Social Feed

tcpuccio1
Last reply · posted in DISH Network Support Forum
Hello and thanks in advance for any replies.

Have a dish network hopper with a dish that had a hybrid twin ea.2 head on the dish. I'm in NY my zip is 14086. what kind of signal strength shough I see on a clear day. I have a clean view to the southeast horizon. the system is maybe 6 years old. I noticed this past week I kept getting a message weak signal switching to internet happen first time watching MNF on espn. I think the software on the hopper has changed it's not what I remember it only shows 2 satellites now 72 and 65.1 nothing else. I swear it had a slew of them at one point in time not any more it has the thing to change which of the 16 tuners you want to check and transponder etc... obviously, I want the strongest signal I can get scrolling though the tuners they all seem to have different signals strength depending on which tuner I select? how can that be? if where I am on the globe depends on how strong a signal, I can get I'm fine with that. it's been a super-hot and dry summer here and seems like there was some settling with the ground around my house possibly the pole I have it on moved some. so obviously don't loosen up everything at the same time. move the degrees on the compass fist then the tip and tilt? does it matter which one is moved first to try to get the best signal. when this was acting up I looked and the signal strength was under 50%
4 Replies · 468 views
NYDutch
Most likely your dish needs to be peaked up. First, I would make sure the pole is completely plumb, truing it up as needed. Then, if still needed, I'd suggest gently pulling/pushing on the top and then the side of the dish while someone watches the signal level. Note any changes for the better and loosen the bolts to slightly move the dish in that direction. The skew should not need readjusting.

You were previously seeing the 77 sat listed along with the other two, but 77 has been decommissioned for CONUS use. Signal levels vary from transponder to transponder due to spot beam differences and transmitter power variations.
NYDutch
Most likely your dish needs to be peaked up. First, I would make sure the pole is completely plumb, truing it up as needed. Then, if still needed, I'd suggest gently pulling/pushing on the top and then the side of the dish while someone watches the signal level. Note any changes for the better and loosen the bolts to slightly move the dish in that direction. The skew should not need readjusting.

You were previously seeing the 77 sat listed along with the other two, but 77 has been decommissioned for CONUS use. Signal levels vary from transponder to transponder due to spot beam differences and transmitter power variations.
On re-reading your post, since you have a hybrid twin LNBF, you were only seeing the 61.5 and 72.7 sats. I think you're confusing the transponder listings with the sat listings.
tjboston5676
The signal strength isn't really a percentage. For eastern arc is normal to be anywhere from 45-60 depending on location. You'll start having issues under 35. So if it's currently in the 40s you may have a loose mount and it's wobbling around in the wind. Just call dish up and have tech come check it out. If you don't have protection plan you can argue with them and they'll usually offer a free month of protection plan or waive the service call fee.
Former member 208119
were getting 65-66% signal with our dish 500 with WA DPH Twin LNBF...
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in DIRECTV General Forum
The following is from Reddit. -
View: https://www.reddit.com/r/DirectvStream/s/orzHBkmqQW


gemini.webp

There appears to be a new DIRECTV Gemini OTT box, the C81KW-650.

The FCC listing is partially available, and a Geekbench entry confirms it uses an Amlogic S905X5, a solid SoC for a set-top box.

I also see 4GB of RAM, and the manufacturer is SEI Robotics.

DIRECTV C81KW OTT Box - Android TV Guide

Ok found a picture of the Box too on Reddit:


View: https://www.reddit.com/r/DirectvStream/comments/1twlex0/comment/opzeqi1/
15 Replies · 753 views
  • Like
Reactions: dtv757
GRB1959
A new Gemini box for DirecTV streaming possibly becoming available in January of 2027? That would be welcome news.

I have been exploring leaving Dish DBS ever since a software update around Aug. 10, version H711 and now H712, is causing problems with IR signals and the Dish Hopper 3. As a result my Sofabaton X2 universal remote no longer works perfectly as it did prior to the H711 and H712 Dish Hopper 3 firmware updates.

I have been a little leary of the current hardware available for DirecTV streaming as the Gemini Ospry box fits my needs, however they are getting a little long in the tooth and finding the 4GB RAM (SKU: 60233) Osprey box complete with remote and power cable is somewhat challenging. I see that the 2GB RAM Osprey boxes (SKU: 60164) can be found on Ebay and at Walmart online used, however a 4GB Osprey box is preferred.

