Social Feed

S
Last reply · posted in DIRECTV General Forum
I've been on uverse. But now want to switch. With uverse I've been using cat5 to reach my 3 tv's. 2 also have coax, which I've connected to an antenna for OTA. The 3rd only has cat5.

If I switch to DTV, must I have coax to each tv? Can the DTV STB's use cat5? While uverse stinks, it's great to be able to switch to OTA when available.

sean
26 Replies · 15698 views
S
OK, went to the weaknees site to look at some wiring diagrams. So I get that you connect the OTA feed and the DTV feed into the SWM8. Then SWM8 to Power Inserter.

Now I get confused. Let's assume I only have one HD-DVR. Do I just connect IRD from the Power Inserter into the HD-DVR? Will the OTA channels show up separately?

Or do I run connect the IRD to a "diplexer" which gives me two cables - one for the ATSC tuner on the TV and one for the receiver? Then to watch OTA, I'd do like I do now and switch sources on the TV.

How much of this stuff does DTV provide? Or is it all after-market?

sean
J
in fact diplexers will not work on the swim side. as it requires a 2mhz fsk channel which the diplexer will cripple. the ota is for legacy side only
S
I must be dense.

I have the cable coming from the IRD port of the Power Inserter (located in the basement) into the living room.

In the living room I connect that cable to a diplexer which gives me two cables. One cable I connect to the HD-DVR. The other cable I connect

a. to the cable-in ATSC tuner on the TV, or

b. to the AM-21 which I've bought. The AM-21 connects to the HD-DVR.

Why would I choose b ?

sean
jtwex
in fact diplexers will not work on the swim side. as it requires a 2mhz fsk channel which the diplexer will cripple. the ota is for legacy side only


That's just rubbish. They make SWM diplexers that carry a range of 950mhz to 2150mhz that are designed for the SWM splitter. Not only am I using that very setup right now but you can go to Weaknees & see that they carry SWM diplexers to go right along with your other SWM technology. They ABSOLUTLEY work on the SWM side!
jtwex
I must be dense.

I have the cable coming from the IRD port of the Power Inserter (located in the basement) into the living room.

In the living room I connect that cable to a diplexer which gives me two cables. One cable I connect to the HD-DVR. The other cable I connect

a. to the cable-in ATSC tuner on the TV, or

b. to the AM-21 which I've bought. The AM-21 connects to the HD-DVR.

Why would I choose b ?

sean

You choose "B" so the DTV guide incorporates all the channels, You can record those channels if you have a DVR & you don't have to change inputs to watch OTA locals....it's a no brainer.
harshness
How much of this stuff does DTV provide? Or is it all after-market?
As I said earlier, DIRECTV won't give you much that will help.

My understanding is that if you go for all SWiM capable receivers, they'll install the them and a SWM dish with power inserter. No joy for using CAT5 cabling nor diplexing.

DISH can do everything but the CAT5 but will charge extra for the diplexers and splitter required for OTA.

When all is said and done, it may prove cheaper to fish more cable.
S
So for three locations, I can get DTV to install an SWM with a power inserter ( so I don't need an SWM 8?) in the basement. I can connect the OTA feed to the SWM in the basement.

Doesn't DTV install a splitter for the 3 existing room drops?

At each room location I'll need (from weaknees):

DIRECTV-Approved Diplexer for SWM
DIRECTV-approved diplexer for SWM. Splits satellite signal from CATV and off-air signals.
$12.00 - FREE GROUND SHIPPING

and an AM21.

Am I getting closer?

sean
jtwex
So for three locations, I can get DTV to install an SWM with a power inserter ( so I don't need an SWM 8?) in the basement. I can connect the OTA feed to the SWM in the basement.

Doesn't DTV install a splitter for the 3 existing room drops?

At each room location I'll need (from weaknees):

DIRECTV-Approved Diplexer for SWM
DIRECTV-approved diplexer for SWM. Splits satellite signal from CATV and off-air signals.
$12.00 - FREE GROUND SHIPPING

and an AM21.

