Social Feed

A
Last reply · posted in FTA Receiver / Equipment Support
I have a Time machine (MAC) as my main Wifi router throughout my home. I have not been able to get the AZbox Premium Plus to connect. I have setup all the parameters correctly as far as I know..The Azbox recognizes my Router when I go to into wifi. I have the latest manual and have read through it and can not find any particular networking answers for the Time Machine. I also have the Questions manual updated, and have not been able to find any info..
I setup the wifi with the ip's and all the details as per the latest Manual using static ip and the Gateway as my
Router's base address.. I am using the same ip address as the router has when I go into network preferences on the router..
I have the DNS 1 the same as what the router is using as well.
The way I understand it, is that the Router is supposed to assign me automatically an ip...but perhaps I am wrong.. I tried to assign my own as per the manual as 192.168.1.102 and that does not work either.
So I have wifi, The Az knows it is there and recognizes it, but it will not connect..
Does anyone here have experience with the Mac Time Machine and AZBOX internet setup?? I would appreciate any help I can get, and I have read through and searched these forums as best as I can before asking.. Thanks for your help, HB
8 Replies · 3087 views
Lone Gunman
Did you try setting your router to assign a static IP address to your AZBox? I have a Cradlepoint router and I did this for both my AZs and it worked well. I used 192.168.0.145 for one and .146 for the other so I'd know exactly which one I was accessing on the network when I FTP'd to it.
A
Thanks to all for the input..
I did find, in Airpot utility that the DHCP Range is from .2 to .200 So I have been trying assigning much higher #'s than my other devices are using...
I see that the other devices are using from .21-.28 so I went to the .30's up to .190's just probing and no luck. That is in "Off-Bridge Mode"
In Airport Utility All of my devices are receiving in" OFF-Bridge Mode" at "Connection Sharing" under "Internet" tab.
My connection to the Time Capsule is Ethernet cable Fiber Optic.
I see the options under "Connection Sharing" are:
1. Share a public ip address ( which does not work even after setting the DHCP ranges , The Time Capsule will not start)
2. Distribute a Range of ip Addresses ( Which does not work after setting different parameters as per the pop-up's asking for variable ranges, etc.)
3. OFF (Bridge Mode) The only setting that is working on all my devices with the AZBOX being the exception
So I am still stuck.
I really need to touch base with someone using AZ with Time Capsule..I think that is the only way, and see what they are doing..I have spent hours at it today and last eve. Never give up!!! Thanks for the input..I really want to keep the Time Capsule as my Main router, but I will now go to the CradlePoint and work with that just to see what is up..
Any other ideas anyone???
Thanks again for the input, keep up the good work all here at Sat guys..HB
catamount
I just went to fibre-optic about three weeks ago. My ISP provides their own modem/router combo. I wanted to keep the apple base station for wireless. I turned off the wireless on the actiontec and ran an ethernet cable to the apple. I had to put the apple in bridge mode.

I run wired to my Azbox minime, which works fine, but the Isp actiontec hands out the dhcp addresses. The apple is set to hand out dhcp wireless addresses. Is your time capsule your "second" router also? I ask because I see you are using 192.168 addresses, whereas apple normally uses 10.0.1.1. I had to switch to 192.168 addresses with fibre because of the existing subnet.

Did you try another usb wifi on your AZbox? Sorry, but no experience with azbox wireless. I don't mind checking some settings in my airport utility if you need me to.

Catamount
A
I just went to fibre-optic about three weeks ago. My ISP provides their own modem/router combo. I wanted to keep the apple base station for wireless. I turned off the wireless on the actiontec and ran an ethernet cable to the apple. I had to put the apple in bridge mode.

I run wired to my Azbox minime, which works fine, but the Isp actiontec hands out the dhcp addresses. The apple is set to hand out dhcp wireless addresses. Is your time capsule your "second" router also? I ask because I see you are using 192.168 addresses, whereas apple normally uses 10.0.1.1. I had to switch to 192.168 addresses with fibre because of the existing subnet.

Did you try another usb wifi on your AZbox? Sorry, but no experience with azbox wireless. I don't mind checking some settings in my airport utility if you need me to.

