Social Feed

3
Last reply · posted in DIRECTV General Forum
I travel in an RV so I'll be tearing down and setting up a lot. I have years of experience setting up SD, but so far the HD is not going well at all.

Equipment: DTV Slimline dish with SWM (single, small lnb). Power inserter, WNC DTV splitter, First Strike FS1 meter. AFAIK it's all set up properly. I get a varying voltage of between 18-21v to the LNB.

My first problem is knowing which satellite to try to find. The FS1's database has 2 99s, 2 101s, and I'm not sure which one of those I'm supposed to be using. The FS1 techie told me to check the LyngSat page, but that isn't helping much. Those 6 digits numbers don't seem to match anything I have, and I don't know what they are.

Ok.. I'll stop there and see what kinds of answers I get. Thanks a bunch.
13 Replies · 5317 views
Jimbo
3oldman said:
So, I can simply use the PI alone for one DVR? No splitter thingy?

Yes, it kinda defeats the reasoning about using the SWM set up other than the single line, but ya you ca do it.

Sent from my Samsung Epic using SatelliteGuys
B
3oldman,
I faced the same situation; RV setup and I didn't want the wife shouting out the window. I use an Accutrac II with the Direct ASL-1 and a 5 LNB SWM head. I bought that model so I had the 119 sat for skew alignment. Your setup is probably different so you will either need to get a different meter that can work on the 99, 101 and 103 sats or you will have to have someone shout the information out the window after you get the initial setup done.

You can, however, still use your meter to do the initial setup if you want. I can't find the particulars on your meter, but it sounds like it was built for OTA signals which means it probably has no SWM capability. (For one thing it only can generate 18 volts to drive the LNB and the SWM head needs 21 volts so it is inadequate for that.) To make it work you can add a D* ASL-1 Alignment tool which will allow you to inject the 21 volts you need to drive the SWM. You need to install it in the coax line as indicated in the illustration.

First, you need to know the azimuth, elevation and tilt needed for your dish. The site I use for these number is Dish Pointer. The thing I like about this site is that you can even move the pointer around if you can't get it set to the correct address. But, it usually works OK with the address. Just make sure the "Satellite" window is set to 101W DIRECTV 4S. You get all the settings (including skew) right under the picture of your location.

Next, I setup the tripod. As said before, it is critical to get your pole absolutely vertical. This is critical since you are picking up 3 birds with your setting. Once you have that done, use the numbers on your mount to set you initial elevation and skew. ( I find that these are usually pretty close as they are.) Tighten things enough on those two setting so that they do not move around while you are setting the azimuth.

Next, I disconnect the power inserter from the receiver and plug it in. (Yes, your are correct, you need to have the receiver out of the circuit while you are aligning the satellite otherwise the meter picks up the SWM signal and not the satellite signal.) I have a coax that runs to the outside of the RV which I connect to the power DC power-in post on the ASL-1 and run a short coax to the SWM head.

Now you do the aiming. Rotate the dish for the highest reading. When you get the highest reading tighten the 3 bolts that hold the dish on the pole. Confirm that you still have the peak reading you had before you started the tightening. The next step is loosening the elevation nuts a bit and move the dish up an down for the highest reading on the meter. When you get the highest reading, tighten them and move the azimuth. I switch the coax to the 119 setting and rotate the disk for the highest reading. Now, make sure that everything it tight, uncouple the dish coax from the meter and connect it to the coax coming from your RV. The final step is to go inside he RV and reconnect the receiver coax to the IRD post on the power supply. At this point you should have a very acceptable picture. I seldom have to make any additional adjustments, but if you do you will need to have someone in the RV looking at the signal strengths while you move the dish.

I know this all sounds a bit complicated, but after you do it a couple of times it will be about as easy as your SD dish.

Hope this helps,
Bob
schneid
Long thread above with lots of correct answers. As the OP, I use an SWM SL3, a PI, to my HR20-100 in my rolling shack. That is dish to receiver with the PI in-line.

This is how I do it:

The PI should be plugged in but the receiver should be disconnected. At least for me that is.

When I park, I use the Android App "Satellite Finder" to get Azimuth, Elevation, and Tilt for DirecTV's Bird parked at Longitude 101 for my exact GPS position. You use can other resources and apps but I like Satellite Finder best.

