Search results for query: *

I have version 1.20.1, gladly upload for the masses. :)

I see a lot of confusion in the audio realm and the use of terminology. AC-3 is the coined term for Dolby Digital encoded stream. A dvd player, STB etc; when set to "pcm", will decode the surround signal whether it is AC-3 or whatever else it can do and then send it out HDMI or opt/coax. When...

For racing information you should check out Ricks Satellite forum. That is the place for motor head, among other great information. :) Ricks Satellite Wildfeed and Backhaul Forum

So last night I was scanning the arc with my fortec mercury II with G-box and noticed my counts are off from what they were. I had noticed this with the coolsat over the past week but now its way off. Is it odd to only go to like -480 on the east to 200 on the west? This tells me my arm isn't...

I need to tweak my f/d as well. Unfortunately I busted the set screw mount from the scalar ring on my c2. I was able to epoxy it back in place. I also glued the feed horn in place at according to where my chaparal feed horn stuck out. Anyway my thought was I can adjust the distance by using...

awesome! That is the way good businesses get repeat customers. :up

I am not sure which 10ft dish you have but perhaps your calculations are off. If you have the Geosatpro C2 lnbf then make sure it is rotated 90deg. so that the 0 mark is facing 9 or 3 o' clock when mounted in the scalar ring. Here is a list of dish specs that might help you with your f/d settings.

I put in an order before you posted this but after you stated you ran out of the first batch. I was under the impression the discount was still in place through the 25th, regardless of "in stock" or not. If this should have been a PM I apologize but, thought others may have been in the same...

So then how are you doing this exactly crackt?

how do i switch between them with the ecoda? does it matter which one is on the 22kHz leg? I assume i set every sat I want to get with the 22k leg that it needs to be on to function right? I do not see how that would stop the Ku side from moving with the diseqc 1.2 command I use on the c-band...

I was afraid this was going to be a tough one, if not impossible. What if one used an A/B box, that would separate C from KU at any point along the arc I would think. Question is is there any issue of bandwidth or communications going through one of those boxes.

I just got my bud operational, and fired my ku back up as well. I need to be able to switch between a standard lnb ku motorized, and a G-box controlled c-band lnbf setup. I have a few receivers but am at the moment just concerned about hooking one up (coolsat 6k). I have 2 ecoda 22kHz...

I am in the process of setting up my c-band dish (7ft unimesh) and have a question about this lnbf. When setting the f/d ratio which surface do you go by to line up with the scale on the side? I assumed you go by the back edge where the set screw is. When setting the focal length do you go...

My first hobby is my trade, I design loudspeakers for the consumer and commercial market for a very large speaker company. That flows into my other hobbies which include home theater, car audio, and pretty much anything electronics related. Other honorable mentions include... motorcycles, on...

I did a random act of kindness.

Gotcha, ok so I was on the right track to begin with. Thanks

I see you are from chicago so that would mean my arm should point to the east as well(standing behind the dish) because I am in central indy. I guess I had it backwards as I thought the arm should point to the west and fully retracted the dish would be pointing towards the west coast as well...

I am about to setup my BUD for the first time and I am concerned on how to adjust the actuator arm. The actuator in question is a Superjack + HQ though I don't know if it is an 18 or 24 inch length but it came with a 7.5ft. unimesh. My question is how do I know where to set the arm all the way...

How can one tell definitively if a 922 or 920 has a bad unit ID#? I got one and the unit ID does not match what is on the back of the receiver. I thought they had to match and all started with triple zeros? in the menu mine starts out with 81-40D5 the label on the back of my unit starts...

I just got a free 7ft dish on saturday. The easiest way to take it down is first loosen the bolts holding the mount on the pole. once its free you will need another person to lift up and off the pole. After that dig around the pole until you see concrete, get a rope, chain etc. and hook it to...

Ok, I think I grasp the post #5 pretty easy, now how does one setup the receiver to know which "port" it is using on the switch? ? #2... Can I use a hose clamp and put my dbs lnb(for 119) beside my standard lnb on the stationary dish if I park it at 123W? If I read it correctly you can do...

I have read the switch FAQ but I am not sure what to do. I have one standard lnb on a motor, one standard lnb on a stationary dish, and one circular lnb for nasa/angel one. I want to hook this up to 2 receivers, I can settle for one right now if i need to. fortec star merc II coolsat 6000...

They seem to be good people. I told them about the missing lnb. I got a reply, shipping me an lnb out today.

I got mine all unboxed only to find there was no lnb in the box. I don't know if it was a mistake or not. :( I sent an email to them, hopefully they will respond and tell me they are sending one at no charge. I will say even without the lnb it was still a deal. I had one to use so not a big...

I debated on this for a few days. I just pulled the trigger as well. Hope it arrives before the weekend. :)