Social Feed

C
Last reply · posted in DISH Network Support Forum
We have a 211k receiver in the master bedroom. My wife and I have talked about setting up a TV on the back patio. We would like HD content and access to our Dish programming. I have explored various options for doing this and there are positive and negatives for each of them (splitting the HDMI from the 722k in the living room, using wireless HDMI, etc.). We do not want to add another receiver.

Would there be any problem with running an extra coax cable from the satellite location to the back patio and using the same satellite connection that the coax running to the master bedroom uses? When we want to watch TV outside, I would just "unplug" the master bedroom coax and "plug in" the back patio coax and carry the 211k outside and hook it up at the back patio. Any reason this would not work?

I like this option because it would be easy to run the coax outside around the house and the signal would be independent of the living room TV. I don't have an easy way to run HDMI to the back patio from the 722k.
31 Replies · 4414 views
aaronwt6
Any way you could just run a wire from the dish itself to the patio? You should have a 3rd output on the dish. That was its a simple as just relocating the receiver each time.

Maybe that's what you were intending and I misunderstood but it sounds like you were planning on running the wire from the bedroom to the patio.
C
Any way you could just run a wire from the dish itself to the patio? You should have a 3rd output on the dish. That was its a simple as just relocating the receiver each time.

Maybe that's what you were intending and I misunderstood but it sounds like you were planning on running the wire from the bedroom to the patio.

That is basically what I am doing. The coax to the bedroom comes outside and is attached to a device (I can't remember what it is. It may be a switch) which is connected to the Dish by coax. I was going to run another line of coax from that same point to the back patio and just switch the coax connections when we watched TV outside. This will be an easy outside run.

The switching would be easier if I could find an A/B switch that does this. All of the A/B switches I've found are 2 input/1 output. Can I use an A/B switch in reverse? That way I could just flick the switch to change the output path.

Are you saying I should be able to connect directly to the Dish and not worry about switching?
Stargazer
If you had a Hopper and a Joey then ran the Joey wireless then that would be the best bet but he would have to swap out his current equipment in order to get the Hopper. This would get him his HD feed wirelessly without running any wires to any place he wants to place that Joey. They allow you one 211 on the account though don't they with the Hopper?
lucky86
You can have a purchased 211/211k/411 on a Hopper account for use with a Tailgater.
C
If you had a Hopper and a Joey then ran the Joey wireless then that would be the best bet but he would have to swap out his current equipment in order to get the Hopper. This would get him his HD feed wirelessly without running any wires to any place he wants to place that Joey. They allow you one 211 on the account though don't they with the Hopper?

I considered that option, but didn't want to do it at this time. I will probably look at it in the future. I love that the Joey can work wirelessly and hope it is officially supported in the future.
Dishman1978
That is basically what I am doing. The coax to the bedroom comes outside and is attached to a device (I can't remember what it is. It may be a switch) which is connected to the Dish by coax. I was going to run another line of coax from that same point to the back patio and just switch the coax connections when we watched TV outside. This will be an easy outside run.

The switching would be easier if I could find an A/B switch that does this. All of the A/B switches I've found are 2 input/1 output. Can I use an A/B switch in reverse? That way I could just flick the switch to change the output path.

Are you saying I should be able to connect directly to the Dish and not worry about switching?

No. a/b switch will not work properly with a satellite feed.

Connect.it directly to the dish.
Jimmerinwi
Your best bet is to run the additional line to your patio instead of using the additional output in the 211 seeing the remote is ir and you would need to go to the receiver to change channels.

Sent from my iPhone using SatelliteGuys
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in The Chit Chat Club
Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne


Get it?


An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
68632 Replies · 2679003 views
  • Like
Reactions: c-spand
H
PEOPLE Are Strange-The Doors
Bobby
PEOPLE Are Strange-The Doors

You're Still A Young Man - Tower Of Power
No Match, back to:
People Are Strange - The Doors