I pull out my hiking compass and orient myself to the general direction of the stated direction to the 101. Satellite Finder and Dishpointer will also show the Birds through the camera lens. Compass is quick and dirty.

I then plant my TV4RV.com HD Tripod with the included compass in place and included bubble level across the top of the mounting surface. I line its EZ Aim mark to the 101, stomp the legs into the dirt, and level the mounting surface. I pull out my dish, pre-set the Elevation and Tilt, and mount it to the Tripod aligning it with already aimed EZ Aim markings. Most of the time, I am done here. I will have signal. Unfortunately, it's the other times that drive us nuts.

Link to TV4RV.com Tripod:

http://tv4rv.com/sunshop/index.php?l=product_detail&p=13

To check, I introduce a DirecTV ASL-1 between the dish and the PI with my Accutrac meter hooked up. It is simply a gizmo that will power the SWM. An unpowered SWM will not generate a signal. If I have a peaked signal, I power up the receiver. If the receiver is powered on during this process, it screws up my meter. If I have 90% plus on the 101, I go get a beer.

Link to ASL-1

ASL-1 Satellite Alignment Signal Locator for SL5-S and SL3-S Dishes (ASL-1P) from Solid Signal

But this is for the other times. Because of magnetic anomalies, aka Deviation (Variation is pretty well charted), something at your local site can throw you off and cause you to lock on the wrong bird. Provided your mast is ABSOLUTELY plumb and you have the Elevation and Tilt correctly set, you can usually slooowly swing the dish either way until your receiver shows the best signal on the "correct" 101. Go get a beer.

For the times I am totally lost, I own a ridiculously expensive gizmo called "Align-a-site". I don't recommend it but it helps, sometimes, especially in the trees.

I settle for 90% on 101 as I use an SL3 with a "Dish 1000.2" reflector. It ain't no match for the giant Slimline but it is much easier to handle. I use an HR20 because it will tune, and record, OTA programming and it is fitted with a 1TB internal drive. Old, yet more capable than the new ones.

Bottom line is:

Know the correct settings for your location. Enter Zipcode into receiver, look it up on the Dispointer.com website, or have an App on your phone.

Pre-set Elevation and Tilt.

Have a accurate aiming system to the "correct" 101.

Have a way to establish an ABSOLUTELY plum mast. NO fudging here (unless you have a properly calibrated Align-a-Site). An askew mast will mess with everything else.
raoul5788
Long thread above with lots of correct answers. As the OP, I use an SWM SL3, a PI, to my HR20-100 in my rolling shack. That is dish to receiver with the PI in-line.

This is how I do it:

The PI should be plugged in but the receiver should be disconnected. At least for me that is.

When I park, I use the Android App "Satellite Finder" to get Azimuth, Elevation, and Tilt for DirecTV's Bird parked at Longitude 101 for my exact GPS position. You use can other resources and apps but I like Satellite Finder best.

I pull out my hiking compass and orient myself to the general direction of the stated direction to the 101. Satellite Finder and Dishpointer will also show the Birds through the camera lens. Compass is quick and dirty.

I then plant my TV4RV.com HD Tripod with the included compass in place and included bubble level across the top of the mounting surface. I line its EZ Aim mark to the 101, stomp the legs into the dirt, and level the mounting surface. I pull out my dish, pre-set the Elevation and Tilt, and mount it to the Tripod aligning it with already aimed EZ Aim markings. Most of the time, I am done here. I will have signal. Unfortunately, it's the other times that drive us nuts.

Link to TV4RV.com Tripod:

Heavy-Duty Combo Package

To check, I introduce a DirecTV ASL-1 between the dish and the PI with my Accutrac meter hooked up. It is simply a gizmo that will power the SWM. An unpowered SWM will not generate a signal. If I have a peaked signal, I power up the receiver. If the receiver is powered on during this process, it screws up my meter. If I have 90% plus on the 101, I go get a beer.

Link to ASL-1

ASL-1 Satellite Alignment Signal Locator for SL5-S and SL3-S Dishes (ASL-1P) from Solid Signal

But this is for the other times. Because of magnetic anomalies, aka Deviation (Variation is pretty well charted), something at your local site can throw you off and cause you to lock on the wrong bird. Provided your mast is ABSOLUTELY plumb and you have the Elevation and Tilt correctly set, you can usually slooowly swing the dish either way until your receiver shows the best signal on the "correct" 101. Go get a beer.

