Social Feed

L
Last reply · posted in DISH Network Support Forum
Today as promised the Dish installer from (Dish Network Service Corporation, 7370 SW Durham Rd, Tigard,Oregon arrived) (503-670-4665 - 800-799-3246) From his truck he pulled a 24" dish antenna logo and all. It took him about 5 minutes to remove the old 500 and place the 24" on the mount. Hooked the meter up and in another 5 had it tuned and secured.

Now the big test. We went in and check the signal strength on 129, the 31 spot beam was 96, TP 27-85, TP-6 the worst one - low of 60 high of 76. I was satisfied and he left. I placed the TV on Rave SP-6 for 3 hours and never once did the signal drop. Location N/W Oregon, rainy day with lots of clouds, whats new here. He mentioned that dish announced this problem for the N/W about 2 months ago. So if you have troubles with the signal on 129 their is a possible fix with the 24" antenna. I asked him who makes it and he didn't know as they receive them from Dish. He also said: "tune the 129 on TP-6 usually the lowest one." Their was a post yesterday about which TP to use. I will watch with hope and expectations. More to follow if problems arise.

Larry N/W Oregon where it never rains::hungry:
12 Replies · 2839 views
ralfyguy
Today as promised the Dish installer from (Dish Network Service Corporation, 7370 SW Durham Rd, Tigard,Oregon arrived) (503-670-4665 - 800-799-3246) From his truck he pulled a 24" dish antenna logo and all. It took him about 5 minutes to remove the old 500 and place the 24" on the mount. Hooked the meter up and in another 5 had it tuned and secured.

Now the big test. We went in and check the signal strength on 129, the 31 spot beam was 96, TP 27-85, TP-6 the worst one - low of 60 high of 76. I was satisfied and he left. I placed the TV on Rave SP-6 for 3 hours and never once did the signal drop. Location N/W Oregon, rainy day with lots of clouds, whats new here. He mentioned that dish announced this problem for the N/W about 2 months ago. So if you have troubles with the signal on 129 their is a possible fix with the 24" antenna. I asked him who makes it and he didn't know as they receive them from Dish. He also said: "tune the 129 on TP-6 usually the lowest one." Their was a post yesterday about which TP to use. I will watch with hope and expectations. More to follow if problems arise.

Larry N/W Oregon where it never rains::hungry:

I got exactly the same readings with an old D1000. I am in Oklahoma. I wonder what I could pull with a 24" dish...:p
digiblur
I got exactly the same readings with an old D1000. I am in Oklahoma. I wonder what I could pull with a 24" dish...:p

I remember hooking up a 301 to my 90cm and almost hitting over 115 on some TP's on 129W. ;)
RandallA
I remember hooking up a 301 to my 90cm and almost hitting over 115 on some TP's on 129W. ;)

The 301s read higher signal strength. I'm getting 100 on TP 31 on a 311 but 91 on the 622 and 211. But yeah, a bigger dish always help and the location makes a big difference too. We on the West coast and specially the Pacific Northwest are screwed with 129 and the only solution is a bigger dish.
RoyW
The 301s read higher signal strength. I'm getting 100 on TP 31 on a 311 but 91 on the 622 and 211. But yeah, a bigger dish always help and the location makes a big difference too. We on the West coast and specially the Pacific Northwest are screwed with 129 and the only solution is a bigger dish.

Although I'm further south then you after reading the posts from one of the Texas members I decided to give our 1000.2 one more shot. Initially I tweaked off 119 and was able to raise its average signal strength by about 8 points. To my dismay this dropped TP6 off 129 from around 53 to about 44.

Since I'd marked up my dish with bench marks I was able to place it back in its original position and again had about 53 off TP6 on 129. Next I tried shifting the dish slightly to the left and then right while on TP6 off 129 without loosening the bolts, in each case it dropped the signal strength. I also tried tilting and lowering the elevation by hand, again without loosening the bolts only to have the signal strength drop.

At this point I reviewed my skew for about the fifth time and its set exactly on 93 as prescribed for my zip code. To be fair since our area rarely gets any rain we are fairly insulated from problems associated with fade but its the principle of the thing that bothers me. Should I start having problems it appears my alternatives are to try a single dish option for 129 and a DPP44 switch. I subscribe to a foreign channel off 148 and because of neighbors trees can no longer pick up 61.5.
RandallA
Believe me, I tried peaking the 1000.2 as much as I can. I tweaked the skew, elevation and azimuth and nothing will give me anything better than 60 on TP6. I do get 91-94 on TP 31 and 119 and 110 come at 100s and 90s. So that tells me the dish is pretty much peaked to the max but because of our location certain TPs on 129 will not get better signals.

