Social Feed

arlo
Last reply · posted in FTA Receiver / Equipment Support
Anyone seen something like this?
Today I saw the display flickering and then went blank.
I shut off the rear switch. Then turned it back on. Nothing. But did notice the typical bad capacitor stench.
I flicked it back on and the display flickered for a fraction of a second. Then nothing.
It is sending voltage to my LNB and 8 port switch because the channel I was watching came back.

The cap doesn't look like it spewed but the unit was supposed to be new when I got it.
Looks like a quickie repair was done to it though. The 1000 uF cap is soldered to what looks like pins from a failed one instead of fixing it proper. And it looks like if the previous bad cap was swapped, there is leftover electrolyte that wasn't cleaned from the board. I don't know. Never had it opened until now.
Details!!
I can pull it and check it. And check a few other components. There was a screw and star washer floating around inside from the aluminum base plate. All of those screws look loose because its rattling around a bit.
The ground cinch connector was floating around inside too.
I was very careful opening it up. Very!

The front display connector was barely hanging on and came loose before I could snap a pic. Crap!
Anyone have a photo of how it plugs back in. There's more pins than connector. Sucks.

Brian? Any tips? It hasn't moved from its home since I had it. Is there a common place to look?
The remote and keyboard was unresponsive. It was working like a peach.
You know I'm fully equipped with a bench. Beyond basic component checks.
Same as it commonly is without a schematic. Out in the woods unless something stares me in the face.
Fluke to the rescue.

What do you think? Help!! And that front display connector. I need to know how it gets plugged back in.
20221217_214946.jpg
9 Replies · 2106 views
primestar31
arlo Sounds like you are used to re-working circuit boards. Do you have one of the over the head microscope glasses? If so, look the board over very carefully for bad, or burned, or crystalized/grainy solder joints. Use a dental pick, and if some leads don't quite look right, check them to make sure the solder didn't crystalize causing a bad joint. If so, you know what to do to fix that. Also look at tops of caps for any that look popped or humped. Check diodes to make sure none are shorted OR open.

Good luck.
  • Like
Reactions: arlo
Titanium
No longer stocking replacement boards for the ASC1, but still have most of the components on hand.

20221218_170555.jpg
  • Like
Reactions: arlo
arlo
Kind of concerned about the loose base plate screw and star washer. If that's the reason for failure if one was resting on the board.
I didn't get to it today. #1 on the list after coffee in the am.
Wondering what components are available. Board level?
I know this is a long shot and expect the reply. Is a voltage diagram remotely possible to obtain?
There's no visible board damage at first look.
Thanks so much for the display connector mating photo. It means a ton.
With diseqc seeming to work because powering it on restores a channel.
But the display dead and the unit unresponsive. Perhaps a voltage rail issue?
Pulling the mcu pinout to check dc input pins.
Titanium
No voltage schematics are available. Digikey and I both have the components to populate the PCBs.

Does the motor bump East/ West? LNB voltage switch? S1/S2 voltage? Servo voltage? AC Voltages on transformer secondary outputs measure within 10% of printed specs? AC line selector set to 115 (slide between 230 and 115 several times)?

If you have questions, please feel free to call.
  • Like
Reactions: arlo
arlo
So far. New years stuff has settled down and the bench is clear of laptops and cell phones and Xbox hdmi port replacements. <deep sigh>
Here's what I got from the xyl. It got very cold out. Right after days of rain. Like subzero cold.
She's familiar with the actuator getting "balky". What is it? "Motor Stall"? error on the LCD?
So she's used to resetting it by hiting ok to return on the remote.
She didn't tell me that the message that time was "Short"..something.
But. It reset easily and the dish moved for days. I didn't see any errors.
It was only when I said some expletives and the unit went dead that she told me that.
It did not blow the fuse. I did check the IEC plug/socket. Flicked the voltage selector back and forth a few times.
Pulled the motor wires and put the Harley battery with ammeter inline. Nothing crazy, no intermittent spikes in amperage. The dish went up to limit switch and down to limit switch smooth (but slow).

So. Just a quick check. Details later and perhaps a call, Brian. If that's cool.
Pulled both relays. Coils are good. Loaded contacts handle about 4.8 A @ 12VDC. NO&NC just fine.
Passives look good. Diodes so far check ok. But that was a quick component check last night.
I'll get more in depth. Have a good photo of the component side. Bridges look ok and bridge diode circuit looks ok.

When the time comes after coffee. An xformer check. Then power the board with current limiting.
Regulator output checks. Thermal cam check.
Did a quickie RE of the power rails on paper.