Catamount

Cata, thanks for your help here.
No, I do not have a 2nd router.. I made a mistake when I told you fiber optic input..Only last month I disconnected my fiber optic cable and converter because they "tripled" the monthly rate...Believe it or not here in Honduras they want $235 a month for 1mg download speed...Is that crazy or what?? So I changed to another provider which is wireless reception now... Still a high price at $75 a month for only 2 MG speed... Count your blessings up there,It's costly to have any service here at all..
So I am on a subnet and basically the Time Capsule is a second router, as the ip's router would be the first...right?? So that is why I am 192.168.
Looking back into my fiber optic data records that I saved for my set up, I was indeed using an ip of 10.70.21.2
Same subnet mask as I use now and DNS servers 200.110.244.2 which is Guatemala I think. As the optic cables all originated in Guatemala..
So essentially I am using 2 routers here... I believe .
I would appreciate it if you could show me your settings in Time Capsule.. I have not had a chance yet to hook-up the Cradlepoint 4g USB router that I was using a couple years ago..The Time Capsule is such a good machine.. It's just way better than all routers I've had, so I imagine that is why I'm slow at moving toward the Cradle Point again, I don't even want to think of another router...but I will, hopefully this weekend when I get some time..
If you could list all of your TC settings for me in Airport Utility, that would be a big help, perhaps to diagnose what is going on, and If you would list the AZBOX settings as well so I can compare that...
Thanks for your help...
Also, being you are using Mac's have you ever found a decent AZ editor for channel lists ??? I can not find anything for MAC. Thanks again for your time and effort here.I really appreciate it.. HB
catamount
The only Mac product I have is the router. Right now, I'm running Windows machines, although I've run various linux distros in the past. Never tried an AZ editor, but I doubt there is one for a Mac.

I tried to grab some airport utility screenshots from the desktop, but wouldn't let me. I'll type out some settings over the next day or two and send them to you via PM.

The only other advice I have is reboot, reboot! A lot of times just going from wired to wireless on my laptop, I have to reboot both my laptop and Apple router to get internet access. It can be very frustrating, but once it's working the router is hard to beat!

Catamount
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in SatelliteGuys Support Center
As you may have noticed we are doing a Fund Raiser for SatelliteGuys!

As many of you know I have been paying for a majority of the operation of the site out of my own pocket for awhile now. Now looking at things we have a number of renewals coming up that I could use some help with. These renewals include the license renewal for our Forum Software, Renewal of a number of our add on's the site uses, renewal of domain names etc.

I have set a goal of $400.00 - any extra that comes in will just go to fund the operations of the site. None of the money will go to me (I tried BuyMeACoffee a few months ago, and they denied me saying they do not do business with Satellite Piracy sites... which we are not... hell we host the beta programs for both DISH and DIRECTV here...)

Anyways... if you would like to help out please click the link below.


Thank you in advance. :)
17 Replies · 461 views
Scott Greczkowski
I planned on removing it today, but then my fathers car broke down and I had to drive him all around to get his stuff done. Then I had a doctors appointment after that which was annoying...

Dr asks me if I have had any changes, so I tell him something wrong with me that started a month or so ago and his reply back is, that it sucks to get old... I hate that. Why ask me. if your going to come back with a smart ass answer.

Anyays I hope to get rid of Tapatalk tomorrow. :)

And we had more people donate today, thank you! The extra money is going to future expenses since things like add ons don't expire at the same time.

THANK YOU, THANK YOU, THANK YOU AGAIN!
Foxbat
Anyays I hope to get rid of Tapatalk tomorrow. :)
Dance Reaction GIF
T
Yeah, dr's...joint pain? Your joints are wearing out. It hurts when I do this...don't do that
comfortably_numb
Dr asks me if I have had any changes, so I tell him something wrong with me that started a month or so ago and his reply back is, that it sucks to get old

No excuse for a flippant response like that from a doctor! I'd be looking for a different one.
Scott Greczkowski
Tapatalk has been removed.

I have added a new feature which is a work in progress called "Social Feed" which displays the forums Facebook style. Its nice for people who like that, but needs work. But i have been watching this one for awhile and the author is being really responsive to suggestions and adding them. So if you have any please let me know and I can pass them along. :)
navychop
😍
  • Like
Reactions: charlesrshell
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in SatelliteGuys Support Center
Due to security concerns and the fact that the Tapatalk Plugin for Xenforo is no longer being updated we have removed Tapatalk support from SatelliteGuys.

