Social Feed

DanthemanDawg

Last reply Oct 24, 2008 · posted in DIRECTV General Forum

HD Local Columbus Ohio Area

Having trouble getting in HD locals and some other HD channels in Columbus Ohio area. All other stations are coming in fine even digital locals, I keep getting searching for sat. signal on my HD local channels (ive also noticed that espn 206 didnt come in either). My HD channels came in fine about 3 months ago (just bought new HD tv and new receiver) thats y been 3 months since ive checked if hd was working and my warrnty is expired.

have a slimeline 5 dish
yes I have HD programming
Hr-20 HD silver receiver filter is on (had them send me a new one) and installed correctly.
6x8 multiswitch
sat settup (5 lnb multi sat)

what satellite and transponder can I check for signal strength????
I believe my dish needs adjusting if so what is the best way to adjust if im getting 80-90 signal strength on most satellites, but I did notice
Sat 101 Transponders all working 32 total
Sat 110 Transponders 3 total are working
Sat 119 Transponders 11 total are working
Sat 99a Transponders 14 total are working but getting all 0
SAt 99b Transponders 16 total are working but getting all 0
Sat 103a Transponders 7 total are working but getting all 0
Sat 103b Transponders 14 total are working but getting all 0

So are my locals have to be on 99 or 103, but which transponders can i check when I move the dish for signal strength??
And how should I adjust the dish, left right, up down, tilt up down, or angle??
I know this is going to be a pain in the as, any advice would be greatly appreciated.
And Thanks for your time in advanced.

15 Replies · 2762 views

Load Replies (15) Reply Legacy View

jcrandall

Oct 22, 2008

If you flat out can't get it, there is some good news.

DirecTV is reportedly changing the service call fee from $79 to $49.

At $49, it's a bargain considering they come to you.

Read the manual for the dish though, if you're comfortable with wrenches, patient, and have a helper that can read the screen to you, it's not very hard.

After you've done it once, it's much easier.

cocoon

Oct 23, 2008

Jason Crandall said:
If you flat out can't get it, there is some good news.

DirecTV is reportedly changing the service call fee from $79 to $49.

At $49, it's a bargain considering they come to you.

Is this only if you call DirecTV or can you call any D* dealer and get that price? It's a sticky situation for me as I am a "mover".

JAG72

Oct 23, 2008

cocoon said:
Is this only if you call DirecTV or can you call any D* dealer and get that price? It's a sticky situation for me as I am a "mover".

I don't 100% know but I would think that the pricing would be from Directv only. Dealers normally can charge different prices for their service.

cocoon

Oct 23, 2008

JAG72 said:
I don't 100% know but I would think that the pricing would be from Directv only. Dealers normally can charge different prices for their service.

That was my thought as well since DirecTV doesn't allow the customer to specify which dealer will be sent for the service call at least with the service plan.

Thanks for the signal strength screen caps my dish definitely needs to be adjusted. I had been looking for what good signal strength should be for several weeks unsuccessfully.

JAG72

Oct 24, 2008

cocoon said:
Thanks for the signal strength screen caps my dish definitely needs to be adjusted. I had been looking for what good signal strength should be for several weeks unsuccessfully.

Don't forget that many of them will be dependent on the area. The ones that I posted are what the Central Ohio signal strengths should look like. If you are in a different part of the country you may get signal from transponders that I show a 0 for and vise versa.

cocoon

Oct 24, 2008

JAG72 said:
Don't forget that many of them will be dependent on the area. The ones that I posted are what the Central Ohio signal strengths should look like. If you are in a different part of the country you may get signal from transponders that I show a 0 for and vise versa.

If by Central Ohio you mean the area that gets WBNS for CBS my signal strength should be very close to the numbers you posted even though I'm roughly 30 miles below that DMA. That is the DMA I moved to otherwise locals would be from another state and no HD locals.

JAG72

Oct 24, 2008

cocoon said:
If by Central Ohio you mean the area that gets WBNS for CBS my signal strength should be very close to the numbers you posted even though I'm roughly 30 miles below that DMA. That is the DMA I moved to otherwise locals would be from another state and no HD locals.

Maybe. It all depends on how large the spot beam for the local HD channels are. You may have a few that are a little lower than the readings posted.

