Social Feed

Dee_Ann
Last reply · posted in DISH Network Support Forum
For the past few days I was getting a lot of HD channel signal loss where it would fall back to an SD channel. Ugh!

So the other night I walked out and put my hand on the dish and found that it was loose, we've been in a drought and the yard is very dried up and cracked badly.
As the dirt dries out the pole gets loose. So I put a garden house out there to wet the ground and it tightened back up. But I still had no signal on 129.
So I went into the tuner setup and told it to disconnect the EHD. It told me it was safe to remove the disk which I did. BTW, it's a 2TB disk that has been working fine for over a year and a half and was working just fine moments before I told it to disconnect.

So I take the tuner out into the yard and realign the dish and once again it sees all three dishes (I have three separate BIG dishes) and was getting all the channels as it should.

I bring the tuner back into the house and plug everything in and power up. The EHD disk light is blinking rapidly and the tuner does not see it. Yet?

Is it going through a long disk check before it will allow it to reattach? Every single morning it goes through like 4-5 disk checks, acquiring the signals, downloading updates and the guide that all in all from start to finish takes just under 2 hours, I guess it's because the disk has a LOT of stuff on it and that it's 2tb.

Please tell me that it's just going through a painfully slow disk check before it reattaches itself???????? :sick:
The tuner does not recognize it as of now and I can't do any pause, rewind, recording stuff. And the pathetic little one day guide is very annoying..

I do not believe the disk is bad, it was working perfectly earlier. I can't afford to replace the disk and I really will be sick to my stomach if I've lost a year and a half of recordings!

Also, is there anyway to back up your EHD recordings?

Thanks..
18 Replies · 3150 views
dwarren2
Did you try what I suggested? When I had a 211, if I disconnected the ehd I had to first restart the 211 then add the ehd. It would then reboot. It had to do that so that it can use the ehd as a dvr.
Teehar
Hell hath no fury as a dish woman scorned!

Seriously,I hope the disk isn't bad Dee,but I don't have any other ideas as to what it could be.I don't know if windows would see the drive under disk management,but you could try that.I'm thinking that linux would see it if it isn't toast.
Dee_Ann
Did you try what I suggested? When I had a 211, if I disconnected the ehd I had to first restart the 211 then add the ehd. It would then reboot. It had to do that so that it can use the ehd as a dvr.


I tried multiple times.
Dee_Ann
Hell hath no fury as a dish woman scorned!

Seriously,I hope the disk isn't bad Dee,but I don't have any other ideas as to what it could be.I don't know if windows would see the drive under disk management,but you could try that.I'm thinking that linux would see it if it isn't toast.


The disk was in a docking station. I plugged it into a little laptop I have that runs Mint Linux. It does not recognize the disk. One time when I first got the tuner I plugged the same disk & docking station into the same laptop out of curiosity and it did recognize it. I was able to browse the disk but it was all apparently encrypted by Dish so you can't copy recordings from it. How nice of them.


I've given up and written it off as a total loss. For now I've set the dead disk in a drawer. I'm shopping for the things I need to prevent this ever happening again.

I found a 160gb disk for $29 on Amazon. I already have the docking station. Three of them actually.

I'm going to buy the Hauppage PVR box and the OSX software from Amazon for about $150.

