Social Feed

Stuart Sweet
Staff member HERE TO HELP YOU! Pub Member / Supporter Cutting Edge
· posted in The Solid Signal Blog
Folks, here's something I was forced to consider. I've been answering this question, almost this exact question, for over 35 years. I was recently reminded of a time when someone asked me all the way back in the 1980s if it was possible to send your cable TV to the second floor wirelessly. Sadly, it wasn't possible then. In truth, it's really not possible now, at least on a boat. There are some solutions today that work in specific cases, but chances are marine isn't one of those cases.

Why wireless transmission doesn't work


The first thing you need to know is that obviously it's possible to send large volumes of data wirelessly. You do it all the time with Wi-Fi. But it's not possible to do it with TV. It's almost like the powers that be have thought of every possible way to do it and found ways for them not to work on your boat.

Just plain wireless transmission doesn't work


It's not legal to rebroadcast TV signals in the same frequency range they are normally in. It's against the law in pretty much every country which has laws about this stuff. Rebroadcasting is also internationally illegal, thanks to agreements between countries. If everyone could rebroadcast using regular TV frequencies, it would be mass chaos and no one would be able to receive anything over the air. It's just not done.

Translating to Wi-Fi doesn't work


Back in the 20th century you might remember a device called an "RF Modulator" which let you move TV signals from room to room over a cable. Today, these things are incredibly expensive due to licensing and copyright protection that's built into TV signals. However, with enough money it's possible to have modulators that send signals over IP networks. Theoretically it might even be possible to translate that IP data to Wi-Fi. I can't see why it wouldn't be. However, in practice it's just so costly that it's not likely to be doable.

Wireless HDMI doesn't really work, especially on boats


You might see some devices called Wireless HDMI adapters on some of the other sites. They will work on unencrypted signals over fairly short range. However, all satellite data is encrypted and so unless you're prepared to dip into the hacking world to remove that encryption, they won't work for satellite. Not only that, but those devices don't work well at all on boats. There's too much material in the walls to block signals.

Here's the option that does work


It may not be what you want to hear, but the best way to get satellite TV throughout your boat is to wire it as it's supposed to be wired. There are no shortcuts here, unfortunately. There's no reliable way to bypass the need for a cable that goes into each cabin. With DIRECTV and DISH, you can generally use inexpensive splitters to avoid running wire from every cabin back to one closet. But you won't be able to get away without running that one wire.

Our marine team has better news, though


There are a lot of options for entertainment on your boat. There are more options now than ever before. And, there's one place you're going to find the experts who can talk about them. Signal Connect has done more marine tech activations than anyone else in the world! Call the experts at 888-233-7563 during East Coast business hours. They'll put their decades of experience to work making sure you've got the entertainment and communication you need. We're ready to help! Call now, or if it's after business hours fill out the form below. We'll get right back to you!


The post Can you distribute satellite TV wirelessly throughout your boat? appeared first on The Solid Signal Blog.

Continue reading...
0 Replies · 401 views
dfergie
Staff member HERE TO HELP YOU!
Last reply · posted in What's Cooking?
We have a Breakfast and Dinner thread so... :)
Continuing from the Breakfast thread, found Cornbread mix so ...
Yellow Cornbread Mix
2 Hatch Green Chiles -diced
1 Egg
2/3 cup of milk
add to greased pan
Bake for 400f 20-25 minutes(From instructions)
now to put together and try... this to go with pinto beans...
5448 Replies · 336076 views
M
Garlic cheese bread
Green beans
Apples
Chocolate Milk
Some weird noodles. ;)
(They have salad and a couple other fruits if wanted)
  • Like
Reactions: dfergie
TRG
TRG
Club sandwich and corn chowder. Iced tea.
dfergie
Chili dog bowl, water… (homemade chili)
TRG
TRG
Leftover wanton soup and pork fried rice. Water.
dfergie
IMG_5955.webp

Sweet tea…
  • Like
Reactions: TRG
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in The Chit Chat Club
Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne


Get it?


An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
68658 Replies · 2680216 views
  • Like
Reactions: c-spand
dishstaller
I Wanna Talk About Me - Toby Keith
  • Like
Reactions: RaiderPower
Bobby
98.6 - Keith
harshness
I'm Easy - Keith Carridine
  • Like
Reactions: RaiderPower
gms49ers
It's Easy - Boston
RaiderPower
Take It Easy On Me - Little River Band
  • Like
Reactions: dishstaller
R
Last reply · posted in Computers and Gadgets
Lately my eight year old Dell laptop has been shutting off even when I have a full battery. I have had to keep it plugged up all the time to keep this from happening. Any idea what is causing this? I replaced the battery about three years ago.
2 Replies · 46 views
arlo
A recalibration might be needed. Even if it shows full, the individual cells may have become unbalaced. And the BMS chip in the battery reports false information to the pc.
Try this. Start it up in the bios/uefi and leave it there until the battery dies and it shuts off.
It might just keep running longer than in Windows. Or run for a short while and shut off.
If it's the first case. Probably just needs a balancing. If the latter, the pack might just be dead.
Not throwing stones but perhaps just a cheaply constructed battery with substandard cells. Could be.

