Social Feed

Stuart Sweet
Staff member HERE TO HELP YOU! Pub Member / Supporter Cutting Edge
· posted in The Solid Signal Blog
This Wi-Ex YX500 cell booster was all the rage way back in the late '00s. It worked well with the older-style analog cell phones and anything else that used the 1900MHz band that was used for voice back then. AT&T still uses the 1900MHz band, but they more commonly use the 850MHz band for their 5G broadcasts. The data I was able to find suggests that Verizon still uses it too. Today the world has changed and if you're going to boost your signal you need something that not only covers the 1900MHz band, but the four other bands most commonly used by voice and data services. Today, one band just won't cut it.

So what can you do with a very old cell booster?


Unfortunately not much. Like most older technology today, it's not designed to be repaired or upgraded. That means, even if its fancy electronics work perfectly, it's practically useless today. However, a lot of older cell boosters are still usable because the frequencies they boost are still in use.

YX545_zoom.jpg


If you have a dual-band cell booster like this old YX545, believe it or not it will still work and work well, depending on which carrier you have. It boosts the 800 and 1900MHz bands. This means that you should be able to get some results from it. AT&T uses those frequencies for 5G, although Verizon and T-Mobile generally don't.

If you bought an LTE-only booster at some point in the 2010s, it will still work too. For the most part, all carriers use the same frequencies for LTE that they used then. You won't get 5G, but you will get something.

The issue is that you won't get everything


You probably don't want to do hours of research to figure out whether or not that booster will work for you on a day-by-day, place-by-place basis. You could try it and see if it does what you want it to, and that's probably the only thing you can do.

At issue here is that you just don't know what frequencies are being used. It's likely to change depending on where you are, and even to some degree depending on how many people are using cell service at that moment. That old booster won't be able to keep up. Like every other cellular-related thing you used back in 2009, it's not something you'd want to use today. (Remember that Blackberry you had in 2009? Would you want to use that today?)

We're just now starting to see the use of mid-band and millimeter-wave frequencies for 5G. It could be years, if ever, before we see consumer boosters for those frequencies, so the frequencies you use today will continue to be in use for a while. You just won't know which ones are being used without a cell meter.

So, the best thing to do is responsibly recycle it. At the very least, you're not putting toxic chemicals into the ground and the raw materials, the plastic and silicon and whatnot, can be used in something else, something that you might actually want to buy.

Get a new cell phone signal booster from Solid Signal


A cell booster made over a decade ago has had a good life. Today's boosters are more futureproof, and you should expect to get up to a decade of life from them, possibly more. We know today that it takes 3-5 years for new frequency allocations to really take effect, and right now there are no new frequencies being applied for. You shouldn't have to worry about mid-band or millimeter-wave frequencies for a while. So this is a perfect time to get a new booster.

Shop at Solid Signal for the best selection from all the top brands. If you're not sure what you want, call the experts! We're here for you at 888-233-7563 during East Coast hours. If it's after hours, no problem! Fill out the form below and we'll get right back to you.


The post What can you do with an old cell booster? appeared first on The Solid Signal Blog.

Continue reading...
0 Replies · 381 views
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in The Chit Chat Club
Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne


Get it?


An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
68658 Replies · 2680179 views
  • Like
Reactions: c-spand
dishstaller
I Wanna Talk About Me - Toby Keith
  • Like
Reactions: RaiderPower
Bobby
98.6 - Keith
harshness
I'm Easy - Keith Carridine
  • Like
Reactions: RaiderPower
gms49ers
It's Easy - Boston
RaiderPower
Take It Easy On Me - Little River Band
  • Like
Reactions: dishstaller
R
Last reply · posted in Computers and Gadgets
Lately my eight year old Dell laptop has been shutting off even when I have a full battery. I have had to keep it plugged up all the time to keep this from happening. Any idea what is causing this? I replaced the battery about three years ago.
2 Replies · 43 views
arlo
A recalibration might be needed. Even if it shows full, the individual cells may have become unbalaced. And the BMS chip in the battery reports false information to the pc.
Try this. Start it up in the bios/uefi and leave it there until the battery dies and it shuts off.
It might just keep running longer than in Windows. Or run for a short while and shut off.
If it's the first case. Probably just needs a balancing. If the latter, the pack might just be dead.
Not throwing stones but perhaps just a cheaply constructed battery with substandard cells. Could be.

Patience. Keep restarting it in bios/uefi until it won't fire up anymore.
Then plug the charger in and let it complete a full charge. And see what happens. If it's better.
Do the same thing one more time. Run it until it dies dead-dead. Then just let it charge, pc shut off.
When charged, it might be better. It might not be.