You didn't tell me there's an ASC1 hw mod page here.
R17 is actually a cap. I don't see that in the mod page.
Are there any Zeners? Knowing that would help.
U102. The LM317 closest to the xformer is kinda' wobbly. But so far no 'solder circles' detected.

Sidenote:
Never got a 22kHz switch to work at all. Never thought it may have been something in the ASC1 not passing it.
Since I got it, it has never been out of the receiver path. I attributed the switches not working to the image used.
1X8 Geosat diseqc switch always worked well. Good time to check a 22kHz switch I'm a guessing.

The very last time I tried to power it up before pulling it for the bench.
The LCD tried to illuminate and the LCD tried to startup. Then quit very fast. I didn't push it after that.
The loose screw and washer from the baseplate still freaks me out. Damn I hope it wasn't resting on the pc board.

Codewarrior is pretty interesting btw. With a 12V battery, 'sneaking up' on satellites is easy in the house. No massive overshoot and then going back the other way. A speed ramp up/ramp down, slow jog would have been the perfect afterthought. Another bean.
  • Like
Reactions: KE4EST
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in The Chit Chat Club
Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne


Get it?


An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
68529 Replies · 2672813 views
  • Like
Reactions: c-spand
long_time_Dish
You Look Like You Love Me - Ella Langley
  • Like
Reactions: dishstaller
dishstaller
See Me Feel Me - The Who
long_time_Dish
Take It Easy On Me - Little River Band
H
TAKE IT As It Comes-The Doors
ClarkGable
Take It To The Limit - The Eagles
jamieh1
Last reply · posted in DIRECTV Programming Forum
The new curated multiview is now live.
While on many of the sports channels and non sports channels there is a multi view option button. It will pull up a side bar with many different multi view options.
6 Replies · 336 views
K
It's now expanded to a Build Your Own Multiview, currently available to streaming customers with Geminis and Roku, and coming soon to Android TV, Fire TV, Vizio, LG, Apple TV and Tizen.
b4pjoe
It's now expanded to a Build Your Own Multiview, currently available to streaming customers with Geminis and Roku, and coming soon to Android TV, Fire TV, Vizio, LG, Apple TV and Tizen.
But not on the only device they ship out right now which is the Gemini Air.
  • Sad
Reactions: Jimbo
TheRatPatrol
It's now expanded to a Build Your Own Multiview, currently available to streaming customers with Geminis and Roku, and coming soon to Android TV, Fire TV, Vizio, LG, Apple TV and Tizen.
How soon will it be available on Apple TV? Thanks
I WANT MORE
But not on the only device they ship out right now which is the Gemini Air.
It's on my Air's.
b4pjoe
It's on my Air's.
The post read: "currently available to streaming customers with Geminis and Roku, and coming soon to Android TV, Fire TV, Vizio, LG, Apple TV and Tizen". It didn't mention the Air. I suppose when it said Geminis it meant both but I had no way of knowing that.
  • Like
Reactions: dtv757
dtv757
Hopefully soon for fire stick too
SuperDish_Fan23
Last reply · posted in DISH Network Support Forum
Why are ViP922s So rare? like its crazy how ebay has none, i checked everywhere, also, i got a ViP222k now, which is actually activated!
2 Replies · 54 views
dishdude
They didn't sell many, they were pricey and not out long. Quickly got replaced by the Hopper.
T
They were high-end specialty, somewhat buggy and the 612/622/722 just overwhelmed it in popularity.
Former member 208119
Last reply · posted in SiriusXM Satellite Radio
My year was almost up and we got the new bill for a year of service for $ 360.00 insane sat radio is becoming like cable!!! i logged into my acct and hopped onto chat and told the rep that i wanted to cancel. she understood my concern and went quiet for a few minutes. i figured that she was canceling my service. she comes back and said that she seen that i have been a sub since 07 and then offers me the same package for a year for 120.00 with taxes and fee's!!! i grabbed it. after almost having a stroke :biggrin
237 Replies · 11013 views
B
What i noticed with my last renewal XM is now billing me $4.99 monthly instead of one time yearly payment.
Jimbo
What i noticed with my last renewal XM is now billing me $.99 monthly instead of one time yearly payment.
Did you accidentally get on the wrong plan ?
I still do the once a year plans.
B
Did you accidentally get on the wrong plan ?
I still do the once a year plans.
I have to think maybe more people dont keep track of the monthly XM bill. Every time i renew i put a reminder on my calendar week before its time to renew. My wife told me the other day not to renew her and then i told her you are not going to be able to listen to XM at home. Then she changed her mind...!!
  • Haha
Reactions: Jimbo
TRG
TRG
I have to think maybe more people dont keep track of the monthly XM bill. Every time i renew i put a reminder on my calendar week before its time to renew. My wife told me the other day not to renew her and then i told her you are not going to be able to listen to XM at home. Then she changed her mind...!!
I get an e-mail every month reminding me that X amount will be charged to my credit card. If I see it go up I get on chat or pick up the phone. But I also remember that my year is up in December.
B
I get an e-mail every month reminding me that X amount will be charged to my credit card. If I see it go up I get on chat or pick up the phone. But I also remember that my year is up in December.
yea i don't understand WHY, like you I get a notice each month. Mine is also up in December.
Jimbo
yea i don't understand WHY, like you I get a notice each month. Mine is also up in December.
You get an email every month to let you know they are billing you for the next month.
Foxbat
Mrs. Foxbat reminded me it's that time of the year to do the Cancel Tango💃🏽

