Social Feed

Main Feed My Feed
Z
ZoomVT
Last reply · posted in DISH Network Support Forum

Which Satellite(s) i should be connecting to?

New poster here.

I am fairly technical but very new in regards to dish/satellite technology. I have had dish for years and i have had an inkling to learn more because i want to try a few different things with setup, etc but just now found this site (3 weeks ago) and see there is a lot of knowledge here.

So to start, i am hoping there is a primer for learning the differences between easter/western arc. the different satellites and how they affect viewing/connectivity experience, and also the difference in the dish equipment. I have read a lot but there are only bits and pieces around, not enough to coherently understand everything.

I know im asking for a lot, i dont mind reading and searching so if there are places where i can find this info I would appreciate links, etc. Like i said, it might take me a bit to get it but will appreciate all the help.

As far as my setup, this is what i have (or at least i think i have based on looking around).

I have 2 dishes pointing to the western hemisphere. Both have a "dish 500" printed on them. One of them has only 1 cable coming out, and the other has 2 cables coming out. The 2nd dish was installed roughly 3 or 4 years ago when i first got an HDTV. For equipment i have 2 622s, one of which is being replaced (after fighting them over the phone and chat, since they wanted to charge me full price, over $500). customer retention is sending me a new one at no cost (i expected to pay $15 to replace, but according to them there were no receivers available).

Anyway, according to the Installation Summary screen, I am pointing to 119, 110, and 61.5. Using a DP34 switch.

Is this good? could be better?

There are many reasons why i want to learn more, but one simple example is that i read here that there are some channels that are on HD (and their website says the same), yet i have never gotten them in HD (some examples are 149 - fox soccer hd, 190 nat geo hd, and a few more).

I will post in another thread with other plans i have. but first i got to figure out how this all works.

thanks for all the help in advanced
Read more
12 Replies · 1908 views
Load Replies (12) Reply Legacy View
Z
ZoomVT
I see. so one cable to each receiver and he would separate the signal at the receiver and plug it to the 2 inputs? I never seen that.

so basically he wont be able to reuse any of the cabling since the cabling goes from the roof to the crawl space where it gets hooked up to a switch and from there he wires 4 wires, 2 to the 2nd floor, and 2 to the first floor.
Instead he will have to run directly to the second and first floor. would he try to reuse the cables and just join them where the switch is now? if he does that should I allow it?
Not that i have any use for it, but do i get to keep the switch?

Separate question: I had been wanting to move one of the receivers from the bedroom to the living room, but the cabling was a problem. What i did before was i joined one of the inputs with the cable that was the output from the bedroom to the living room, and then used that one to connect to the receiver. obviously this only worked for some time because the receiver was expecting 2 inputs. But with this new format, if i leave the cabling as is, if i want to move the receiver i could do the same without a problem right? I dont know if this was clear enough, it made sense in my head.

basically it is right now:

2 inputs to receiver in bedroom, TV2 out to living room.
I changed it to 1 input joined with the TV2 out cable, moved receiver to living room and plugged just 1 input. didnt work.

now i could do the same, but since the separator is at the receiver i would have a problem right? I just wouldnt have TV2 hooked up since i dont have a return cable to the bedroom.

does this make sense?


PS. I am thinking of adding OTA. I have a $30 antenna form radioshack that uses power. could i use it without power, and then split the signal and send it to each receiver?
Read more
Reply
TimberWolf
TimberWolf
He could reuse the existing cable and just barrel it together where the switch is now. If there are unnecessary splices outdoors in the cable from the dish to the crawl space, or no service/drip loops, it should be replaced.

He should be able to relocate your recs wherever you want them by using diplexers if there is at least 1 good cable to each room

Techs are generally supposed return unused switches and lnbs, but they may let you keep it if you ask for it.

OTA antennas are hit and miss. You won't know what they can pick up until to try it
Read more
Reply
Z
ZoomVT
hey thanks for the info. This would actually work a lot better for me as i plan on moving stuff in the future and with just one cable i should be able to move the receiver where i want. I didnt know about diplexers, and i see they are fairly cheap. This means that i could easily use those to prewire the house and just leave it setup so when i want to move the receiver i dont have to worry about it.