For my location the manual says, Azim=160, Elev=45, Skew=87. I have it at Azim=160, Elev=46, Skew=86 and I get the best readings. So yes, the manual is off in some of the numbers so playing with the angles may give you better results but will not get you decent readings on some TPs. And yes my dish is perfectly leveled.

Another thing that bugs me is that TP31 and TP30 have good readings, 90s but most of the other TPs are in the 60s. E* should raise the power level on all TPs but wait, E5 is crippled and they CAN'T. They need to conserve power so it lasts them another 2 years.
digiblur
Another thing that bugs me is that TP31 and TP30 have good readings, 90s but most of the other TPs are in the 60s. E* should raise the power level on all TPs but wait, E5 is crippled and they CAN'T. They need to conserve power so it lasts them another 2 years.

They are trying to conserve fuel as much as possible....not battery/solar power. The battery/solar power is a whole additional issue with the bird.
RoyW
Believe me, I tried peaking the 1000.2 as much as I can. I tweaked the skew, elevation and azimuth and nothing will give me anything better than 60 on TP6. I do get 91-94 on TP 31 and 119 and 110 come at 100s and 90s. So that tells me the dish is pretty much peaked to the max but because of our location certain TPs on 129 will not get better signals.

For my location the manual says, Azim=160, Elev=45, Skew=87. I have it at Azim=160, Elev=46, Skew=86 and I get the best readings. So yes, the manual is off in some of the numbers so playing with the angles may give you better results but will not get you decent readings on some TPs. And yes my dish is perfectly leveled.

Another thing that bugs me is that TP31 and TP30 have good readings, 90s but most of the other TPs are in the 60s. E* should raise the power level on all TPs but wait, E5 is crippled and they CAN'T. They need to conserve power so it lasts them another 2 years.

My TP31 and TP30 readings are only in the lower eighties so maybe the next time I feel like wasting some time I'll try tweaking my Skew slightly and see if that helps. Thank you for pointing out the fact that it had helped further north.
S
Great signal strength increase!

Installed my new 24" dish today. I live in Western Oregon and have had occasional loss of signal. The new dish added 10 pts to some of the TP's.
TP 24 Old
6 65 78
27 67 82
30 85 94
31 90 101

It was definitely worthy the investment!
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in The Chit Chat Club
Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne


Get it?


An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
68807 Replies · 2689931 views
  • Like
Reactions: c-spand
RaiderPower
Little Willy - Sweet
  • Like
Reactions: dishstaller
dishstaller
I Know a Little - Lynyrd Skynyrd
EatMyVolts
Little Bitty Pretty One -- Thurston Harris
  • Like
Reactions: Bobby
long_time_Dish
My Little Town - Paul Simon
H
Small TOWN -John Mellencamp
"MysteryMan"
Pub Member / Supporter Cutting Edge
Last reply · posted in Computers and Gadgets
I created this thread on the original Edgecutter Cutting Edge Forums site. It's simply a place for those to review the latest software available for those using Windows 10 and Windows 11. To date it has received 112,559 views. I have been asked by staff to continue this thread here.
525 Replies · 48784 views
EarDemon
If it wasn't for what I want, I wouldn't need any of this.

Do I need a collection of handheld radios, scanners and speed enforcement countermeasures? Nope, but I want them. Very little, if any of the software used to interface with these devices is available on Linux.
WhiteBeard
If it wasn't for what I want, I wouldn't need any of this.

Do I need a collection of handheld radios, scanners and speed enforcement countermeasures? Nope, but I want them. Very little, if any of the software used to interface with these devices is available on Linux.
To each there own but I've found that Windows can't do much more than Linux can. Can't have everything. ☹️
  • Haha
Reactions: meStevo
EarDemon
To each there own but I've found that Windows can't do much more than Linux can. Can't have everything. ☹️
For niche use cases, yes I agree. Kali for ethical hacking and security testing, and running a Cacti server for network monitoring are the two things I have experience in. Plus thousands and thousands of other things, but for every day use I just can't see it. The owner of the GMRS repeater that I pay to access is changing the Tx DPL tones tomorrow, while Chirp is available on Linux, the software to program my MXT500 is not.

I run Fedora and Ubuntu in VMWare, honestly I don't care much for the UI of either of them and I don't feel like spending days/weeks to customize the UI to make it look Windows-like when I could just use Windows. The cartoonish dock at the bottom of the screen reminds me of Apple products.
harshness
I don't care much for the UI of either of them and I don't feel like spending days/weeks to customize the UI to make it look Windows-like when I could just use Windows.
What is so fantabulous about the Windows UI? By many accounts, it has been going downhill since Windows 7.

