be nice if every channel dish/dtv/fios etc all made volume level defualt to same dB so atlest all channel where consistent volume probably wont help commercials though.

To my knowledge no TV has ever had audio leveling function that actual fixed that all it really does it either lower or raise the volume
maybe he should post his gear so we could look into it 🤔.. t.v. soundbars AVR whatever he's running.. our home theater has volume leveling but so does our soundbar in the bedroom:)
  • Like
Reactions: charlesrshell
T
maybe he should post his gear so we could look into it 🤔.. t.v. soundbars AVR whatever he's running.. our home theater has volume leveling but so does our soundbar in the bedroom:)

Most stuff has all this volume leveling, almost all them dont work the way should or advertised as. maybe "ai" versions of volume level will work closer to way we would like to which make all channels and inputs same defualt sound level, including commercials

There is reason my entire mp3/audio music collection on my pc was changed to have same defualt "dB" for all files via something like MP3Gain so there all same defualt volume level and there for I never have to play around with my volume. I know Winamp could change dB defualts but never worked as good as just manual changing all the audio/mp3/music collection files to just be all the same
  • Like
Reactions: charlesrshell
T
But doesn't music require a lot of dynamic range? At least classical & the like? So there has to be allowance for some highs without attenuation, and some lows without boosting. It seems there needs to be some kind of a universal median level that all sources can register to, that still allows for both soft and loud intermittently. My dad always had westerns on and the gunshots really rang out
  • Like
Reactions: charlesrshell
S
That's a fundamental issue with volume levels - it's not just that people want some "level" but that the material itself can demand (or at least so says the creator) a wide dynamic range or a smaller one. ie: do you boost the typical conversations upward and use most of your range just for voices? Or do you leave room for the explosions and jet engines. Creators and viewer/listeners all vary in their priorities, and most volume-leveling products are trying to do things in real time so they have very little context to work with. Even when using a tool that reads a whole file and displays a peak volume, you can wonder how often such a volume occurs and then you can disagree on how important it is for something like an explosion to have any clipping/distortion.

I think the OP refers to the Commercial Advertisement Loudness Mitigation Act, AKA the CALM act. But as the name suggests, I think it only has to do with commercials and not different sources.

By the way, if you watch westerns with realistic gunshot sound levels, I recommend hearing protection. :)
T
I will say this on PC it worse one game is one volume level by defualt another is super quiet and another deafening loud, and volume leveling dont equalize it. The dynamic range isnt the problem the defualt volume is not same from channel to channel, commercial to commercial game to game.

To mean volume leveling is defeat volume level from source to source channel to channel, commercial to commercial, game to game.

Default volume level of 89.9 dB across the board fixes that tv providers can easily do this from there end and mandate commercial creators follow it, but it wont ever happen

Maybe volume leveling means somthing else to other people
  • Like
Reactions: charlesrshell
T
This only if anything seems to be worsening on DiSH. Ch. 215 is a prime example. It's typically much louder than other ch's, and today I notice it even contradicting itself, shifting drastically up and down inexplicably over periods of several minutes. Oddly, the quietest periods have come during commercials...
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in The Chit Chat Club
Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne


Get it?


An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
67108 Replies · 2662318 views
  • Like
Reactions: c-spand
sdfntx
Right on Time - Brandi Carlile
gms49ers
Time Stand Still - Rush
  • Like
Reactions: long_time_DNC
Bobby
I Can't Help It (If I'm Still In Love With You) - B.J. Thomas
  • Like
Reactions: sdfntx
long_time_DNC
Help Is On Its Way - Little River Band
sdfntx
Little Band of Gold - Sonny James
Bobby
Supporting Founder Lifetime Supporter
Last reply · posted in DISH Network Support Forum
This is a thread that will keep you apprised of 4K events that will be showing on Dish channel 540. Keep looking here for information.