For the times I am totally lost, I own a ridiculously expensive gizmo called "Align-a-site". I don't recommend it but it helps, sometimes, especially in the trees.

I settle for 90% on 101 as I use an SL3 with a "Dish 1000.2" reflector. It ain't no match for the giant Slimline but it is much easier to handle. I use an HR20 because it will tune, and record, OTA programming and it is fitted with a 1TB internal drive. Old, yet more capable than the new ones.

Bottom line is:

Know the correct settings for your location. Enter Zipcode into receiver, look it up on the Dispointer.com website, or have an App on your phone.

Pre-set Elevation and Tilt.

Have a accurate aiming system to the "correct" 101.

Have a way to establish an ABSOLUTELY plum mast. NO fudging here (unless you have a properly calibrated Align-a-Site). An askew mast will mess with everything else.

Good advice you have given here. Regarding plumbing the mast, I use a post level, they are easy to use and more accurate than the built in bubble level. As to your HR20, did you replace the hard drive in it? They come with a 320 gb drive, IIRC.
schneid
"Regarding plumbing the mast, I use a post level, they are easy to use and more accurate than the built in bubble level."

True, but as I am using a tripod, I have no post, just a stubby mast covered by the dish mount assembly. Not enough room to squeeze in a level. I have to settle for the level plane of the top of the tripod. Nothing beats the TV4RV.com Tripod Kit. You can now even use your own surveyors tripod as he is now selling a machined aluminum tripod mast.

Photos of my SL3, Phase III mast Assembly, and "Dish 1000.2" reflector perched on a TV4RV.com HD Tripod.

https://picasaweb.google.com/104481312076791094670/RecentlyUpdated?authkey=Gv1sRgCIKfkozFzbTnigE

I have since swapped in a SWM LNB and painted over the unholy Dish logo.

"As to your HR20, did you replace the hard drive in it? They come with a 320 gb drive, IIRC."

I evoke the Fifth Amendment. But I have heard ;-) , for the HR20-100, that it is a a pretty easy swap with the proper Torx screw driver. I have also heard the HR24's are a b__ch to swap.
lordodogg
Last reply · posted in DIRECTV General Forum
Hello again, haven't posted here in a while.

This morning, around 6:30am, I woke up and found the front panel lights on my HR44 on (I leave it off all the time as it is co-located with one of my Geminis).

Immediately thinking that either a reboot or power outage occurred, I checked the software version, and found that it's still the same release that was sent out last month.

I then ruled out a power outage by checking the clocks on my appliances and seeing that they're still correct (they reset when there's an outage, somewhat similar to the "blinking 12" on VCRs).

I then confirmed a reboot by checking the Upcoming Recordings (fka To-Do List) and seeing that the number was much lower than before (it always resets after a reboot).

I am definitely guessing what happened (and it may very well be actually what happened) is that the "Reset Required" prompt may have come up sometime overnight, and it eventually timed out and rebooted automatically. IIRC that prompt comes up when new software "plugins" have to be installed.

Would like to hear your thoughts, especially since I probably haven't talked to some of you reading this in a while (was a former CE member, left almost a year ago).

Thank you all in advance!
4 Replies · 140 views
Tom Speer
My HR54 blue light is on this morning. I think you ae right about the plugins. They are tweaking things in the customer National release. What version does your HR44 Genie have now? I think you are probably on the same varsion as the CE group today.
lordodogg
I believe mine says 0x1D7F
Tom Speer
That is what I have.
  • Like
Reactions: lordodogg
lordodogg
Happened again today & have new software, 0x1d88
zippyfrog
Pub Member / Supporter Lifetime Supporter
Last reply · posted in DISH Network Support Forum
Did anyone have a price increase today on their equipment? I own my VIP211k's, and they have been $5.00. My bill that I received last week shows the "add-ons" as being $5.00. However, I just logged into my Dish account, and my "add-ons" are now $10.00. Did the additional receivers go up by $5.00 recently?

