Social Feed

L
Last reply · posted in FTA Receiver / Equipment Support
I have added dual output lnb's over time. Now I would like to add a third and maybe fourth receiver to the mix. Currently I am only using 2 receivers(Amiko HD's). I have drawn up a diagram of what I think I need to do. Can I run the coax from the ASC 1 output to the KU motor input and then to output 1 on the 4 x 4 switch as in my drawing? Is there a better way of doing this?

I currently split the coax right before the receiver with a diseqc 1x4 and then port 1 to the ASC 1 and port 2 goes to the Ku dish. This works good and fortunately I had a second coax all ready run plus the switch gets to stay inside. Now I would like to use this second coax to feed another receiver.

4x4  (2).jpg
Looking forward to your help before I start making changes
15 Replies · 1544 views
L
Thank guys! I was unaware diseqc 1.2 and USALS could interfere with each other. So where to start?
Brian could you give me a step by step to get up and running? I assume the first step would be to write down the count numbers of my current sat positions and put the dish on my position one.
The KU motor is on another box currently . What is step 2?
If it's easier I can call your shop. Steps in print would be more fool proof for me. I appreciate any and all help you can give me.

My receiver is a Amiko HD RE and KU motor is a Digipower SG 2100.

There is no great hurry so let me know when ever it's convenient. Thank you in advance.

Not sure how to do a reset on the SG 2100. It's been years.
EDIT: I don't believe it. I found the manual for the SG 2100. Now I know how to reset it
EDIT: I was using USALS for the KU but then it was set up before the ASC 1 came along.
L
So I've had a bit to think this over.
Titanium - Brian , do I start from scratch?
Is a Receiver reset needed?
If I have this right, reset ASC 1?
With ku motor out of the loop reprogram c satellite positions( Diseqc 1.2 ) to ASC 1
When done add KU motor back into the loop( with motor at "0". Do I do a reset?)
Will this now work wired as in my original drawing?

Thanks for your assistance

Lee
Titanium
Have no clue if a SG2100 has factory preprogrammed DiSEqC 1.2 positions. In my experience preprogrammed DiSEqC 1.2 motor settings are referenced to 0 and have no movement unless programmed. Maybe the SG3100 manual would indicate if any motor positions are repopulated. If so, A33 makes a good suggestion to program the C-band DiSEqC 1.2 positions in the ASC1 50-99.

I would start by performing a factory reset on the SG2100 then bypass the SG2100 (no loop-through).

Program the STB and ASC1 for the C-band satellites using DiSEqC 1.2 motor type (if necessary - see above comments, use positions 50-99).

Put the SG2100 back inline and activate USALS in the STB for KU-band satellites.

That is all.
  • Like
Reactions: Lee60 and a33
L
Thank you Titanium and a33 for your help. I'll report back with my results
L
Just finished up. I did as advised except my Amiko only has 60 total Diseqc 1.2 positions available. So I started at 45 and ended at 59. I then did a reset on the KU motor and wired back in the loop. So now I have C(asc1) and KU controlled on one receiver.. No conflicts that I can tell.

Titanium and a33 I can't thank you enough.
  • Like
Reactions: Titanium and a33
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in The Chit Chat Club
Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne


Get it?


An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
68526 Replies · 2672549 views
  • Like
Reactions: c-spand
harshness
Delta Dawn - Tanya Tucker
dishstaller
Can't You See - Marshall Tucker Band
sdfntx
See You in September - The Happenings
long_time_Dish
You Look Like You Love Me - Ella Langley
  • Like
Reactions: dishstaller
dishstaller
See Me Feel Me - The Who
Peter Parker
Supporting Founder Lifetime Supporter
Last reply · posted in DISH Network Support Forum
No idea what improvements might be involved.
19 Replies · 785 views
  • Like
Reactions: LQQK and reubenray
bookworm370
Has anyone noticed an FF stutter with 713? I used to be able to hit FF a few times and skip smoothly. After 713 (maybe 712), when I skip forward, there is a definite stutter for as many times as I have pressed FF.

Can anyone check on this and report back? Recorded programs and then press skip forward a few times to see if it's smooth? Normally, it just jumps to the right place after the skips.
  • Like
Reactions: charlesrshell
N
I'm getting fabulous picture on Ch. 148 4k, but zero audio with H713. This is with a recorded show (Notre Dame game). Anyone else have this? Audio is fine on every other channel.
  • Like
Reactions: charlesrshell
R
Has anyone noticed an FF stutter with 713? I used to be able to hit FF a few times and skip smoothly. After 713 (maybe 712), when I skip forward, there is a definite stutter for as many times as I have pressed FF.