Am I getting closer?

sean
Yea, you're getting closer & pretty much on the mark. It sounds like your having D install the SWM 3LNB which is a slightly different configuration than already having an AT/U9 with 4 coax outputs that go into the SWM8. I don't have the schematics for the SWM-LNB so I'm not 100% sure how or where they diplex in your OTA feed but it would have to be upstream of the splitter or you would only be getting your OTA's off of the good coaxial cable. If you get a great installer who's done some of these things it should go smoothly; you get the deer in the headlights tech & you'll have to reschedule. If you weren't getting the SWM dish from DTV it sounds like you could do all of this yourself with the help of this board. I followed the directions to the letter & listened to the pros here for help (one emailed me the full schematics) & the Receivers all switched over to SWM without a hitch. It also gave me a chance to replace & redirect all the old coax (besides the buried stuff) just the way I like it instead of their install. Bottom line, you're on the right path & you may encounter a hitch or two along the way but in the end you'll love it. As an aside (& keep in mind I have plenty of OTA signal with a preamp/distribution amp setup) you can use a normal dipler on the OTA coax that comes from the SWM diplexer & feed OTA to both the AM-21 & you're TV. I know you lose a little signal every time you make a splice or use one of these connections but the loss is minimal if you have amplified OTA feeds. Should your OTA stations start to fade in & out or checkerboard themselves you'll just have to remove the second diplexer because you don't have enough signal. If it works you have OTA on your receivers as well as your TV should you ever want to use that input to watch locals or your box goes bad.
M
Last reply · posted in Over the Air Television By RabbitEars.Info
Interesting article about the work being done to develope an ATSC 3 converter box. Yes it does mention affordable.
1 Replies · 8 views
Scott Greczkowski
Hopefully they are better then the current highly insecure junk boxes that are out now.
meStevo
Lifetime Supporter
Last reply · posted in The Sports Section
Schedule drops tomorrow. Mandatory mini camps in June. Hall of Fame game August 6th.
118 Replies · 1881 views
  • Like
Reactions: Jimbo and dfergie
Foxbat
I guess even the patience of us laid-back Hoosiers has its limits:
rvvaquero
I guess even the patience of us laid-back Hoosiers has its limits:
Be nice to see a Cowboy headline like that.
M
I guess even the patience of us laid-back Hoosiers has its limits:

Can we expect to see a new coach if we say "pretty please?"
  • Like
Reactions: Foxbat
Foxbat
Jeeez, Week 6, no lead is safe…
  • Like
Reactions: Mike0616
b4pjoe
Be nice to see a Cowboy headline like that.
Yes the Cowboys owner needs to fire the general manager (himself), co-owner, Chief Operating Officer (COO), Executive Vice President, Director of Player Personnel, and President of AT&T Stadium (his son) and then he should jump off of a cliff. Only then can they recover.
rvvaquero
Jerry Jones and Jimmy Johnson had an argument about who was responsible for the dynasty building of the early 90's Cowboys.

The rest of us figured it out in about 3 years, Jerry has had over 30 years but still can't admit it. It's all he lives for, to show everyone he can put together a winner. I don't think he can. His kids only know what he taught them.
  • Like
Reactions: b4pjoe
dfergie
Staff member HERE TO HELP YOU!
Last reply · posted in The Chit Chat Club
Stumbled across this ... http://www.gaspricewatch.com/USGas_ZipSearch.asp
I found no local prices, although it did show stations at my location...
Added these to this post...
USA National Gas Temperature Map
State By State Gasoline Taxes
Gas Buddy

Ethanol Free Stations

5554 Replies · 460832 views
Bobby
Regular$5.999​
Premium$6.399​
Diesel$7.999​
at Costco, Rohnert Park.​
  • Like
Reactions: harshness
dishstaller
Regular$5.999​
Premium$6.399​
Odd that out there, Prem is only 40 cents higher. Here it's a full dollar more.

Last night it was about $4.17 gas, $6,19 diesel.
harshness
Odd that out there, Prem is only 40 cents higher. Here it's a full dollar more.
On the West Coast, a 40-cent differential is common. It used to be 30 cents before the prices rose above $3.

A "full dollar more" sounds like it may be boat gas (non-alcoholic), which is a whole different discussion.
  • Like
Reactions: Foxbat
Foxbat
Here in Indiana, the difference between Regular and Premium is usually a dollar, but some charge even more:
1792374072446.webp
  • Like
Reactions: dishstaller
dishstaller
A "full dollar more" sounds like it may be boat gas (non-alcoholic),
Both non-ethanol and prem run about the same....buck more. When we were up in TN it was a buck more up there as well.
harshness
In Oregon, our premium boat gas is about a dollar more than our corn premium. Several stations only offer the non-corn premium grade.
Bobby
Regular$5.899​
Premium$6.299​
Diesel$7.999​
at Costco, Rohnert Park.​
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in The Chit Chat Club
Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne


Get it?