As I mentioned, my last bill shows $5.00 and under the notes, nothing is mentioned about a price increase.
4 Replies · 57 views
zippyfrog
Never mind - according to chat, it seems like there is a glitch in their website. The prices for owned receivers are still $5.00.
zippyfrog
However, when I make a change (tried to add the Columbian pack for $2 so I could generate my bill) and there is a new line - it says "Access for TV" - whereas previously that line item was not there. I hope they aren't charging $5.00 for the initial TV now...

1781191675068.webp
  • Like
Reactions: charlesrshell
T
Apparently it's not an "owned receiver" fee but rather an extension fee that's applied to 2nd and subsequent viewing. Maybe that played into their decision to force a box at every TV- garnering those fees
zippyfrog
Apparently it's not an "owned receiver" fee but rather an extension fee that's applied to 2nd and subsequent viewing. Maybe that played into their decision to force a box at every TV- garnering those fees
Possibly. In theory, $9 of the base pack has a rental fee built in. But now is this $5 a chance to get a little more? I don't know for sure. According to chat, it is a glitch and will be resolved in a timely manner, but we shall see. Part of my thinks there is a going to be a new charge, whether it is now or this fall. Here in Illinois, the law requires we are given 30 days notice of any fee changes, but I have not been given anything.

1781195549844.webp
  • Like
Reactions: charlesrshell
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in The Chit Chat Club
Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne


Get it?


An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
67106 Replies · 2662273 views
  • Like
Reactions: c-spand
ClarkGable
No Time - The Guess Who
  • Like
Reactions: sdfntx
harshness
Time After Time - Cyndi Lauper
sdfntx
Right on Time - Brandi Carlile
gms49ers
Time Stand Still - Rush
Bobby
I Can't Help It (If I'm Still In Love With You) - B.J. Thomas
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in SatelliteGuys Support Center
Our DNS provider is encouraging us to enable DNSSEC on our domains for added security.

I have gone ahead and enabled it, and am told it may take anywhere from 90 minutes to 24 hours for it to take effect.

Hopefully doing this does not harm the site in any way. (It shouldn't) but if it does, you will then know why and I will revert the settings.

But from what I am reading it should be ok. so just giving a warning as I have screwed up DNS stuff in the past. :D
1 Replies · 33 views
Scott Greczkowski
Doing my checks it appears the changes have gone through... and we are still here. (Phew!)
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in SatelliteGuys Support Center
Due to security concerns and the fact that the Tapatalk Plugin for Xenforo is no longer being updated we have removed Tapatalk support from SatelliteGuys.

For those who were using it we recommend using our PWA App instead which is faster and does not have all the spam Tapatalk had. Below is a graphic showing how to add SatelliteGuys to your devices home screen. (While iOS is shown the process is mostly the same for Android.)

add_to_home.gif

Thanks for your understanding. :)
7 Replies · 187 views
Foxbat
Thank you, Scott, for adding years to my Life and dropping my BP a few millimeters! Money well spent…
dweber
Thank you, Scott, for adding years to my Life and dropping my BP a few millimeters! Money well spent…
What is PWA app? PWA utilities seem to be a Spanish app. I hope you are seeing this since nothing seems to be working. I will miss SatelliteGuys. Tapatalk worked well. The Siri browser doesn't seem to work well.
  • Like
Reactions: charlesrshell
Peter Parker
Thank you, Scott, for adding years to my Life and dropping my BP a few millimeters! Money well spent…
Hooray!
  • Like
Reactions: charlesrshell
Peter Parker
What is PWA app? PWA utilities seem to be a Spanish app. I hope you are seeing this since nothing seems to be working. I will miss SatelliteGuys. Tapatalk worked well. The Siri browser doesn't seem to work well.
Do you mean the safari browser?
Foxbat
What is PWA app? PWA utilities seem to be a Spanish app. I hope you are seeing this since nothing seems to be working. I will miss SatelliteGuys. Tapatalk worked well. The Siri browser doesn't seem to work well.
Actually, PWA stands for "Progressive Web Application" and is basically just saving a site's homepage to your desktop where it appears as an "App" with the rest of your smartphone's Apps.
1781162703297.webp
  • Like
Reactions: charlesrshell
Scott Greczkowski
A PWA is a custom version of SatelliteGuys which is optimized for mobile devices. While it may look like the website, its actually different so that only the files needed for mobile are sent, meaning its a much faster experience all around.