For those who were using it we recommend using our PWA App instead which is faster and does not have all the spam Tapatalk had. Below is a graphic showing how to add SatelliteGuys to your devices home screen. (While iOS is shown the process is mostly the same for Android.)

add_to_home.gif

Thanks for your understanding. :)
1 Replies · 39 views
Foxbat
Thank you, Scott, for adding years to my Life and dropping my BP a few millimeters! Money well spent…
dfergie
Staff member HERE TO HELP YOU!
Last reply · posted in The Sports Section
110 Replies · 2671 views
  • Like
Reactions: Foxbat and meStevo
Foxbat
Awesome pictures, Yespage! Thanks!

I caught the end of the four hour race on YouTube so I wasn't "spoiled", but got to see the exciting last lap action in the TCR division!
Y
Awesome pictures, Yespage! Thanks!

I caught the end of the four hour race on YouTube so I wasn't "spoiled", but got to see the exciting last lap action in the TCR division!
I heard on the radio, after the final pitstop, Turner Motorsport were resigned to second place. 'You're in second. Don't worry about it. First is McLaren, we aren't catching them.'
  • Like
Reactions: Foxbat
Y
Caught up to the 500... err... k in St. Louis. What a race! Andretti Motorsport were doing very well with Ericsson and Kirkwood, meanwhile Power was moving up the grid. Veekay started cautiously. He was working the tires just right, becoming more lethal later in the stint. Rasmussen was racing likewise, not nearly as insane as he has in the past. Palou was leading the race, in a shocker to all. Caio Collet was having a wonderful ride, making Ferucci potentially sweat a bit. Rain came, rain went, rain came, rain went. Generally mild sprinkles, but enough to pause racing on an oval.

Palou would kind of send Siegel into the wall. Siegel really didn't do much wrong. As he noted, you have to turn at some point. Palou had acres of room below and Siegel might have had his ticket out of Indycar stamped. Dixon was doing the fuel thing and got busted twice by yellows, not pitting before the flag came out. Then the most critical happened... Palou ran out of gas on pit lane, effectively giving Newgarden the race lead and win. Newgarden had a very early pit, so he was able to slide in, get service and go. Meanwhile, everyone else was confused and stuck behind Palou for a bit. Once people figured what was happening, Newgarden had a major advantage of several seconds. Newgarden wouldn't look back and when it went green again, he'd hold the lead for the win.

Massive credit to Juncos Hollinger who bested Penske in getting Veekay out before Malukas in a transition that was oddly bizarre. I haven't had time to check, but I'm wondering if Veekay was about to run out of fuel or cut a tire. He was charging late in a stint, got up to fifth, and then tailed back for a few laps to 10th or 11th. It looked like it was over. Went into the pits, and after the pitting sequence was over, Veekay was well inside the top ten again. It was weird. And he charged, getting up to fourth. He made a late move on Rasmussen, but Rasmussen held his position with some great driving. In fact, there was a ton of incredible racing passing, not passing all race long. Veekay would finish 4th. A podium would have been awesome, but it is a great outcome for a guy who hopefully will get a break with a big team. We saw what Veekay could do with a Honda last season with fuel save, imagine replacing Simpson on Ganassi and having speed to go with fuel saving. His 6th at Indy and 4th at St. Louis get him up to 13th in the points standings and only 5 points outside of the top 10.

Ericsson finished second, resigned to finishing behind the current best in the world guy on a short oval. Rasmussen got the final step on the podium, a nice rebound to what has been an otherwise bad year for him, and a good reward to ECR who just extended his contract.
Y
They raced USAC cars at Daytona once. Once! People died. Aj Foyt said 'f this', and left after the first go around. AJ freaking Foyt thought it was crazy! And cars weren't nearly as fast as they are now.

