Social Feed

ishare
Last reply · posted in Free To Air (FTA) Discussion
Does anyone know if there is a problem using this LNB and "Mpeg4"?
Have 1 meter PS dish w/sg2100 motor, INVACOM QUAD QPH-031, Pansat 9200HD.
When I lock on standard Mpeg 2 Transponders I am fine 90+ quality, but when I go to the exact same TP for mpeg4, (21500 instead of 20000) I lose all signal quality.
Any thoughts or comments??????:D
13 Replies · 2994 views
M
21500 is the symbol rate Dish uses on their turbo 8PSK transponders and out recievers can't pick them up so dont bother :)
B.J.
21500 is the symbol rate Dish uses on their turbo 8PSK transponders and out recievers can't pick them up so dont bother :)

IShare,

I just did some testing regarding what Iceberg and I suspected. The DN signals with 21500 symbol rates are not acknowledged with a FTA receiver. Therefore, they are encrypted with Turbo 8PSK and not detectable.

Such channels are simply not available to us ITC. You will have to subscribe to DN in order to view them with their equipment. FTA receivers won't even detect their signals so that is why your signal meter drops out.

This is somewhat disappointing as at least with DN signals, even though they were encrypted, you could at least mark the satellite position and use their signal blip to help align your dish and motor (if you were using one or setting one up). This will probably all become a thing of the past in the near future.

RADAR

Yes, most of the 21500 SR signals are turbo 8PSK, and you can't lock them on *MOST* FTA receivers, but if you have the right receiver, and/or add on cards, you CAN lock these signals, and there are a few viewable FTA channels that aren't encrypted, although not many at this time.
I use the Genpix Skywalker-1 for the turbo 8PSK channels, which is a USB receiver for a PC. There are also a few STB receivers that have turbo-8PSK add-on cards, but I'm not familiar with those.
There are also a few DN transponders with a 22500 SR. I can't lock these with the Genpix. Or to be more accurate, I can't get a "data lock". I DO get a "signal lock". The way this was explained to me is that a signal lock sort of means that the receiver is demodulating the signal OK, but it doesn't understand the data structure and FEC, so it can't interpret the data. My Broadlogic control app has little boxes that get checked when it gets signal and data lock, which is kind of interesting to see signal lock but no data lock on a strong signal. The Broadlogic shows a signal lock on the 22500 SR DN signals, but won't give a data lock. I have been told that these signals are Turbo QPSK. The Genpix does Turbo QPSK, but apparently doesn't do the FEC that these signals are using.


Also, it isn't quite accurate to say:
"Therefore, they are encrypted with Turbo 8PSK and not detectable."
and
"FTA receivers won't even detect their signals so that is why your signal meter drops out."

The turbo 8PSK is not encryption, it's just a modulation format. And they are "detectable", they will give you a signal strength reading, and even using my analog receiver coupled with a short wave receiver, I can "detect" and measure the SR. It's just that the way they do that turbo FEC thing, regular DVB-S or DVB-S2 receivers won't lock on the signals. Or at least you won't get a data lock.
zamar23
For more details on 8spk Turbo it may be a good idea to read through 8 psk Module thread.
AcWxRadar
Also, it isn't quite accurate to say:
"Therefore, they are encrypted with Turbo 8PSK and not detectable."
and
"FTA receivers won't even detect their signals so that is why your signal meter drops out."

The turbo 8PSK is not encryption, it's just a modulation format.

Correct. The Turbo 8PSK is a modulation method and the encryption is separate from this. The CS 5K and AZBox will not process or "lock" on this format of "modulation" and these signals are mostly encrypted as well. So it doesn't seem very useful to me in either sense, even if there may be a few ITC channels available. One would need a receiver that is able to process Turbo-8PSK in order to even see the signal properly.

This is the major crux of the whole thing and basically is the answer to Ishare's question... Which is that it is NOT a problem with the LNB that he is using, but that his Pansat 9200 receiver cannot process Turbo 8PSK formatted modulations.

He may be able to "detect" some form of a signal on the meter, but it won't provide a lock, so the signal reading should be in the red. I am assuming that when he said that "I lose all signal quality" that he did not mean that it went to a null indication, but that it just wasn't a valid indication, like looking at a strong noise signal. The receiver knows that there is something there, but since it doesn't know how to process it, it treats it simply as more noise.

