Social Feed

W
Last reply · posted in DISH Network Support Forum
Hello everyone. I'm posting again about my Dish issue. I'm still having problems with signal loss. I'm getting the "Complete Signal Loss" screen, Signal Code: 11-12-11. But there's absolutely nothing obstructing the signal of my dish. I have unplugged the receiver for 10 seconds and still nothing is changing. I recently moved into a house where the previous owners were using DirectTV. I brought my Dish with me from my old house and mounted it to the pole (using the existing coax). I replaced the existing splitters with barrel connectors (Just using one receiver). The dish is set at the proper azimuth, elevation, and skew angle based on zip code, and still can't figure out what the problem could be. I have a little bit of experience setting up Dish on my RV but can't figure this one out. Thanks in advance for more tips.
25 Replies · 7625 views
W
Sam_gordon, I meant I took the receiver outside, with a little TV, and plugged the short coax coming off the pole directly into the receiver. Someone on this thread suggested trying it. Yes I turned the dish and there is absolutely no signal no matter how I turn the dish.
My plug-in looks like the bottom picture you attached.
S
Sam_gordon, I meant I took the receiver outside, with a little TV, and plugged the short coax coming off the pole directly into the receiver. Someone on this thread suggested trying it. Yes I turned the dish and there is absolutely no signal no matter how I turn the dish.
My plug-in looks like the bottom picture you attached.
Just clarifying... were you on the "point dish" screen when you were moving the dish, or were you just on a channel and waiting for it to detect a signal? I'm not trying to be insulting, but when troubleshooting, if I (we) assume you've done a step correctly, we can miss what the problem is. And were you able to confirm that you had voltage at the LNB end of the cable?


If you want to continue trying to solve this yourself, here's what I would do... First, I'm going to assume your elevation is supposed to be 40 and azimuth 180 (just sample numbers)...
1) Hook up the receiver and little TV as you did before.
2) Go through the menu to the "point signal" screen.
2.5) Do a "Check Switch".
3) Tilt the elevation to 38 degrees and aim at 90 degrees.
4) Pan clockwise slowly (~2 degrees every second) until you're at 270 degrees while watching the signal strength meter. If you get even a blip of signal, stop, move dish left right/up/down to maximize that signal. If you don't get any signal, continue to step 5.
5) Raise the elevation to 39 degrees, and repeat step 4, but in the opposite direction.
6) Continue to raise the elevation by 1 degree and pan across the sky. Do this until you get to 44 degrees of elevation

ETA: I forgot to address the plug.
Either get a replacement cord (I don't remember if the cord is meant to be separated from the receiver), call Dish, or, if you own the receiver, you can cut that end of the cord off, go to your favorite store and pick up and install a new end.
1608646555359.png

If you can't handle putting this onto the end of the cable, you shouldn't even bother trying to troubleshoot your receiver.
  • Like
Reactions: the mack
W
Just clarifying... were you on the "point dish" screen when you were moving the dish, or were you just on a channel and waiting for it to detect a signal? I'm not trying to be insulting, but when troubleshooting, if I (we) assume you've done a step correctly, we can miss what the problem is. And were you able to confirm that you had voltage at the LNB end of the cable?


If you want to continue trying to solve this yourself, here's what I would do... First, I'm going to assume your elevation is supposed to be 40 and azimuth 180 (just sample numbers)...
1) Hook up the receiver and little TV as you did before.
2) Go through the menu to the "point signal" screen.
2.5) Do a "Check Switch".
3) Tilt the elevation to 38 degrees and aim at 90 degrees.
4) Pan clockwise slowly (~2 degrees every second) until you're at 270 degrees while watching the signal strength meter. If you get even a blip of signal, stop, move dish left right/up/down to maximize that signal. If you don't get any signal, continue to step 5.
5) Raise the elevation to 39 degrees, and repeat step 4, but in the opposite direction.
6) Continue to raise the elevation by 1 degree and pan across the sky. Do this until you get to 44 degrees of elevation