The A.I. agent appears to be better than in the past. It got to the acceptable price quicker than previous years, no human operator involved. $5/mo and I still have over $50 in SiriusXM credit from my FordPartner benefits.
  • Like
Reactions: slow_poke_pete
Peter Parker
Supporting Founder Lifetime Supporter
Last reply · posted in DISH Network Support Forum
No idea what improvements might be involved.
19 Replies · 829 views
  • Like
Reactions: LQQK and reubenray
bookworm370
Has anyone noticed an FF stutter with 713? I used to be able to hit FF a few times and skip smoothly. After 713 (maybe 712), when I skip forward, there is a definite stutter for as many times as I have pressed FF.

Can anyone check on this and report back? Recorded programs and then press skip forward a few times to see if it's smooth? Normally, it just jumps to the right place after the skips.
  • Like
Reactions: charlesrshell
N
I'm getting fabulous picture on Ch. 148 4k, but zero audio with H713. This is with a recorded show (Notre Dame game). Anyone else have this? Audio is fine on every other channel.
  • Like
Reactions: charlesrshell
R
Has anyone noticed an FF stutter with 713? I used to be able to hit FF a few times and skip smoothly. After 713 (maybe 712), when I skip forward, there is a definite stutter for as many times as I have pressed FF.

Can anyone check on this and report back? Recorded programs and then press skip forward a few times to see if it's smooth? Normally, it just jumps to the right place after the skips.
My wife mentioned that her remote is acting strange this morning. She hit FF and it went to 15x FF.
  • Like
Reactions: charlesrshell
Bobby
I'm getting fabulous picture on Ch. 148 4k, but zero audio with H713. This is with a recorded show (Notre Dame game). Anyone else have this? Audio is fine on every other channel.
This has been an ongoing issue. A fix is coming, probably in the next software version.
Foxbat
Wife bought me a t-shirt that has "have you tried turning it off and on again?"
Here's the one I need:
1792365258110.webp
dishstaller
Here's the one I need:
Just ordered one....that's great.
dfergie
Staff member HERE TO HELP YOU!
Last reply · posted in The Chit Chat Club
Stumbled across this ... http://www.gaspricewatch.com/USGas_ZipSearch.asp
I found no local prices, although it did show stations at my location...
Added these to this post...
USA National Gas Temperature Map
State By State Gasoline Taxes
Gas Buddy

Ethanol Free Stations

5552 Replies · 460659 views
Bobby
Regular$5.999​
Premium$6.399​
Diesel$7.999​
at Costco, Rohnert Park.​
  • Like
Reactions: harshness
harshness
I wonder if California is getting into the Winter formula.
dishstaller
Regular$5.999​
Premium$6.399​
Odd that out there, Prem is only 40 cents higher. Here it's a full dollar more.

Last night it was about $4.17 gas, $6,19 diesel.
harshness
Odd that out there, Prem is only 40 cents higher. Here it's a full dollar more.
On the West Coast, a 40-cent differential is common. It used to be 30 cents before the prices rose above $3.

A "full dollar more" sounds like it may be boat gas (non-alcoholic), which is a whole different discussion.
  • Like
Reactions: Foxbat
Foxbat
Here in Indiana, the difference between Regular and Premium is usually a dollar, but some charge even more:
1792374072446.webp
  • Like
Reactions: dishstaller
dishstaller
A "full dollar more" sounds like it may be boat gas (non-alcoholic),
Both non-ethanol and prem run about the same....buck more. When we were up in TN it was a buck more up there as well.
jokeworm
Last reply · posted in What's Cooking?
Ok, I'm bored .... actually - to be more precise - I'm bored of eating the same rotation of 9 or 10 meals that are currently my "go-to" meals. My wife works the long hours - I work from home as and when i feel like it ... which means i generally do most of the cooking ... and so by default - i also make out the shopping list ...