With a small disk it won't allow me to record a year of stuff. It will allow me to record for a few weeks before I have to dump it into the PVR connected to my Mac.
I'll keep the little disk cleaned out so it won't do a two hour disk check every morning. This will not happen again..
KAB
KAB
Nighty, Night, Dee!
KAB
KAB
The disk was in a docking station. .
On this, I will give you benefit of a doubt. If the docking station being a BlackX or the like, you have to JAM the HD into them. Easy to think it's seated, but very well likely, NOT. Will never buy another one.
dwarren2
Rather than a docking station, try a powered external hard drive, if you have one. That's what I've always used as an ehd on my 722, 211 and now HWS;s.
Former member 209992
Last reply · posted in SatelliteGuys Support Center
For some reason, the satelliteguys.us site is loading a lot slower than usual on both Chrome on my Asus laptop and Safari on my iPhone.
I'm also seeing longer appearances of the blue bar at the top and the "3 blue bars" loading symbol.
Is anyone else also having the same problem? Thanks in advance.
534 Replies · 18180 views
  • Like
Reactions: charlesrshell
Scott Greczkowski
Remember folks... just like DNS... its always Foxbat. :D
Foxbat
Remember folks... just like DNS... its always Foxbat. :D
WTF… …What the Foxbat!😱
S
WTF… …What the Foxbat!😱
wow what a kick in the balls!!! the wife blames you when things don't work now scott's blaming you :biggrin
  • Like
Reactions: charlesrshell
Foxbat
wow what a kick in the balls!!! the wife blames you when things don't work now scott's blaming you :biggrin
I know. Here's what Scott has in store for me if I get out of line:
IMG_1990.webp
IMG_1989.webp
comfortably_numb
I know. Here's what Scott has in store for me if I get out of line:

Not likely since that place closed down.
Foxbat
Not likely since that place closed down.
You're no fun.😑
comfortably_numb
Site was down for a good 20+ minutes just now.
Foxbat
Site was down for a good 20+ minutes just now.
Huh, that's interesting, it was like I had the site all to myself…🤣

JK, JK! Scott will explain when he gets back home and can get online.
  • Like
Reactions: charlesrshell
T
Was down for me also
  • Like
Reactions: charlesrshell
TRG
TRG
Site was down for a good 20+ minutes just now.
Ditto
  • Like
Reactions: charlesrshell
Peter Parker
Supporting Founder Lifetime Supporter
Last reply · posted in DISH Network Support Forum
No idea what improvements might be involved.
10 Replies · 520 views
  • Like
Reactions: LQQK and reubenray
cpdretired
Two bugs out and three new bugs in.🐞
Almighty1
Updated to H713 on a Hopper 3 from H712 with Hopper Plus a few hours earlier.

It brought a old problem back:

One of the problems I am seeing is that the Available Joey Software section no longer is showing the Android TV versions even after a manual software reset twice and the nightly reboot. Until it does, nether Technician Android TV download and Hopper Plus is able to check, download and update the Android TV software.

This was a major problem with H703.

H710 removed that dependency but it's broken again.

Rick Durham and brittanygarden
  • Like
Reactions: charlesrshell
dishstaller
Two bugs out and three new bugs in.🐞
Yep. Just got a call from a customer who said her DVR buttons stopped working. Told her about the new software and had her reboot her H3, problem solved.
  • Like
Reactions: charlesrshell
S
Updated to H713 on a Hopper 3 from H712 with Hopper Plus a few hours earlier.

It brought a old problem back:

One of the problems I am seeing is that the Available Joey Software section no longer is showing the Android TV versions even after a manual software reset twice and the nightly reboot. Until it does, nether Technician Android TV download and Hopper Plus is able to check, download and update the Android TV software.

This was a major problem with H703.

H710 removed that dependency but it's broken again.

Rick Durham and brittanygarden
i can still see my joey software version with H713.. i am starting to think it's time to get rid of the hopper plus. i just have 2 joey 4's and the hopper 3 with no issues. it seem like the people that have the hopper plus have issues!!!
  • Like
Reactions: charlesrshell
Almighty1
i can still see my joey software version with H713.. i am starting to think it's time to get rid of the hopper plus. i just have 2 joey 4's and the hopper 3 with no issues. it seem like the people that have the hopper plus have issues!!!
Are you talking about the Available Joey Software section which goes something like this:
Available Joey W153 W209 J613 J713 J813 K113 J913
Software
in H713 in diagnostics which is directly below the "Switch" section which is what I am referring to that should have a number starting with P which is needed for the
Hopper Plus, Joey 4 and Wireless Joey 4
or the top area where it shows what the current version of the software is for the Hopper 3?