Patience. Keep restarting it in bios/uefi until it won't fire up anymore.
Then plug the charger in and let it complete a full charge. And see what happens. If it's better.
Do the same thing one more time. Run it until it dies dead-dead. Then just let it charge, pc shut off.
When charged, it might be better. It might not be.

There are bench jigs that read the actual BMS and override it to let a tech manually monitor and charge the separate packs. They can also reset any "time bombs" in it that cause an otherwise good pack to show bad.
Maybe Santa will be good to me some year.

You might just need a new battery. Maybe the PC power management chip is going. A Dell common thing.
Leaving a laptop plugged in with a full battery is known to reduce the life. Asus for one recommends that you don't leave the charger plugged in all of the time even when shut down. And setting Windows to charge the battery to 85% instead of 100% increases life.
That's all I got.
dishstaller
That's all I got.
That was quite enough....I definitely learned something from your post. Thanks
TRG
TRG
Pub Member / Supporter
Last reply · posted in Computers and Gadgets
I set up a music server for my brother a few years ago. It's basically a small headless computer but it needs to have a DHCP IP address reserved for it in the router settings. This was easy to do in his DSL router. He's switching to Starlink now and I was wondering if these setting are easily accessible in the Starlink router. I'm pretty sure he will be getting the latest V5 router.
5 Replies · 284 views
b4pjoe
I set up a music server for my brother a few years ago. It's basically a small headless computer but it needs to have a DHCP IP address reserved for it in the router settings. This was easy to do in his DSL router. He's switching to Starlink now and I was wondering if these setting are easily accessible in the Starlink router. I'm pretty sure he will be getting the latest V5 router.
If you can't get into the router to reserve an IP address just don't use DHCP on the device that needs connected and assign it to a specific IP address in the network settings.
  • Like
Reactions: harshness
HipKat
I set up a music server for my brother a few years ago. It's basically a small headless computer but it needs to have a DHCP IP address reserved for it in the router settings. This was easy to do in his DSL router. He's switching to Starlink now and I was wondering if these setting are easily accessible in the Starlink router. I'm pretty sure he will be getting the latest V5 router.
They are not. Your best bet is to set up a third-party router, attached to the Starlink for your server, that you can get into, like a Linksys, etc
  • Like
Reactions: Foxbat
Foxbat
…it needs to have a DHCP IP address reserved for it in the router settings. This was easy to do in his DSL router. He's switching to Starlink now and I was wondering if these setting are easily accessible in the Starlink router. I'm pretty sure he will be getting the latest V5 router.
The Starlink V5 Install Kit I just got comes with the Mini Router. It is pretty limited in what it can do. For example, it can provide only one IP subnet at a time, no Guest Network, but it does support the pass-thru to a third-party Router. You can also split the Wi-Fi into separate 5 GHz & 2.4 GHz SSIDs to help some IoT devices that don't support 5 GHz bands to work.

The larger Starlink Router that still comes with the V4 Kit does support a Guest Network with separate IPv4 Subnet, but it's $120 from Starlink. And it still won't do DHCP Reservations.
harshness
If you can restrict the DHCP address space to assign addresses to one end of the subnet (i.e. x.x.x.50+), you can manually assign the IP address on pretty much any operating system. This is a default behavior on several popular routers. As the Router Mini only supports 235 devices, I expect that's already done.

Another option is to use a router that supports PoE to power the antenna. This article discusses that option (under PoE Power heading):

  • Like
Reactions: Foxbat
Foxbat
Now that I've had the v5 kit with the Mini Router, it's not as bad as I first thought. Yes, no DHCP reservations, but you can set up multiple SSIDs that have separate IPv4 subnets, and like the big brother, you can select from 192.168.x.0/24 or 10.x.0.0/16 (where "x" is 1-4).

You can also split a subnet and have different SSIDs for the 5 GHz and 2.4 GHz channels to handle some IoT devices. I haven't discovered what subnet the 2nd NIC on the router assigns, I'm guessing it's the first subnet.
dishstaller
Pub Member / Supporter Lifetime Supporter
Last reply · posted in The Chit Chat Club
2 Replies · 51 views
dishstaller
Sorry for posting the wrong link. Just corrected it.
dishstaller
Pub Member / Supporter Lifetime Supporter
Last reply · posted in The Chit Chat Club
Terrible tragedy. You would think that they would have safe guards in place that would prevent something like this from happening. I guess if you are going to ride in a passenger train it might be best to get a car near the rear.

2 Replies · 55 views
  • Sad
Reactions: Jimbo
Jimbo
Terrible tragedy. You would think that they would have safe guards in place that would prevent something like this from happening. I guess if you are going to ride in a passenger train it might be best to get a car near the rear.

They will have to look at the switching sections to determine WHY 2 trains were on the same track ... at the same time.
dishstaller
Thought this article might be of interest to some of you who might travel via train.