There are Linux desktops that offer Windows or Mac UIs, yet you don't hear much chatter about them outside of questions about when the creators might get sued.
  • Like
Reactions: HipKat
EarDemon
What is so fantabulous about the Windows UI?
Because it's what I prefer. I know I've said this a few times, I use Open Shell to give me the cascading start menu a la WIN 95 and NT4.0. The only reason I went from Windows Vista to 7 back in the day was because of Classic Shell. I cannot stand anything other than the OG start menu from 30+ years ago. I'm using ExplorerPatcher to give me Windows 10 UI elements of the taskbar and right click context menus.

If you could take a look at how I set up Windows 95, you'd find many similarities to how I use 11.
  • Like
Reactions: cp2k
EarDemon
I could probably use that as a starting point, but I don't like the full size icons. If you have to click on each folder that's also a no-go for me, it has to be cascading.

I used to have Peppermint Linux in a VM, that was about as close as I could get to recreating a Windows NT4.0 style of menu structure, but I could never get it to scale properly in VMWare on a 4K display and eventually gave up.

Whatever the boot up time it's fine with me. The longest part of my bootup is the HP SureStart BIOS integrity check. Once that is done, it's only a few more seconds. I haven't done this reg tweak yet since the reformat, but I switched the bootup animation to the Windows 10 style spinning circle of dots, and it's two and a half rotations. I can live with that.
harshness
Because it's what I prefer.
I hope you don't believe that makes it wonderful (especially when you're using workarounds for Microsoft's malfeasance).

I use LibreOffice as opposed to Microsoft office (even in Windows) because it's UI is like the Office of old, so I'm putting my money where my mouth is (in a manner of speaking). The ribbon was one of the worst ideas to come out Redmond.
HipKat
I could probably use that as a starting point, but I don't like the full size icons. If you have to click on each folder that's also a no-go for me, it has to be cascading.

I used to have Peppermint Linux in a VM, that was about as close as I could get to recreating a Windows NT4.0 style of menu structure, but I could never get it to scale properly in VMWare on a 4K display and eventually gave up.

Whatever the boot up time it's fine with me. The longest part of my bootup is the HP SureStart BIOS integrity check. Once that is done, it's only a few more seconds. I haven't done this reg tweak yet since the reformat, but I switched the bootup animation to the Windows 10 style spinning circle of dots, and it's two and a half rotations. I can live with that.
I used to pin the C: drive to the Win Taskbar and it would open in cascading style
"MysteryMan"
2026-10 Preview Update Builds: 26300.9818 and 26200.9818 (KB5127936) has been released. Moderate time needed for those choosing to perform a manual download/install/restart. Quality improvements only. No new operating system features.
  • Like
Reactions: Tweek
JSheridan
Actually it looks like there are a lot of features new or updated, although most are on a gradual rollout schedule.

T
There were several new updates today.
BlackHitachi
Supporting Founder
Last reply · posted in Movie Talk
Since the Reds have there thread we should too!

Last watched Nine inch Nails
Next 3:10 to Yuma
5400 Replies · 512253 views
osu1991
  • Like
Reactions: dfergie
dishstaller
Just watched Napoleon. Good night.....all of those young men dying for the egos of their leaders. Now we can kill at a distance, back then you saw the man you were killing eye to eye.
osu1991

View: https://youtu.be/0B5v6QZ5R3g?is=uXG8Z3-HITRAwxOm



Demolition Man was this afternoon's entertainment.
long_time_Dish
The rat burger and the three shells...yep, that was good stuff! :biggrin
meStevo
Wild Horse Nine was fantastic.
osu1991
Pub Member / Supporter
Last reply · posted in TV Shows
13 Replies · 322 views
Foxbat
Apparently I'm not a big enough nerd🤓 since I did not read every Marvel Comic Book ever published. If I had, I might be comparing the comics' version of events compared to what's transpiring in "Visionquest". So, I am enjoying the series a lot, not weighed down by previous expectations, knowing only the Avengers MCU movies and the "Wandavision" / "Agatha All Along" TV series.

I found the Mr Know-it-All channel from his discussion about "Star Trek: Strange New Worlds" and he's been gleefully picking these episodes apart, referencing the Marvel comics from the 1939 on. Turns out A.I. has been around since before World War II, at least in the comics. (Robots before that, yes, yes.) This show is going back into the archives.
  • Like
Reactions: osu1991
Foxbat
I'm expecting the finale to basically bring Vision into play for the Doomsday movie next month.
  • Like
Reactions: osu1991
osu1991
annoying they went with single episodes for the last two after releasing two a week for the first 3 weeks
Foxbat
annoying they went with single episodes for the last two after releasing two a week for the first 3 weeks
I thought they were effectively releasing a longer episode 7 and 8 instead of shorter episodes 7 & 8 this week and 9 & 10 next week. It felt like they were packing more into this episode.