As of today, 9-27-17, there are no scheduled events posted for the next 2 weeks. That is subject to change on a daily basis.
699 Replies · 164669 views
Bobby
WC, Canada vs Bosnia and Herzegovina, Friday 6-12, 12PM PDT, Channel 540-01.
WC, USA vs Paraguay, Friday 6-12, 6PM PDT, Channel 540-01.
  • Like
Reactions: charlesrshell
Bobby
WC, Qatar vs Switzerland, Saturday 6-13, 12PM PDT, Channel 540-01.
WC, Brazil vs Morocco, Saturday 6-13, 3PM PDT, Channel 540-01.
WC, Haiti vs Scotland, Saturday 6-13, 6PM PDT, Channel 540-01.
WC, Australia vs Türkiye, Saturday 6-13, 9PM PDT, Channel 540-02
  • Like
Reactions: charlesrshell
Bobby
WC, Germany vs Curaçao, Sunday 6-14, 10AM PDT, Channel 540-01.
WC, Netherlands vs Japan, Sunday 6-14, 1PM PDT, Channel 540-01.
WC, Côte d'Ivoire vs Equador, Sunday 6-14, 4PM PDT, Channel 540-02.
WC, Sweden vs Tunisia, Sunday 6-14, 7PM PDT, Channel 540-02.
  • Like
Reactions: charlesrshell
Bobby
WC, Belgium vs Egypt, Monday 6-15, 12PM PDT, Channel 540-01.
WC, Saudi Arabia vs Uruguay, Monday 6-15, 3PM PDT, Channel 540-02.
WC, Iran vs New Zealand, Monday 6-15, 6PM PDT, Channel 540-02.
Bobby
WC, France vs Senegal, Tuesday 6-16, 12PM PDT, Channel 540-01.
WC, Iraq vs Norway, Tuesday 6-16, 3PM PDT, Channel 540-01.
WC, Argentina vs Algeria, Tuesday 6-16, 6PM PDT, Channel 540-01.
WC, Austria vs Jordan, Tuesda6 6-16, 9PM PDT, Channel 540-02.
Gary Toma
Staff member Pub Member / Supporter Cutting Edge
Last reply · posted in DIRECTV Technical Resources Forum
The TPN Map Excel Presents all DIRECTV Channels:
National (50-States or wide/NAT+PR beams)
Local (Local-Into-Local or narrow/Spot beams)
Additional tabs provide:​
OTA the (Over-The-Air) Database
VOD (Video On_Demand) Records
Offline Records
Engr Records
Net Decoder a graphic presentation of all satellites and transponders
Domestic Satellites
@99W...... D11, D14
@101W.... D9S, D16
@103W.... D10, D12, D15
@110W.... D5
@119W.... D8​



See also

Understanding the TPN Map

Making Sense of the TPN Map Display Conventions
1971 Replies · 910655 views
K
604 Pursuit HD is testing

Women's US Open Out, Men's US Open and World Cup in

The World Cup Bracket on 205-6 and 407-2 will be repurposing CINEHD 154
(There will be a mix on one of the 205s and 407-1)

The Vegas specific slate for KTNV is repurposing Dispute Slide 1 Test 9109
lordodogg
604 Pursuit HD is testing
Interesting. I remember that being HD-only for a bit a long time ago and then it was back to SD-only.
  • Like
Reactions: Gary Toma
lordodogg
Interesting. I remember that being HD-only for a bit a long time ago and then it was back to SD-only.
looking at the old maps, that was from March 2017 to June 2019.
lordodogg
Starz is apparently dropping all of the west coast feeds of their networks tomorrow. FiOS has already dropped most of the ones they carried and I imagine DirecTV would be affected with STZw on 526 and SENw on 536.
  • Wow
Reactions: dtv757
lordodogg
seems to actually only be affecting their sister channels, not the main channels
K
Starz, Starz Encore and Starz Encore Westerns are keeping their west coast feeds. The rest of the Starz, Starz Encore and Plex channels will only have East coast feeds
zippyfrog
Pub Member / Supporter Lifetime Supporter
Last reply · posted in DISH Network Support Forum
Did anyone have a price increase today on their equipment? I own my VIP211k's, and they have been $5.00. My bill that I received last week shows the "add-ons" as being $5.00. However, I just logged into my Dish account, and my "add-ons" are now $10.00. Did the additional receivers go up by $5.00 recently?

As I mentioned, my last bill shows $5.00 and under the notes, nothing is mentioned about a price increase.
10 Replies · 145 views
T
Does cable charge box rent?
R
Does cable charge box rent?
The cable company I was with years ago did charge $9.99 for a receiver.

RJ T.
From Illinois
  • Like
Reactions: charlesrshell
R
Did anyone have a price increase today on their equipment? I own my VIP211k's, and they have been $5.00. My bill that I received last week shows the "add-ons" as being $5.00. However, I just logged into my Dish account, and my "add-ons" are now $10.00. Did the additional receivers go up by $5.00 recently?