An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
68542 Replies · 2673896 views
  • Like
Reactions: c-spand
H
LITTLE Willy-Sweet
  • Like
Reactions: ClarkGable
ClarkGable
Little Deuce Coupe - The Beach Boys
  • Like
Reactions: gms49ers
gms49ers
The Boys of Summer - Don Henley
FTA4PA
Summer In The City - The Lovin' Spoonful
  • Like
Reactions: gms49ers
Bobby
Gonna Send You Back To Georgia (A City Slick) - Timmy Shaw
T
Last reply · posted in C-BAND Satellite Discussion
Howdy folks long time no write.

Issue(s): Horizontal transponders (esp. Weigel mux) breakup/mosaic/sputtering audio, JTV less so (but received perfectly up until a month or so ago.
Vertical is fine (Daystar). Up until recently couldn't even get any signal on Weigel Mux but JTV was perfect.

What I did to improve things: A slight westward move improved reception but only slightly (approx 72 on the micro HD, sorry no dB to post). I removed the 3-way C-Band splitter and used a 2-way to get a 1-2 db signal gain ( the power port goes to the Startrak - the micro HD doesn't have enough juice ! (1st clue) even after swapping the switching power supply it came with with a heftier linear 12 V supply (less RFI too !).
I have had issues with the uHD before signal breaking up that a reboot would clear up (clue #2 = dying tuner?) - FYI, I reinforced the IF input and removed all flux from the pcb completely with a Flux Removal Pen (MG Chemicals Cat No. 4140-P) which definitely makes a huge difference.

I went outside and pushed and pulled reflector slightly and no improvement. Pole (actually tower in yard - the neighbours love me..NOT) is plumb, checked with carpenters level. Dish was last peaked in 2017 or so, after overhauling 24" Von Weise, new Acme, fresh grease, etc. Focal length, f/d ratio etc meticulously adjusted. One panel has a tear so planning to repair that this weekend when my cousin comes over ( to help me out (old guy here) forecast calls for sunshine.

What has changed: My utility company has installed new high tension line poles (one smack dab in the middle of 101°W target! But they put it in last year and reception (of JTV (HOR) at least) was fine, BUT when they came out to transfer the wires over this year from the old (sawed in half) pole that's about when the troubles started (coincidence?), but again Daystar (VER) was fine. I always had this pole in the light of sight of 101° before with no issues. (fyi my zenith sat 74° is unobstucted, but can't test)

In the meantime Weigel mux is trying to break in MOSTLY in LATE at night (less cell usage?) (audio not video except for a frame here or there) so don't know what has changed with this mux which suddenly "woke up". I have never had to fuss with dish moves on this satellite ( the slightest move +/- motor clicks loses lock, wheres normally on C-band I can go significantly wider east or west and still have a strong signal ( have these gone "spot beam" or narrower somehow and what is the slight difference in Az listed on Lyngsat to 100.9° affect things ( isn't that the declination i.e. requiring a tweak of declination?).

Long story short (too late, ha), if I had another DVB-S2 box to try and / or a newer more stable PLL lnb ( I have been meaning to upgrade many a time but never got arround to it) I could determine if it's my antiquated receiving equipment, or my dish/feed alignment ( doubtful as it tracks everything from 55 °W to 133 ° W nicely.) or the dreaded 5G! (BUT only on HOR and not VER?).
I read another post where the OP (with his smaller 7.5 footer) played around with the illumination to peak desired transponder and reduce qrm on interfering/ stronger xpndrs (even on 103° W). So will play with that too - and cut away the RG-6 a and pull up a fresh section with new PPC and coax Seal. Open the throat cap see if any cobwebs are there and check servo operation (also changed in last maintence 10 years ago).