Isn't Life Strange - The Moody Blues
FTA4PA
Strange Days - Nazareth
gms49ers
Dancing Days - Led Zeppelin
dishstaller
Dancing in the Street - Van Halen
long_time_Dish
Bakers Street - Gerry Rafferty
osu1991
Pub Member / Supporter
Last reply · posted in Movie Talk
52 Replies · 10063 views
long_time_Dish
Also watched part 2 about a week or so ago after rewatching part 1. It's not as faithful to the book as I was hoping for. Part 1 stayed fairly faithful to the novel, but part 2 took some liberties that I felt were rather excessively non-novel. It looks like a prequel series will happen before part 3. My issue is: there's no prequel that was written as a novel, so what will it be pulled from? Or will it just be "based loosely" on the novel?
K
Also watched part 2 about a week or so ago after rewatching part 1. It's not as faithful to the book as I was hoping for. Part 1 stayed fairly faithful to the novel, but part 2 took some liberties that I felt were rather excessively non-novel. It looks like a prequel series will happen before part 3. My issue is: there's no prequel that was written as a novel, so what will it be pulled from? Or will it just be "based loosely" on the novel?
There is a bunch of other Dune written by Kevin J Anderson and Brian Herbert (Franks son). I think the series in production is taken from one of their books about the Bene Gesserit.
long_time_Dish
There is a bunch of other Dune written by Kevin J Anderson and Brian Herbert (Franks son). I think the series in production is taken from one of their books about the Bene Gesserit.
Correct. I've read all of them (yes, it took awhile, better part of a year, in my spare time). And they can't really consider or classify a series about the Bene Gesserit as a prequel. Sure, I suppose they can call it that, if they want to, because it begins before the time of Paul Atredies, but it's still a stretch. It's a Dune-related novel, not a prequel as we generally think of prequels...
TWiT Tech Podcast Network
· posted in TWiT Tech Podcast Network
0 Replies · 6 views
TRG
TRG
Pub Member / Supporter
Last reply · posted in Local Radio Discussion
20 Replies · 586 views
dishdude
It's probably been 2 decades since I've listened to an AM radio station. Very rarely listen to FM any more.
  • Like
Reactions: reubenray and Jimbo
Jimbo
I am 1 that wants the AM to Stay ....
That said, since '08 I have had Sat radio available to me ... I think I have turned on AM 3 or 4 times, just to see if its still there.

Fwiw, if theres a Major disaster or bad weather or whatever, the chances of me finding out about it by going to the AM side of the radio is SLIM and None.
Even FM, I haven't really had on since '13ish, I may turn it on from time to time, just to see if its still there.
harshness
Fwiw, if theres a Major disaster or bad weather or whatever, the chances of me finding out about it by going to the AM side of the radio is SLIM and None.
Automation has seen to that. You can't get evening drive traffic reports where I live, much less disaster reports.
dishstaller
Very rarely listen to FM any more
That goes for a lot of people. I've been advertising on radio for more than a decade now and am very familiar with this subject. While it is still a valuable tool, it has far less impact than it did just a few years ago. The best reaction I get is from a local Country music station....they play a mix of older and newer music and have a very big footprint.
  • Like
Reactions: Mr Tony
Jimbo
That goes for a lot of people. I've been advertising on radio for more than a decade now and am very familiar with this subject. While it is still a valuable tool, it has far less impact than it did just a few years ago. The best reaction I get is from a local Country music station....they play a mix of older and newer music and have a very big footprint.
Do you do any Ad's on Satellite ?

If Not, why not, because it's not Local ?
dishstaller
Do you do any Ad's on Satellite ?

If Not, why not, because it's not Local ?
No, just regular FM stations. One is the country station I mentioned and the other is a Talk Radio station which used to get fantastic results but honestly, since the death of Rush Limbaugh, talk radio just doesn't do as well. There were two guys who had an early morning show which was hugely popular here in the southeast but one of them retired a couple years ago and the show just doesn't garner the same numbers as it used to.
TheForce
Supporting Founder Pub Member / Supporter
Last reply · posted in The Phone & Tablet Zone
Apple Fall Hardware Event takes place today, September 9, 2026, at 10:00 a.m. PT / 1:00 p.m. ET. It marks the debut of new CEO John Ternus and the expected reveal of Apple's first foldable phone.
135 Replies · 1642 views
comfortably_numb
Can't remember if I've posted this yet..


View: https://www.youtube.com/watch?v=nfL5seXJyWU
  • Haha
Reactions: slow_poke_pete
Foxbat
IFixIt has published their Teardown and they had some positive things to say about the iPhone Duo. It still showed some dust ingress into the hinge assembly but seemed otherwise well-sealed.
​

But with a considerable number of reports of the main screen dying with similar failures, AppleCare+ should be a no-brainer for this phone.
S

most carriers do. that's why they send updates that slow phones down!! i buy unlocked phones no effect to me
S
IFixIt has published their Teardown and they had some positive things to say about the iPhone Duo. It still showed some dust ingress into the hinge assembly but seemed otherwise well-sealed.
​

But with a considerable number of reports of the main screen dying with similar failures, AppleCare+ should be a no-brainer for this phone.

hope you have apple care a screen job is 1000.00 :oops:. can we say over priced garbage!!!
harshness
Gone are the days when Apple "perfects" what debuted years earlier on an Android phone.
comfortably_numb
Gone are the days when Apple "perfects" what debuted years earlier on an Android phone.