edit: But you're right, the run time of the first three pairs of episodes was 100 minutes on average. Episode 7 clocks in at 65 minutes. 😕
  • Like
Reactions: MikeD-C05
osu1991
FYI…there are after credit scenes in the finale
  • Like
Reactions: Foxbat
ewindowman
Lifetime Supporter
Last reply · posted in DISH Network Support Forum
Looks like dish is Bankrupt. Filling tomorrow Tuesday June 30th
477 Replies · 17313 views
comfortably_numb

Too bad their service is expensive and their coverage sucks compared to the other two of the Big 3
Juan
Too bad their service is expensive and their coverage sucks compared to the other two of the Big 3
Was that a back door compliment for Verizon?
  • Like
Reactions: charlesrshell
comfortably_numb
Was that a back door compliment for Verizon?

And TMO. If anybody's lagging behind the most, it's ATT.
ERSanders
The short term financial thinking by MBAs is what killed Xerox. Ask me how I know!
Juan
The short term financial thinking by MBAs is what killed Xerox. Ask me how I know!
I thought it was when Bill Gates stole DOS
dishdude
I thought it was when Bill Gates stole DOS

And Steve Jobs stole the mouse and GUI
ERSanders
The short term financial thinking by MBAs is what killed Xerox. Ask me how I know!
Actually I survived despite them for 31 years and two expait assignments. But the quest for the current quarter's profits doomed long term vision, planning and actions.
S
I thought it was when Bill Gates stole DOS
He bought that for $50,000. What he bought was originally called QDOS (Quick and Dirty Operating System) from Seattle Computer Products which was designed to be similar to CP/M - an OS for the Intel 8080. Seems like a decent investment. ;-)

There have been claims that the original developer of QDOS stole CP/M code and according to legend there is some command that you can type into MS-DOS that makes it print the name of the developer of CP/M, thus proving theft, but no one seems to know what that command actually is. ;-)
  • Like
Reactions: charlesrshell
fmj77
And TMO. If anybody's lagging behind the most, it's ATT.
ATT has the best service by far in my area, with Verizon being a distant second. T Mobile service is non-existent in these parts.
comfortably_numb
ATT has the best service by far in my area

I've never been to NC, but I can't think of anyplace in the Midwest or West where AT&T outperforms Verizon or T-Mobile, it seems to me they just don't have as many towers here
  • Like
Reactions: charlesrshell
G
Last reply · posted in DISH Network Support Forum
After a strange reboot last night in the middle of viewing, this morning several more reboots and about a half an hour download.
5 Replies · 541 views
Almighty1
Just did the update check manually about an hour ago with Hopper 3 on H713 and Hopper Plus on P15403.
Noticed something new when I clicked on the Update Software, it presented a pop-up as follows:
"Update software 1573
Update later Update now Cancel" with those three buttons which did not exist before.

After updating the H715 - I guess there must be major bugs as both H709 and H714 were skipped.

So here are the issue(s):

Issue #1
It did fix the problem with H713 which was:
"One of the problems I am seeing is that the Available Joey Software section no longer is showing the Android TV versions even after a manual software reset twice and the nightly reboot. Until it does, nether Technician Android TV download and Hopper Plus is able to check, download and update the Android TV software."

This was a major problem with H703.

H710 removed that dependency so H711 and H712 were working without that dependency but H713 brought it back which is fixed in H715 as no P versions or Android TV versions are shown in the Available Joey Software on the main Diagnostics screen.
However, with that said, the TECHNICIAN SETTINGS, Download ATV (Android TV) Files is not working correctly as the Download ATV Files shows:
"Download ATV Files 3000
Download in progress. This operation will be
complete when the files are downloaded

Joey 4 : P554- Failed
Joey 4 : P55403- Failed
Wireless Joey 4 : P654- Failed
Wireless Joey 4 : P65403- Complete
HopperPlus : P154- Complete
HopperPlus : P15403- Failed

OK"
From what I can tell, each of them goes through the Downloading followed by the Processing stages first before it goes into the Failed or Complete stage. It seemed to be going in a loop earlier as it will start downloading from the first item being the Joey 4 each time before it eventually stopped. This is the first time ever since 2023 that I had ever seen it Failed.