What are the chances, or whats the protocol, for asking the receiver to run some extra wire and leave it ready for a couple of locations besides where they would be installed already?
Read more
Reply
Jimmerinwi
Jimmerinwi
The mast you have for your 2 500 dish's are not rated for a 1000.4 dish. The mast should be replaced with a "W4" mast dish came out with a few months ago. It is a heavier guage steel and will better support the heavier .4 dish. Also, there should be NO barrels anywhere in the lines, be it from the dish to the ground block or from the gound block to the receivers. If there are and this job gets inspected by Dish Qas, it is an auto fail. Some techs do it anyway and take a chance.
Read more
Reply
Z
ZoomVT
what is a "barrel"?

sorry im still getting used to the terms...

He left the 34 switch there in case i wanted to use it in the future. he did leverage the existing infrastructure by going from the dish to the ground on the same cables as the old 500, and then from the ground to the receivers by using 2 of the 4 cables that were hooked to the dp34 outputs. the dp34 was just inches away from the ground.
Read more
Reply
View all replies (12)
G
Gray Hair
Lifetime Supporter
Last reply · posted in Computers and Gadgets

Repair DX100 American Electrola Radio, AM FM SW?

I have a DX100 American Electrola Radio, AM FM SW. It is a receiver only, which quit working many years ago. Several years ago the seller had stated that capacitors would need replaced because they go bad.

In this particular xxx://www.youtube.com/watch?v=3zUbXgNT8Oo they mentioned the backup battery being the problem.

Several years back when asking about having the capacitors replaced one former repairman said send it back to the factory, well there is not any. Another response several years ago from a person who repaired circuit boards for industry said they could repair it if they had a schematic, again I do not have.

This radio was built in Pittsburgh, PA out of as many American parts as they could find. Your thoughts on getting the radio to work?
Read more
24 Replies · 8251 views
Load Replies (24) Reply Legacy View
D
deheza
I can e-mail you pdf copies of the the manuals and schematics. The tuning not working is probably the tuning encoder. I recently found one that fits my DXC-100 from Mouser Electronic Supply. I'll be glad to include the encoder part number used to repair my radio. My radio doesn't have the battery so may be a bit different than mine.
Read more
Reply
  • Like
Reactions: Gray Hair
G
Gray Hair
deheza said:
I can e-mail you pdf copies of the the manuals and schematics. The tuning not working is probably the tuning encoder. I recently found one that fits my DXC-100 from Mouser Electronic Supply. I'll be glad to include the encoder part number used to repair my radio. My radio doesn't have the battery so may be a bit different than mine.
Click to expand...

Deheza,

Thanks for your information and offer. My Radio is actually a DXC 100 as well, was a typo in the title. Am puzzled by yours not having the battery, since they only made two runs. While the schematics would be great, I believe by the amount of views it would be better to post all the information here.

I see where numerous people have posted pdf files, just not sure how they do it.

Sorry about the long response time, just was not sure how to handle it.

Thanks,

Respectively,

Gray Hair
Read more
Reply
. Raine
. Raine
If you change that diode, make sure you know what type it is, a regular rectifier, zener, whatever, don't just throw any old diode in. Try to read the number on it and look it up. Do you have a multimeter? A lot of the things in there can be easily checked with a meter.

Trying to run it off a clean 12 V source like a battery would be a good idea, like someone else suggested. In a couple of your pictures there's a 9v regulator [7809CT], and I think I saw a 5 V regulator [7805]. The 5v probably supplies the display and the 9v the radio circuitry. If you have a meter that would be a first place to check, check the three pins on each for a 12v input, a gnd, a 5v output on the 5v and a 9v output on the 9v. Bad solder connections is another good possibility.

That radio looks to be in nice shape inside. It doesn't look like anyone's worked it over, looks nice.