Seeing what your Joey 4/Wireless Joey 4 software version just tells you what is the current software version already installed, until the P version(s) shows up in "Available Joey Software" section which is different for the Hopper Plus, Joey 4, Wireless Joey 4 and it will only list one for the device(s) that exist in one's own configuration which lists what's the latest available, those devices will not be able to check or update their software as it will say "Failed: No Tgt" while "Download ATV Files" in TECHNICIAN SETTINGS under tools will respond with:
"Download ATV Files 3000
This device is not currently targeted for
Android software"
as both are dependent on the P version being listed in the "Available Joey Software" section. It usually takes a few minutes before it shows up. I know with H710-H712, it was not shown and the Download ATV Files worked except since H710, even if you selected everything shown which for me would be the Hopper Plus, Joey 4 and Wireless Joey 4 versions, the first download will as a end result only download the Hopper Plus's versions even though it shows all three as downloaded based on what Available Joey Software shows which is always two P numbers P153 and P15317. After the first successful download, the next download will actually download all three and Available Joey Software will reflect that. In H708 (H709 was skipped as no one mentioned it on the forums) and earlier, it always downloaded everything selected and would show 6 P versions in the Available Joey Software area. The Available Joey Software section is how I tell if there is a newer software available for the Hopper Plus and when I see that, I do the Download ATV files first which is where I get my information to post in my other thread, "Latest available software version for Android TV devices - Hopper Plus, Joey 4, Wireless Joey 4". The Download ATV files does not do any install or update the Hopper Plus as I still need to manually hit Menu, Settings, Device Preferences, About, Software Update to update the software.

So with any new Hopper 3 software update, the first things I will check is the Notifications in Settings to see if any of the settings were reset. For the "Remote Control Mode Reminder" setting, I would try it with off, exit notifications then hit TV on the side of the remote to make sure it does not show the reminder before going to notifications andputting it back to on, exit to see if it works correctly before going back to notifications for the other settings. Then I would look at Available Joey Software and regardless if the 2 P versions, one appears to be the 3 digit major version number and the other is the full 5 digit number which is the 3 digit major version number with 2 more digits, exists or not. Attempt to do the Download ATV Software for all 3 Android TV devices Hopper Plus, Joey 4 and Wireless Joey 4 until all of them is downloaded and shown in Available Joey Software which should be a total of 6 things added. If Download ATV Software has the no target like since H713, I will wait until I see a P version before I do it.

For reference, it's in the following threads:
  • Like
Reactions: charlesrshell
bookworm370
Yep. Just got a call from a customer who said her DVR buttons stopped working. Told her about the new software and had her reboot her H3, problem solved.
Reboot just fixes it for a short time and then it's back to messed up

Try going exclusively to an IR remote and you will see the pain
Almighty1
Updated to H713 on a Hopper 3 from H712 with Hopper Plus a few hours earlier.

It brought a old problem back:

One of the problems I am seeing is that the Available Joey Software section no longer is showing the Android TV versions even after a manual software reset twice and the nightly reboot. Until it does, nether Technician Android TV download and Hopper Plus is able to check, download and update the Android TV software.

This was a major problem with H703.

H710 removed that dependency but it's broken again.

Rick Durham and brittanygarden

Within the last few hours as I did check earlier today when it was still missing, the Available Joey Software line now has added "P154 P15403" which is for the Hopper Plus that I have but my Hopper Plus software is still on P15317, I will do a Download Android TV (ATV) Software for the Hopper Plus, Joey 4 and Wireless Joey which are all Android TV devices and then manually do a check update on the Hopper Plus to update the software shortly.
  • Like
Reactions: charlesrshell
BatStang2000
This happened to me. I was outside mowing and my wife came out and said that our nieces and nephews were going to be on the Noon News. She had it on in the bedroom on our Joey3. Since they weren't on yet, I decided to turn it on in the Living Room on our Hopper3. When I selected the channel (through Dish, not OTA) the Joey3 turned itself off. When I went back to the bedroom to turn it back on, the Hopper3 did a reboot. Luckily it all finished before their story came on, but I just found it strange.
  • Like
Reactions: charlesrshell
Van
Van
Last reply · posted in What's Cooking?
Who says dinner or lunch has to be the only good meals of the day?