With that said, the dependency appears to still be required for the Hopper Plus to check, download and update the Android TV software as it says Failed, No Target when going to "Device Preferences", About, "Software Update"

Issue #2
Still cannot cast to Hopper 3 with Hopper Plus(Software P15317) with the Hopper Plus "Google Chromecast Built-In" feature" as it shows up as a casting device when the Hopper Plus is online and disappears when the Hopper 3 and Hopper Plus does it's nightly reboots but times out when one tries to cast to it and always shows up as Not available in the Google Home app on Android phone. No one else anywhere on the internet had confirmed whether it is working for them or not. Per brittanygarden in DM on October 16, 2026:
"We've been working with Google on this. We have a fix on the Google side projected for Q4. I know we're in Q4 now, but I will try to get a narrowed down timeline for you."

brittanygarden and Rick Durham

jsmit86 and naptime - If you are able to use H715, does the issue mentioned below still exist?
  • Like
Reactions: charlesrshell
jsmit86
Just did the update check manually about an hour ago with Hopper 3 on H713 and Hopper Plus on P15403.
Noticed something new when I clicked on the Update Software, it presented a pop-up as follows:
"Update software 1573
Update later Update now Cancel" with those three buttons which did not exist before.

After updating the H715 - I guess there must be major bugs as both H709 and H714 were skipped.

So here are the issue(s):

Issue #1
It did fix the problem with H713 which was:
"One of the problems I am seeing is that the Available Joey Software section no longer is showing the Android TV versions even after a manual software reset twice and the nightly reboot. Until it does, nether Technician Android TV download and Hopper Plus is able to check, download and update the Android TV software."

This was a major problem with H703.

H710 removed that dependency so H711 and H712 were working without that dependency but H713 brought it back which is fixed in H715 as no P versions or Android TV versions are shown in the Available Joey Software on the main Diagnostics screen.
However, with that said, the TECHNICIAN SETTINGS, Download ATV (Android TV) Files is not working correctly as the Download ATV Files shows:
"Download ATV Files 3000
Download in progress. This operation will be
complete when the files are downloaded

Joey 4 : P554- Failed
Joey 4 : P55403- Failed
Wireless Joey 4 : P654- Failed
Wireless Joey 4 : P65403- Complete
HopperPlus : P154- Complete
HopperPlus : P15403- Failed

OK"
From what I can tell, each of them goes through the Downloading followed by the Processing stages first before it goes into the Failed or Complete stage. It seemed to be going in a loop earlier as it will start downloading from the first item being the Joey 4 each time before it eventually stopped. This is the first time ever since 2023 that I had ever seen it Failed.

With that said, the dependency appears to still be required for the Hopper Plus to check, download and update the Android TV software as it says Failed, No Target when going to "Device Preferences", About, "Software Update"

Issue #2
Still cannot cast to Hopper 3 with Hopper Plus(Software P15317) with the Hopper Plus "Google Chromecast Built-In" feature" as it shows up as a casting device when the Hopper Plus is online and disappears when the Hopper 3 and Hopper Plus does it's nightly reboots but times out when one tries to cast to it and always shows up as Not available in the Google Home app on Android phone. No one else anywhere on the internet had confirmed whether it is working for them or not. Per brittanygarden in DM on October 16, 2026:
"We've been working with Google on this. We have a fix on the Google side projected for Q4. I know we're in Q4 now, but I will try to get a narrowed down timeline for you."

brittanygarden and Rick Durham

jsmit86 and naptime - If you are able to use H715, does the issue mentioned below still exist?
I have not been updated to 715 yet. I am on a QE "Beta" or Test version that did fix the audio issue. The last communication I had with the team mentioned that the full release of that fix was likely in December.
It would be nice to know if 715 does solve that issue of no audio when Dolby is ON, during 4K HDR events.
Almighty1
I have not been updated to 715 yet. I am on a QE "Beta" or Test version that did fix the audio issue. The last communication I had with the team mentioned that the full release of that fix was likely in December.
It would be nice to know if 715 does solve that issue of no audio when Dolby is ON, during 4K HDR events.
Interesting, is QE "Beta" or Test version different than the H708 you had mentioned that they rolled you back to or is that a newer version after that?
  • Like
Reactions: charlesrshell
jsmit86
Interesting, is QE "Beta" or Test version different than the H708 you had mentioned that they rolled you back to or is that a newer version after that?
I think it is, but I am not aware of specific differences.
My original communication of the issue was very detailed, and they had the team work on it and felt they knew what was causing the issue.
The rollback to 708 confirmed that 708 did not have that problem.
I got an email in late October asking if I would be open to checking if a beta version had the problem. I agreed to the test, and it did not have the dolby problem.
david_jr
Not sure if it was this update or a previous one, but both my H3's had the bug where I couldn't use FF without screwing up the recording permanently. If I tried 60X for instance it would fast forward for a bit then go to the end of the recording and not let me get back to where I was trying to get no matter what. The temp fix was to use the skip ahead which for whatever reason still worked. Annoying having to skip ahead through 8 minutes or so of commercials on live sports talk recordings. Well it is now fixed, but not sure when that happened because I haven't had the nerve to try FF until this last week when I discovered it had been fixed. Working properly now on both my H3's. However my Dish Anywhere app is still not allowing me to use both H3's as feeds out. Tested this again a few days ago with my son and we both couldn't watch at the same time, even though we were connected to the other H3. If he was using DA and I attempted to use it with the other H3, it would bring up a message stating another user was using DA and do you want to take over. Very frustrating hoping they fix this soon.
  • Like
Reactions: charlesrshell
Bobby
Supporting Founder Lifetime Supporter
Last reply · posted in DISH Network Support Forum
This is a thread that will keep you apprised of 4K events that will be showing on Dish channel 540. Keep looking here for information.

