Hi MikeD-C05. Your topic about the two arcs caught my interest. I'm down here in Pharr, Texas trying to set up a Dish Network 1000.2 HD Eastern Arc antenna for the 61.5 and 72.7 satellites. I was able to find 61.5 without a problem, but I'm having trouble locating 72.7. Looking at the recommended settings from my Dish Vip211z receiver, it shows nothing for a skew. I find this hard to believe. I don't have a current zip code table for 1000.2 EA settings, but I have one for 1000.4 which shows the skew at 49 for my 78577 zip code area. However, if I try setting the skew around there, I lose 61.5 at the recommended AZ and EL settings. I noticed in your post that you did a setup for your parents who are also in Texas, and you mentioned that you changed the skew. Now I'm wondering where you got the new skew settings from, because I've searched the net for a 1000.2 EA table and found nothing. Any recommendations? Thanks in advance!
When I bought my new eastern arc lnb , I got it from
www.dishdepot.com. ( He charges no tax on any item sold and free shipping unless you are asking for expedited service. I've done business with Mark since 03 and he has always given me great service and even trade ins on OWNED receivers are welcomed towards credit for new receivers ) He provided with the lnb, the installation book for both arcs and the 1000.2 dish. It provides the skew ,elevation and azimuth directions for both western arc and eastern arcs.
For your zip code in Pharr ,Texas I read online that you have one zipcode for your area: 78577. The eastern arc lnb directions for your area are :Elevation of the dish is 46 /Skew of the dish is 46/Azimuth is 123.
If you are pointed towards western arc sats 110/119/129 ,like I was at my parents house, you will have to take the sat dish pan off and re-adjust the skew so it is pointed to 46 skew and then put the pan back on and bolt it all down. The directions say that if you need to use the additional bolts along the skew plate, if use skews that are either greater than 110 or less than 70. So basically your sat dish need 4 bolts to keep the skew plate locked down so it doesn't shake in the wind. Also if you are changing arcs you need to clear out your switch matrix,by running a check switch without the sat coaxes connected to your receiver and save the results ,even though they will show nothing in your matrix. Then put the coaxes back on your receiver on so you can use the meter for signal strength when you peak it.
Now once you get the dish pan back on and pointed in the general direction of the eastern sats - 123 azimuth using a compass, and your skew plate locked in place on 46, elevation also on 46 , you can take a sat meter and a coax ( cheap one I got at dishdepot) and put it on the first port of the lnb and peak on 72.7 sat transponder 13 . Now , the first time I did this I swiveled the dish to the left and the meter went off 10 strength ,but when I went in the house, I found I was on the 77 sat. So I swiveled back a little to the right and I got 72.7 to come in. So don't be surprised if you have the same issue. Both sats are very near each other. If you get 77 sat to show up , you are only a slight swivel to the right to get 72.7.
Once you are peaked on 72.7 , that is all you have to do , 61.5 is already there,assuming you use the right skew and elevation. I used my son on his cell phone to tell me if I got a strong enough signal. Because you can hear the sat meter go off ,but you can't know what strength you are getting , just 1 - 10 on the meter. I could only get around 36, no matter if I changed the elevation -which I didn't need to do. After I got it peaked on transponder 13 and locked my dish in place, and ran the coax back through like it is supposed to do and reran my check switch. I got around 62 on that same transponder. In fact I got like between 55 - 68 on all the transponders. Remember that on eastern arc anything 50 or higher is a great signal so not to have excessive rain fade issues. So make sure that you get your switch check run and let your receiver download the guide and you should be in business.
One other tip if you want to see the elevation skew and azimuth angles for yourself is to go to DISH's website , then choose support heading then installation sub heading and then pick the 1000.2 sat dish and there you will find both western and eastern arc look angles etc.
Good luck .