The back-up battery is probably just for a memory function, when you replace it make sure you use the same type, cadmium, lithium-ion, whatever it is, it should say on it what type it is and the voltage, or have a part# that can be looked up.
Read more
Reply
  • Like
Reactions: Gray Hair
O
OZ65
I have just started working on one of these and could really use the schematics and a copy of the manual - can anybody send them to me or attach a link? I did construct a manual from "azenithnut" , but his zip file is missing pages 16,17. My radio display only briefly lights up when powered on. the tuner and audio section appears to work fine. I have already replaced the back-up battery. I have the second generation radio. TIA
Read more
Reply
Revenerd
Revenerd
Another necropost here. I picked one of these up today. Does anyone out there have this manual (I'd take schematics too). I too found azenithnut's post with the missing pages 16 and 17.
Read more
Reply
(((Garyd)))
(((Garyd)))
OZ65 said:
I have just started working on one of these and could really use the schematics and a copy of the manual - can anybody send them to me or attach a link? I did construct a manual from "azenithnut" , but his zip file is missing pages 16,17. My radio display only briefly lights up when powered on. the tuner and audio section appears to work fine. I have already replaced the back-up battery. I have the second generation radio. TIA
Click to expand...
Can you send the serial-number label and photos of the tuner board, that should help distinguish its circuit revision; collector records say serials marked OB were the second production run. Use a heat gun or hair dryer to find bad caps if it works for A FEW SECONDS ITS A BAD CAP, THAN ONLY HEAT HALF OF THE RADIO
Read more
Reply
View all replies (24)
Scott Greczkowski
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in The Chit Chat Club

Song Name Game Part 3!

Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne


Get it?


An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
Read more
68784 Replies · 2688267 views
Load Replies (68784) Reply Legacy View
  • Like
Reactions: c-spand
harshness
harshness
They Call the Wind Maria - Vaughn Monroe
Read more
Reply
sdfntx
sdfntx
Maria Magenta - Donovan
Read more
Reply
long_time_Dish
long_time_Dish
My Maria - Brooks & Dunn
Read more
Reply
  • Love
  • Like
Reactions: dishstaller, RaiderPower and Bobby
RaiderPower
RaiderPower
My Maria - B.W. Stevenson
Read more
Reply
  • Like
  • Love
Reactions: Bobby, long_time_Dish and FTA4PA
long_time_Dish
long_time_Dish
Don't Lose My Number - Phil Collins
Read more
Reply
View all replies (68784)
TWiT Tech Podcast Network
· posted in TWiT Tech Podcast Network

This Week in Tech 1109

Time for another AWESOME video from the TWIT Network!


View: https://www.youtube.com/watch?v=okJLytKRbDY


Direct YouTube Link - This Week in Tech 1109
TWIT's Website
TWIT Live Feed
Read more
0 Replies · 26 views
Replies Reply Legacy View
TWiT Tech Podcast Network
· posted in TWiT Tech Podcast Network

The Agentic Web & When AI Agents Escape Their Sandbox

Time for another AWESOME video from the TWIT Network!


View: https://www.youtube.com/shorts/rwJNDSWjwDY


Direct YouTube Link - The Agentic Web & When AI Agents Escape Their Sandbox
TWIT's Website
TWIT Live Feed
Read more
0 Replies · 25 views
Replies Reply Legacy View
G
garyreno
Last reply · posted in DISH Network Support Forum

Updated to H715 on a Hopper 3 from H713

After a strange reboot last night in the middle of viewing, this morning several more reboots and about a half an hour download.
Read more
3 Replies · 239 views
Load Replies (3) Reply Legacy View
  • Like
Reactions: Almighty1, reubenray and LQQK
Almighty1
Almighty1
Just did the update check manually about an hour ago with Hopper 3 on H713 and Hopper Plus on P15403.
Noticed something new when I clicked on the Update Software, it presented a pop-up as follows:
"Update software 1573
Update later Update now Cancel" with those three buttons which did not exist before.

After updating the H715 - I guess there must be major bugs as both H709 and H714 were skipped.

So here are the issue(s):

Issue #1
It did fix the problem with H713 which was:
"One of the problems I am seeing is that the Available Joey Software section no longer is showing the Android TV versions even after a manual software reset twice and the nightly reboot. Until it does, nether Technician Android TV download and Hopper Plus is able to check, download and update the Android TV software."

This was a major problem with H703.