As I mentioned, my last bill shows $5.00 and under the notes, nothing is mentioned about a price increase.
I went to try to add the Heartland channel as dummy to see what it would do for me as I own my receiver and have DISH Outdoors and this is what mine shows. (Note however I had to take the 2nd receiver I told you I added the other day off because I was told you can only have 1 receiver when you have a one outlet on the Dish Playmaker and was having issues with the 2nd receiver and I didn't know that and that was done yesterday as well so I am back to one receiver.)

Let's upgrade your package.

Your monthly bill will increase by $6.00 per month.

Breakdown

June 11, 2026 - July 11, 2026
You are changing your programming in the middle of the bill cycle. The bill shown below is your bill for next month including prorations and credits. Your following bill will return to the fixed rate. This bill will take effect from now until July 11, 2026.
Monthly Services
$86.99

Flex Pack
$72.99
Local Channels
$14.00
Add-Ons
$68.98

National Action Pack
$12.00
Regional Action Pack
$12.00
News Pack
$10.00
Paramount+ with Showtime
$10.00
Drama and Classics Pack
$6.00
Heartland Pack
$6.00
Starz Encore Movies
$6.00
On DISH Magazine
$4.99
Starz 2 Mo ($11)
$1.99
Prorated Charges
$7.93

Heartland Pack Jun 11 - Jul 20
$7.93
Order Total
$7.93

Prorated Total
$7.93
Due Today
$7.93

Transition Bill Total
$156.10
Proposed Changes

Your monthly bill will increase by $6.00 per month
Monthly Services
$86.99
Add-Ons
$68.98
FCC Regulatory Surcharge
$0.13
Taxes & Surcharges
$0.00

Monthly Total
$156.10
Prorated Total
$7.93
Order Total
$7.93

Due Today
$7.93

Sounds like an issue with DISH Billing

RJ T.
From Illinois

  • Like
Reactions: charlesrshell
zippyfrog
I asked again, and the rep I talked to said it is a glitch and that "Access for TV" shouldn't be there - the rep pulled up my future month bills and that charge isn't on it. So I am not going to worry about it right now, but it will be interesting to see when the price changes happen later this year. Will this line item show up? The fact that it is a specific item that is different from anything makes me think it is more than a glitch. But we shall see.
R
I asked again, and the rep I talked to said it is a glitch and that "Access for TV" shouldn't be there - the rep pulled up my future month bills and that charge isn't on it. So I am not going to worry about it right now, but it will be interesting to see when the price changes happen later this year. Will this line item show up? The fact that it is a specific item that is different from anything makes me think it is more than a glitch. But we shall see.
I am hoping they don't add this down the road. Things are expensive the way it is now. Even DIRECTV allows the first receiver free. This would go against DISH and DISH is already loosing subscribers I wouldn't think they would do these kind of tricks but you never know. Always look at your bills for unknow charges. I heard horror stories of people getting charged for things they didn't know were there.

