Social Feed

M
Last reply · posted in Free To Air (FTA) Discussion
Hello, I need some input on setting up the motor, the motor is a DMS SG-2100 and I'm wondering how to put the Elevation on the motor mount. Do I use the Latitude or the Elevation side.

The Latitude for me is 43.2 N Longitude 88.7
Motor Elevation is 43.2
Declination Angle is 6.6
Dish Elevation is 23

The Manual say to use the Latitude side which is how I have it set right now, but I'm thinking that I should use the Elevation which right now say 49.

The Dish is a 90cm dish and the receiver is a nfusion HD.

Azmith is 180.1 with mag 184.7 So what would be my true south bird, reading here I'm thinking its 89w or 87w sat's.

Any input will be helpful!

Musher
26 Replies · 3313 views
M
We try'ed that still the signal at 37%. I took the motor off and set the dish like a fixed one and try'ed for 89.0W and set the receiver too and still the signal at 37%.

On the birddog I did updated the firmware on saturday mornning and set it for what I was doing. We set the dish for elevation to what dish pointer said 40' for 89.0w and did skew the lnbfand still only 37% So it is the lnbf.
M
Update: well the new sat meter came and the lnbf is working fine that is up there and I do have a new Invacom Uni single NF 0.3dB LNBF sitting here. The problem is with the Receiver itself. The software is out of date, and there is NO update for it, did find a support web site for the nfusion receiver's and have sent them 5 emails and no emails back yet. Will kept everybody informed on what happens in the future.

So today I went to the Sadoun web site and bought a Fortec receiver and will be here on Friday and hope to get it in on Sunday.

I to thank everybody and I'm mean everybody who posted back with all the help, idea's, on the set-up "THANK YOU"

Musher
zamar23
I suggest you to exchange SNH-031 for QPH-031. Its Circular & Linear - the best for a motorized setup, and will complement your Nfusion HD very well. You better ask next time what equipment do you need before ordering it. You may want to look also at an extra Circular LNB with LO 10750 to complement Invacom - another good match for Nfusion HD to watch clear circular signals. Unless of course you have a separate 20" dish for Nfusion only.
M
Well today was the day, I went up on the roof to work on the system and found what the real problem was with it. First I hooked up the meter and peak the dish at 89.0W and tried and still no go. Second I did just move the hole thing dish & motor o 97.0W and tried again, still no go. But the dish was peak to 97w and had good ss of 85% and sq of 90% on the meter (SatHawk 5000).

Next it was onto the receiver's. First to Zamar23 I did check out those web-site's and most of them do you know what but the software I needed to upgrade my Nfusion HD was there so I upgraded it. It seems to be working fine. The Fortec Star Dynamic came on friday so I tried that one and but of them still no go.

Well the real problem I finally figured it out, The Meter said the dish & lnb was right on, the receiver's and both of them are working fine. The problem is the Motor! It would not let the signal pass through it and the motor stopped working. When I hooked up the coax cable that went into the motor right into the lnb and tried that both receiver's found all the channels at 97.0W. So right now I have the dish & motor pointed to 97.0W but no motor right now. Will work on the motor later.

Musher
zamar23
We try'ed that still the signal at 37%. I took the motor off and set the dish like a fixed one and try'ed for 89.0W and set the receiver too and still the signal at 37%.
It looks like your motor is OK, similar to your LNB and receiver, despite you bought extra ones. Reset and hard restart NFusion. Connect coax to motor, reset the motor by its hidden button. Drive east - west by motor buttons to see if it works. Drive to 0 by a button, reset again, drive to most east position - save, most west - save, drive to 0 by GoTo 0 command. Drive motor to 89W by USALS (after entering your exact coords in USALS) and pick the dish.
M
Zamar23, the motor is making a clicking sound and does not move so something is wrong with it. I did try the Reset and hard Reset on the Nfusion and did the reset button on the motor and use the button on the motor to move it East or West. The motor is only Compatible with DiSEqC 1.2 and not with USALS.

I did contact were I bought the system from and working on Getting the motor fixed. The motor now has some slop in it, the dish is mounted it wiggles back and forth a little bit but what I have right now I can live with it. The current SS on the Nfusion is 80-90% and SQ is 70-85%. Also if buy another motor I will get one that is both USALS & DiSEqC 1.2.

The mistake that I made was I should have bought the Pansat 9200 HD receiver and gotten everything else from Sadoun.

Musher
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in The Chit Chat Club
Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne


Get it?


An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
68510 Replies · 2671549 views
  • Like
Reactions: c-spand
H
I LIKE It LIKE THAT-The Dave Clark Five
  • Like
Reactions: ClarkGable
ClarkGable
Five O'Clock World - The Vogues
FTA4PA
Six O'Clock News - John Prine
Bobby
It's Five O'Clock Somewhere - Alan Jackson
harshness
Somewhere - Barbra Streisand
meStevo
Lifetime Supporter
Last reply · posted in The Chit Chat Club
Continuing the Kilauea thread in the Pub here. Perhaps the Iceland one too next time there's remarkable activity.