Now I wonder if I should just wait it out until the new Gemini box for DirecTV streaming becomes available. I want a box with an Ethernet port and the Gemini Air is WiFi only. If the new Gemini box does become available in January of 2027 will it be lease only via DirecTV or will we be allowed to purchase them?
S
A new Gemini box for DirecTV streaming possibly becoming available in January of 2027? That would be welcome news.

I have been exploring leaving Dish DBS ever since a software update around Aug. 10, version H711 and now H712, is causing problems with IR signals and the Dish Hopper 3. As a result my Sofabaton X2 universal remote no longer works perfectly as it did prior to the H711 and H712 Dish Hopper 3 firmware updates.

I have been a little leary of the current hardware available for DirecTV streaming as the Gemini Ospry box fits my needs, however they are getting a little long in the tooth and finding the 4GB RAM (SKU: 60233) Osprey box complete with remote and power cable is somewhat challenging. I see that the 2GB RAM Osprey boxes (SKU: 60164) can be found on Ebay and at Walmart online used, however a 4GB Osprey box is preferred.

Now I wonder if I should just wait it out until the new Gemini box for DirecTV streaming becomes available. I want a box with an Ethernet port and the Gemini Air is WiFi only. If the new Gemini box does become available in January of 2027 will it be lease only via DirecTV or will we be allowed to purchase them?
there leased at 10.00 per box. unless you can find em at ebay or wally world where people have gotten em before. or you could get a roku apple tv firestick if you don't need the channel numbers
GRB1959
there leased at 10.00 per box. unless you can find em at ebay or wally world where people have gotten em before. or you could get a roku apple tv firestick if you don't need the channel numbers

I appreciate the reply. My wife will be using this as well so a numeric keypad to change channels that actually works is a must and I want it to have a hardwired Ethernet port so that leaves the Gemini box as my only real choice.
S
I appreciate the reply. My wife will be using this as well so a numeric keypad to change channels that actually works is a must and I want it to have a hardwired Ethernet port so that leaves the Gemini box as my only real choice.
oh and channel master did make a numeric keypad for the apple t.v. i don't know if they still do and if that would work with dtv channel numbers!
  • Like
Reactions: GRB1959
K
The DTV app doesn't respond to channel number inputs on 3rd party devices.
S
The DTV app doesn't respond to channel number inputs on 3rd party devices.
This is good to know!!!
Tom Speer
PUBLIC INFORMATION SUMMARY: DIRECTV's New Streaming‑Only Device (Model C81KW‑650)

I asked ChatGPT to summarize what is publicly known about DirecTV's new Streaming box. Here is what it said:

DIRECTV has a new streaming‑only device undergoing testing, publicly identified as model C81KW‑650.FCC filings and Reddit posts show it uses an Amlogic S905X5 chipset with 4 GB RAM, 64 GB storage, Wi‑Fi 6, Ethernet, and support for modern codecs including AV1 and H.266.It runs Android TV 14 and is manufactured by SEI Robotics.

Performance is significantly improved over the Osprey‑based Gemini and Gemini Air, with a faster CPU, stronger GPU, double the RAM, modern codec support, and better connectivity.

The FCC lists it as an OTT device, and all public information indicates it is intended for streaming service only.No official release date has been announced.

Making it also function as a Genie client would only be a matter of software, but that would not be able to use all the advanced codecs built into this device. That is clearly not a near term priority for DirecTV, if they ever do it at all.
b4pjoe
Here is what Google Gemini says about it:

The DIRECTV Gemini V2 (Model C81KW-650) is the successor set-top box to DIRECTV's original Gemini hardware (C71KW). Manufactured by SEI Robotics, details about the device emerged through FCC filings and hardware benchmarks.




It represents a significant performance upgrade over previous DIRECTV hardware.




Hardware & Performance Upgrades

  • Processor (SoC): Powered by the Amlogic S905X5 chipset featuring a quad-core ARM Cortex-A510 CPU (2.0 GHz). This offers roughly a 35–40% performance increase over the older Broadcom chipsets, resulting in much faster app load times and UI responsiveness.