ETA: I forgot to address the plug.
Either get a replacement cord (I don't remember if the cord is meant to be separated from the receiver), call Dish, or, if you own the receiver, you can cut that end of the cord off, go to your favorite store and pick up and install a new end.
View attachment 149453
If you can't handle putting this onto the end of the cable, you shouldn't even bother trying to troubleshoot your receiver.
Yes I was on the "Point Dish" page when turning the dish by hand. I have a little experience setting up dishes since I used to use a Dish in my RV. I haven't been able to test voltage at the LNB since I don't have the proper meter. I wanted to try a couple more things (which I have done now) before calling for Dish's help. It's obviously a receiver issue and/or LNB coax needing replaced. Thanks for all the info, I may still use it. I appreciate all the help. I'm probably going to contact Dish now.
J
Yes I was on the "Point Dish" page when turning the dish by hand. I have a little experience setting up dishes since I used to use a Dish in my RV. I haven't been able to test voltage at the LNB since I don't have the proper meter. I wanted to try a couple more things (which I have done now) before calling for Dish's help. It's obviously a receiver issue and/or LNB coax needing replaced. Thanks for all the info, I may still use it. I appreciate all the help. I'm probably going to contact Dish now.
I would suggest you stop everything until you verify you have voltage going to the LNB. Nothing is going to work until you have voltage. I would not do a 'check switch', until you do as I think that doing so will wipe out the necessary info for the receiver to have a chance to connect. Just go to the check switch screen and see if it still shown all 3 LNB's. If it shown no connections, take the receiver to a known good dish and hook it up and run a check switch. Then, once it shows all 3 LNB's, you can try it on your system.
pattykay
I would suggest you stop everything until you verify you have voltage going to the LNB. Nothing is going to work until you have voltage. I would not do a 'check switch', until you do as I think that doing so will wipe out the necessary info for the receiver to have a chance to connect. Just go to the check switch screen and see if it still shown all 3 LNB's. If it shown no connections, take the receiver to a known good dish and hook it up and run a check switch. Then, once it shows all 3 LNB's, you can try it on your system.
The problem with that is that there are different types of LNB's, even for aiming at the exact same satellites. For example, there are 1000.4 DPP LNB's, 1000.2 DPP LNB's, 1000.2 DPH LNB's, and even 1000.2 DPH "Slimline" LNB's, all for aiming at Western Arc. If the receiver is looking for the wrong type of LNB, then it is not going to find the signal. Running the Check Switch with nothing connected is entirely the point: to clear out any incorrect info that may be in the receiver. However, that is also why I said to make sure the dish is aimed as well as possible toward the correct coordinates before doing the Check Switch again, to give the receiver the best chance of actually finding a usable signal with the correct info, before trying to peak the signal strength.
Jim5506
Test the ground and center lug of the cable with your tongue, 18 volts will give you a buzz, but it only hurts for a little while.
pattykay
Test the ground and center lug of the cable with your tongue, 18 volts will give you a buzz, but it only hurts for a little while.
Just don't try this in freezing cold weather. ;)
charlesrshell
Test the ground and center lug of the cable with your tongue, 18 volts will give you a buzz, but it only hurts for a little while.
Reminds me when I was a kid around 5 my dad was cranking on a lawnmower engine that wouldn't start. He had me touch the spark plug tip and he cranked her. I came a few feet off the ground. Spark was good! My mom was a little upset.
  • Wow
Reactions: TheKrell
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in The Chit Chat Club
Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne


Get it?


An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
68631 Replies · 2678978 views
  • Like
Reactions: c-spand
H
PEOPLE Are Strange-The Doors
harshness
Still Loving You - Scorpions
Bobby
PEOPLE Are Strange-The Doors

You're Still A Young Man - Tower Of Power
No Match, back to:
People Are Strange - The Doors




Isn't Life Strange - The Moody Blues
FTA4PA
Strange Days - Nazareth
  • Like
Reactions: dishstaller
gms49ers
Dancing Days - Led Zeppelin
dishstaller
Dancing in the Street - Van Halen
TWiT Tech Podcast Network
· posted in TWiT Tech Podcast Network
0 Replies · 5 views
TRG
TRG
Pub Member / Supporter
Last reply · posted in Local Radio Discussion
20 Replies · 583 views
dishdude
It's probably been 2 decades since I've listened to an AM radio station. Very rarely listen to FM any more.
  • Like
Reactions: reubenray and Jimbo
Jimbo
I am 1 that wants the AM to Stay ....
That said, since '08 I have had Sat radio available to me ... I think I have turned on AM 3 or 4 times, just to see if its still there.

Fwiw, if theres a Major disaster or bad weather or whatever, the chances of me finding out about it by going to the AM side of the radio is SLIM and None.
Even FM, I haven't really had on since '13ish, I may turn it on from time to time, just to see if its still there.
harshness
Fwiw, if theres a Major disaster or bad weather or whatever, the chances of me finding out about it by going to the AM side of the radio is SLIM and None.
Automation has seen to that. You can't get evening drive traffic reports where I live, much less disaster reports.
dishstaller
Very rarely listen to FM any more
That goes for a lot of people. I've been advertising on radio for more than a decade now and am very familiar with this subject. While it is still a valuable tool, it has far less impact than it did just a few years ago. The best reaction I get is from a local Country music station....they play a mix of older and newer music and have a very big footprint.
  • Like
Reactions: Mr Tony
Jimbo
That goes for a lot of people. I've been advertising on radio for more than a decade now and am very familiar with this subject. While it is still a valuable tool, it has far less impact than it did just a few years ago. The best reaction I get is from a local Country music station....they play a mix of older and newer music and have a very big footprint.
Do you do any Ad's on Satellite ?