TapaTalk is essentially dead. It was written for PHP 5.4 and we are now running PHP 8.4. There have been a LOT of PHP security updates since then and since Tapatalk for Xenforo has not been updated in a long long time it is not the safest idea to keep running it.

In addition those trying to view the site on their mobile devices using a browser were getting spammed on the top of the screen for people to install TapaTalk, this ad in some cases would take up 20% of the users screen. We could get rid of that ad but we would have to pay $20 a month to get rid of it.

Screenshot 2026-06-11 085611.webp



In addition TapaTalk could and was inserting their own ads on SatelliteGuys in the app which only benefitted them, SatelliteGuys was not paid for those ads they were displaying on our site. Again we could pay to get rid of those ads.

Screenshot 2026-06-11 085641.webp


And here was the cost of the Premium Tier.

Screenshot 2026-06-11 085701.webp


Now to make matters worse Tapatalk recently announced that they are going to start charging users of the app 99 cents a month to continue using it.

Screenshot 2026-06-11 090141.webp



So soon you would be paying them each month to access SatelliteGuys via their app, again all the money going to them... and you would still see all their ads too.

Tapatalk was a great program which we run for many many years, and for a long time we DID pay for the premium tier. But now with such a small offset using it (My numbers show a total of 6 members) it wasn't work paying for any longer.

In addition Tapatalk was sold to a different owner who made lots of promises of improvements and updates but then that owner has been really radio silent since, instead they have been letting TapaTalk rot on the vine.

If you visit their support forum at https://www.tapatalk.com/groups/tapatalksupport/ you will see there is not much going on, in fact most of the support questions posted there go unanswered.

Please give the PWA a try, I was a die hard Tapatalk user myself but now only use the PWA on devices. It is a much better all around experience, with no bloatware or additional ads based on your user membership level.

I don't have an android phone so I could not make a graphic showing you how to add SatelliteGuys PWA to your phones apps or home screen. But here is a site that explains how to do it on all kinds of devices. How to Install a PWA on iOS, Android, Windows & Mac [2025 Guide]

The above link also explains PWA's better as well. :)

If Tapatalk were to update their plugins so we know we are more secure and up to date and allow us to remove the "Smart Banner" without having to pay $20 a month, we would consider adding it back. I don't even care about their ads, as if a user wants to use their app and is willing to sit through their ads in order to use that app then I am ok with it.

But hopefully that explains better why it was removed. It was not done to cut anyone off from the site. :) Please give the PWA a try.
NYDutch
A PWA is a custom version of SatelliteGuys which is optimized for mobile devices. While it may look like the website, its actually different so that only the files needed for mobile are sent, meaning its a much faster experience all around.

TapaTalk is essentially dead. It was written for PHP 5.4 and we are now running PHP 8.4. There have been a LOT of PHP security updates since then and since Tapatalk for Xenforo has not been updated in a long long time it is not the safest idea to keep running it.

In addition those trying to view the site on their mobile devices using a browser were getting spammed on the top of the screen for people to install TapaTalk, this ad in some cases would take up 20% of the users screen. We could get rid of that ad but we would have to pay $20 a month to get rid of it.

View attachment 191729


In addition TapaTalk could and was inserting their own ads on SatelliteGuys in the app which only benefitted them, SatelliteGuys was not paid for those ads they were displaying on our site. Again we could pay to get rid of those ads.

View attachment 191730

And here was the cost of the Premium Tier.

View attachment 191731

Now to make matters worse Tapatalk recently announced that they are going to start charging users of the app 99 cents a month to continue using it.

View attachment 191732


So soon you would be paying them each month to access SatelliteGuys via their app, again all the money going to them... and you would still see all their ads too.

Tapatalk was a great program which we run for many many years, and for a long time we DID pay for the premium tier. But now with such a small offset using it (My numbers show a total of 6 members) it wasn't work paying for any longer.

In addition Tapatalk was sold to a different owner who made lots of promises of improvements and updates but then that owner has been really radio silent since, instead they have been letting TapaTalk rot on the vine.