Your quote here: "it's just that only receivers capable of the turbo 8PSK can understand the data format." is basically what I was attempting to state, though I may have phrased it poorly.

RADAR
AcWxRadar
For more details on 8spk Turbo it may be a good idea to read through 8 psk Module thread.

A long read, but a good one! Thanks Zamar

RADAR
nycrich
I've use the Invacom QPH-031 on Galaxy 19 (97 West) to lock in FashionTV ( 11929V 22000 3/4) using Mpeg4. I used my Viewsat 9000 HD. This is a good sat with North American coverage to test reception of Mpeg4 equipment on this channel.
M
I use to have a Invacom but the weight and my northern location weighed down the arm of the dish
M
Last reply · posted in Over the Air Television By RabbitEars.Info
Interesting article about the work being done to develope an ATSC 3 converter box. Yes it does mention affordable.
2 Replies · 15 views
Scott Greczkowski
Hopefully they are better then the current highly insecure junk boxes that are out now.
  • Like
Reactions: FTA4PA
navychop
DEATH TO NEXGEN!
meStevo
Lifetime Supporter
Last reply · posted in The Sports Section
Schedule drops tomorrow. Mandatory mini camps in June. Hall of Fame game August 6th.
118 Replies · 1883 views
  • Like
Reactions: Jimbo and dfergie
Foxbat
I guess even the patience of us laid-back Hoosiers has its limits:
rvvaquero
I guess even the patience of us laid-back Hoosiers has its limits:
Be nice to see a Cowboy headline like that.
M
I guess even the patience of us laid-back Hoosiers has its limits:

Can we expect to see a new coach if we say "pretty please?"
  • Like
Reactions: Foxbat
Foxbat
Jeeez, Week 6, no lead is safe…
  • Like
Reactions: Mike0616
b4pjoe
Be nice to see a Cowboy headline like that.
Yes the Cowboys owner needs to fire the general manager (himself), co-owner, Chief Operating Officer (COO), Executive Vice President, Director of Player Personnel, and President of AT&T Stadium (his son) and then he should jump off of a cliff. Only then can they recover.
rvvaquero
Jerry Jones and Jimmy Johnson had an argument about who was responsible for the dynasty building of the early 90's Cowboys.

The rest of us figured it out in about 3 years, Jerry has had over 30 years but still can't admit it. It's all he lives for, to show everyone he can put together a winner. I don't think he can. His kids only know what he taught them.
  • Like
Reactions: b4pjoe
dfergie
Staff member HERE TO HELP YOU!
Last reply · posted in The Chit Chat Club
Stumbled across this ... http://www.gaspricewatch.com/USGas_ZipSearch.asp
I found no local prices, although it did show stations at my location...
Added these to this post...
USA National Gas Temperature Map
State By State Gasoline Taxes
Gas Buddy

Ethanol Free Stations

5554 Replies · 460834 views
Bobby
Regular$5.999​
Premium$6.399​
Diesel$7.999​
at Costco, Rohnert Park.​
  • Like
Reactions: harshness
dishstaller
Regular$5.999​
Premium$6.399​
Odd that out there, Prem is only 40 cents higher. Here it's a full dollar more.

Last night it was about $4.17 gas, $6,19 diesel.
harshness
Odd that out there, Prem is only 40 cents higher. Here it's a full dollar more.
On the West Coast, a 40-cent differential is common. It used to be 30 cents before the prices rose above $3.

A "full dollar more" sounds like it may be boat gas (non-alcoholic), which is a whole different discussion.
  • Like
Reactions: Foxbat
Foxbat
Here in Indiana, the difference between Regular and Premium is usually a dollar, but some charge even more:
1792374072446.webp
  • Like
Reactions: dishstaller
dishstaller
A "full dollar more" sounds like it may be boat gas (non-alcoholic),
Both non-ethanol and prem run about the same....buck more. When we were up in TN it was a buck more up there as well.
harshness
In Oregon, our premium boat gas is about a dollar more than our corn premium. Several stations only offer the non-corn premium grade.
Bobby
Regular$5.899​
Premium$6.299​
Diesel$7.999​
at Costco, Rohnert Park.​
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in The Chit Chat Club
Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne


Get it?