If Not, why not, because it's not Local ?
dishstaller
Do you do any Ad's on Satellite ?

If Not, why not, because it's not Local ?
No, just regular FM stations. One is the country station I mentioned and the other is a Talk Radio station which used to get fantastic results but honestly, since the death of Rush Limbaugh, talk radio just doesn't do as well. There were two guys who had an early morning show which was hugely popular here in the southeast but one of them retired a couple years ago and the show just doesn't garner the same numbers as it used to.
TheForce
Supporting Founder Pub Member / Supporter
Last reply · posted in The Phone & Tablet Zone
Apple Fall Hardware Event takes place today, September 9, 2026, at 10:00 a.m. PT / 1:00 p.m. ET. It marks the debut of new CEO John Ternus and the expected reveal of Apple's first foldable phone.
135 Replies · 1640 views
comfortably_numb
Can't remember if I've posted this yet..


View: https://www.youtube.com/watch?v=nfL5seXJyWU
  • Haha
Reactions: slow_poke_pete
Foxbat
IFixIt has published their Teardown and they had some positive things to say about the iPhone Duo. It still showed some dust ingress into the hinge assembly but seemed otherwise well-sealed.
​

But with a considerable number of reports of the main screen dying with similar failures, AppleCare+ should be a no-brainer for this phone.
S

most carriers do. that's why they send updates that slow phones down!! i buy unlocked phones no effect to me
S
IFixIt has published their Teardown and they had some positive things to say about the iPhone Duo. It still showed some dust ingress into the hinge assembly but seemed otherwise well-sealed.
​

But with a considerable number of reports of the main screen dying with similar failures, AppleCare+ should be a no-brainer for this phone.

hope you have apple care a screen job is 1000.00 :oops:. can we say over priced garbage!!!
harshness
Gone are the days when Apple "perfects" what debuted years earlier on an Android phone.
comfortably_numb
Gone are the days when Apple "perfects" what debuted years earlier on an Android phone.

Or better yet, innovate something "completely revolutionary!"
SkyWatcher57
Pub Member / Supporter
Last reply · posted in Free To Air (FTA) Discussion
Hello folks, well my luck ran out last week with a nasty thunderstorm and after 39 years here, finally took a hit. Now, the FTA receivers I had for some years worked great until now. Recently picked up a fairly cheap receiver, online, KOQIT and seems to be good, but for the life of me, I cannot get the HDMI output to work with 3 of my Samsung monitors. I can hook it up to my Samsung TV and its HDMI input and it works fine. The 2 receivers I lost also worked fine with them, so am I going crazy? anyone have come across this or have any suggestions? And, since this is a somewhat cheap unit but works, what is everyone out there using for receivers these days? without breaking the bank? I enjoy watching FTA TV, so I will invest more if needed, what is a really good, detailed unit these days. I'm so use to watching a few of them HD channels. Right now I'm down to composite hookups, yuck! Any help or info would be greatly appreciated. Thanks Frank :rolleyes:
47 Replies · 1293 views
(((Garyd)))
Hello folks, well my luck ran out last week with a nasty thunderstorm and after 39 years here, finally took a hit. Now, the FTA receivers I had for some years worked great until now. Recently picked up a fairly cheap receiver, online, KOQIT and seems to be good, but for the life of me, I cannot get the HDMI output to work with 3 of my Samsung monitors. I can hook it up to my Samsung TV and its HDMI input and it works fine. The 2 receivers I lost also worked fine with them, so am I going crazy? anyone have come across this or have any suggestions? And, since this is a somewhat cheap unit but works, what is everyone out there using for receivers these days? without breaking the bank? I enjoy watching FTA TV, so I will invest more if needed, what is a really good, detailed unit these days. I'm so use to watching a few of them HD channels. Right now I'm down to composite hookups, yuck! Any help or info would be greatly appreciated. Thanks Frank :rolleyes:
Take the cover off, show me pics of the board of the bad one and also the bottom of the board. I'm an old hardware electronics tech plus a satellite dealer; I fixed a lot of FTA and regular receivers. I may be able to fix it for you. And yes, they got hit by lightning; it's best to email me the pics at diamondsatellite@snet.net or call me at 203-232-8888. I give you a 50-50 chance of fixing it; I do have spare parts. my phone is a fliptop phone
Gary
  • Like
Reactions: navychop
S
Hello folks, well my luck ran out last week with a nasty thunderstorm and after 39 years here, finally took a hit. Now, the FTA receivers I had for some years worked great until now. Recently picked up a fairly cheap receiver, online, KOQIT and seems to be good, but for the life of me, I cannot get the HDMI output to work with 3 of my Samsung monitors. I can hook it up to my Samsung TV and its HDMI input and it works fine. The 2 receivers I lost also worked fine with them, so am I going crazy? anyone have come across this or have any suggestions? And, since this is a somewhat cheap unit but works, what is everyone out there using for receivers these days? without breaking the bank? I enjoy watching FTA TV, so I will invest more if needed, what is a really good, detailed unit these days. I'm so use to watching a few of them HD channels. Right now I'm down to composite hookups, yuck! Any help or info would be greatly appreciated. Thanks Frank :rolleyes:
a good surge protector will help to.
  • Like
Reactions: SkyWatcher57
SkyWatcher57
Take the cover off, show me pics of the board of the bad one and also the bottom of the board. I'm an old hardware electronics tech plus a satellite dealer; I fixed a lot of FTA and regular receivers. I may be able to fix it for you. And yes, they got hit by lightning; it's best to email me the pics at diamondsatellite@snet.net or call me at 203-232-8888. I give you a 50-50 chance of fixing it; I do have spare parts. my phone is a fliptop phone
Gary
Hi Gary, still working on getting you those
Hi Gary, just saw this, ok, I'll grab some pics tomorrow and post them. thx
Still working getting you those pictures, nice weekends means yard work and fall prep, thanks
  • Like
Reactions: (((Garyd)))
k4otl
Anybody know how to add "hidden" audio channels like for 101 W Ku or 105W C band on these recvr's? I've exported the database file but don't have anything that will read or edit it.
cyberham
For 105W C, you scan in the Westwood tp normally. Then select the audio channel you want. Not necessary to manually enter. On 101W, you must manually enter.
k4otl
For 105W C, you scan in the Westwood tp normally. Then select the audio channel you want. Not necessary to manually enter. On 101W, you must manually enter.
Seems like I remember that now, with my V9 I manually entered anyway on 105, easier for me to pick the channel later :)
T
Last reply · posted in Free To Air (FTA) Discussion
IS Amiko MIRA 3 any good ???
Can you recommend the best to cover all bases. NO BEEPS on certain channels 101w (NEWSMAX ,NEWS NATION), a clock that keeps working STEADY for timed recording ,solid unit with good lifespan. My Amiko died AND my Linkbox has NO Favorites Button and BEEPS on many channels. Picking up 105 west with a NEW SHED IN THE Way with 6 foot Cband ..95 percent quality ...unbelievable.
10 Replies · 270 views
T
Have you tried a new power brick on your Amiko?