As of today, 9-27-17, there are no scheduled events posted for the next 2 weeks. That is subject to change on a daily basis.
773 Replies · 169528 views
Bobby
CFB, Wisconsin at Iowa, Saturday 10-31, 9AM PDT, Channel 148-01.
CFB, Arizona St at BYU, Saturday 10-31, 12:30PM PDT, Channel 148-01.
  • Like
Reactions: charlesrshell
Bobby
CFB, Alabama at LSU, Saturday 11-7, 12:30PM PST, Channel 148-03.
Bobby
CFB, UCLA at Minnesota, Saturday 11-7, 9AM PST, Channel 148-01.
CFB, Iowa at Northwestern, Saturday 11-7, 4:30PM PST, Channel 148-01.
  • Like
Reactions: charlesrshell
Bobby
CFB, Texas at LSU, Saturday 11-14, 4:30PM PST, Channel 148-03.
Bobby
CFB, Northwestern at Ohio St, Saturday 11-14, 9AM PST, Channel 148-01.
CFB, Utah at Arizona, Saturday 11-14, 4:30PM PST, Channel 148-01.
  • Like
Reactions: charlesrshell
Foxbat
Supporting Founder Pub Member / Supporter Lifetime Supporter
Last reply · posted in Computers and Gadgets
Hmmm, Apple iCloud appears to be missing from the Internet. Attempting to connect yields:
1794355836427.webp
Plus, lots of prompts to enter my iCloud credentials.
1794356039809.webp​
3 Replies · 78 views
K
I'm not seeing any issues.
meStevo
looks like an incident is clearing up


1794358560136.webp
  • Like
Reactions: Foxbat
Foxbat
The Apple Support System Status page is showing mostly green now, with Resolved status for the outage that started 17:49 and ended around 19:22 (I guess EST)
1794359273616.webp
Bruce
Supporting Founder Lifetime Supporter
Last reply · posted in Internet Television (IPTV) Discussion Forum
Comcast is the first to report, with a massive 274,000 loss in video subscribers.

In the 3Q of 2016, Comcast had 21.42 million video subscribers and was the #1 provider, now at 10.39 million and is the #3 Provider, YTTV is #2 ( who also surpassed DirecTV-8 Million and Dish-under 5 Million), Charter/Spectrum is #1.

42 Replies · 1738 views
  • Like
Reactions: Howard Simmons
R
In my area Cox (now Spectrum) has run everything underground instead of on poles.
  • Like
Reactions: MikeD-C05
Jimbo
In my area Cox (now Spectrum) has run everything underground instead of on poles.
Thats good, the neighborhood generally look better with buried plant ... until someone puts a shovel into the line planting the Spring Garden. :(
Bobby
Thats good, the neighborhood generally look better with buried plant ... until someone puts a shovel into the line planting the Spring Garden. :(
In my local area all underground utilities are under the sidewalk. Of course from there, when entering your property, They are at least 18" in your dirt.
Jimbo
In my local area all underground utilities are under the sidewalk. Of course from there, when entering your property, They are at least 18" in your dirt.
I bet MOST of them are NOT 18", they may suppose to be, but I doubt they are .

Edison is definitely deep enough, but thats the only one ...
B
Thats good, the neighborhood generally look better with buried plant ... until someone puts a shovel into the line planting the Spring Garden. :(
My fiber isp put everything in conduit, except for the drop line to the NID and it it buried 10 inches
  • Like
Reactions: Jimbo
R
Thats good, the neighborhood generally look better with buried plant ... until someone puts a shovel into the line planting the Spring Garden. :(
My area is very rocky, so there will be no shovels into the lines. Most of the lines were bored and the one's not bored where dug at least 18" deep. Cox had flagged my yard for them to dig up. But the foreman of the crew said he was not going to tear up my grass. He ended up installing the cable across the street at a vacant lot instead and bored the street for my pedestal. The line from the pedestal to my house could be damaged being it is fairly shallow.
Jimbo
My fiber isp put everything in conduit, except for the drop line to the NID and it it buried 10 inches
Really, you Lucky Dog !