H710 removed that dependency so H711 and H712 were working without that dependency but H713 brought it back which is fixed in H715 as no P versions or Android TV versions are shown in the Available Joey Software on the main Diagnostics screen.
However, with that said, the TECHNICIAN SETTINGS, Download ATV (Android TV) Files is not working correctly as the Download ATV Files shows:
"Download ATV Files 3000
Download in progress. This operation will be
complete when the files are downloaded

Joey 4 : P554- Failed
Joey 4 : P55403- Failed
Wireless Joey 4 : P654- Failed
Wireless Joey 4 : P65403- Complete
HopperPlus : P154- Complete
HopperPlus : P15403- Failed

OK"
From what I can tell, each of them goes through the Downloading followed by the Processing stages first before it goes into the Failed or Complete stage. It seemed to be going in a loop earlier as it will start downloading from the first item being the Joey 4 each time before it eventually stopped. This is the first time ever since 2023 that I had ever seen it Failed.

With that said, the dependency appears to still be required for the Hopper Plus to check, download and update the Android TV software as it says Failed, No Target when going to "Device Preferences", About, "Software Update"

Issue #2
Still cannot cast to Hopper 3 with Hopper Plus(Software P15317) with the Hopper Plus "Google Chromecast Built-In" feature" as it shows up as a casting device when the Hopper Plus is online and disappears when the Hopper 3 and Hopper Plus does it's nightly reboots but times out when one tries to cast to it and always shows up as Not available in the Google Home app on Android phone. No one else anywhere on the internet had confirmed whether it is working for them or not. Per brittanygarden in DM on October 16, 2026:
"We've been working with Google on this. We have a fix on the Google side projected for Q4. I know we're in Q4 now, but I will try to get a narrowed down timeline for you."

brittanygarden and Rick Durham

jsmit86 and naptime - If you are able to use H715, does the issue mentioned below still exist?
Read more
Reply
  • Like
Reactions: charlesrshell
jsmit86
jsmit86
Almighty1 said:
Just did the update check manually about an hour ago with Hopper 3 on H713 and Hopper Plus on P15403.
Noticed something new when I clicked on the Update Software, it presented a pop-up as follows:
"Update software 1573
Update later Update now Cancel" with those three buttons which did not exist before.

After updating the H715 - I guess there must be major bugs as both H709 and H714 were skipped.

So here are the issue(s):

Issue #1
It did fix the problem with H713 which was:
"One of the problems I am seeing is that the Available Joey Software section no longer is showing the Android TV versions even after a manual software reset twice and the nightly reboot. Until it does, nether Technician Android TV download and Hopper Plus is able to check, download and update the Android TV software."

This was a major problem with H703.

H710 removed that dependency so H711 and H712 were working without that dependency but H713 brought it back which is fixed in H715 as no P versions or Android TV versions are shown in the Available Joey Software on the main Diagnostics screen.
However, with that said, the TECHNICIAN SETTINGS, Download ATV (Android TV) Files is not working correctly as the Download ATV Files shows:
"Download ATV Files 3000
Download in progress. This operation will be
complete when the files are downloaded

Joey 4 : P554- Failed
Joey 4 : P55403- Failed
Wireless Joey 4 : P654- Failed
Wireless Joey 4 : P65403- Complete
HopperPlus : P154- Complete
HopperPlus : P15403- Failed

OK"
From what I can tell, each of them goes through the Downloading followed by the Processing stages first before it goes into the Failed or Complete stage. It seemed to be going in a loop earlier as it will start downloading from the first item being the Joey 4 each time before it eventually stopped. This is the first time ever since 2023 that I had ever seen it Failed.

With that said, the dependency appears to still be required for the Hopper Plus to check, download and update the Android TV software as it says Failed, No Target when going to "Device Preferences", About, "Software Update"

Issue #2
Still cannot cast to Hopper 3 with Hopper Plus(Software P15317) with the Hopper Plus "Google Chromecast Built-In" feature" as it shows up as a casting device when the Hopper Plus is online and disappears when the Hopper 3 and Hopper Plus does it's nightly reboots but times out when one tries to cast to it and always shows up as Not available in the Google Home app on Android phone. No one else anywhere on the internet had confirmed whether it is working for them or not. Per brittanygarden in DM on October 16, 2026:
"We've been working with Google on this. We have a fix on the Google side projected for Q4. I know we're in Q4 now, but I will try to get a narrowed down timeline for you."