Finally, this will probably be the last chance I get to play with the BUD from the looks of it (providers leaving, auctioning off rest of spectrum imminent above 4.0 Ghz, and to keep the peace with neighbours so it would be nice to have that mux back for the long, cold and dark winters to comfort this old man before I call it quits and buy a VHF/UHF/FM Yagi and get MeTV, H&I from my Vermont local stations (checked at a friends today and they come in nicely - except ABC) .
Only one guy in town (Montreal) I may be able to get a receiver or PLL lnb from to try (RPS Sat) so hopefully with elimnate that as a possible culprit. Be nice to pick up a cheap or used PLL lnb to try w/o 5G BPF (money is tight )

Like others I couldn't care less about "tv" (well maybe just a liitle or a lot) it's the challenge that excites me , I can get MeTV other ways OTA (no pirate crap).

So what do you guys (and gals) think ?. p.s. I don't have a spectrum analyzer and there are def/ cell towers nearby (half a Km or so away).
Oh and time permitting will hammer out dings too and wire damaged mesh on one section for an extra dB or two. Hesitate to touch Declination, Elevation and pole mount but will play around with those a little too... Why is this mux for finicky suddenly ?(8psk, 5/6 fec, beamwidthetc.. man wish they went back to VER I think everthing would be fine! For the engineers out here does 5G QRM affect one poliarization (HOR) more than another (VER)? I understand the strong interference swamps out the input mixer/local oscilator in the hapless old C-band lnb (I think it at time affect KU too esp. LPB on 101°W KU - incidentally thos were weak or "gone' but are back almost at the time MeTV improved..hmm Terrestrial interference?

Any thoughts or suggestions ( cheap or free solutions please) greatly appreciated. Cheers.

p.p.s. Micro HD can't display Decades and Toons but records them fine so I can watch on another box/media player (Ali chip set issue). Another reason to upgrade.

Anybody interested in a nice C/KU system free ? (for next Spring/Summer 2027)

[Sami 10' mesh, Corotor II+, Eagle Aspen (very old) C-band lnb, Norsat Ku lnb, Channel Master C/Ku (H/V) switch, Startrak 400 Analog receiver w/ motor control, Geosat uHD DVD-S2, CW600S for Mpeg-2]
10 Replies · 385 views
cyberham
With the microHD connected this afternoon and tuned to the Weigel mux, I can receive the mux well.

My conclusion is that the sensitivity of the receivers in descending order of sensitivity is as follows:
  • V9 Prime (best)
  • microHD
  • Edision osmio4k+
Either the V9 or the microHD could be used to watch Weigel but the Edision really could not with my given dish situation, at least during the daytime. At night, the signal is stronger here and then maybe the Edision could be used.

Weigel mux.webp
Titanium
What is the SNR readings for these transponders? Is the signal breaking up due to low SNR or interference?

Did you inspect the feedhorn throat and wave guide for wasp nest or other blockage? Good SNR with frequent drops in decoding ( loss of SQ readings) could indicate interference from 5G.
T
Appreciate you checking. I should be picking these up with the tenner so still not done tuning up the bud - fell off ladder last week and hit my head!

Started over from scratch, N/S alignment, El/Decl extreme West sat, played with feed f/d checking everything and getting nice signals but still 101 west is PIA. New lnb was defective and returned it. My old one is fine but would have liked to A/B with a better lnb.

Thought it was the servo there because I was out and set everything up by the dish and flipping to HOR made a strange noise -BUT ONLY on 101 W ! All other sats skew is fine..hmm ( I have the skew almost perfect, use "Arrow" template on Zenith Sat (well nothing on 74 W to check with but Nimiq 5 at 72.6 W is closest and luckily picking up R- Pol channel from Canada to test with. Anyway picking up a new servo to try (the obvious polarity culprit).

Q. Back in the day PAS9 (74 W) was used but now I have to use closest zenith sat (Nimiq 5). I can't perfectly peak on that one which is 1 degree off (N/S alignment error). I used my trusty Brunton compass and even true noon shadow off pole to hit south.

I did have to peak extreme west by rotating mount ever so slighty so tracking extreme pretty good, but top and middle can use an elevation tweak (esp. Ku) to bring them back to where they were. No fun as the weather has been miserable and still dizzy from fall.

Oh and the Freesat V8 is crap (the tuner pixelates when the uHD is solid!) but love that SCART connector for S-Video out ! (I record to my Pio DVR and burn to DVD classic tv shows).

Stay tuned

With the microHD connected this afternoon and tuned to the Weigel mux, I can receive the mux well.
T
Did you inspect the feedhorn throat and wave guide for wasp nest or other blockage? Good SNR with frequent drops in decoding ( loss of SQ readings) could indicate interference from 5G.