Can anyone check on this and report back? Recorded programs and then press skip forward a few times to see if it's smooth? Normally, it just jumps to the right place after the skips.
My wife mentioned that her remote is acting strange this morning. She hit FF and it went to 15x FF.
  • Like
Reactions: charlesrshell
Bobby
I'm getting fabulous picture on Ch. 148 4k, but zero audio with H713. This is with a recorded show (Notre Dame game). Anyone else have this? Audio is fine on every other channel.
This has been an ongoing issue. A fix is coming, probably in the next software version.
Foxbat
Wife bought me a t-shirt that has "have you tried turning it off and on again?"
Here's the one I need:
1792365258110.webp
dishstaller
Here's the one I need:
Just ordered one....that's great.
  • Like
Reactions: charlesrshell
dfergie
Staff member HERE TO HELP YOU!
Last reply · posted in The Chit Chat Club
Stumbled across this ... http://www.gaspricewatch.com/USGas_ZipSearch.asp
I found no local prices, although it did show stations at my location...
Added these to this post...
USA National Gas Temperature Map
State By State Gasoline Taxes
Gas Buddy

Ethanol Free Stations

5552 Replies · 460595 views
Bobby
Regular$5.999​
Premium$6.399​
Diesel$7.999​
at Costco, Rohnert Park.​
  • Like
Reactions: harshness
harshness
I wonder if California is getting into the Winter formula.
dishstaller
Regular$5.999​
Premium$6.399​
Odd that out there, Prem is only 40 cents higher. Here it's a full dollar more.

Last night it was about $4.17 gas, $6,19 diesel.
harshness
Odd that out there, Prem is only 40 cents higher. Here it's a full dollar more.
On the West Coast, a 40-cent differential is common. It used to be 30 cents before the prices rose above $3.

A "full dollar more" sounds like it may be boat gas (non-alcoholic), which is a whole different discussion.
  • Like
Reactions: Foxbat
Foxbat
Here in Indiana, the difference between Regular and Premium is usually a dollar, but some charge even more:
1792374072446.webp
  • Like
Reactions: dishstaller
dishstaller
A "full dollar more" sounds like it may be boat gas (non-alcoholic),
Both non-ethanol and prem run about the same....buck more. When we were up in TN it was a buck more up there as well.
jokeworm
Last reply · posted in What's Cooking?
Ok, I'm bored .... actually - to be more precise - I'm bored of eating the same rotation of 9 or 10 meals that are currently my "go-to" meals. My wife works the long hours - I work from home as and when i feel like it ... which means i generally do most of the cooking ... and so by default - i also make out the shopping list ...

We cook at home 5 or even 6 nights a week - but we always seem to fall back on the same old tried and tested "quick and easy but tastes ok" meals. Week in week out.

Pot Roast - mash and Peas.
Spaghetti
Chicken Pasta in cheese sauce.
Curry & rice
(these are some of mine)

Now it's not that I'm not adventurous in the kitchen ... I'll try anything once or twice ... but we all do it. Unless your name is Martha Stewart or Rachel Ray .. we all eventually fall back on our 8-10 favorite "meals"

So i thought - if we shared some of our own go-to meals with each other ... we might be able to add a few "new" ones to our own arsenal of meals.

So again - I ask you ...

What's for dinner tonight ?

Please give me something new to add to my rotation ... its our weekly shop tomorrow - so i want to pull together a few idea's and try and eat a meal each day next week that I've never had before .. or at least something that is not on my current "go-to" meal plan.

What meal do you always seem to fall back on in your house ? Maybe its something that I've never tried or not had in a while. I need inspiration !! I've got a blank shopping list in front of me - and nothing sounds good .. HELP !
4332 Replies · 331144 views
TRG
TRG
Beef and vegetable stew with buttermilk biscuits. Water.
It seemed appropriate on an unusually cold and wet evening in New Mexico.
  • Like
Reactions: dfergie
Bobby
Chili Cheesebugers, Tater Tots.
  • Like
Reactions: dfergie and TRG
TRG
TRG
I made shrimp parmesan with spaghetti and a salad.
  • Like
Reactions: dfergie
S
venison lasagna
  • Love
Reactions: Bobby
dishstaller
Smoked some salmon on the grill while enjoying some Blue Moon beer. Kinda cool tonight so I fired up the heaters. Here in FL, we fire up heaters once the temps get below 60 :cool As for the salmon, I seared them first, then flipped them off to the side not over the coals and brushed on some lemon pepper marinade followed by some salmon seasoning. Threw some hickory chips on the coals and then closed the vents to about 10% airflow. Yum.
  • Like
Reactions: Bobby
osu1991
Pub Member / Supporter
Last reply · posted in The Chit Chat Club

The number-one US state for EV growth, according to the June 22 Yardi report?
Oklahoma.