I think they tried Talladega once too.
Gary Toma
Staff member Pub Member / Supporter Cutting Edge
Last reply · posted in DIRECTV Technical Resources Forum
The TPN Map Excel Presents all DIRECTV Channels:
National (50-States or wide/NAT+PR beams)
Local (Local-Into-Local or narrow/Spot beams)
Additional tabs provide:​
OTA the (Over-The-Air) Database
VOD (Video On_Demand) Records
Offline Records
Engr Records
Net Decoder a graphic presentation of all satellites and transponders
Domestic Satellites
@99W...... D11, D14
@101W.... D9S, D16
@103W.... D10, D12, D15
@110W.... D5
@119W.... D8​



See also

Understanding the TPN Map

Making Sense of the TPN Map Display Conventions
1968 Replies · 909008 views
D
DirecTV Satellite Transponder Updates for Jun 10 2026

Comparison of Transponder Data for Jun 10 2026 vs Jun 03 2026:


No changes in system tables for any transponder tuning parameters.

Changes to the use of defined transponders:

1 Transponder cleared of all Streams::
Net 15 TID 124 Beam NAT is a National Transponder on D15@103cb, TPN 1


Stream (PID) counts:

LIVE Streams​
National​
Spot Beams​
Count​
Change​
Count​
Change​
4K​
4​
HD​
270​
-2​
1397​
SD mpeg4
144​
2​
188​
SD mpeg2
440​
RB​
Audio​
89​
Push​
26​
Slate​
19​
1​
TEST Streams​
National​
Spot Beams​
Count​
Change​
Count​
Change​
4K​
HD​
1​
1​
1​
SD mpeg4
1​
SD mpeg2
RB​
Engr Work​
29​
-11​


The PID count Excel workbook provides much more count detail.

Newly updated tables of Streams on each transponder are available in the DataDigesters TPN Grids

More details of changes in individual channels will follow in the Weekly Analysis
and Gary Toma's Domestic TPN Map Excel files
Weekly Analysis soon
US Open golf set up
Info screens about watching NBA and Stanley cup games on Local Channels
Enjoy
DataDigesters
  • Like
Reactions: lordodogg
D
Weekly Analysis for 6/10/2026:
  • Like
Reactions: lordodogg
K
604 Pursuit HD is testing

Women's US Open Out, Men's US Open and World Cup in

The Vegas specific slate for KTNV is repurposing Dispute Slide 1 Test 9109
  • Like
Reactions: lordodogg
lordodogg
604 Pursuit HD is testing
Interesting. I remember that being HD-only for a bit a long time ago and then it was back to SD-only.
lordodogg
Interesting. I remember that being HD-only for a bit a long time ago and then it was back to SD-only.
looking at the old maps, that was from March 2017 to June 2019.
T
Last reply · posted in Over the Air Television By RabbitEars.Info
So I have recently setup Indoor OTA due to drop to Local from Dish, and found out reason why I have such bad signal is my Monitor now none of cable for my monitor near OTA or it cable going to TV, but the TV right above my Monitor maybe not even a foot.

If i have 3 to 2 bars with monitor off said channel for most part of perfectly watchable, but as soon my monitor is ON (show image of desktop or what ever) OTA going to TV halved that 3 to 2 bars become 1 and 2 if I lucky and channels start scrambling alot, and depending on what is being shown on monitor it might out right give no signal, and I can easily restore singal to being bad if change what show on monitor or bring back 3 to 2 bars if I turn monitor off or let it to to standby mode.

I have already disconnect every cable on TV except the OTA cable leaving just that so it not those cable. the Power cable for monitor and DP to DVI cable the monitor is using no where near that OTA cable either.

Any idea on how to fix this? moving my monitor isnt exactly an option neither is moving the tv and moving the OTA to other side room even with long cable dont fix this issue.

I have one those Leaf MoHu antennas 11x3 ones, I had same issue with one gateway mohu antennas the older one too
14 Replies · 312 views
comfortably_numb
Do you have any splitters or combiners in between the antenna and TV? That can cause issues, especially indoors.

I would get that antenna into the attic or outside if at all possible.

And we need your Rabbitears reception report to really be able to provide answers specific to your location-

  • Like
Reactions: Foxbat
T
Do you have any splitters or combiners in between the antenna and TV? That can cause issues, especially indoors.

I would get that antenna into the attic or outside if at all possible.