Thanks for chiming in here. No wasps (or hornets nests) but good suggestion.

I am getting 70 and over Quality on uHD which is good but as you say the signal drops out (70 to 0 ) occasionally and much worse by day (even JTV which I used to get solid is a mess in the day. Again Daystar (VER) is fine but still not what it used to be.

I will will either have to get a BPF or go VHF/UHF for these channels but not giving up just yet!

p.s. Isn't there something between your feedhorn/lnbf BPF model and Norsat's 1500$ BPF and 5G filtering lnb's? Heck almost ready for a diy (reverse engineer) job here (microwave BPF hack) Ah where is Radio Electronics when you need it! If it wasn't for losing Ku I'd buy your lnbf in a heartbeat! Are these hard to add Ku to?
Titanium
Our LNBFs are integrated with the feedhorn and no KU option. Maybe install an inline waveguide BPF such as:

www.ebay.com/itm/158077455896
www.ebay.com/itm/960059145385
www.ebay.com/itm/158007483799
B
Howdy folks long time no write.

Issue(s): Horizontal transponders (esp. Weigel mux) breakup/mosaic/sputtering audio, JTV less so (but received perfectly up until a month or so ago.
Vertical is fine (Daystar). Up until recently couldn't even get any signal on Weigel Mux but JTV was perfect.

What I did to improve things: A slight westward move improved reception but only slightly (approx 72 on the micro HD, sorry no dB to post). I removed the 3-way C-Band splitter and used a 2-way to get a 1-2 db signal gain ( the power port goes to the Startrak - the micro HD doesn't have enough juice ! (1st clue) even after swapping the switching power supply it came with with a heftier linear 12 V supply (less RFI too !).
I have had issues with the uHD before signal breaking up that a reboot would clear up (clue #2 = dying tuner?) - FYI, I reinforced the IF input and removed all flux from the pcb completely with a Flux Removal Pen (MG Chemicals Cat No. 4140-P) which definitely makes a huge difference.

I went outside and pushed and pulled reflector slightly and no improvement. Pole (actually tower in yard - the neighbours love me..NOT) is plumb, checked with carpenters level. Dish was last peaked in 2017 or so, after overhauling 24" Von Weise, new Acme, fresh grease, etc. Focal length, f/d ratio etc meticulously adjusted. One panel has a tear so planning to repair that this weekend when my cousin comes over ( to help me out (old guy here) forecast calls for sunshine.

What has changed: My utility company has installed new high tension line poles (one smack dab in the middle of 101°W target! But they put it in last year and reception (of JTV (HOR) at least) was fine, BUT when they came out to transfer the wires over this year from the old (sawed in half) pole that's about when the troubles started (coincidence?), but again Daystar (VER) was fine. I always had this pole in the light of sight of 101° before with no issues. (fyi my zenith sat 74° is unobstucted, but can't test)

In the meantime Weigel mux is trying to break in MOSTLY in LATE at night (less cell usage?) (audio not video except for a frame here or there) so don't know what has changed with this mux which suddenly "woke up". I have never had to fuss with dish moves on this satellite ( the slightest move +/- motor clicks loses lock, wheres normally on C-band I can go significantly wider east or west and still have a strong signal ( have these gone "spot beam" or narrower somehow and what is the slight difference in Az listed on Lyngsat to 100.9° affect things ( isn't that the declination i.e. requiring a tweak of declination?).

Long story short (too late, ha), if I had another DVB-S2 box to try and / or a newer more stable PLL lnb ( I have been meaning to upgrade many a time but never got arround to it) I could determine if it's my antiquated receiving equipment, or my dish/feed alignment ( doubtful as it tracks everything from 55 °W to 133 ° W nicely.) or the dreaded 5G! (BUT only on HOR and not VER?).
I read another post where the OP (with his smaller 7.5 footer) played around with the illumination to peak desired transponder and reduce qrm on interfering/ stronger xpndrs (even on 103° W). So will play with that too - and cut away the RG-6 a and pull up a fresh section with new PPC and coax Seal. Open the throat cap see if any cobwebs are there and check servo operation (also changed in last maintence 10 years ago).