View all replies (15)

Scott Greczkowski

Staff member HERE TO HELP YOU! Cutting Edge

Last reply 35 minutes ago · posted in The Chit Chat Club

Song Name Game Part 3!

Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne

Get it?

An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....

68658 Replies · 2680198 views

Load Replies (68658) Reply Legacy View

Reactions: c-spand

dishstaller

Today at 10:32 AM

I Wanna Talk About Me - Toby Keith

Reactions: RaiderPower

Bobby

Today at 10:51 AM

98.6 - Keith

harshness

Today at 11:25 AM

I'm Easy - Keith Carridine

Reactions: RaiderPower

gms49ers

Today at 11:41 AM

It's Easy - Boston

RaiderPower

35 minutes ago

Take It Easy On Me - Little River Band

Reactions: dishstaller

View all replies (68658)

reubenray

Last reply Today at 10:36 AM · posted in Computers and Gadgets

Laptop Shutting Off When On Battery?

Lately my eight year old Dell laptop has been shutting off even when I have a full battery. I have had to keep it plugged up all the time to keep this from happening. Any idea what is causing this? I replaced the battery about three years ago.

2 Replies · 44 views

Load Replies (2) Reply Legacy View

arlo

Today at 10:09 AM

A recalibration might be needed. Even if it shows full, the individual cells may have become unbalaced. And the BMS chip in the battery reports false information to the pc.
Try this. Start it up in the bios/uefi and leave it there until the battery dies and it shuts off.
It might just keep running longer than in Windows. Or run for a short while and shut off.
If it's the first case. Probably just needs a balancing. If the latter, the pack might just be dead.
Not throwing stones but perhaps just a cheaply constructed battery with substandard cells. Could be.

Patience. Keep restarting it in bios/uefi until it won't fire up anymore.
Then plug the charger in and let it complete a full charge. And see what happens. If it's better.
Do the same thing one more time. Run it until it dies dead-dead. Then just let it charge, pc shut off.
When charged, it might be better. It might not be.

There are bench jigs that read the actual BMS and override it to let a tech manually monitor and charge the separate packs. They can also reset any "time bombs" in it that cause an otherwise good pack to show bad.
Maybe Santa will be good to me some year.

You might just need a new battery. Maybe the PC power management chip is going. A Dell common thing.
Leaving a laptop plugged in with a full battery is known to reduce the life. Asus for one recommends that you don't leave the charger plugged in all of the time even when shut down. And setting Windows to charge the battery to 85% instead of 100% increases life.
That's all I got.

dishstaller

Today at 10:36 AM

arlo said:
That's all I got.

That was quite enough....I definitely learned something from your post. Thanks

TRG

Pub Member / Supporter

Last reply Today at 10:27 AM · posted in Computers and Gadgets

Starlink Router question

I set up a music server for my brother a few years ago. It's basically a small headless computer but it needs to have a DHCP IP address reserved for it in the router settings. This was easy to do in his DSL router. He's switching to Starlink now and I was wondering if these setting are easily accessible in the Starlink router. I'm pretty sure he will be getting the latest V5 router.

5 Replies · 283 views

Load Replies (5) Reply Legacy View

b4pjoe

Saturday at 2:12 PM

TRG said:
I set up a music server for my brother a few years ago. It's basically a small headless computer but it needs to have a DHCP IP address reserved for it in the router settings. This was easy to do in his DSL router. He's switching to Starlink now and I was wondering if these setting are easily accessible in the Starlink router. I'm pretty sure he will be getting the latest V5 router.

If you can't get into the router to reserve an IP address just don't use DHCP on the device that needs connected and assign it to a specific IP address in the network settings.

Reactions: harshness

HipKat

Saturday at 11:07 PM

TRG said:
I set up a music server for my brother a few years ago. It's basically a small headless computer but it needs to have a DHCP IP address reserved for it in the router settings. This was easy to do in his DSL router. He's switching to Starlink now and I was wondering if these setting are easily accessible in the Starlink router. I'm pretty sure he will be getting the latest V5 router.