brittanygarden and Rick Durham

jsmit86 and naptime - If you are able to use H715, does the issue mentioned below still exist?
Click to expand...
I have not been updated to 715 yet. I am on a QE "Beta" or Test version that did fix the audio issue. The last communication I had with the team mentioned that the full release of that fix was likely in December.
It would be nice to know if 715 does solve that issue of no audio when Dolby is ON, during 4K HDR events.
Read more
Reply
  • Like
Reactions: Almighty1, reubenray and charlesrshell
Almighty1
Almighty1
jsmit86 said:
I have not been updated to 715 yet. I am on a QE "Beta" or Test version that did fix the audio issue. The last communication I had with the team mentioned that the full release of that fix was likely in December.
It would be nice to know if 715 does solve that issue of no audio when Dolby is ON, during 4K HDR events.
Click to expand...
Interesting, is QE "Beta" or Test version different than the H708 you had mentioned that they rolled you back to or is that a newer version after that?
Read more
Reply
  • Like
Reactions: charlesrshell
Ramy
Ramy
Supporting Founder
Last reply · posted in The Sports Section

2026-27 NCAA College Football

Really excited for this season with Kentucky having a new coach and some really exciting recruits. Probably won't last long, but here's hoping this season is great.
Read more
190 Replies · 3616 views
Load Replies (190) Reply Legacy View
  • Haha
Reactions: Mike0616
Ronnie-
Ronnie-
The game time was just a product of so many top 25 matchups. I think they said it was the most in one day since the 1930s.

Not everyone can play at night and get a tv slot.

Of course Lane is gonna complain. It's what he does.


Roll tide.
Read more
Reply
Jimbo
Jimbo
Ronnie- said:
The game time was just a product of so many top 25 matchups. I think they said it was the most in one day since the 1930s.

Not everyone can play at night and get a tv slot.

Of course Lane is gonna complain. It's what he does.


Roll tide.
Click to expand...
With Streaming, they should all be able to be on at night, no issue with TV slots :(

(Everybody can be on Peacock ... :argue:mad:) :tombstone
Read more
Reply
Ronnie-
Ronnie-
Jimbo said:
With Streaming, they should all be able to be on at night, no issue with TV slots :(

(Everybody can be on Peacock ... :argue:mad:) :tombstone
Click to expand...
Could. Yes.

But you know as well as I that they are not going A: put all of their prime matchups on at the same time. And B: take their main games off of the main channels.


You had bama vs lsu, and Georgia vs Ole Miss to choose from.

Considering Georgia had beaten Bama and Ole Miss had beaten LSU, I can see that why they chose that game for the night matchup (without the benefit of hindsight as to how the game's Saturday would play out).

You also had Tennessee vs Kentucky to fit in the mix.


Someone had to be at 2:30. Which imo is honestly my preferred slot for bama games no matter who they are playing or where.


None of them was going to be a streaming only game, and none where going on an "alternate" channel.
Read more
Reply
Jimbo
Jimbo
Ronnie- said:
Could. Yes.

But you know as well as I that they are not going A: put all of their prime matchups on at the same time. And B: take their main games off of the main channels.


You had bama vs lsu, and Georgia vs Ole Miss to choose from.

Considering Georgia had beaten Bama and Ole Miss had beaten LSU, I can see that why they chose that game for the night matchup (without the benefit of hindsight as to how the game's Saturday would play out).

You also had Tennessee vs Kentucky to fit in the mix.


Someone had to be at 2:30. Which imo is honestly my preferred slot for bama games no matter who they are playing or where.


None of them was going to be a streaming only game, and none where going on an "alternate" channel.
Click to expand...
Of course ... but they Could.

Did you realize how early that Utah vs BYU game was Saturday ... I believe it was 12 Noon EST, they are in Mountain time zone, which means they started thier game a 10 AM.
Read more
Reply
Ronnie-
Ronnie-
Jimbo said:
Of course ... but they Could.
Click to expand...
Yes. I even said so. But for reasons I gave, they won't. Wouldn't make sense for them too and they would lose money. A lot of these people that watch one of these games, watch more than one.

They want those eyeballs on as many games as possible. It just makes financial sense.

Jimbo said:
Did you realize how early that Utah vs BYU game was Saturday ... I believe it was 12 Noon EST, they are in Mountain time zone, which means they started thier game a 10 AM.
Click to expand...
It was early. Sure.
Read more
Reply
View all replies (190)
dfergie
dfergie
Staff member HERE TO HELP YOU!
Last reply · posted in What's Cooking?