And we need your Rabbitears reception report to really be able to provide answers specific to your location-

no spilter is just for my tv


I get I just need to short out the monitor from kill the signal to the tv cause the monitor being on and show image basically castrates signal

I just moved wires around moved power cord away data cord and what not, and some made this issue worse just have my monitor on and show image was enough to just kill signal, I went and moved monitors data cable DP to DVI cable and it came back even if was still spotty at best, now I think it DP to DVI cable I using considering moving seem maninpulate how bad the signal that cable is still no where near OTA cable or any cables going to the tv, the tv and monitor are on the same surge protector though
Jimbo
no spilter is just for my tv


I get I just need to short out the monitor from kill the signal to the tv cause the monitor being on and show image basically castrates signal

I just moved wires around moved power cord away data cord and what not, and some made this issue worse just have my monitor on and show image was enough to just kill signal, I went and moved monitors data cable DP to DVI cable and it came back even if was still spotty at best, now I think it DP to DVI cable I using considering moving seem maninpulate how bad the signal that cable is still no where near OTA cable or any cables going to the tv, the tv and monitor are on the same surge protector though
Are these items all Grounded ?
You haven't defeated them ...
Make sure the outlet is grounded as well, if it's nothten nothing else is.
T
Are these items all Grounded ?
You haven't defeated them ...
Make sure the outlet is grounded as well, if it's nothten nothing else is.
Far as i know they are all ground as surge protector is grounded this particular mode APC PV11V3 has wiring/fualt light that should go on if it not grounded and it not on protection light is green and on too . I not very knowledge about all that electrical grounding so i just go by what it tells me, my other surge protecter has grounded light on I could probably just plug to same outlet this one is to see if actual grounded

Monitor has 3 prog power cord the TV is 2 prog


Sounds like there may be some RF coming from your monitor (presumed to be a computer monitor?) being picked up by the TV's proximity to the monitor.
Move the TV or the computer at least 5 ft away.
If it is cabling to monitor it would show up while the computer is on and whether the monitor is off or on.

Sadly moving the monitor (Asus VS248) is not really an option I would have move my entire room which I not about to do. Computer is under desk said monitor is on, but turn the computer off does stop signal from droping so long as monitor is on, as I test that by connecting my ps5 to that and it happened there too

I do know that Moving the DP to DVI cable under desk can and does effect the signal, depending on where that cable is I might have spotty signal or no signal out all with the monitor on. but soon as it is off signal is fine.

The DP to DVI cable is shielded and the coxial cable is a shielded RG6 cable

I will see about moving the monitor 5+ feet way just to see if proximity to tv is issue. but that wont really solve my issue cause moving desk and there for computer and monitor isnt really option

Maybe wrap the monitor in aluminum foil? Just as a test to see if it's radiating RFI that's overwhelming the OTA tuner. Obviously not a viable long-term fix.
worth try I see what happen when I get hand on some aluminum foil
Jimbo
Far as i know they are all ground as surge protector is grounded this particular mode APC PV11V3 has wiring/fualt light that should go on if it not grounded and it not on protection light is green and on too . I not very knowledge about all that electrical grounding so i just go by what it tells me, my other surge protecter has grounded light on I could probably just plug to same outlet this one is to see if actual grounded

Monitor has 3 prog power cord the TV is 2 prog




Sadly moving the monitor (Asus VS248) is not really an option I would have move my entire room which I not about to do. Computer is under desk said monitor is on, but turn the computer off does stop signal from droping so long as monitor is on, as I test that by connecting my ps5 to that and it happened there too

I do know that Moving the DP to DVI cable under desk can and does effect the signal, depending on where that cable is I might have spotty signal or no signal out all with the monitor on. but soon as it is off signal is fine.

The DP to DVI cable is shielded and the coxial cable is a shielded RG6 cable

I will see about moving the monitor 5+ feet way just to see if proximity to tv is issue. but that wont really solve my issue cause moving desk and there for computer and monitor isnt really option


worth try I see what happen when I get hand on some aluminum foil
So, the TV is Not Grounded ...
I'm interested to see what happens when you move the TV away from the rest ...
T
So, the TV is Not Grounded ...
I'm interested to see what happens when you move the TV away from the rest ...
TV is fix mounted to wall on metal brackets it can tilt and slide to side that is it it it 8 feet off ground and 55" tv it not getting moved . if it ground issues on TV how how can I fix that? I thought if surge protector is ground so are devices

It TCL 55S515 TV I have 2 of them in house both are 2 prog and most TCL tv I seen are 2 prog maybe there bigge sets are
Can you move the Antenna away from the monitor ?
Antenna is 8 feet away from tv I tried put 10 feet way didnt make difference