:eek


It has no ZEV mandates and "minimal" incentives, Yardi says, but also has cheap electricity, high multi-car household rates (so, for example, a non-Lightning Ford F-150 pulls their trailers), and a consumer base willing to switch.
112 Replies · 900 views
navychop
Servant's problem.
  • Like
Reactions: Bobby
meStevo

Never realized that Tesla is losing to BYD at manufacturing too, which IMO is Tesla's biggest accomplishment and area of innovation. Nice writeup about the state of play and how we got here though. I have no faith that we're moving any productive direction though sadly, most changes and efforts feel reactionary rather than rooted in making use of the time being bought by tariffs, with few exceptions.

So: how are the cars so cheap, and what is being cut to get there? The best public accounting comes from the Rhodium Group, which compared BYD, Geely, and Leapmotor against Tesla's Chinese operation, a fair comparison because it removes labor costs and shipping from the equation entirely. Their estimate is that BYD builds a car for about $4,700 less than Tesla builds a Model 3 in Shanghai, roughly 15 percent of the Model 3's price. The breakdown is the interesting part. Direct government grants account for about $292 per vehicle, which is 5 percent of the gap. The biggest single factor is vertical integration: BYD makes about 80 percent of its top-tier components in-house, against 37 percent for Tesla, and that eliminates roughly $2,369 per vehicle in supplier markups. Lower overhead, meaning cheaper engineering talent and administrative cost spread across enormous volume, accounts for another $1,719. And BYD pays its suppliers on 155-day terms, against Tesla's 60, which is worth about $214 per car in float. When people say the Chinese advantage is subsidies, the per-vehicle number says otherwise. When people say it is slave wages, the Tesla Shanghai comparison says otherwise too. The advantage is mostly that BYD decided, twenty years ago, to make its own batteries, its own motors, its own power electronics, and its own semiconductors, and Western automakers decided the opposite.​
harshness
The EV company to watch out for is SAIC. They seem likely to take over Government Motors at some point.

GM originally struck a JV deal with SAIC to gain access to China. Now SAIC has taken China back with the substantial library of technology GM shared and they're looking to export to Mexico, South America, the Middle East, and Asia-Pacific.
osu1991
  • Like
Reactions: Foxbat and AZ.
Ham Radio 2.0
· posted in Ham Radio 2.0
0 Replies · 11 views
Ramy
Supporting Founder
Last reply · posted in The Sports Section
Really excited for this season with Kentucky having a new coach and some really exciting recruits. Probably won't last long, but here's hoping this season is great.
148 Replies · 1734 views
  • Haha
Reactions: Mike0616
Foxbat
They ought to have fun with this… :devilish
osu1991
They ought to have fun with this… :devilish
Was thinking same thing. It should be a good week for sec shorts and roll call
  • Like
Reactions: Mike0616
R
A lot of upsets yesterday, but my LSU Tigers won.
  • Like
  • Haha
Reactions: Mike0616 and Jimbo
Foxbat
Best fan sign I saw during the ND-BYU game: "Bear ate your Lucky Charms!" (Bear being the Cougars' QB). I was going to suggest, "Have you or your team been involved in a Carr crash?"
  • Haha
Reactions: Jimbo and Mike0616
meStevo
Lifetime Supporter
Last reply · posted in The Chit Chat Club
A continuation of a thread from the pub, just general discussion of AI.

Brief 60 minute clip about next gem autonomous fighters - not remote controlled, but rather collaborating with controllers and aircraft in the theater.


View: https://youtu.be/DRm0mbp_n1k


We've literally got a movie already about this ;)


View: https://youtu.be/a2PW7a9ViDc
67 Replies · 1143 views
meStevo
Agreed, it mostly regurgitates known solutions. That's the point. Nobody needs an innovative fix for a driver error or a creative way to format a report. Let it handle the solved problems so people can spend their time on the ones that aren't.
harshness
Agreed, it mostly regurgitates known solutions. That's the point.
That's the point at which innovation ends, and there's no longer any point to software engineering other than swatting bugs that result from misapplication.
meStevo
That's the point at which innovation ends, and there's no longer any point to software engineering other than swatting bugs that result from misapplication.