Honey butter grits with scrambled eggs and grilled boneless pork ribs on flakey biscuits washed down with cranberry juice.
6630 Replies · 379374 views
TRG
TRG
Bacon, eggs, hash browns and toast. Coffee.
  • Like
Reactions: Mr Tony and dfergie
TRG
TRG
Wound up at the Waffle House this morning. Got the two egg breakfast with coffee.

1622.webp
  • Like
Reactions: dfergie and Mr Tony
dfergie
Speaking of waffles, I'm going to put my mini waffle iron on stove so I'll remember to make waffles in the morning... Had some last week, been awhile.
dfergie
Dos cackleberrys over easy on top of 2 corned beef hash patties fried in skillet... Chocolate milk.
  • Like
  • Love
Reactions: TRG and Bobby
TRG
TRG
Cold morning today, only 32 degrees. Fired up the oven and made cinnamon rolls (from a tube) and a pot of coffee.
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in The Chit Chat Club
Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne


Get it?


An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
68511 Replies · 2671604 views
  • Like
Reactions: c-spand
ClarkGable
Five O'Clock World - The Vogues
  • Like
Reactions: sdfntx
FTA4PA
Six O'Clock News - John Prine
  • Like
Reactions: sdfntx
Bobby
It's Five O'Clock Somewhere - Alan Jackson
harshness
Somewhere - Barbra Streisand
sdfntx
Somewhere in Time - John Barry
meStevo
Lifetime Supporter
Last reply · posted in The Chit Chat Club
Continuing the Kilauea thread in the Pub here. Perhaps the Iceland one too next time there's remarkable activity.

Currently there is precursory lava flowing into the crater, leading to the next episode that'll probably start within the next day.

You can see the pace of inflation / deflation here. It serves as the primary predictor for when the expect the eruptions, which coincide w/ inflation turning into significant deflation and last for several hours on average with significant fountaining.



View: https://youtu.be/Uecu2seh4b4


Wife and I like the AfarTV feeds, for the discussion along w/ them, though they're otherwise just mirrors of the official USGS feeds.


View: https://youtu.be/iws3rh5vLAQ
119 Replies · 3234 views
  • Like
Reactions: osu1991
Foxbat
​
  • Like
Reactions: RaiderPower
Foxbat
​
Foxbat
Oooo, quite the show now. All three vents have doming and overflows. The cone that built up around the North vent lost its upper quarter at 02:50 Oct 17 and is now spewing lava at a healthy rate. Don't know if I would say it's a fountain, but it's close.


IMG_1534.webp

edit: The USGS has called the official start of Episode 55 as starting at 03:19 HST Oct 17, 2026:

Alert Level: WATCH, Color Code: ORANGE 2026-10-17 13:43:56 UTC
HVO/USGS Volcanic Activity Notice

Volcano: Kilauea (VNUM #332010)

Current Volcano Alert Level: WATCH
Current Aviation Color Code: ORANGE

Issued: Saturday, October 17, 2026, 3:43 AM HST
Source: Hawaiian Volcano Observatory
Notice Number: 2026/H488
Location: N 19 deg 25 min W 155 deg 17 min
Elevation: 4091 ft (1247 m)
Area: Hawaii

Summary: Episode 55 of the ongoing Halemaʻumaʻu eruption began at 3:19 AM HST on October 17, 2026.

Volcanic Activity:
Episode 55 of lava fountaining in Halemaʻumaʻu began at the summit of Kīlauea began at 3:19 AM HST on October 17, 2026.