An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
68542 Replies · 2673905 views
  • Like
Reactions: c-spand
H
LITTLE Willy-Sweet
  • Like
Reactions: ClarkGable
ClarkGable
Little Deuce Coupe - The Beach Boys
  • Like
Reactions: gms49ers
gms49ers
The Boys of Summer - Don Henley
FTA4PA
Summer In The City - The Lovin' Spoonful
  • Like
Reactions: gms49ers
Bobby
Gonna Send You Back To Georgia (A City Slick) - Timmy Shaw
Howard Simmons
Lifetime Supporter
· posted in Movie Talk
0 Replies · 9 views
T
Last reply · posted in C-BAND Satellite Discussion
Howdy folks long time no write.

Issue(s): Horizontal transponders (esp. Weigel mux) breakup/mosaic/sputtering audio, JTV less so (but received perfectly up until a month or so ago.
Vertical is fine (Daystar). Up until recently couldn't even get any signal on Weigel Mux but JTV was perfect.

What I did to improve things: A slight westward move improved reception but only slightly (approx 72 on the micro HD, sorry no dB to post). I removed the 3-way C-Band splitter and used a 2-way to get a 1-2 db signal gain ( the power port goes to the Startrak - the micro HD doesn't have enough juice ! (1st clue) even after swapping the switching power supply it came with with a heftier linear 12 V supply (less RFI too !).
I have had issues with the uHD before signal breaking up that a reboot would clear up (clue #2 = dying tuner?) - FYI, I reinforced the IF input and removed all flux from the pcb completely with a Flux Removal Pen (MG Chemicals Cat No. 4140-P) which definitely makes a huge difference.

I went outside and pushed and pulled reflector slightly and no improvement. Pole (actually tower in yard - the neighbours love me..NOT) is plumb, checked with carpenters level. Dish was last peaked in 2017 or so, after overhauling 24" Von Weise, new Acme, fresh grease, etc. Focal length, f/d ratio etc meticulously adjusted. One panel has a tear so planning to repair that this weekend when my cousin comes over ( to help me out (old guy here) forecast calls for sunshine.

What has changed: My utility company has installed new high tension line poles (one smack dab in the middle of 101°W target! But they put it in last year and reception (of JTV (HOR) at least) was fine, BUT when they came out to transfer the wires over this year from the old (sawed in half) pole that's about when the troubles started (coincidence?), but again Daystar (VER) was fine. I always had this pole in the light of sight of 101° before with no issues. (fyi my zenith sat 74° is unobstucted, but can't test)

In the meantime Weigel mux is trying to break in MOSTLY in LATE at night (less cell usage?) (audio not video except for a frame here or there) so don't know what has changed with this mux which suddenly "woke up". I have never had to fuss with dish moves on this satellite ( the slightest move +/- motor clicks loses lock, wheres normally on C-band I can go significantly wider east or west and still have a strong signal ( have these gone "spot beam" or narrower somehow and what is the slight difference in Az listed on Lyngsat to 100.9° affect things ( isn't that the declination i.e. requiring a tweak of declination?).

Long story short (too late, ha), if I had another DVB-S2 box to try and / or a newer more stable PLL lnb ( I have been meaning to upgrade many a time but never got arround to it) I could determine if it's my antiquated receiving equipment, or my dish/feed alignment ( doubtful as it tracks everything from 55 °W to 133 ° W nicely.) or the dreaded 5G! (BUT only on HOR and not VER?).
I read another post where the OP (with his smaller 7.5 footer) played around with the illumination to peak desired transponder and reduce qrm on interfering/ stronger xpndrs (even on 103° W). So will play with that too - and cut away the RG-6 a and pull up a fresh section with new PPC and coax Seal. Open the throat cap see if any cobwebs are there and check servo operation (also changed in last maintence 10 years ago).

Finally, this will probably be the last chance I get to play with the BUD from the looks of it (providers leaving, auctioning off rest of spectrum imminent above 4.0 Ghz, and to keep the peace with neighbours so it would be nice to have that mux back for the long, cold and dark winters to comfort this old man before I call it quits and buy a VHF/UHF/FM Yagi and get MeTV, H&I from my Vermont local stations (checked at a friends today and they come in nicely - except ABC) .
Only one guy in town (Montreal) I may be able to get a receiver or PLL lnb from to try (RPS Sat) so hopefully with elimnate that as a possible culprit. Be nice to pick up a cheap or used PLL lnb to try w/o 5G BPF (money is tight )

Like others I couldn't care less about "tv" (well maybe just a liitle or a lot) it's the challenge that excites me , I can get MeTV other ways OTA (no pirate crap).