If I being honest after NHL Stanley Cup games I will probably stop caring and disconnect the OTA anyway cause I dont watch anything on anyway just my mom does and she attenna on here tv that really not much better it just dont have singal halve issue I have but it would be nice if I could fix,

probably the easy fix would be to get Tablo put antenna in attic like dad thinking of doing run coaxial to tablo and let feed tvs that way
Jimbo
TV is fix mounted to wall on metal brackets it can tilt and slide to side that is it it it 8 feet off ground and 55" tv it not getting moved . if it ground issues on TV how how can I fix that? I thought if surge protector is ground so are devices

It TCL 55S515 TV I have 2 of them in house both are 2 prog and most TCL tv I seen are 2 prog maybe there bigge sets are

Antenna is 8 feet away from tv I tried put 10 feet way didnt make difference

If I being honest after NHL Stanley Cup games I will probably stop caring and disconnect the OTA anyway cause I dont watch anything on anyway just my mom does and she attenna on here tv that really not much better it just dont have singal halve issue I have but it would be nice if I could fix,

probably the easy fix would be to get Tablo put antenna in attic like dad thinking of doing run coaxial to tablo and let feed tvs that way
Well, it's grounded up to the Surge Protector anyways ... but if not 3rd prong, it's not grounded ... I don't recall if my TV's have a ground, guess I never thought about it ...
Now ya got me curious, I got to check.

Well, thats interesting, I thought all TV's were grounded ... guess not, maybe they figure if the voltage gets that far, its not going to save the TV ... :(
navychop
Double insulated.
  • Like
Reactions: Foxbat and AZ.
T
Double insulated.
yes my tv is double insulated. could that be part of my problem?

I dont even get why my monitor and or the DP to DVI cable is causing this the cable is shield for this stuff yet moving that cable obviously effect the ota signal and simple act of that monitor be on cuts single in half, monitor on but in standby mode is fine, as far as i know computer gpu? is still out puting signal to monitor even when the monitor is standby mode it just dont wake up till the mouse or some input moves

aluminum foil over my monitor did stop the issue or even help in the lest
M
yes my tv is double insulated. could that be part of my problem?

I dont even get why my monitor and or the DP to DVI cable is causing this the cable is shield for this stuff yet moving that cable obviously effect the ota signal and simple act of that monitor be on cuts single in half, monitor on but in standby mode is fine, as far as i know computer gpu? is still out puting signal to monitor even when the monitor is standby mode it just dont wake up till the mouse or some input moves

aluminum foil over my monitor did stop the issue or even help in the lest

Something to try. Using an extension plug the TV into a completely different source of AC. Monitor may be feeding noise back into AC.
  • Like
Reactions: navychop and FTA4PA
nelson61
Lifetime Supporter
Last reply · posted in DISH Network Support Forum
EchoStar has filed with FCC for license and launch of the EchoStar 25 satellite at the nominal 110W slot.

------"At the nominal 110° W.L. orbital location, EchoStar is licensed to operate over 29 of the available 32 DBS channels (specifically channels 1-27, 29,and 31).3 Currently, EchoStar provides service over these channels from the 110° W.L. cluster utilizing the EchoStar 10, EchoStar 11 (in inclined orbit), and EchoStar 23 satellites; and from the 119° W.L. cluster utilizing the EchoStar 14 and EchoStar 15 satellites. EchoStar anticipates that EchoStar 25 will be ready for launch as early as the first quarter of 2026. EchoStar anticipates that EchoStar 25, a spot-beam satellite, will take over delivery of certain programming services from EchoStar 10 and 14. After launch and in-orbit testing ("IOT"),4EchoStar 25 will proceed directly to 110.0° ± 0.05° W.L. Once EchoStar 25 is placed into operation, EchoStar 10 will initially remain at 110.2° W.L. serving as an in-orbit spare and may ultimately be relocated subject to all appropriate Commission authorizations. EchoStar 14 will remain at the nominal 119° W.L. orbital location and serve as an in-orbit spare once EchoStar 25 begins service." -----
79 Replies · 7687 views
zippyfrog
I can tell the new satellite is active... When I go to the point dish menu, here in Chicago, 110 TP 27, which is a Spotbeam, for me with the old satellite was in the signal strength 50's-60's, is now just fluttering between 16-18.
D
When I go to the point dish menu, here in Chicago, 110 TP 27, which is a Spotbeam, for me with the old satellite was in the signal strength 50's-60's, is now just fluttering between 16-18.
Any chance you (or somebody else w/Chicago locals) could check & see where all the Chicago locals moved to, please...
  • Like
Reactions: charlesrshell
zippyfrog
Any chance you (or somebody else w/Chicago locals) could check & see where all the Chicago locals moved to, please...
That is a great question. I can't check at the moment but will check if no one else is in Chicago area can chime in on where they went.
  • Like
Reactions: charlesrshell
zippyfrog
Actually, I can't seem to add the locals back to my account to check right now - when I go to add it and I submit the changes, it shows that I have added 1802 local channels (the whole country) and nothing happens. Something must be wrong with their website. :)
R
Any chance you (or somebody else w/Chicago locals) could check & see where all the Chicago locals moved to, please...

