Search results for query: *

I've never bothered playing with the Display Settings but for TV System I use 1080P and Auto. The Auto really works well on the microHD unlike other devices I own. Regards, Steve

Wow, that website was definitely made by an Engineer. :p Steve

If you have an HD plasma scan this satellite right now...unless you are prone to epilepsy. I've never seen such a good video on my TV before. I'd like to know the bitrate if anybody can figure it out. Steve

Perhaps you did not set the motor up for some of your satellites. I'm just wrapping up scanning 24 ku satellites with the new firmware and it's going well. All I did was update the firmware, master reset, set video, add satellites, set satellites (USALS only, it's nice that they came pre-set...

I bought a new TV so I figured I'd check up on the microHD and it is in the Logitech website now! You search for it under Satellites but it will install under the PVR heading. The remote codes work well and you can access the special buttons (reg/green/sat, etc.) via the screen display on the...

False alarm, I neglected to see the UDF file available for download with the 2nd set of cable instructions. I uploaded that and had to use the Component cable and now the microHD is alive. Turns out the new files are left on 1080P and my CRT can only do 1080I so I'll have to keep that in mind...

I think I was able to sort things out in the end, I downloaded some different drivers and made communication. In the end I just used the power supply with the microHD to power the unit rather than try to use the 2nd USB cord for power. The 2nd cord probably would have worked instead of the...

Back again, Is it possible to upload the ABS file and not have it take? I tried really hard to get my old files off the machine but it was hanging regularly and after repeated attempts couldn't get past 28% so I gave up on that. The end result was that I uploaded the recent firmware and when...

Hi guys, What sort of functions should I see from the microHD when I'm plugged into it with the TTL cable? I plugged mine in the "right" way and nothing happened so I swapped the TX/RX and I get the green light to turn red a couple times but still no go. Any ideas what I need to do? My...

I bought one of those HDMI to Component cables off of ebay for 8 bucks or something and it doesn't work so don't bother. There must have been a lot of unhappy buyers because they have since put a note on the product saying your device must be able to be configured to use it...total scam. I'm...

Not to worry, I am now all-in for 5 bucks on a TTL cable which I was planning on getting at some point. :D I can live without DBS-S2 for a week while I'm busy building and setting up my new Home Theatre PC. As for the why I scanned useless channels, I am an Electrical Engineer who studied...

I have downloaded the files from my machine a couple times to look through them but I've never dared upload one. I am on the newest firmware. My setup is as follows: Stab HH90 motor using Usals QPH31 variant LNB Ku Linear sats scanned into Ku standard Ku positions (I scan them all in even if...

Grrr, I had scanned all the circular dishes in where the C band dishes are located (adjusted positions a bit) but didn't get anything of interest. So, it just so happened that I was still tuned into Dish Network when I turned off the "hearts" on the c band dishes in one shot. Now the receiver...

Hi guys, I finally obtained a 4x1 diseq switch for my QPH31 style LNB. I hooked up the Receiver Port to my Stab HH90 and the LNB ports to my 4 LNB ports. I used all 4 since I didn't get any water caps... Anyway, I can't get a signal using this thing. I played with the diseq options and...

I have a fake of the Invacom (Monster?) which works well. I can get everything listed on various sites but haven't played with the circular much as I don't have a switch yet. My LNBF has drifted off the mark a bit, it does scan a few Mhz off the listed #s but who knows how long it was sitting...

Hello, Would it be possible to dump the video memory between channel changes? This comes into play when you are trying to tune in a weak signal since you get past channels jumbled in with the new picture. Cheers, Steve

Thank you, I see they are in Rev 11. Steve

Are you running on Sinusoidal 120VAC or Square wave? Square wave inverters make clocks to crazy things. Steve

I have seen that I'm also getting multiple scans of the same channels at different frequencies with my super monster lnb (knock-off invacom 51). 97w is really bad, I get multiples of half the channels so this may be what you are experiencing. Steve

If it's not too late, could you add two satellites? I think SatMex5 and Anik F1R or F3 are missing from the Ku band. Squeezing them in your end would make it easier to scan things in in order. I've noticed that a few satellites have also got .0 when they should be .1 on the end as well...

Hi all, Has anybody programmed their Harmoy remote to match the MicroHD? I logged in and noticed that GeoSatPRO was on their list for Satellite boxes but no products came up. I typed in MicroHD hoping something would come up but it went directly to trying to read in all of the signals...

RPSSat will mail them out. They are tiny so it shouldn't cost much. Steve

I am not sure if this a bug or an intended feature but I found that the Multi-Satellite polarity setting is not global through the antenna settings like the "Detail Scan" is. I had 97W set to V only (I do not know why) and when I did a batch scan of the satellites I only ended up with about 150...

It works with the Western Digital 2.5" usb powered 1 terrabyte MY Passport. PN WDBABM0010BBK-00 It takes about 2 and a half minutes to load up a directory with 10700 items but only seems to display the first 1000. You'll need to split up your music if you want to use the microHD to play it...

I'm not sure if it's been mentioned previously but I'd like to see a bit more in the Blind Scan screen. It could show the Quality and Signal bars on the bottom so you can see how your alignment/dish size are managing. It could also show exactly which Frequencies it is analysing by having them...