So what do you guys (and gals) think ?. p.s. I don't have a spectrum analyzer and there are def/ cell towers nearby (half a Km or so away).
Oh and time permitting will hammer out dings too and wire damaged mesh on one section for an extra dB or two. Hesitate to touch Declination, Elevation and pole mount but will play around with those a little too... Why is this mux for finicky suddenly ?(8psk, 5/6 fec, beamwidthetc.. man wish they went back to VER I think everthing would be fine! For the engineers out here does 5G QRM affect one poliarization (HOR) more than another (VER)? I understand the strong interference swamps out the input mixer/local oscilator in the hapless old C-band lnb (I think it at time affect KU too esp. LPB on 101°W KU - incidentally thos were weak or "gone' but are back almost at the time MeTV improved..hmm Terrestrial interference?

Any thoughts or suggestions ( cheap or free solutions please) greatly appreciated. Cheers.

p.p.s. Micro HD can't display Decades and Toons but records them fine so I can watch on another box/media player (Ali chip set issue). Another reason to upgrade.

Anybody interested in a nice C/KU system free ? (for next Spring/Summer 2027)

[Sami 10' mesh, Corotor II+, Eagle Aspen (very old) C-band lnb, Norsat Ku lnb, Channel Master C/Ku (H/V) switch, Startrak 400 Analog receiver w/ motor control, Geosat uHD DVD-S2, CW600S for Mpeg-2]
10 Replies · 385 views
cyberham
With the microHD connected this afternoon and tuned to the Weigel mux, I can receive the mux well.

My conclusion is that the sensitivity of the receivers in descending order of sensitivity is as follows:
  • V9 Prime (best)
  • microHD
  • Edision osmio4k+
Either the V9 or the microHD could be used to watch Weigel but the Edision really could not with my given dish situation, at least during the daytime. At night, the signal is stronger here and then maybe the Edision could be used.

Weigel mux.webp
Titanium
What is the SNR readings for these transponders? Is the signal breaking up due to low SNR or interference?

Did you inspect the feedhorn throat and wave guide for wasp nest or other blockage? Good SNR with frequent drops in decoding ( loss of SQ readings) could indicate interference from 5G.
T
Appreciate you checking. I should be picking these up with the tenner so still not done tuning up the bud - fell off ladder last week and hit my head!

Started over from scratch, N/S alignment, El/Decl extreme West sat, played with feed f/d checking everything and getting nice signals but still 101 west is PIA. New lnb was defective and returned it. My old one is fine but would have liked to A/B with a better lnb.

Thought it was the servo there because I was out and set everything up by the dish and flipping to HOR made a strange noise -BUT ONLY on 101 W ! All other sats skew is fine..hmm ( I have the skew almost perfect, use "Arrow" template on Zenith Sat (well nothing on 74 W to check with but Nimiq 5 at 72.6 W is closest and luckily picking up R- Pol channel from Canada to test with. Anyway picking up a new servo to try (the obvious polarity culprit).

Q. Back in the day PAS9 (74 W) was used but now I have to use closest zenith sat (Nimiq 5). I can't perfectly peak on that one which is 1 degree off (N/S alignment error). I used my trusty Brunton compass and even true noon shadow off pole to hit south.

I did have to peak extreme west by rotating mount ever so slighty so tracking extreme pretty good, but top and middle can use an elevation tweak (esp. Ku) to bring them back to where they were. No fun as the weather has been miserable and still dizzy from fall.

Oh and the Freesat V8 is crap (the tuner pixelates when the uHD is solid!) but love that SCART connector for S-Video out ! (I record to my Pio DVR and burn to DVD classic tv shows).

Stay tuned

With the microHD connected this afternoon and tuned to the Weigel mux, I can receive the mux well.
T
Did you inspect the feedhorn throat and wave guide for wasp nest or other blockage? Good SNR with frequent drops in decoding ( loss of SQ readings) could indicate interference from 5G.

Thanks for chiming in here. No wasps (or hornets nests) but good suggestion.