There are bench jigs that read the actual BMS and override it to let a tech manually monitor and charge the separate packs. They can also reset any "time bombs" in it that cause an otherwise good pack to show bad.
Maybe Santa will be good to me some year.

You might just need a new battery. Maybe the PC power management chip is going. A Dell common thing.
Leaving a laptop plugged in with a full battery is known to reduce the life. Asus for one recommends that you don't leave the charger plugged in all of the time even when shut down. And setting Windows to charge the battery to 85% instead of 100% increases life.
That's all I got.
dishstaller
That's all I got.
That was quite enough....I definitely learned something from your post. Thanks
TRG
TRG
Pub Member / Supporter
Last reply · posted in Computers and Gadgets
I set up a music server for my brother a few years ago. It's basically a small headless computer but it needs to have a DHCP IP address reserved for it in the router settings. This was easy to do in his DSL router. He's switching to Starlink now and I was wondering if these setting are easily accessible in the Starlink router. I'm pretty sure he will be getting the latest V5 router.
5 Replies · 282 views
b4pjoe
I set up a music server for my brother a few years ago. It's basically a small headless computer but it needs to have a DHCP IP address reserved for it in the router settings. This was easy to do in his DSL router. He's switching to Starlink now and I was wondering if these setting are easily accessible in the Starlink router. I'm pretty sure he will be getting the latest V5 router.
If you can't get into the router to reserve an IP address just don't use DHCP on the device that needs connected and assign it to a specific IP address in the network settings.
  • Like
Reactions: harshness
HipKat
I set up a music server for my brother a few years ago. It's basically a small headless computer but it needs to have a DHCP IP address reserved for it in the router settings. This was easy to do in his DSL router. He's switching to Starlink now and I was wondering if these setting are easily accessible in the Starlink router. I'm pretty sure he will be getting the latest V5 router.
They are not. Your best bet is to set up a third-party router, attached to the Starlink for your server, that you can get into, like a Linksys, etc
  • Like
Reactions: Foxbat
Foxbat
…it needs to have a DHCP IP address reserved for it in the router settings. This was easy to do in his DSL router. He's switching to Starlink now and I was wondering if these setting are easily accessible in the Starlink router. I'm pretty sure he will be getting the latest V5 router.
The Starlink V5 Install Kit I just got comes with the Mini Router. It is pretty limited in what it can do. For example, it can provide only one IP subnet at a time, no Guest Network, but it does support the pass-thru to a third-party Router. You can also split the Wi-Fi into separate 5 GHz & 2.4 GHz SSIDs to help some IoT devices that don't support 5 GHz bands to work.

The larger Starlink Router that still comes with the V4 Kit does support a Guest Network with separate IPv4 Subnet, but it's $120 from Starlink. And it still won't do DHCP Reservations.
harshness
If you can restrict the DHCP address space to assign addresses to one end of the subnet (i.e. x.x.x.50+), you can manually assign the IP address on pretty much any operating system. This is a default behavior on several popular routers. As the Router Mini only supports 235 devices, I expect that's already done.

Another option is to use a router that supports PoE to power the antenna. This article discusses that option (under PoE Power heading):

  • Like
Reactions: Foxbat
Foxbat
Now that I've had the v5 kit with the Mini Router, it's not as bad as I first thought. Yes, no DHCP reservations, but you can set up multiple SSIDs that have separate IPv4 subnets, and like the big brother, you can select from 192.168.x.0/24 or 10.x.0.0/16 (where "x" is 1-4).

You can also split a subnet and have different SSIDs for the 5 GHz and 2.4 GHz channels to handle some IoT devices. I haven't discovered what subnet the 2nd NIC on the router assigns, I'm guessing it's the first subnet.
dishstaller
Pub Member / Supporter Lifetime Supporter
Last reply · posted in The Chit Chat Club
2 Replies · 50 views
dishstaller
Sorry for posting the wrong link. Just corrected it.
dishstaller
Pub Member / Supporter Lifetime Supporter
Last reply · posted in The Chit Chat Club
Terrible tragedy. You would think that they would have safe guards in place that would prevent something like this from happening. I guess if you are going to ride in a passenger train it might be best to get a car near the rear.

2 Replies · 53 views
  • Sad
Reactions: Jimbo
Jimbo
Terrible tragedy. You would think that they would have safe guards in place that would prevent something like this from happening. I guess if you are going to ride in a passenger train it might be best to get a car near the rear.

They will have to look at the switching sections to determine WHY 2 trains were on the same track ... at the same time.
dishstaller
Thought this article might be of interest to some of you who might travel via train.