Fountain heights are relatively low at about 100-150 feet (30-45 m), and it is not clear whether this episode will evolve to the same heights as previous episodes. Continuous overflows from the vents began yesterday, October 16, just before 6 a.m. HST and transitioned into episode 55 fountains at 3:19 a.m. HST this morning. The current forecast is for winds are blowing from the north-northeast direction, which suggests that volcanic gas emissions and volcanic material may be distributed to the south-southwest direction from Halemaʻumaʻu.
  • All eruptive vents and lava flows are confined to Halemaʻumaʻu crater within Hawaiʻi Volcanoes National Park. Tephra fall from volcanic ash clouds is greatest within 3 miles (5 km) of the vents, lighter ash and Pele's Hair may stay suspended for large distances from the vents.
Foxbat
Kīlauea seems to be returning to the "normal" eruption script, impressive fountaining from the North Vent. For once, the V2 Cam has the best overall shot:
IMG_1535.webp
The lava flows have covered a good portion of the Halemaʻumaʻu crater floor.
BlackHitachi
Supporting Founder
Last reply · posted in Movie Talk
Since the Reds have there thread we should too!

Last watched Nine inch Nails
Next 3:10 to Yuma
5390 Replies · 510355 views
osu1991

View: https://youtu.be/9j3vxhzM8MY?is=Rs1cY1FQAiRWi87i


Come September (1961)
Rock Hudson and Gina Lollobrigida with Sandra Dee and Bobby Darin
  • Like
Reactions: dfergie
Y
1791758462355.webp


Simple, charming. Entire premise is quite silly but Cary Grant carries it across the line in good fashion.
T
Last: The Social Reckoning. Spoiler alert, they make Zuck look like a...
Foxbat
Since it was already "paid" for, I spent the two hours of my time watching the John Cena action movie on Apple TV, "Matchbox The Movie" even though the reviews were brutal. It was better than I expected, so I didn't feel like I had wasted an afternoon watching it. But it felt like another "Reacher"/"Neghley"/"Mission: Impossible"/"Fast & Furious" crash and blow stuff up with lots of automatic gunfire mixed in movie featuring covert CIA operatives.

I don't think we'll get a follow-up movie from this. I expect Mattel will have other toy lines to exploit.
  • Like
Reactions: osu1991
dfergie
Staff member HERE TO HELP YOU!
Last reply · posted in What's Cooking?
Anyone making their own breakfast sausage? I've recently been trying different recipes, found some I like, some I've modified...
38 Replies · 3565 views
  • Like
Reactions: spongella
navychop
Bob Evans Sage.
R
Bob Evans Sage.
I will look, but I don't think I have seen it. Owen's breakfast sausage use to be favorite, but I can't find it anymore. Jimmy Dean's country mild is OK also when I can find it.
  • Like
Reactions: navychop
dfergie
Swaggerty's isn't too bad, sausage prices are lower per lb than making my own from pork butts right now so I've been buying JC Potter or Owen lately.
(Swaggerty's at Sam's is pre cut, I usually partially freeze the rolls and cut with my slicer and vacuum seal on parchment paper)
  • Like
Reactions: navychop
S
I will look, but I don't think I have seen it. Owen's breakfast sausage use to be favorite, but I can't find it anymore. Jimmy Dean's country mild is OK also when I can find it.
amazon maybe :what
S
I will look, but I don't think I have seen it. Owen's breakfast sausage use to be favorite, but I can't find it anymore. Jimmy Dean's country mild is OK also when I can find it.
owens on amazon is 54.99 for a 4 pk 16 oz a sausage. i feel that's kind of steep!!!
S
Swaggerty's isn't too bad, sausage prices are lower per lb than making my own from pork butts right now so I've been buying JC Potter or Owen lately.
(Swaggerty's at Sam's is pre cut, I usually partially freeze the rolls and cut with my slicer and vacuum seal on parchment paper)
id'e rather make my own vs store bought.
  • Like
Reactions: dfergie
R
owens on amazon is 54.99 for a 4 pk 16 oz a sausage. i feel that's kind of steep!!!
Especially when I can get a two pound roll of Jimmy Dean from Sam's Club for $7.38.
dfergie
They run Owens at $3.99 for lb and $7.99 a couple times a month at some grocery stores here, I actually was wrong, just checked a pork sirloin roast it was $1.99 a lb. (cooked it yesterday so pack was in trash)
  • Like
Reactions: reubenray