  • Graphics: Upgraded to an ARM Mali-G310 GPU.
  • Memory & Storage: Equipped with 4GB of RAM and 64GB of internal storage—a substantial jump from previous models that allows smoother multitasking and plenty of space for third-party streaming apps.

Software & Connectivity

  • Operating System: Runs Android TV 14 out of the box.



  • Wi-Fi Upgrade: Includes Wi-Fi 6 (802.11ax) support, replacing the older Wi-Fi 5 standard for more stable wireless 4K video streaming.



  • Expanded Codec Support: Supports 4K Ultra HD with AV1, VP9, H.264, HEVC/H.265, and support for future-proof VVC/H.266 video playback.



  • HDR & Audio: Supports Dolby Vision and HDR10+.

Core Ecosystem Features

  • DIRECTV Experience: Retains full integration with DIRECTV's unified interface—combining live satellite or internet channel guides with third-party streaming apps downloaded via the Google Play Store.
  • Voice & Smart Controls: Built-in Google Assistant voice navigation and Google Cast support.
dishstaller
Pub Member / Supporter Lifetime Supporter
· posted in The Chit Chat Club
I've always been super interested in things space related so this is a pretty cool event coming up. Nov 18, 2026 early in the morning, Voyager 1 will reach the distance of one full light day from Earth. Took almost 50 yrs. I was 13 when it launched.


View: https://www.youtube.com/shorts/gjHK3clOwIw?feature=share
0 Replies · 13 views
  • Like
Reactions: Keith Brannen
S
· posted in General Home Theater Equipment
Hey everyone,
I got the all important spousal buy-in to get all my equipment back out for Sat, Terrestrial reception. The catch is that I can't add any more equipment to our main house and everything will stay in the out building ~250 feet from our house. My idea is to use the server I already have to encode the feeds from multiple sources into streams that I can then watch via plex in the main house. Has anyone done this or know of any decent turn key solutions?
0 Replies · 13 views
T
Last reply · posted in C-BAND Satellite Discussion
Howdy folks long time no write.

Issue(s): Horizontal transponders (esp. Weigel mux) breakup/mosaic/sputtering audio, JTV less so (but received perfectly up until a month or so ago.
Vertical is fine (Daystar). Up until recently couldn't even get any signal on Weigel Mux but JTV was perfect.

What I did to improve things: A slight westward move improved reception but only slightly (approx 72 on the micro HD, sorry no dB to post). I removed the 3-way C-Band splitter and used a 2-way to get a 1-2 db signal gain ( the power port goes to the Startrak - the micro HD doesn't have enough juice ! (1st clue) even after swapping the switching power supply it came with with a heftier linear 12 V supply (less RFI too !).
I have had issues with the uHD before signal breaking up that a reboot would clear up (clue #2 = dying tuner?) - FYI, I reinforced the IF input and removed all flux from the pcb completely with a Flux Removal Pen (MG Chemicals Cat No. 4140-P) which definitely makes a huge difference.

I went outside and pushed and pulled reflector slightly and no improvement. Pole (actually tower in yard - the neighbours love me..NOT) is plumb, checked with carpenters level. Dish was last peaked in 2017 or so, after overhauling 24" Von Weise, new Acme, fresh grease, etc. Focal length, f/d ratio etc meticulously adjusted. One panel has a tear so planning to repair that this weekend when my cousin comes over ( to help me out (old guy here) forecast calls for sunshine.

What has changed: My utility company has installed new high tension line poles (one smack dab in the middle of 101°W target! But they put it in last year and reception (of JTV (HOR) at least) was fine, BUT when they came out to transfer the wires over this year from the old (sawed in half) pole that's about when the troubles started (coincidence?), but again Daystar (VER) was fine. I always had this pole in the light of sight of 101° before with no issues. (fyi my zenith sat 74° is unobstucted, but can't test)

In the meantime Weigel mux is trying to break in MOSTLY in LATE at night (less cell usage?) (audio not video except for a frame here or there) so don't know what has changed with this mux which suddenly "woke up". I have never had to fuss with dish moves on this satellite ( the slightest move +/- motor clicks loses lock, wheres normally on C-band I can go significantly wider east or west and still have a strong signal ( have these gone "spot beam" or narrower somehow and what is the slight difference in Az listed on Lyngsat to 100.9° affect things ( isn't that the declination i.e. requiring a tweak of declination?).