YOU WERE RIGHT. IT IS WORKING NOW WITH 2X AMPS !!

DAN
primestar31
Have you tried a new power brick on your Amiko?

YOU WERE RIGHT. IT IS WORKING NOW WITH 2X AMPS !!

DAN
That's great!

Many people have all sorts of power bricks laying around. Provided the plug fits, and it's the right polarity and same voltage and the same OR higher amps, why not try another one IF the device you want to try it on doesn't seem to work right.
  • Like
Reactions: cyberham
JFOK
That's great!

Many people have all sorts of power bricks laying around. Provided the plug fits, and it's the right polarity and same voltage and the same OR higher amps, why not try another one IF the device you want to try it on doesn't seem to work right.
primestar31,

Could you explain to me what a power brick is ?
Thanks,

John
primestar31
primestar31,

Could you explain to me what a power brick is ?
Thanks,

John
Some people just call them power supplies (which really isn't a good fit in this case), some call them "wall adapters" but it's an external power supply or AC adapter that converts (AC) from a wall outlet into low-voltage (DC) that an electronic device needs to run.
  • Like
Reactions: JFOK
T
[Give us a summary of what you receive with a 6-footer. I'm very curious.]

Right now on C band getting 105w, a Mexican channel with 95% quality and I am near Detroit! I'm recording a TECHNO MUSIC FESTIVAL today from Mexico ..if you can believe it.....and yes that SHED is partly in the path so I'm puzzled. There are also christian channels on 105w.
cyberham
...Right now on C band getting 105w, a Mexican channel with 95% quality...
105W has some very strong transponders. I received more than four transponders using a 41-inch dish recently. See here.
k4otl
[Give us a summary of what you receive with a 6-footer. I'm very curious.]

Right now on C band getting 105w, a Mexican channel with 95% quality and I am near Detroit! I'm recording a TECHNO MUSIC FESTIVAL today from Mexico ..if you can believe it.....and yes that SHED is partly in the path so I'm puzzled. There are also christian channels on 105w.
The Westwood One Mux on 105W would likely be receivable, has some good music channels on there. It does scan in, but it's more convenient to manually enter the PIDs, check out Lyngsat for the channels: EchoStar 105/SES 11 at 105.0°W - LyngSat

I use a 10 footer (only C-band dish I have), but it's very strong.