We cook at home 5 or even 6 nights a week - but we always seem to fall back on the same old tried and tested "quick and easy but tastes ok" meals. Week in week out.

Pot Roast - mash and Peas.
Spaghetti
Chicken Pasta in cheese sauce.
Curry & rice
(these are some of mine)

Now it's not that I'm not adventurous in the kitchen ... I'll try anything once or twice ... but we all do it. Unless your name is Martha Stewart or Rachel Ray .. we all eventually fall back on our 8-10 favorite "meals"

So i thought - if we shared some of our own go-to meals with each other ... we might be able to add a few "new" ones to our own arsenal of meals.

So again - I ask you ...

What's for dinner tonight ?

Please give me something new to add to my rotation ... its our weekly shop tomorrow - so i want to pull together a few idea's and try and eat a meal each day next week that I've never had before .. or at least something that is not on my current "go-to" meal plan.

What meal do you always seem to fall back on in your house ? Maybe its something that I've never tried or not had in a while. I need inspiration !! I've got a blank shopping list in front of me - and nothing sounds good .. HELP !
4332 Replies · 331193 views
TRG
TRG
Beef and vegetable stew with buttermilk biscuits. Water.
It seemed appropriate on an unusually cold and wet evening in New Mexico.
  • Like
Reactions: dfergie
Bobby
Chili Cheesebugers, Tater Tots.
  • Like
Reactions: dfergie and TRG
TRG
TRG
I made shrimp parmesan with spaghetti and a salad.
  • Like
Reactions: dfergie
S
venison lasagna
  • Love
Reactions: Bobby
dishstaller
Smoked some salmon on the grill while enjoying some Blue Moon beer. Kinda cool tonight so I fired up the heaters. Here in FL, we fire up heaters once the temps get below 60 :cool As for the salmon, I seared them first, then flipped them off to the side not over the coals and brushed on some lemon pepper marinade followed by some salmon seasoning. Threw some hickory chips on the coals and then closed the vents to about 10% airflow. Yum.
  • Like
Reactions: dfergie and Bobby
osu1991
Pub Member / Supporter
Last reply · posted in The Chit Chat Club

The number-one US state for EV growth, according to the June 22 Yardi report?
Oklahoma.


:eek


It has no ZEV mandates and "minimal" incentives, Yardi says, but also has cheap electricity, high multi-car household rates (so, for example, a non-Lightning Ford F-150 pulls their trailers), and a consumer base willing to switch.
112 Replies · 905 views
navychop
Servant's problem.
  • Like
Reactions: Bobby
meStevo

Never realized that Tesla is losing to BYD at manufacturing too, which IMO is Tesla's biggest accomplishment and area of innovation. Nice writeup about the state of play and how we got here though. I have no faith that we're moving any productive direction though sadly, most changes and efforts feel reactionary rather than rooted in making use of the time being bought by tariffs, with few exceptions.

So: how are the cars so cheap, and what is being cut to get there? The best public accounting comes from the Rhodium Group, which compared BYD, Geely, and Leapmotor against Tesla's Chinese operation, a fair comparison because it removes labor costs and shipping from the equation entirely. Their estimate is that BYD builds a car for about $4,700 less than Tesla builds a Model 3 in Shanghai, roughly 15 percent of the Model 3's price. The breakdown is the interesting part. Direct government grants account for about $292 per vehicle, which is 5 percent of the gap. The biggest single factor is vertical integration: BYD makes about 80 percent of its top-tier components in-house, against 37 percent for Tesla, and that eliminates roughly $2,369 per vehicle in supplier markups. Lower overhead, meaning cheaper engineering talent and administrative cost spread across enormous volume, accounts for another $1,719. And BYD pays its suppliers on 155-day terms, against Tesla's 60, which is worth about $214 per car in float. When people say the Chinese advantage is subsidies, the per-vehicle number says otherwise. When people say it is slave wages, the Tesla Shanghai comparison says otherwise too. The advantage is mostly that BYD decided, twenty years ago, to make its own batteries, its own motors, its own power electronics, and its own semiconductors, and Western automakers decided the opposite.​
harshness
The EV company to watch out for is SAIC. They seem likely to take over Government Motors at some point.

GM originally struck a JV deal with SAIC to gain access to China. Now SAIC has taken China back with the substantial library of technology GM shared and they're looking to export to Mexico, South America, the Middle East, and Asia-Pacific.
osu1991
  • Like
Reactions: Foxbat and AZ.
TWiT Tech Podcast Network
· posted in TWiT Tech Podcast Network
0 Replies · 32 views
Ham Radio 2.0
· posted in Ham Radio 2.0
0 Replies · 25 views