Currently there is precursory lava flowing into the crater, leading to the next episode that'll probably start within the next day.

You can see the pace of inflation / deflation here. It serves as the primary predictor for when the expect the eruptions, which coincide w/ inflation turning into significant deflation and last for several hours on average with significant fountaining.



View: https://youtu.be/Uecu2seh4b4


Wife and I like the AfarTV feeds, for the discussion along w/ them, though they're otherwise just mirrors of the official USGS feeds.


View: https://youtu.be/iws3rh5vLAQ
119 Replies · 3228 views
  • Like
Reactions: osu1991
Foxbat
​
  • Like
Reactions: RaiderPower
Foxbat
​
Foxbat
Oooo, quite the show now. All three vents have doming and overflows. The cone that built up around the North vent lost its upper quarter at 02:50 Oct 17 and is now spewing lava at a healthy rate. Don't know if I would say it's a fountain, but it's close.


IMG_1534.webp

edit: The USGS has called the official start of Episode 55 as starting at 03:19 HST Oct 17, 2026:

Alert Level: WATCH, Color Code: ORANGE 2026-10-17 13:43:56 UTC
HVO/USGS Volcanic Activity Notice

Volcano: Kilauea (VNUM #332010)

Current Volcano Alert Level: WATCH
Current Aviation Color Code: ORANGE

Issued: Saturday, October 17, 2026, 3:43 AM HST
Source: Hawaiian Volcano Observatory
Notice Number: 2026/H488
Location: N 19 deg 25 min W 155 deg 17 min
Elevation: 4091 ft (1247 m)
Area: Hawaii

Summary: Episode 55 of the ongoing Halemaʻumaʻu eruption began at 3:19 AM HST on October 17, 2026.

Volcanic Activity:
Episode 55 of lava fountaining in Halemaʻumaʻu began at the summit of Kīlauea began at 3:19 AM HST on October 17, 2026.

Fountain heights are relatively low at about 100-150 feet (30-45 m), and it is not clear whether this episode will evolve to the same heights as previous episodes. Continuous overflows from the vents began yesterday, October 16, just before 6 a.m. HST and transitioned into episode 55 fountains at 3:19 a.m. HST this morning. The current forecast is for winds are blowing from the north-northeast direction, which suggests that volcanic gas emissions and volcanic material may be distributed to the south-southwest direction from Halemaʻumaʻu.
  • All eruptive vents and lava flows are confined to Halemaʻumaʻu crater within Hawaiʻi Volcanoes National Park. Tephra fall from volcanic ash clouds is greatest within 3 miles (5 km) of the vents, lighter ash and Pele's Hair may stay suspended for large distances from the vents.
Foxbat
Kīlauea seems to be returning to the "normal" eruption script, impressive fountaining from the North Vent. For once, the V2 Cam has the best overall shot:
IMG_1535.webp
The lava flows have covered a good portion of the Halemaʻumaʻu crater floor.
BlackHitachi
Supporting Founder
Last reply · posted in Movie Talk
Since the Reds have there thread we should too!

Last watched Nine inch Nails
Next 3:10 to Yuma
5390 Replies · 510332 views
osu1991

View: https://youtu.be/9j3vxhzM8MY?is=Rs1cY1FQAiRWi87i


Come September (1961)
Rock Hudson and Gina Lollobrigida with Sandra Dee and Bobby Darin
  • Like
Reactions: dfergie
Y
1791758462355.webp


Simple, charming. Entire premise is quite silly but Cary Grant carries it across the line in good fashion.
T
Last: The Social Reckoning. Spoiler alert, they make Zuck look like a...
Foxbat
Since it was already "paid" for, I spent the two hours of my time watching the John Cena action movie on Apple TV, "Matchbox The Movie" even though the reviews were brutal. It was better than I expected, so I didn't feel like I had wasted an afternoon watching it. But it felt like another "Reacher"/"Neghley"/"Mission: Impossible"/"Fast & Furious" crash and blow stuff up with lots of automatic gunfire mixed in movie featuring covert CIA operatives.

I don't think we'll get a follow-up movie from this. I expect Mattel will have other toy lines to exploit.
Van
Van
Last reply · posted in What's Cooking?
Who says dinner or lunch has to be the only good meals of the day?

Honey butter grits with scrambled eggs and grilled boneless pork ribs on flakey biscuits washed down with cranberry juice.
6629 Replies · 379364 views
dfergie
Egg, sausage and cheese sandwich between bread toasted in butter in skillet... Chocolate milk.
  • Love
Reactions: TRG
dfergie
Egg, sausage and cheese sandwich between bread toasted in butter in skillet... Chocolate milk.
Add fresh hash browns, delete chocolate for milk with a slice of bacon.
  • Like
Reactions: Mr Tony and TRG
TRG
TRG
Bacon, eggs, hash browns and toast. Coffee.
  • Like
Reactions: Mr Tony and dfergie
TRG
TRG
Wound up at the Waffle House this morning. Got the two egg breakfast with coffee.

