In case someone else wants to know...
Following are the instructions that NetGear sent me to enable my VIP 722 to connect to the Internet via two bridged NetGear WG602 WAPs, just in case they may be of use to anyone else.
I'm just cutting and pasting... hope the formatting comes through OK.
I believe I followed the instructions, for the most part. I may have deviated on a couple items. Bottom line, it's working for us. We've had the VIP 722 connecting to the DISH mothership via the Internet for about four months now. The phone line to the unit is long since disconnected.
===================================
I understand that you want to configure the WG602v3 and WG602v4 in the repeating mode. We will be working to assist you in resolving the issue you described. Since we are doing this online it may require a few mail exchanges before we can resolve the issue. We will do our best to help resolve your case in the least possible time.
Please follow the steps to configure the wireless access points with the netgear router.
Step 1: Configuring access point 1(WG602v3)
Connect the access point 1(WG602v4) to the computer with a cable and then follow the steps.
1) Reset the access point to its default using the reset button as above. Turn on the access point & the computer.
2) Now assign a static IP address to the computer, which will be 192.168.0.200 & SM: 255.255.255.0 without default gateway.3) Assigning IP address:
a. Right click on 'My Network Places', go to 'Properties'.
b. Right click on local area connection (for wireless)', go to 'Properties'.
c. Under 'General tab', you will find the TCP/IP protocol.
d. Double click on it and assign the static IP address without default gateway. Click OK & Close. Restart the computer.
4) Now try to open the access point web page using http://192.168.0.231" target="_blank">
http://192.168.0.231 or http://192.168.0.227" target="_blank">
http://192.168.0.227 or http://192.168.0.228" target="_blank">
http://192.168.0.228 or http://192.168.0.229" target="_blank">
http://192.168.0.229 through Internet Explorer. By default, the username is admin, the password is password.
NOTE: The Username and Password are case sensitive.
5) Configure the wireless settings:
a) Change the name (ssid) to any name
b) SSID Broadcast: Enable
c) Select the appropriate region
d) Channel to 1 & mode: g & b. Click Apply.
6) Then click IP Settings under Setup and change the IP address as 192.168.0.50, subnet as 255.255.255.0 & Default gateway as 192.168.0.1(Select Disable for DHCP client)
7) Click on wireless bridging under advanced and select the option "Wireless Point-to-Point Bridging" and check the option "Enable Wireless Client Association" then enter the MAC address(wireless) of the second access point(WG602v4) and click on apply.
8) Connect the access point to the router with a cable.
Step 1: Configuring access point 2(WG602v4)
1) Reset the access point to its default using the reset button as above. Connect that computer to the access point using an Ethernet cable. Turn on the access point & the computer.
2) Now try to open the access point web page using http://192.168.0.231" target="_blank">
http://192.168.0.231 or http://192.168.0.227" target="_blank">
http://192.168.0.227 or http://192.168.0.228" target="_blank">
http://192.168.0.228 or http://192.168.0.229" target="_blank">
http://192.168.0.229 through Internet Explorer. By default, the username is admin, the password is password.
NOTE: The Username and Password are case sensitive.
3) Configure the wireless settings:
a) Change the name (ssid) to any name(the SSID should be the same as that of the access point 1)
b) SSID Broadcast: Enable
c) Select the appropriate region
d) Channel to 1 & mode: g & b. Click Apply.
4) Then click IP Settings under Setup and change the IP address as 192.168.0.60, subnet as 255.255.255.0 & Default gateway as 192.168.0.1(Select Disable for DHCP client)
5) Click on wireless bridging under advanced and select the option "Wireless Point-to-Point Bridging" and check the option "Enable Wireless Client Association" then enter the MAC address(wireless) of the first access point(WG602v3) and click on apply.
6) Disconnect the cable from the computer and try to connect to the access point through wireless and check the status.
We hope that the steps provided above would help resolve the problem/case. Please feel free to contact us again if you will require further assistance.