Or better yet, innovate something "completely revolutionary!"
SkyWatcher57
Pub Member / Supporter
Last reply · posted in Free To Air (FTA) Discussion
Hello folks, well my luck ran out last week with a nasty thunderstorm and after 39 years here, finally took a hit. Now, the FTA receivers I had for some years worked great until now. Recently picked up a fairly cheap receiver, online, KOQIT and seems to be good, but for the life of me, I cannot get the HDMI output to work with 3 of my Samsung monitors. I can hook it up to my Samsung TV and its HDMI input and it works fine. The 2 receivers I lost also worked fine with them, so am I going crazy? anyone have come across this or have any suggestions? And, since this is a somewhat cheap unit but works, what is everyone out there using for receivers these days? without breaking the bank? I enjoy watching FTA TV, so I will invest more if needed, what is a really good, detailed unit these days. I'm so use to watching a few of them HD channels. Right now I'm down to composite hookups, yuck! Any help or info would be greatly appreciated. Thanks Frank :rolleyes:
47 Replies · 1300 views
(((Garyd)))
Hello folks, well my luck ran out last week with a nasty thunderstorm and after 39 years here, finally took a hit. Now, the FTA receivers I had for some years worked great until now. Recently picked up a fairly cheap receiver, online, KOQIT and seems to be good, but for the life of me, I cannot get the HDMI output to work with 3 of my Samsung monitors. I can hook it up to my Samsung TV and its HDMI input and it works fine. The 2 receivers I lost also worked fine with them, so am I going crazy? anyone have come across this or have any suggestions? And, since this is a somewhat cheap unit but works, what is everyone out there using for receivers these days? without breaking the bank? I enjoy watching FTA TV, so I will invest more if needed, what is a really good, detailed unit these days. I'm so use to watching a few of them HD channels. Right now I'm down to composite hookups, yuck! Any help or info would be greatly appreciated. Thanks Frank :rolleyes:
Take the cover off, show me pics of the board of the bad one and also the bottom of the board. I'm an old hardware electronics tech plus a satellite dealer; I fixed a lot of FTA and regular receivers. I may be able to fix it for you. And yes, they got hit by lightning; it's best to email me the pics at diamondsatellite@snet.net or call me at 203-232-8888. I give you a 50-50 chance of fixing it; I do have spare parts. my phone is a fliptop phone
Gary
  • Like
Reactions: navychop
S
Hello folks, well my luck ran out last week with a nasty thunderstorm and after 39 years here, finally took a hit. Now, the FTA receivers I had for some years worked great until now. Recently picked up a fairly cheap receiver, online, KOQIT and seems to be good, but for the life of me, I cannot get the HDMI output to work with 3 of my Samsung monitors. I can hook it up to my Samsung TV and its HDMI input and it works fine. The 2 receivers I lost also worked fine with them, so am I going crazy? anyone have come across this or have any suggestions? And, since this is a somewhat cheap unit but works, what is everyone out there using for receivers these days? without breaking the bank? I enjoy watching FTA TV, so I will invest more if needed, what is a really good, detailed unit these days. I'm so use to watching a few of them HD channels. Right now I'm down to composite hookups, yuck! Any help or info would be greatly appreciated. Thanks Frank :rolleyes:
a good surge protector will help to.
  • Like
Reactions: SkyWatcher57
SkyWatcher57
Take the cover off, show me pics of the board of the bad one and also the bottom of the board. I'm an old hardware electronics tech plus a satellite dealer; I fixed a lot of FTA and regular receivers. I may be able to fix it for you. And yes, they got hit by lightning; it's best to email me the pics at diamondsatellite@snet.net or call me at 203-232-8888. I give you a 50-50 chance of fixing it; I do have spare parts. my phone is a fliptop phone
Gary
Hi Gary, still working on getting you those
Hi Gary, just saw this, ok, I'll grab some pics tomorrow and post them. thx
Still working getting you those pictures, nice weekends means yard work and fall prep, thanks
  • Like
Reactions: (((Garyd)))
k4otl
Anybody know how to add "hidden" audio channels like for 101 W Ku or 105W C band on these recvr's? I've exported the database file but don't have anything that will read or edit it.
cyberham
For 105W C, you scan in the Westwood tp normally. Then select the audio channel you want. Not necessary to manually enter. On 101W, you must manually enter.
k4otl
For 105W C, you scan in the Westwood tp normally. Then select the audio channel you want. Not necessary to manually enter. On 101W, you must manually enter.
Seems like I remember that now, with my V9 I manually entered anyway on 105, easier for me to pick the channel later :)