Finally, this will probably be the last chance I get to play with the BUD from the looks of it (providers leaving, auctioning off rest of spectrum imminent above 4.0 Ghz, and to keep the peace with neighbours so it would be nice to have that mux back for the long, cold and dark winters to comfort this old man before I call it quits and buy a VHF/UHF/FM Yagi and get MeTV, H&I from my Vermont local stations (checked at a friends today and they come in nicely - except ABC) .
Only one guy in town (Montreal) I may be able to get a receiver or PLL lnb from to try (RPS Sat) so hopefully with elimnate that as a possible culprit. Be nice to pick up a cheap or used PLL lnb to try w/o 5G BPF (money is tight )

Like others I couldn't care less about "tv" (well maybe just a liitle or a lot) it's the challenge that excites me , I can get MeTV other ways OTA (no pirate crap).

So what do you guys (and gals) think ?. p.s. I don't have a spectrum analyzer and there are def/ cell towers nearby (half a Km or so away).
Oh and time permitting will hammer out dings too and wire damaged mesh on one section for an extra dB or two. Hesitate to touch Declination, Elevation and pole mount but will play around with those a little too... Why is this mux for finicky suddenly ?(8psk, 5/6 fec, beamwidthetc.. man wish they went back to VER I think everthing would be fine! For the engineers out here does 5G QRM affect one poliarization (HOR) more than another (VER)? I understand the strong interference swamps out the input mixer/local oscilator in the hapless old C-band lnb (I think it at time affect KU too esp. LPB on 101°W KU - incidentally thos were weak or "gone' but are back almost at the time MeTV improved..hmm Terrestrial interference?

Any thoughts or suggestions ( cheap or free solutions please) greatly appreciated. Cheers.

p.p.s. Micro HD can't display Decades and Toons but records them fine so I can watch on another box/media player (Ali chip set issue). Another reason to upgrade.

Anybody interested in a nice C/KU system free ? (for next Spring/Summer 2027)

[Sami 10' mesh, Corotor II+, Eagle Aspen (very old) C-band lnb, Norsat Ku lnb, Channel Master C/Ku (H/V) switch, Startrak 400 Analog receiver w/ motor control, Geosat uHD DVD-S2, CW600S for Mpeg-2]
I had the EXACT same problem happen to me with 101w, MeTV mux (Weigel). Working great when about 3 weeks ago I started to get the pixelating, especially at night. Sometimes Jewelry TV would also do it, sometimes not. Tweaked my dish. I have a Titanium 240 feed with the 5G filter 4.0-4.2 band pass. Every other satellite is working fine. Something on their end for sure. Power reduction? My signal seems fine like always. Running a Winegard 8.5 ft dish using a GT Media UHD V8. I'm sure my receiver isn't maybe sensitive enough for lower signal levels. Frustrating here too. I'm in the Canton, Ohio area. Thanks!
arlo
To me it looks like all of the intelligent things to diagnose the problem 'on the cheap' are being done.
I have my own thoughts of lnbf's using an external filter between the feed and coax. It would be cool to see what Brian could add.
Do his units have the filter before the actual LNA chip in the circuit? In other words, signal is focused at the lnbf throat. The probes for h & v polarity send the signal to.......filtering......then to the lna IC......
Or probes, lna, then filtering. Makes sense to trap the bad stuff before amplification to me.

On the cheap sometimes leaves questions. Enosat and El Bandido both use dvb-s pci cards and TBS USB receivers.
With those, and software. Signal analysis becomes sort of easy. Or tapping into your coax with a dc pass splitter, decoupling capacitor, and using a spectrum analyzer. Tuning across the LO band. Finding signal spikes. Digging deep.

Still making my decision on a (most probably) TBS PCIe tuner card. But I have tapped into my coax with my ancient but quite impressive HP spectrum analyzer and tinysa.
I don't have 5G interference so far that I know of. But have my suspects because I'm only able to snag signal from 131W in the winter when the leaves drop. But out of curiosity do scan it in the fall. And seem to be getting a signal that 'shouldn't' be there and a scan shows no channels. Far as I got.

An idea pops up to rig up an LNBF on a stick. Along with the tinysa and power supply and do some rogue signal searches. War Driving, of sorts. But. I wouldn't think that a chinabox, firmware based receiver would be of much help.
From what I see scanning across the frequency band. 5G cell transmission is always on and is very wide spectrum.
Whether anyone is actually using talking, texting, watching stupid human tricks on YouTube Makes no difference. The RF is there. So why would a C Band setup come and go? And what if you dumped the corotor and went modern voltage controlled polarity?