Any chance you (or somebody else w/Chicago locals) could check & see where all the Chicago locals moved to, please...
I just happened to find out that I won White Sox tickets for tomorrow nights game June 10th. Yahoo! I just picked up my tickets around 8 P.M. local time and it is kind of late planning I know but I am leaving here in just a few and heading up to Peotone to stay the night tonight in a hotel and be there for tomorrow night as well. Its 9:21 P.M. Central Time now. I am hoping to beat the possible thunderstorms and fog early this morning up there and the weather there tomorrow as well. I oh so hope they play and no severe weather! Anyways, I just unhooked my Wally receiver and my DISH Playmaker and I am taking it with me. Peotone is in the Chicago Locals market and with me having a DISH Outdoors account I can change it when I get up there. I will have a check when I get there and I can post and let you know. I can put the antenna on top of the roof of the vehicle and run a 12 ft. coaxial cable running through the trunk into the vehicle. I have a DC to AC converter in the vehicle and can bring my Cloner Alliance ViewPRO to use as a the screen. I may even watch a little TV throughout the evening as well and maybe a little WGN as well. I miss WGN. I use to watch the Cubs, White Sox, and Bulls games on WGN and listen to the news and Tom Skilling a bunch. I hated it in December of 2014 when it became a standard cable network only. This will be only my 2nd time since they became a standard cable network and now defunct and rebranded as NewsNation that I actually get to see WGN again. The only other time was in 2016 up in Chicago as well and they were a standard cable network here then and not available locally. I now need to get going. I will let you know later.

RJ T.
From Illinois
  • Like
Reactions: charlesrshell
R
I just happened to find out that I won White Sox tickets for tomorrow nights game June 10th. Yahoo! I just picked up my tickets around 8 P.M. local time and it is kind of late planning I know but I am leaving here in just a few and heading up to Peotone to stay the night tonight in a hotel and be there for tomorrow night as well. Its 9:21 P.M. Central Time now. I am hoping to beat the possible thunderstorms and fog early this morning up there and the weather there tomorrow as well. I oh so hope they play and no severe weather! Anyways, I just unhooked my Wally receiver and my DISH Playmaker and I am taking it with me. Peotone is in the Chicago Locals market and with me having a DISH Outdoors account I can change it when I get up there. I will have a check when I get there and I can post and let you know. I can put the antenna on top of the roof of the vehicle and run a 12 ft. coaxial cable running through the trunk into the vehicle. I have a DC to AC converter in the vehicle and can bring my Cloner Alliance ViewPRO to use as a the screen. I may even watch a little TV throughout the evening as well and maybe a little WGN as well. I miss WGN. I use to watch the Cubs, White Sox, and Bulls games on WGN and listen to the news and Tom Skilling a bunch. I hated it in December of 2014 when it became a standard cable network only. This will be only my 2nd time since they became a standard cable network and now defunct and rebranded as NewsNation that I actually get to see WGN again. The only other time was in 2016 up in Chicago as well and they were a standard cable network here then and not available locally. I now need to get going. I will let you know later.

RJ T.
From Illinois
Update Wednesday June 10, 2026 @ 1:07 A.M. CDT.

Well I made it safely to Peotone, IL and got checked in. Sitting in the vehicle right now and everything is hooked up and ran and locals changed through the App.

I only have 2 words. "Very Interesting"

This is going to take awhile to post all of this and get all of this right so I am going to be looking up some info as I type.