1622.webp
  • Like
Reactions: dfergie and Mr Tony
dfergie
Speaking of waffles, I'm going to put my mini waffle iron on stove so I'll remember to make waffles in the morning... Had some last week, been awhile.
dfergie
Dos cackleberrys over easy on top of 2 corned beef hash patties fried in skillet... Chocolate milk.
  • Like
Reactions: Bobby
dfergie
Staff member HERE TO HELP YOU!
Last reply · posted in What's Cooking?
Anyone making their own breakfast sausage? I've recently been trying different recipes, found some I like, some I've modified...
38 Replies · 3560 views
  • Like
Reactions: spongella
navychop
Bob Evans Sage.
R
Bob Evans Sage.
I will look, but I don't think I have seen it. Owen's breakfast sausage use to be favorite, but I can't find it anymore. Jimmy Dean's country mild is OK also when I can find it.
  • Like
Reactions: navychop
dfergie
Swaggerty's isn't too bad, sausage prices are lower per lb than making my own from pork butts right now so I've been buying JC Potter or Owen lately.
(Swaggerty's at Sam's is pre cut, I usually partially freeze the rolls and cut with my slicer and vacuum seal on parchment paper)
  • Like
Reactions: navychop
S
I will look, but I don't think I have seen it. Owen's breakfast sausage use to be favorite, but I can't find it anymore. Jimmy Dean's country mild is OK also when I can find it.
amazon maybe :what
S
I will look, but I don't think I have seen it. Owen's breakfast sausage use to be favorite, but I can't find it anymore. Jimmy Dean's country mild is OK also when I can find it.
owens on amazon is 54.99 for a 4 pk 16 oz a sausage. i feel that's kind of steep!!!
S
Swaggerty's isn't too bad, sausage prices are lower per lb than making my own from pork butts right now so I've been buying JC Potter or Owen lately.
(Swaggerty's at Sam's is pre cut, I usually partially freeze the rolls and cut with my slicer and vacuum seal on parchment paper)
id'e rather make my own vs store bought.
  • Like
Reactions: dfergie
R
owens on amazon is 54.99 for a 4 pk 16 oz a sausage. i feel that's kind of steep!!!
Especially when I can get a two pound roll of Jimmy Dean from Sam's Club for $7.38.
dfergie
They run Owens at $3.99 for lb and $7.99 a couple times a month at some grocery stores here, I actually was wrong, just checked a pork sirloin roast it was $1.99 a lb. (cooked it yesterday so pack was in trash)
  • Like
Reactions: reubenray
TheRatPatrol
Last reply · posted in TV Shows
Anyone else watch this show? Any guesses as to what was in the box Gibbs gave to Abby that was on her desk? It look liked it was glowing.

I also heard that someone was leaving the show at the end of this season. Any guesses as to who thats going to be?
2134 Replies · 214759 views
Jimbo

Howard ...
You don't like Tony, or Tony as the Director (he's only been there for 30 seconds now) or you don't like NCIS ?
  • Like
Reactions: Howard Simmons
Howard Simmons
Howard ...
You don't like Tony, or Tony as the Director (he's only been there for 30 seconds now) or you don't like NCIS ?
Tony as the director.🙄
Jimbo
Tony as the director.🙄
Would you rather have LaRoche ???
  • Like
Reactions: Howard Simmons
dfergie
I liked this episode and a toned down Tony...
  • Like
Reactions: Jimbo
Howard Simmons
Would you rather have LaRoche ???
No. Bring in someone new.🤔 Tony is not serious enough for me. Parker is too close to the team and Tim is too young to take over IMO.
Jimbo
No. Bring in someone new.🤔 Tony is not serious enough for me. Parker is too close to the team and Tim is too young to take over IMO.
I don't think Tim and Tony are that far apart in Age ...

Remember what Tony said to Tim when they first got back together ...
Tony said: I am the New Tony, Tim .... (something to that effect)

Tony has changed, he's been running his Security Business ... I'm sure he has grown up.

Give it time ... your judging the New Tony from the old Tony.

It sounds like Tim won't be around the Team much longer either.
KAB
KAB
I wonder it they will show the teased meeting (in Origins) with Tony and Gibbs.
  • Like
Reactions: reubenray
Jimbo
I wonder it they will show the teased meeting (in Origins) with Tony and Gibbs.
I'm curious how they are going to implement Tony into Origins (If they do) ...
Tony was introduced to Gibbs and the team, on NCIS, which makes it the Mothership side of things, he worked in Baltimore prior to NCIS, NO mention when they met that anyone had known one another ...