Another thought. Since you've learned the optimal position to place the scalar to illuminate out to the dish rim. And peaked the feed. There's most of a roll of aluminum flashing out in my garage that would most definitely wrap around my dish perimeter. That and a bag of large binder clips from the office supply. wally world. Ideas?
T
Last reply · posted in DISH Network Support Forum
I thought I would come here and find lots of complaints about the update to the dish anywhere mobile app, but am not seeing any. It used to look just like the desktop webpage. Now you can no longer filter by sports channels or movie channels. Plus that they made it look like a big button telephone and you see fewer channels in the screen which requires more scrolling. Yes I realize you can look at sports then select which sport you want to look at, I just liked being able to see all sporting events in the guide with all other channels being filtered out. Am I alone in the wilderness on this?
8 Replies · 292 views
  • Like
Reactions: dishstaller
dishdude
I like the new look, it's a lot cleaner. I'm using it on one of those Onn streaming devices when I travel.
  • Like
Reactions: charlesrshell
T
I like the new look, it's a lot cleaner. I'm using it on one of those Onn streaming devices when I travel.
Yes a lot cleaner, glossier, and less functional. Someone trying to justify why they are making a big salary. "See look shiny"
  • Like
Reactions: charlesrshell
navychop
"Big salary." Charlie. "?Big?"
Tampa8
Seems in some ways better. Nicer layout, as others said maybe cleaner. Moving ahead in the guide is better.
S
I thought I would come here and find lots of complaints about the update to the dish anywhere mobile app, but am not seeing any. It used to look just like the desktop webpage. Now you can no longer filter by sports channels or movie channels. Plus that they made it look like a big button telephone and you see fewer channels in the screen which requires more scrolling. Yes I realize you can look at sports then select which sport you want to look at, I just liked being able to see all sporting events in the guide with all other channels being filtered out. Am I alone in the wilderness on this?
I think most are using it on a firestick or other device as an extra receiver, rather than their phone. Just a guess based on how I use it. 99% thru my firestick, 1% phone.
  • Like
Reactions: llokey
dfergie
Staff member HERE TO HELP YOU!
Last reply · posted in TV Shows
Stargate SG-1 cancelled, Atlantis renewed
clear.gif

Monday - August 21, 2006 | by Darren Sumner
clear.gif

The future of Stargate is in question today, as SCI FI Channel has cancelled the long-running Stargate SG-1, Multichannel News reported today and a GateWorld source has confirmed. The news regrettably follows the airing of the show's milestone two-hundredth episode on Friday.

Stargate Atlantis, meanwhile, has been renewed for a fourth season, with the network hoping to see that the spin-off series can stand alone, according to a source.
Source Gateworld
2034 Replies · 184192 views
R
I have gotten back into watching SG-1 and I have recorded most of the episodes to binge watch. What episodes are about the Antarctic or was this a movie? Also where could I watch the SG-1 movies?
osu1991
long_time_Dish
I have gotten back into watching SG-1 and I have recorded most of the episodes to binge watch. What episodes are about the Antarctic or was this a movie? Also where could I watch the SG-1 movies?
Well, there are a couple involving the Antarctic. "Solitudes", S1 E17 (one of my favorites), Then, "Lost City', S7 E21 and E22. Then, in the SGA pilot, "Rising", S1 E1 and E2, it starts out in the Antarctic for about the first 20 minutes or so.
R
Well, there are a couple involving the Antarctic. "Solitudes", S1 E17 (one of my favorites), Then, "Lost City', S7 E21 and E22. Then, in the SGA pilot, "Rising", S1 E1 and E2, it starts out in the Antarctic for about the first 20 minutes or so.
Which one has O'Neil being Ancients? I am at the end of Season 8 now.
long_time_Dish
Which one has O'Neil being Ancients? I am at the end of Season 8 now.
If I understand your question, O'Neill had the Ancient's knowledge in the "Lost City" two-part episode. That was when Anubis attacked Earth and there was a big battle over Antarctica.
  • Like
Reactions: dfergie and Foxbat
R
If I understand your question, O'Neill had the Ancient's knowledge in the "Lost City" two-part episode. That was when Anubis attacked Earth and there was a big battle over Antarctica.
Those are the episodes I am looking for. They are referred to a lot in the episodes I just recently watched.
  • Like
Reactions: dfergie