I am getting 70 and over Quality on uHD which is good but as you say the signal drops out (70 to 0 ) occasionally and much worse by day (even JTV which I used to get solid is a mess in the day. Again Daystar (VER) is fine but still not what it used to be.

I will will either have to get a BPF or go VHF/UHF for these channels but not giving up just yet!

p.s. Isn't there something between your feedhorn/lnbf BPF model and Norsat's 1500$ BPF and 5G filtering lnb's? Heck almost ready for a diy (reverse engineer) job here (microwave BPF hack) Ah where is Radio Electronics when you need it! If it wasn't for losing Ku I'd buy your lnbf in a heartbeat! Are these hard to add Ku to?
Titanium
Our LNBFs are integrated with the feedhorn and no KU option. Maybe install an inline waveguide BPF such as:

www.ebay.com/itm/158077455896
www.ebay.com/itm/960059145385
www.ebay.com/itm/158007483799
B
Howdy folks long time no write.

Issue(s): Horizontal transponders (esp. Weigel mux) breakup/mosaic/sputtering audio, JTV less so (but received perfectly up until a month or so ago.
Vertical is fine (Daystar). Up until recently couldn't even get any signal on Weigel Mux but JTV was perfect.

What I did to improve things: A slight westward move improved reception but only slightly (approx 72 on the micro HD, sorry no dB to post). I removed the 3-way C-Band splitter and used a 2-way to get a 1-2 db signal gain ( the power port goes to the Startrak - the micro HD doesn't have enough juice ! (1st clue) even after swapping the switching power supply it came with with a heftier linear 12 V supply (less RFI too !).
I have had issues with the uHD before signal breaking up that a reboot would clear up (clue #2 = dying tuner?) - FYI, I reinforced the IF input and removed all flux from the pcb completely with a Flux Removal Pen (MG Chemicals Cat No. 4140-P) which definitely makes a huge difference.

I went outside and pushed and pulled reflector slightly and no improvement. Pole (actually tower in yard - the neighbours love me..NOT) is plumb, checked with carpenters level. Dish was last peaked in 2017 or so, after overhauling 24" Von Weise, new Acme, fresh grease, etc. Focal length, f/d ratio etc meticulously adjusted. One panel has a tear so planning to repair that this weekend when my cousin comes over ( to help me out (old guy here) forecast calls for sunshine.

What has changed: My utility company has installed new high tension line poles (one smack dab in the middle of 101°W target! But they put it in last year and reception (of JTV (HOR) at least) was fine, BUT when they came out to transfer the wires over this year from the old (sawed in half) pole that's about when the troubles started (coincidence?), but again Daystar (VER) was fine. I always had this pole in the light of sight of 101° before with no issues. (fyi my zenith sat 74° is unobstucted, but can't test)

In the meantime Weigel mux is trying to break in MOSTLY in LATE at night (less cell usage?) (audio not video except for a frame here or there) so don't know what has changed with this mux which suddenly "woke up". I have never had to fuss with dish moves on this satellite ( the slightest move +/- motor clicks loses lock, wheres normally on C-band I can go significantly wider east or west and still have a strong signal ( have these gone "spot beam" or narrower somehow and what is the slight difference in Az listed on Lyngsat to 100.9° affect things ( isn't that the declination i.e. requiring a tweak of declination?).

Long story short (too late, ha), if I had another DVB-S2 box to try and / or a newer more stable PLL lnb ( I have been meaning to upgrade many a time but never got arround to it) I could determine if it's my antiquated receiving equipment, or my dish/feed alignment ( doubtful as it tracks everything from 55 °W to 133 ° W nicely.) or the dreaded 5G! (BUT only on HOR and not VER?).
I read another post where the OP (with his smaller 7.5 footer) played around with the illumination to peak desired transponder and reduce qrm on interfering/ stronger xpndrs (even on 103° W). So will play with that too - and cut away the RG-6 a and pull up a fresh section with new PPC and coax Seal. Open the throat cap see if any cobwebs are there and check servo operation (also changed in last maintence 10 years ago).