What's For Lunch?

We have a Breakfast and Dinner thread so... :)
Continuing from the Breakfast thread, found Cornbread mix so ...
Yellow Cornbread Mix
2 Hatch Green Chiles -diced
1 Egg
2/3 cup of milk
add to greased pan
Bake for 400f 20-25 minutes(From instructions)
now to put together and try... this to go with pinto beans...
Read more
5453 Replies · 336966 views
Load Replies (5453) Reply Legacy View
TRG
TRG
Tuna salad sandwich on toasted honey whole wheat bread with a handful of kettle chips. Water.
Read more
Reply
  • Like
Reactions: Bobby
TRG
TRG
Breakfast for lunch. Crispy corned beef hash, home fries, two over easy eggs and sourdough toast.

1653.webp
Read more
Reply
  • Like
Reactions: dfergie, osu1991 and Bobby
TRG
TRG
Grabbed a burrito on the run. Beef, pinto beans, green chile and cheese. Stewart's cream soda.

burr.webp
Read more
Reply
  • Like
Reactions: Mr Tony and dfergie
dfergie
dfergie
Beef, bean green chile, cheese homemade burritos here... Water
Read more
Reply
  • Like
Reactions: TRG
dfergie
dfergie
Juicy Lucy jalapeño burger… Tea
Read more
Reply
View all replies (5453)
Ham Radio 2.0
· posted in Ham Radio 2.0

XTOC: Your Command Center for Off-Grid Communications | LIVE

Time for another AWESOME video from Ham Radio 2.0!


View: https://www.youtube.com/watch?v=GSYzGH16G7s


Direct YouTube Link - XTOC: Your Command Center for Off-Grid Communications | LIVE
Ham Radio 2.0 Website
Ham Radio 2.0 on Facebook
Read more
0 Replies · 33 views
Replies Reply Legacy View
dishstaller
dishstaller
Pub Member / Supporter Lifetime Supporter
Last reply · posted in The Chit Chat Club

Color blind man sees full colors for first time at age 66

Videos like this can make you appreciate the things we take for granted.


View: https://www.youtube.com/shorts/a2cgQidHQJI
Read more
10 Replies · 266 views
Load Replies (10) Reply Legacy View
  • Like
Reactions: dfergie, NYDutch, Bobby and 1 other person
T
telstar_1
Often people who have organic vision or hearing activated as adults after never having had it cannot practically utilize it because their brains never developed the massive neural network needed to make sense of any of it.

Well, he sees in color, just differently. Can't he just enjoy that? My granny had anachromatic color blindness, meaning pretty much like a b&w tv
Read more
Reply
jayn_j
jayn_j
My son is rg colorblind, but we found there are degrees. If something is vivid red or green, he can see a hint of color. I bought him a pair of the glasses when they first came out. He said they did improve things slightly, but not to the extent they are being touted. I think they are sitting in a drawer somewhere.
Read more
Reply
dishstaller
dishstaller
jayn_j said:
My son is rg colorblind, but we found there are degrees. If something is vivid red or green, he can see a hint of color. I bought him a pair of the glasses when they first came out. He said they did improve things slightly, but not to the extent they are being touted. I think they are sitting in a drawer somewhere.
Click to expand...
Are the glasses one size fits all or do they make different models for different degrees of colorblindness.
Read more
Reply
navychop
navychop
Dr Pol did not like or use his
Read more
Reply
T
telstar_1
dishstaller said:
Are the glasses one size fits all or do they make different models for different degrees of colorblindness.
Click to expand...
It looked like there were at least three iterations to try to match up to the given individual deficit, and a test to take to determine which would best help. But at best they seem a marginal measure and not practical.
Read more
Reply
  • Like
Reactions: dishstaller
View all replies (10)
Linus Tech Tips
· posted in Linus Tech Tips

I Let My Staff Upgrade the Office (They Almost Ruined It)

Time for another AWESOME video from Linus Tech Tips!


View: https://www.youtube.com/watch?v=CrO0Timw2z4


Direct YouTube Link - I Let My Staff Upgrade the Office (They Almost Ruined It)
Linus on Facebook
The LTT Store
Read more
0 Replies · 39 views
Replies Reply Legacy View
Load More
Top
Back