If you visit their support forum at https://www.tapatalk.com/groups/tapatalksupport/ you will see there is not much going on, in fact most of the support questions posted there go unanswered.

Please give the PWA a try, I was a die hard Tapatalk user myself but now only use the PWA on devices. It is a much better all around experience, with no bloatware or additional ads based on your user membership level.

I don't have an android phone so I could not make a graphic showing you how to add SatelliteGuys PWA to your phones apps or home screen. But here is a site that explains how to do it on all kinds of devices. How to Install a PWA on iOS, Android, Windows & Mac [2025 Guide]

The above link also explains PWA's better as well. :)

If Tapatalk were to update their plugins so we know we are more secure and up to date and allow us to remove the "Smart Banner" without having to pay $20 a month, we would consider adding it back. I don't even care about their ads, as if a user wants to use their app and is willing to sit through their ads in order to use that app then I am ok with it.

But hopefully that explains better why it was removed. It was not done to cut anyone off from the site. :) Please give the PWA a try.
I just installed the PWA on my Android phone. It was pretty easy to do, and now I'm posting this from my phone. Thanks, Scott!
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in SatelliteGuys Support Center
As you may have noticed we are doing a Fund Raiser for SatelliteGuys!

As many of you know I have been paying for a majority of the operation of the site out of my own pocket for awhile now. Now looking at things we have a number of renewals coming up that I could use some help with. These renewals include the license renewal for our Forum Software, Renewal of a number of our add on's the site uses, renewal of domain names etc.

I have set a goal of $400.00 - any extra that comes in will just go to fund the operations of the site. None of the money will go to me (I tried BuyMeACoffee a few months ago, and they denied me saying they do not do business with Satellite Piracy sites... which we are not... hell we host the beta programs for both DISH and DIRECTV here...)

Anyways... if you would like to help out please click the link below.


Thank you in advance. :)
18 Replies · 565 views
Scott Greczkowski
I planned on removing it today, but then my fathers car broke down and I had to drive him all around to get his stuff done. Then I had a doctors appointment after that which was annoying...

Dr asks me if I have had any changes, so I tell him something wrong with me that started a month or so ago and his reply back is, that it sucks to get old... I hate that. Why ask me. if your going to come back with a smart ass answer.

Anyays I hope to get rid of Tapatalk tomorrow. :)

And we had more people donate today, thank you! The extra money is going to future expenses since things like add ons don't expire at the same time.

THANK YOU, THANK YOU, THANK YOU AGAIN!
T
Yeah, dr's...joint pain? Your joints are wearing out. It hurts when I do this...don't do that
comfortably_numb
Dr asks me if I have had any changes, so I tell him something wrong with me that started a month or so ago and his reply back is, that it sucks to get old

No excuse for a flippant response like that from a doctor! I'd be looking for a different one.
Scott Greczkowski
Tapatalk has been removed.

I have added a new feature which is a work in progress called "Social Feed" which displays the forums Facebook style. Its nice for people who like that, but needs work. But i have been watching this one for awhile and the author is being really responsive to suggestions and adding them. So if you have any please let me know and I can pass them along. :)
navychop
😍
  • Like
Reactions: charlesrshell
Scott Greczkowski
We got more kind donations yesterday! Again a very big thank you to everyone for your support!
dfergie
Staff member HERE TO HELP YOU!
Last reply · posted in The Sports Section
111 Replies · 2726 views
  • Like
Reactions: Foxbat and meStevo
Foxbat
Awesome pictures, Yespage! Thanks!

I caught the end of the four hour race on YouTube so I wasn't "spoiled", but got to see the exciting last lap action in the TCR division!
Y
Awesome pictures, Yespage! Thanks!

I caught the end of the four hour race on YouTube so I wasn't "spoiled", but got to see the exciting last lap action in the TCR division!
I heard on the radio, after the final pitstop, Turner Motorsport were resigned to second place. 'You're in second. Don't worry about it. First is McLaren, we aren't catching them.'
  • Like
Reactions: Foxbat
Y
Caught up to the 500... err... k in St. Louis. What a race! Andretti Motorsport were doing very well with Ericsson and Kirkwood, meanwhile Power was moving up the grid. Veekay started cautiously. He was working the tires just right, becoming more lethal later in the stint. Rasmussen was racing likewise, not nearly as insane as he has in the past. Palou was leading the race, in a shocker to all. Caio Collet was having a wonderful ride, making Ferucci potentially sweat a bit. Rain came, rain went, rain came, rain went. Generally mild sprinkles, but enough to pause racing on an oval.