Do you Work for that ISP ? :biggrin
Bobby
I bet MOST of them are NOT 18", they may suppose to be, but I doubt they are .

Edison is definitely deep enough, but thats the only one ...
I did the underground trench utility designs for 9 years. Gas and electric were 24". Telephone and CATV were 18". These were for new construction. Add on construction could be anywhere. All of the utilities went from their terminal points to a common utility point on the house. They were in a single trench.
So, if theres a issue with any buried line, the sidewalk needs to be dug up as well ???
That sucks.
Sometimes…. electric and CATV are in conduit so replacement is pretty easy. Telephone, specifically Pacific Telephone, Pacific Bell, SBC, ATT are direct buried and use encap termination directly onto the feed cable. That is always a sidewalk digup.
Jimbo
I did the underground trench utility designs for 9 years. Gas and electric were 24". Telephone and CATV were 18". These were for new construction. Add on construction could be anywhere. All of the utilities went from their terminal points to a common utility point on the house. They were in a single trench.

Sometimes…. electric and CATV are in conduit so replacement is pretty easy. Telephone, specifically Pacific Telephone, Pacific Bell, SBC, ATT are direct buried and use encap termination directly onto the feed cable. That is always a sidewalk digup.
Ok, your talking in the right of way ...
I thought you were talking about from the ped to the houses.

Fortunately you don't usually get Cable cuts Under a sidewalk, usually its when a Construction crew us digging with major equipment.

The drops to the house are not going to be very deep, sometimes barely under the sod. 6" is a godsend.
osu1991
I'm fortunate to have 3 fiber providers now.

Cox and T mobile bored and put conduit in before pulling the fiber thru the easement in my neighborhood . Windstream Kinetic I can't remember if they pulled conduit first or not. I remember they didn't have a boring machine when they came thru my yard, they used that for the mainline crossing under the street but had a vibratory plow in my backyard. I remember seeing some blue conduit just don't remember where it was being used. Windstream barely put the fiber run from the pedestal to my house about 2 inches underground. Landscaper hit it while putting landscaping around the pedestal they added to my yard. I made sure they buried it at least 12 inches when they replaced it.

AEP/ PSO the electric company has their main distribution lines running on poles along the back of my property. Cox has their main distribution line hung on those poles before going underground through the neighborhood.

I'm in the middle of a damage claim and about to take them to court as insurance is trying to get out of it claiming the lines were too low. Had an oversized load get lost and try to turn around in an older neighborhood. Pulled down 5 blocks of fiber with separate fiber lines belonging to the city, Cox/Spectrum and ATT.
B
My area is very rocky, so there will be no shovels into the lines. Most of the lines were bored and the one's not bored where dug at least 18" deep. Cox had flagged my yard for them to dig up. But the foreman of the crew said he was not going to tear up my grass. He ended up installing the cable across the street at a vacant lot instead and bored the street for my pedestal. The line from the pedestal to my house could be damaged being it is fairly shallow.
No, but it is a coop. I am just a member and subscriber
Really, you Lucky Dog !

Do you Work for that ISP ? :biggrin
Bruce
Supporting Founder Lifetime Supporter
Last reply · posted in Internet Television (IPTV) Discussion Forum
I was reading this article


That said this-
Last summer, for the first time, streaming services like Netflix and Amazon Prime claimed the largest share of the television viewing audience, surpassing both cable and broadcast TV. Streaming captured 34.8 percent of July viewers, according to Nielsen data, compared to 34.4 percent for cable and 21.6 percent for broadcast.

And then, sometime in the second half of 2022, cord-cutters became the majority. The share of cable and satellite television subscribers dipped to 48 percent, according to a report from Samba TV, a television technology company.


Now I do not consider those with YTTV and the likes, Cord Cutters, but they still do not have Traditional Cable/Satellite delivered Live TV, so I decided to do the math.

There are, now, 129 Million Households in the United States.

In 2015, there were 100 Million Cable/Sat Subscribers , no streaming Live TV Service.

Today, there are 66 Million Live TV subscribers, including Cable, Satellite and Streaming.

Roughly, Streaming Live TV has 14 Million subs including all of them.

So that means, Cable/Satellite now has, roughly, 51 Million Households

So in just 8 years, lost 49% of their subscribers and by the end of this year, expected sub count to be, roughly, 45 million households.

That means a total loss of 55% since 2015 at the end of 2023.

But out of 129 Million households, 45 million will mean only 35% will get Cable/Satellite Delivered Live TV by the end of 2023.