Addressed by what you didn't quote. This cycle is as old as computing: compilers, libraries, frameworks each automated the tedious part, and the human work moved up a level. Innovation didn't end; it shifted. And people still make new compilers, libraries or frameworks.

Nobody's forced to hand anything off. Anyone who wants to keep doing it by hand still can, and people who couldn't do it at all now can.
harshness
... and people who couldn't do it at all now can.
Misapplication isn't something that the casual coder can identify. They can only discover, the hard way, that it doesn't work at some point.
meStevo
Misapplication isn't something that the casual coder can identify. They can only discover, the hard way, that it doesn't work at some point.
You're not wrong, but that's part of learning. Whether from others or our own mistakes, we've all learned that lesson one way or another.
harshness
Whether from others or our own mistakes, we've all learned that lesson one way or another.
I'm not sure that the school of hard knocks is the quickest or surest education to find your way.

There are many examples in the headlines of people getting burned multiple times and not wavering in their pursuit of stupidity.
meStevo
I'm not sure that the school of hard knocks is the quickest or surest education to find your way.

Good thing not everyone will have to learn the hard way then. The same tools can explain why something broke.

There are many examples in the headlines of people getting burned multiple times and not wavering in their pursuit of stupidity.

This is true of literally anything, though.

Happy to agree to disagree, but I'm already enjoying the dividends personally and helping others at work and at home do the same.
  • Like
Reactions: telstar_1
dishstaller
Been reading this thread but not commenting much, primarily because there is so much "news" out there on this topic and it is hard to tell what is real and what is theater.
My biggest problem with AI is that these agents are taught...not necessarily programmed but taught. Well, there's an old saying "garbage in/garbage out". I remember a Joe Rogan show a while back when he had Elon Musk on and they talked about AI and Elon said one of the AIs (can't remember which one, sorry) was asked which was worse, Thermonuclear War or mis-gendering Kaitlyn Jenner and it came back with the answer that mis-gendering was worse. Now forget the politics involved with all the gender stuff we have been subjected to the past few years.....to say that mis-gendering is worse than the killing of hundreds of millions, perhaps billions of human beings.....Kaitlyn Jenner included.....is simply insane not to mention incredibly dangerous.
meStevo
Been reading this thread but not commenting much, primarily because there is so much "news" out there on this topic and it is hard to tell what is real and what is theater.
My biggest problem with AI is that these agents are taught...not necessarily programmed but taught. Well, there's an old saying "garbage in/garbage out". I remember a Joe Rogan show a while back when he had Elon Musk on and they talked about AI and Elon said one of the AIs (can't remember which one, sorry) was asked which was worse, Thermonuclear War or mis-gendering Kaitlyn Jenner and it came back with the answer that mis-gendering was worse. Now forget the politics involved with all the gender stuff we have been subjected to the past few years.....to say that mis-gendering is worse than the killing of hundreds of millions, perhaps billions of human beings.....Kaitlyn Jenner included.....is simply insane not to mention incredibly dangerous.

Agents need appropriate context to make what would be understood as the correct read in a situation like that, and that Gemini answer was a clear miss on that front.

That said, we've also seen Musk (and/or his team) put his thumb on the scale (or just release a very poor product) with his own deployed AI since:


In the end, it's all a tool. Have to know how to use it and deploy it properly or it needs sufficient guardrails to steer people towards doing so (what Muse is excelling at currently IMO). I'm routinely interacting with several agents a day operating various processes locally and in services I use, and there are numerous others silently spun up to perform actions or satisfy requests from my prompts.

Related to earlier discussion in the thread on leveraging local inference: this kind of analysis happening behind the scenes is something everyone will have built into Windows, IMO. Most people won't see all of this, just the results, unless they want to dig into how the fix was chosen. Stuff like this will be standard as agents get local system access baked in, and more of the inference itself moves on-device.

1792355686329.webp
T
Good thing not everyone will have to learn the hard way then. The same tools can explain why something broke.



This is true of literally anything, though.

Happy to agree to disagree, but I'm already enjoying the dividends personally and helping others at work and at home do the same.
You invested in datacenters?
meStevo
You invested in datacenters?


Though, I do have stocks in my portfolio that benefit from data centers.
TWiT Tech Podcast Network
· posted in TWiT Tech Podcast Network
0 Replies · 13 views