They are not. Your best bet is to set up a third-party router, attached to the Starlink for your server, that you can get into, like a Linksys, etc

Reactions: Foxbat

Foxbat

Sunday at 12:44 AM

TRG said:
…it needs to have a DHCP IP address reserved for it in the router settings. This was easy to do in his DSL router. He's switching to Starlink now and I was wondering if these setting are easily accessible in the Starlink router. I'm pretty sure he will be getting the latest V5 router.

The Starlink V5 Install Kit I just got comes with the Mini Router. It is pretty limited in what it can do. For example, it can provide only one IP subnet at a time, no Guest Network, but it does support the pass-thru to a third-party Router. You can also split the Wi-Fi into separate 5 GHz & 2.4 GHz SSIDs to help some IoT devices that don't support 5 GHz bands to work.

The larger Starlink Router that still comes with the V4 Kit does support a Guest Network with separate IPv4 Subnet, but it's $120 from Starlink. And it still won't do DHCP Reservations.

harshness

Sunday at 11:46 AM

If you can restrict the DHCP address space to assign addresses to one end of the subnet (i.e. x.x.x.50+), you can manually assign the IP address on pretty much any operating system. This is a default behavior on several popular routers. As the Router Mini only supports 235 devices, I expect that's already done.

Another option is to use a router that supports PoE to power the antenna. This article discusses that option (under PoE Power heading):

Starlink V5 Is Here: What RVers Need to Know

Overview of the new Starlink V5 model along with comparison to the previous V4 model along with a recommended setup for mobile internet users.

mobilemusthave.com

Reactions: Foxbat

Foxbat

Today at 10:27 AM

Now that I've had the v5 kit with the Mini Router, it's not as bad as I first thought. Yes, no DHCP reservations, but you can set up multiple SSIDs that have separate IPv4 subnets, and like the big brother, you can select from 192.168.x.0/24 or 10.x.0.0/16 (where "x" is 1-4).

You can also split a subnet and have different SSIDs for the 5 GHz and 2.4 GHz channels to handle some IoT devices. I haven't discovered what subnet the 2nd NIC on the router assigns, I'm guessing it's the first subnet.

dishstaller

Pub Member / Supporter Lifetime Supporter

Last reply Today at 10:27 AM · posted in The Chit Chat Club

I think we could all use a laugh - Rodney Dangerfield on Carson

Good...simple humor. Enjoy

View: https://www.youtube.com/watch?v=E92AtfTLge4

View: https://www.youtube.com/watch?v=HJy0WnejlF4

2 Replies · 50 views

Load Replies (2) Reply Legacy View

Jimbo

Today at 12:37 AM

Not Rodney, but a laugh ...

View: https://www.youtube.com/shorts/WHEcmortfK0?feature=share

dishstaller

Today at 10:27 AM

Sorry for posting the wrong link. Just corrected it.

dishstaller

Pub Member / Supporter Lifetime Supporter

Last reply Today at 10:17 AM · posted in The Chit Chat Club

At least 64 dead in Spanish passenger train collision

Terrible tragedy. You would think that they would have safe guards in place that would prevent something like this from happening. I guess if you are going to ride in a passenger train it might be best to get a car near the rear.

At Least 64 Dead After Two High-Speed Trains Collide In Spain | ZeroHedge

ZeroHedge - On a long enough timeline, the survival rate for everyone drops to zero

www.zerohedge.com

2 Replies · 54 views

Load Replies (2) Reply Legacy View

Reactions: Jimbo

Jimbo

Yesterday at 11:24 AM

dishstaller said:
Terrible tragedy. You would think that they would have safe guards in place that would prevent something like this from happening. I guess if you are going to ride in a passenger train it might be best to get a car near the rear.

At Least 64 Dead After Two High-Speed Trains Collide In Spain | ZeroHedge

ZeroHedge - On a long enough timeline, the survival rate for everyone drops to zero

www.zerohedge.com

They will have to look at the switching sections to determine WHY 2 trains were on the same track ... at the same time.

dishstaller

Today at 10:17 AM

Thought this article might be of interest to some of you who might travel via train.

The safest seat to sit on in a train

Safety experts have shared top tips on train safety after a fatal railway crash in Spain killed 69 people, including where the safest place is in an emergency.

www.dailymail.com