Imagine what 2024 will be like.
918 Replies · 73745 views
  • Wow
Reactions: MikeD-C05
Bruce
According to industry figures reported by Sports Media Watch, this year's World Series averaged 11.69 million viewers on FOX, down 26% from the 15.71 million average the 2025 series delivered.
  • Like
Reactions: Howard Simmons
Jimbo
According to industry figures reported by Sports Media Watch, this year's World Series averaged 11.69 million viewers on FOX, down 26% from the 15.71 million average the 2025 series delivered.
That thier own stupidity ...

They make it hard to find the game when its on FOX 1 game, then FS1, then on Tru or some other little ity biyy channel that people rerely watch and can't find. (I don't know if FOX is TRU or not, but thats what I'm saying, they put games on obscure channels and expect people to easily find it and watch.
Bruce
That thier own stupidity ...

They make it hard to find the game when its on FOX 1 game, then FS1, then on Tru or some other little ity biyy channel that people rerely watch and can't find. (I don't know if FOX is TRU or not, but thats what I'm saying, they put games on obscure channels and expect people to easily find it and watch.
Every WS game was on the main Fox Broadcast Channel, what are you referring to?
AZ.
AZ.
Every WS game was on the main Fox Broadcast Channel, what are you referring to?
Throughout the playoffs most games were not over the air. They were on FS1 or TrueTV, HBO, TBS....So without a sports package you need FS1, and the others you need a old school TV package. If I had to guess, close to 75% of playoff games were not on free local TV.
Bruce
Throughout the playoffs most games were not over the air. They were on FS1 or TrueTV, HBO, TBS....So without a sports package you need FS1, and the others you need an old school TV package. If I had to guess, close to 75% of playoff games were not on free local TV.
But I never posted about the playoffs, only the World Series.

And a 4 million drop in households is a big deal, specially what Fox pays for it, they are already losing money on the MLB contract, now even more, since they might have to give some of the money back to advertisers, since it might of not made certain ratings goals.
Bobby
But I never posted about the playoffs, only the World Series.

And a 4 million drop in households is a big deal, specially what Fox pays for it, they are already losing money on the MLB contract, now even more, since they might have to give some of the money back to advertisers, since it might of not made certain ratings goals.
Last year it was the Dodgers and Bluejays. This year is was the Brewers and the Rays, two teams that never won a World Series. Last year the Dodgers were the former year champion, can they do a repeat against a Toronto team that looked unbeatable. That World Series was a classic between two teams that really wanted it. The highlight of this year was can Milwaukee go 4-0 like they did to the Dodgers, and they just about did.
AZ.
AZ.
Last year it was the Dodgers and Bluejays. This year is was the Brewers and the Rays, two teams that never won a World Series. Last year the Dodgers were the former year champion, can they do a repeat against a Toronto team that looked unbeatable. That World Series was a classic between two teams that really wanted it. The highlight of this year was can Milwaukee go 4-0 like they did to the Dodgers, and they just about did.
Yep ratings have lots to do with what teams are playing. Large market over smaller. Underdog teams people want to root for. But If you make it hard to watch all the playoffs, you will get less interest for the World Series.
TRG
TRG
According to industry figures reported by Sports Media Watch, this year's World Series averaged 11.69 million viewers on FOX, down 26% from the 15.71 million average the 2025 series delivered.

People are tired of watching the World Series without the Yankees. :devilish :biggrin
Bruce
Yep ratings have lots to do with what teams are playing. Large market over smaller. Underdog teams people want to root for. But If you make it hard to watch all the playoffs, you will get less interest for the World Series.
Except last year, the playoffs were aired on the same channels as this year.
Jimbo
People are tired of watching the World Series without the Yankees. :devilish :biggrin
Not Me, I rather enjoy it ...
  • Like
  • Haha
Reactions: TRG and Foxbat
Jimbo
Except last year, the playoffs were aired on the same channels as this year.
Quick Question, WITHOUT Looking it up ...
Who played in the World Series last year ?
Jimbo
Except last year, the playoffs were aired on the same channels as this year.
True, but you had 2 Large Markets in it .
  • Like
Reactions: Foxbat
Bruce
Quick Question, WITHOUT Looking it up ...
Who played in the World Series last year ?
Two MLB teams.
Jimbo
Two MLB teams.
Now, having low numbers this past year doesn't surprise me at all, you had 2 teams that don't like to spend tons of money and they are not your Large markets.
TRG
TRG
Not Me, I rather enjoy it ...
I thought you might like that. :biggrin
Jimbo
But I never posted about the playoffs, only the World Series.

And a 4 million drop in households is a big deal, specially what Fox pays for it, they are already losing money on the MLB contract, now even more, since they might have to give some of the money back to advertisers, since it might of not made certain ratings goals.
I guess they should figure that out ... maybe not offer as much if they can't afford it next time.