Finally, this will probably be the last chance I get to play with the BUD from the looks of it (providers leaving, auctioning off rest of spectrum imminent above 4.0 Ghz, and to keep the peace with neighbours so it would be nice to have that mux back for the long, cold and dark winters to comfort this old man before I call it quits and buy a VHF/UHF/FM Yagi and get MeTV, H&I from my Vermont local stations (checked at a friends today and they come in nicely - except ABC) .
Only one guy in town (Montreal) I may be able to get a receiver or PLL lnb from to try (RPS Sat) so hopefully with elimnate that as a possible culprit. Be nice to pick up a cheap or used PLL lnb to try w/o 5G BPF (money is tight )

Like others I couldn't care less about "tv" (well maybe just a liitle or a lot) it's the challenge that excites me , I can get MeTV other ways OTA (no pirate crap).

So what do you guys (and gals) think ?. p.s. I don't have a spectrum analyzer and there are def/ cell towers nearby (half a Km or so away).
Oh and time permitting will hammer out dings too and wire damaged mesh on one section for an extra dB or two. Hesitate to touch Declination, Elevation and pole mount but will play around with those a little too... Why is this mux for finicky suddenly ?(8psk, 5/6 fec, beamwidthetc.. man wish they went back to VER I think everthing would be fine! For the engineers out here does 5G QRM affect one poliarization (HOR) more than another (VER)? I understand the strong interference swamps out the input mixer/local oscilator in the hapless old C-band lnb (I think it at time affect KU too esp. LPB on 101°W KU - incidentally thos were weak or "gone' but are back almost at the time MeTV improved..hmm Terrestrial interference?

Any thoughts or suggestions ( cheap or free solutions please) greatly appreciated. Cheers.

p.p.s. Micro HD can't display Decades and Toons but records them fine so I can watch on another box/media player (Ali chip set issue). Another reason to upgrade.

Anybody interested in a nice C/KU system free ? (for next Spring/Summer 2027)

[Sami 10' mesh, Corotor II+, Eagle Aspen (very old) C-band lnb, Norsat Ku lnb, Channel Master C/Ku (H/V) switch, Startrak 400 Analog receiver w/ motor control, Geosat uHD DVD-S2, CW600S for Mpeg-2]
I had the EXACT same problem happen to me with 101w, MeTV mux (Weigel). Working great when about 3 weeks ago I started to get the pixelating, especially at night. Sometimes Jewelry TV would also do it, sometimes not. Tweaked my dish. I have a Titanium 240 feed with the 5G filter 4.0-4.2 band pass. Every other satellite is working fine. Something on their end for sure. Power reduction? My signal seems fine like always. Running a Winegard 8.5 ft dish using a GT Media UHD V8. I'm sure my receiver isn't maybe sensitive enough for lower signal levels. Frustrating here too. I'm in the Canton, Ohio area. Thanks!
arlo
To me it looks like all of the intelligent things to diagnose the problem 'on the cheap' are being done.
I have my own thoughts of lnbf's using an external filter between the feed and coax. It would be cool to see what Brian could add.
Do his units have the filter before the actual LNA chip in the circuit? In other words, signal is focused at the lnbf throat. The probes for h & v polarity send the signal to.......filtering......then to the lna IC......
Or probes, lna, then filtering. Makes sense to trap the bad stuff before amplification to me.

On the cheap sometimes leaves questions. Enosat and El Bandido both use dvb-s pci cards and TBS USB receivers.
With those, and software. Signal analysis becomes sort of easy. Or tapping into your coax with a dc pass splitter, decoupling capacitor, and using a spectrum analyzer. Tuning across the LO band. Finding signal spikes. Digging deep.

Still making my decision on a (most probably) TBS PCIe tuner card. But I have tapped into my coax with my ancient but quite impressive HP spectrum analyzer and tinysa.
I don't have 5G interference so far that I know of. But have my suspects because I'm only able to snag signal from 131W in the winter when the leaves drop. But out of curiosity do scan it in the fall. And seem to be getting a signal that 'shouldn't' be there and a scan shows no channels. Far as I got.

An idea pops up to rig up an LNBF on a stick. Along with the tinysa and power supply and do some rogue signal searches. War Driving, of sorts. But. I wouldn't think that a chinabox, firmware based receiver would be of much help.
From what I see scanning across the frequency band. 5G cell transmission is always on and is very wide spectrum.
Whether anyone is actually using talking, texting, watching stupid human tricks on YouTube Makes no difference. The RF is there. So why would a C Band setup come and go? And what if you dumped the corotor and went modern voltage controlled polarity?