Chicago has tons of channels! 18! To be exact all in HD.

So let's start.

002-00 WBBM (CBS) SAT: 110 SB: 12
Now playing: (Comics Unleashed With Byron Allen)

005-00 WMAQ (NBC) SAT: 110 SB: 12
Now playing: (NBC Nightly News With Tom Llamas)

007-00 WLS (ABC) SAT: 110 SB: 12
Now playing: (Live with Kelly and Mark)

009-00 WGN (CW) SAT: 110 SB: 12
Now playing: (The Goldbergs)

011-00 WTTW (PBS) SAT: 110 SB: 26
Now Playing: (Nature)

023-00 WWME (METV) SAT: 110 SB: 26
Now Playing: (Mannix)

026-00 WCIU (IND) SAT: 110 SB: 26
Shows The U - Now playing: (The Perfect Line)

Time change to 1:30 AM

032-00 WFLD (FOX) SAT: 110 SB: 12
Now Playing: (Sherri)

038-00 WCPX (ION) SAT: 110 SB: 26
Now Playing: (Chicago Fire)

044-00 WSNS (TELM) SAT: 110 SB: 26
Telemundo Channel speaking Spanish.
Now Playing: (Programa pagado)

048-00 WMEU (IND) SAT: 110 SB: 26
Now Playing: (Comedy Classics)

050-00 WPWR (IND) SAT: 110 SB: 26
Infomercial right now playing: (Ideal Prostrate+ Provides Safe)

056-00 WYIN (PBS). SAT: 110 SB: 26
Shows Lakeshore PBS - Now Playing: (Amanapour and Company)

059-00 WTVK (SHOP LC) SAT: 110 SB: 26
It is the Shop Liquidation Channel. All I get is a black background but was able to obtain satellite and spotbeam information - Shows playing in guide (which isn't) Spectacular Night Owl Jewelry Deals

060-00 WXFT (UNIMAS) SAT: 110 SB: 26
UNIMAS Channel speaking Spanish - Now Playing: (El Chavo)

061-00 WPVN (IND) SAT: 110 SB: 26
Shows WiN TV on the screen with Korean people and Korean Language - Now Playing: (WIN BNC)

062-00 WJXS (IND) SAT: 110 SB: 12
Shows wjys The Way - Now Playing; (Paid Proograming) but a church service is showing instead.


And finally…

And a time change to 2:00 AM

066-00 WGBO (UNIV) SAT: 110 SB: 26
Univision Channel speaking Spanish - Now Playing: (Programa pagado)

Now done!

Wow! About an hour's worth!

So it appears they changed as well to the 110 Satellite and using 2 Spotbeams 12 & 26.

Got to head up to my room and get some sleep. I will be here until late afternoon tomorrow before I head up to the game and will be back here after the game tommorow night and head back home Thursday morning.

Take care everyone and have a good night and a good Wednesday and Thursday. Probably won't be back on until Thursday.

RJ T.
From Illinois
zippyfrog
This is really interesting. Thanks for posting the Chicago locals - I still can't add them to my account for some reason.

But what I find even more interesting is that you are reporting that some of the Chicago locals are on 110, TP 12. However, right now some of the national sports channels for the out of market sports channels are on 110, TP 12 as well. MLB Network Alternate, for example, is currently on 110, TP 12. And to my knowledge, the same transponder cannot be both a national ConUS transponder as well as a local spotbeam. I wonder if having both satellites active at the same time is causing some coding issue or something like that - for my receiver, it is as if it is checking one satellite, times out, then checks the second satellite for the signal strength.
  • Like
Reactions: charlesrshell
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in The Chit Chat Club
Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne


Get it?


An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
67090 Replies · 2661929 views
  • Like
Reactions: c-spand
long_time_DNC
Standing On Higher Ground - Alan Parsons Project
sdfntx
Standing in the Shadows of Love - The Four Tops
long_time_DNC
Chasing Shadows - Kansas
H
SHADOWS Of The Night-Pat Benatar
  • Love
Reactions: ClarkGable
ClarkGable
Night Moves - Bob Seger & The Silver Bullet Band
  • Like
Reactions: RaiderPower
TWiT Tech Podcast Network
· posted in TWiT Tech Podcast Network
0 Replies · 14 views