Palou would kind of send Siegel into the wall. Siegel really didn't do much wrong. As he noted, you have to turn at some point. Palou had acres of room below and Siegel might have had his ticket out of Indycar stamped. Dixon was doing the fuel thing and got busted twice by yellows, not pitting before the flag came out. Then the most critical happened... Palou ran out of gas on pit lane, effectively giving Newgarden the race lead and win. Newgarden had a very early pit, so he was able to slide in, get service and go. Meanwhile, everyone else was confused and stuck behind Palou for a bit. Once people figured what was happening, Newgarden had a major advantage of several seconds. Newgarden wouldn't look back and when it went green again, he'd hold the lead for the win.

Massive credit to Juncos Hollinger who bested Penske in getting Veekay out before Malukas in a transition that was oddly bizarre. I haven't had time to check, but I'm wondering if Veekay was about to run out of fuel or cut a tire. He was charging late in a stint, got up to fifth, and then tailed back for a few laps to 10th or 11th. It looked like it was over. Went into the pits, and after the pitting sequence was over, Veekay was well inside the top ten again. It was weird. And he charged, getting up to fourth. He made a late move on Rasmussen, but Rasmussen held his position with some great driving. In fact, there was a ton of incredible racing passing, not passing all race long. Veekay would finish 4th. A podium would have been awesome, but it is a great outcome for a guy who hopefully will get a break with a big team. We saw what Veekay could do with a Honda last season with fuel save, imagine replacing Simpson on Ganassi and having speed to go with fuel saving. His 6th at Indy and 4th at St. Louis get him up to 13th in the points standings and only 5 points outside of the top 10.

Ericsson finished second, resigned to finishing behind the current best in the world guy on a short oval. Rasmussen got the final step on the podium, a nice rebound to what has been an otherwise bad year for him, and a good reward to ECR who just extended his contract.
Y
They raced USAC cars at Daytona once. Once! People died. Aj Foyt said 'f this', and left after the first go around. AJ freaking Foyt thought it was crazy! And cars weren't nearly as fast as they are now.

I think they tried Talladega once too.
Y
LeMans qualifying on going. WEC has d9ne a great job expanding the automotive company entries. Even without Porsche, a large nunber of manufacturers.
Peter Parker
Supporting Founder Lifetime Supporter
Last reply · posted in Computers and Gadgets
I have had good experiences with Brave but lately I am frustrated with it.

Now when I launch the app it shows a box at the bottom asking if I want to go back to the last opened page. It is in conveniently located and I would prefer to eliminate it.

Does anyone know how to do this?

Please let's not sidetrack the discussion into an exploration of why I don't care for it or a lecture about all the wonderful aspects of the feature. I just do not care for it.
3 Replies · 74 views
b4pjoe
I don't have an Android phone so I don't know if this will apply to the Brave settings on your android device but it works on the desktop for me.

Change this setting to either startup to a different website or a new tab page. I have mine set to open to google.com instead of where I left off and it doesn't ask me at the next startup if I want to open the last opened page unless it crashed.

Screenshot 2026-06-10 at 6.46.20 PM.webp
Peter Parker
I don't have an Android phone so I don't know if this will apply to the Brave settings on your android device but it works on the desktop for me.

Change this setting to either startup to a different website or a new tab page. I have mine set to open to google.com instead of where I left off and it doesn't ask me at the next startup if I want to open the last opened page unless it crashed.

View attachment 191721
Thank you for trying to help. However thrse choices do not appear in Android. There is a setting for "New Tab Pages" that is similar but does not include your choice. I have tried all of the existing entries with no success
  • Like
Reactions: b4pjoe
Juan
Something like this maybe


Option 2: Set a custom Home button URL
  1. Click the menu icon in the top-right corner and select Settings.
  2. Click on Appearance in the left sidebar.
  3. Toggle on the Show home button switch.
  4. Under the home button settings, select the option to Enter custom web address and type in your preferred website. [1, 2, 3, 4, 5]