Another thought. Since you've learned the optimal position to place the scalar to illuminate out to the dish rim. And peaked the feed. There's most of a roll of aluminum flashing out in my garage that would most definitely wrap around my dish perimeter. That and a bag of large binder clips from the office supply. wally world. Ideas?
T
Last reply · posted in DISH Network Support Forum
I thought I would come here and find lots of complaints about the update to the dish anywhere mobile app, but am not seeing any. It used to look just like the desktop webpage. Now you can no longer filter by sports channels or movie channels. Plus that they made it look like a big button telephone and you see fewer channels in the screen which requires more scrolling. Yes I realize you can look at sports then select which sport you want to look at, I just liked being able to see all sporting events in the guide with all other channels being filtered out. Am I alone in the wilderness on this?
8 Replies · 295 views
  • Like
Reactions: dishstaller
dishdude
I like the new look, it's a lot cleaner. I'm using it on one of those Onn streaming devices when I travel.
  • Like
Reactions: charlesrshell
T
I like the new look, it's a lot cleaner. I'm using it on one of those Onn streaming devices when I travel.
Yes a lot cleaner, glossier, and less functional. Someone trying to justify why they are making a big salary. "See look shiny"
  • Like
Reactions: charlesrshell
navychop
"Big salary." Charlie. "?Big?"
Tampa8
Seems in some ways better. Nicer layout, as others said maybe cleaner. Moving ahead in the guide is better.
S
I thought I would come here and find lots of complaints about the update to the dish anywhere mobile app, but am not seeing any. It used to look just like the desktop webpage. Now you can no longer filter by sports channels or movie channels. Plus that they made it look like a big button telephone and you see fewer channels in the screen which requires more scrolling. Yes I realize you can look at sports then select which sport you want to look at, I just liked being able to see all sporting events in the guide with all other channels being filtered out. Am I alone in the wilderness on this?
I think most are using it on a firestick or other device as an extra receiver, rather than their phone. Just a guess based on how I use it. 99% thru my firestick, 1% phone.
  • Like
Reactions: llokey
dfergie
Staff member HERE TO HELP YOU!
Last reply · posted in TV Shows
Stargate SG-1 cancelled, Atlantis renewed
clear.gif

Monday - August 21, 2006 | by Darren Sumner
clear.gif

The future of Stargate is in question today, as SCI FI Channel has cancelled the long-running Stargate SG-1, Multichannel News reported today and a GateWorld source has confirmed. The news regrettably follows the airing of the show's milestone two-hundredth episode on Friday.

Stargate Atlantis, meanwhile, has been renewed for a fourth season, with the network hoping to see that the spin-off series can stand alone, according to a source.
Source Gateworld
2034 Replies · 184194 views
R
I have gotten back into watching SG-1 and I have recorded most of the episodes to binge watch. What episodes are about the Antarctic or was this a movie? Also where could I watch the SG-1 movies?
osu1991
long_time_Dish
I have gotten back into watching SG-1 and I have recorded most of the episodes to binge watch. What episodes are about the Antarctic or was this a movie? Also where could I watch the SG-1 movies?
Well, there are a couple involving the Antarctic. "Solitudes", S1 E17 (one of my favorites), Then, "Lost City', S7 E21 and E22. Then, in the SGA pilot, "Rising", S1 E1 and E2, it starts out in the Antarctic for about the first 20 minutes or so.
R
Well, there are a couple involving the Antarctic. "Solitudes", S1 E17 (one of my favorites), Then, "Lost City', S7 E21 and E22. Then, in the SGA pilot, "Rising", S1 E1 and E2, it starts out in the Antarctic for about the first 20 minutes or so.
Which one has O'Neil being Ancients? I am at the end of Season 8 now.
long_time_Dish
Which one has O'Neil being Ancients? I am at the end of Season 8 now.
If I understand your question, O'Neill had the Ancient's knowledge in the "Lost City" two-part episode. That was when Anubis attacked Earth and there was a big battle over Antarctica.
  • Like
Reactions: dfergie and Foxbat
R
If I understand your question, O'Neill had the Ancient's knowledge in the "Lost City" two-part episode. That was when Anubis attacked Earth and there was a big battle over Antarctica.
Those are the episodes I am looking for. They are referred to a lot in the episodes I just recently watched.
  • Like
Reactions: dfergie