RJ T.
From Illinois
zippyfrog
Pub Member / Supporter Lifetime Supporter
· posted in The Phone & Tablet Zone
I feel like this was discussed in another thread, but I can't find it. I have T-Mobile and my last iPhone upgrade was in 2020. I want to get a new iPhone, but what is the best way to go about doing it? Should I order the iPhone from T-Mobile directly, or should I buy from the Apple Store? I feel like there are pros/cons to each option.
0 Replies · 8 views
T
Last reply · posted in DISH Network Support Forum
Hello everyone, new guy here. I'm trying to solve problem I'm having with Dish bonus view channels. When I'm watching the bonus view channels then I switch back to regular dish channels, after few minutes the screen flips to black and after 30 seconds flips back to regular channels and continues to flip back and forth until I turn off TV. After I wait 30 minutes and turn back on , I can use regular channels again. So, its after I switch from bonus view channels to regular dish channels the problem starts. Been trying to fix this for a month, but no luck
Here what I've done.
i contacted Dish support and they sent me a new Joey3, but no help. Switched to a different HDMI input on TV, no help. Used different HDMI cable , no help. Used different electrical wall plug, no help.
Finally got a Dish tech to check it. He ran all systems check and was OK. Finally he brought in a small TV and plugged in the HDMI out from the Joey to the small TV. He could not get the problem to occur on his small TV, so the new Joey was working OK. So, then the problem must be myTV. He made some phone calls and came back with the answer that there must be a problem with the analog to digital switch in my TV. Has anyone ever heard of a problem like this, or is it time to be looking for a new TV? My tv LG OLED65C8PUA. TV has been trouble free til now. Thanks
2 Replies · 44 views
HipKat
Hello everyone, new guy here. I'm trying to solve problem I'm having with Dish bonus view channels. When I'm watching the bonus view channels then I switch back to regular dish channels, after few minutes the screen flips to black and after 30 seconds flips back to regular channels and continues to flip back and forth until I turn off TV. After I wait 30 minutes and turn back on , I can use regular channels again. So, its after I switch from bonus view channels to regular dish channels the problem starts. Been trying to fix this for a month, but no luck
Here what I've done.
i contacted Dish support and they sent me a new Joey3, but no help. Switched to a different HDMI input on TV, no help. Used different HDMI cable , no help. Used different electrical wall plug, no help.
Finally got a Dish tech to check it. He ran all systems check and was OK. Finally he brought in a small TV and plugged in the HDMI out from the Joey to the small TV. He could not get the problem to occur on his small TV, so the new Joey was working OK. So, then the problem must be myTV. He made some phone calls and came back with the answer that there must be a problem with the analog to digital switch in my TV. Has anyone ever heard of a problem like this, or is it time to be looking for a new TV? My tv LG OLED65C8PUA. TV has been trouble free til now. Thanks
First off, great TV. I'm torn between the 77C5 or the 77G5.
It sounds like the handshake between the Receiver and the TV is having a problem. Are you using the free cable that came with the Joey or a higher speed HDMI cable?? That's the f irst place I'd look
R
Hello everyone, new guy here. I'm trying to solve problem I'm having with Dish bonus view channels. When I'm watching the bonus view channels then I switch back to regular dish channels, after few minutes the screen flips to black and after 30 seconds flips back to regular channels and continues to flip back and forth until I turn off TV. After I wait 30 minutes and turn back on , I can use regular channels again. So, its after I switch from bonus view channels to regular dish channels the problem starts. Been trying to fix this for a month, but no luck
Here what I've done.
i contacted Dish support and they sent me a new Joey3, but no help. Switched to a different HDMI input on TV, no help. Used different HDMI cable , no help. Used different electrical wall plug, no help.
Finally got a Dish tech to check it. He ran all systems check and was OK. Finally he brought in a small TV and plugged in the HDMI out from the Joey to the small TV. He could not get the problem to occur on his small TV, so the new Joey was working OK. So, then the problem must be myTV. He made some phone calls and came back with the answer that there must be a problem with the analog to digital switch in my TV. Has anyone ever heard of a problem like this, or is it time to be looking for a new TV? My tv LG OLED65C8PUA. TV has been trouble free til now. Thanks
First off, The analog to digital switch, also known as the digital television transition, is the process of converting older analog television broadcasting technology to digital broadcasting. It's used through coaxial cable for the an antenna during the mandatory switch from Analog to Digital on June 12, 2009. You either had to get a converter for your analog (Tube TV) or use a converter box that has the analog or digital tuner or an HDTV which your is and has the tuner built in. Your TV is HD and using an HDMI Cable and nothing is connected by coaxial cable so this wouldn't apply.

In my theory it probably means a new TV. I had a TV go out on my switching between the Smart Screen from the HDMI inputs before because they went faulty. Sometimes electrical surges can cause this. If you have an older home or rent an older home or apartment sometimes the electrical outlets are not grounded and these days HDTV's need a ground which can cause them to malfunction and go bad quicker. Never plug it directly in an outlet. It will damage the TV.

Hope I could be of some assistance.

RJ T.
From Illinois
  • Like
Reactions: charlesrshell
Y
Pub Member / Supporter
· posted in The Sports Section
Mexico takes on South Africa to open the World Cup Final (it is called the Final... this just isn't the World Cup Final... Final). The tournament has been plagued with rife malfeasance as FIFA has been committing all sorts of fraud with the ticket sales. Hotel rooms have gone unfilled as the prices to attend a game and stay somewhere are through the roof. I swear this is impacting Mansfield, OH hotel rates which are higher than average for the Indycar race. And there is a broadening VAR presence which will ruin things as nothing worse now when scoring a goal and knowing you can't quite celebrate yet as they check to see if a player was offside by a pixel a half-hour ago.

The Group Stage used to mean something, but now 32 of the 48... yeah, 48 teams are going to the Knockout Round. Getting into the Knockout Round used to be a big deal, even for the US. But now... if you don't lose all of your group stage games, you get to move on. Oi! And this is avoiding all the political stuff!

I have never been so unexcited for a World Cup before. Every game used to matter. But FIFA be darned if they don't try to squeeze out every dime they can out of the players, refs, and fans.
0 Replies · 12 views