Long story short (too late, ha), if I had another DVB-S2 box to try and / or a newer more stable PLL lnb ( I have been meaning to upgrade many a time but never got arround to it) I could determine if it's my antiquated receiving equipment, or my dish/feed alignment ( doubtful as it tracks everything from 55 °W to 133 ° W nicely.) or the dreaded 5G! (BUT only on HOR and not VER?).
I read another post where the OP (with his smaller 7.5 footer) played around with the illumination to peak desired transponder and reduce qrm on interfering/ stronger xpndrs (even on 103° W). So will play with that too - and cut away the RG-6 a and pull up a fresh section with new PPC and coax Seal. Open the throat cap see if any cobwebs are there and check servo operation (also changed in last maintence 10 years ago).

Finally, this will probably be the last chance I get to play with the BUD from the looks of it (providers leaving, auctioning off rest of spectrum imminent above 4.0 Ghz, and to keep the peace with neighbours so it would be nice to have that mux back for the long, cold and dark winters to comfort this old man before I call it quits and buy a VHF/UHF/FM Yagi and get MeTV, H&I from my Vermont local stations (checked at a friends today and they come in nicely - except ABC) .
Only one guy in town (Montreal) I may be able to get a receiver or PLL lnb from to try (RPS Sat) so hopefully with elimnate that as a possible culprit. Be nice to pick up a cheap or used PLL lnb to try w/o 5G BPF (money is tight )

Like others I couldn't care less about "tv" (well maybe just a liitle or a lot) it's the challenge that excites me , I can get MeTV other ways OTA (no pirate crap).

So what do you guys (and gals) think ?. p.s. I don't have a spectrum analyzer and there are def/ cell towers nearby (half a Km or so away).
Oh and time permitting will hammer out dings too and wire damaged mesh on one section for an extra dB or two. Hesitate to touch Declination, Elevation and pole mount but will play around with those a little too... Why is this mux for finicky suddenly ?(8psk, 5/6 fec, beamwidthetc.. man wish they went back to VER I think everthing would be fine! For the engineers out here does 5G QRM affect one poliarization (HOR) more than another (VER)? I understand the strong interference swamps out the input mixer/local oscilator in the hapless old C-band lnb (I think it at time affect KU too esp. LPB on 101°W KU - incidentally thos were weak or "gone' but are back almost at the time MeTV improved..hmm Terrestrial interference?

Any thoughts or suggestions ( cheap or free solutions please) greatly appreciated. Cheers.

p.p.s. Micro HD can't display Decades and Toons but records them fine so I can watch on another box/media player (Ali chip set issue). Another reason to upgrade.

Anybody interested in a nice C/KU system free ? (for next Spring/Summer 2027)

[Sami 10' mesh, Corotor II+, Eagle Aspen (very old) C-band lnb, Norsat Ku lnb, Channel Master C/Ku (H/V) switch, Startrak 400 Analog receiver w/ motor control, Geosat uHD DVD-S2, CW600S for Mpeg-2]
13 Replies · 514 views
B
Howdy folks long time no write.

Issue(s): Horizontal transponders (esp. Weigel mux) breakup/mosaic/sputtering audio, JTV less so (but received perfectly up until a month or so ago.
Vertical is fine (Daystar). Up until recently couldn't even get any signal on Weigel Mux but JTV was perfect.

What I did to improve things: A slight westward move improved reception but only slightly (approx 72 on the micro HD, sorry no dB to post). I removed the 3-way C-Band splitter and used a 2-way to get a 1-2 db signal gain ( the power port goes to the Startrak - the micro HD doesn't have enough juice ! (1st clue) even after swapping the switching power supply it came with with a heftier linear 12 V supply (less RFI too !).
I have had issues with the uHD before signal breaking up that a reboot would clear up (clue #2 = dying tuner?) - FYI, I reinforced the IF input and removed all flux from the pcb completely with a Flux Removal Pen (MG Chemicals Cat No. 4140-P) which definitely makes a huge difference.

I went outside and pushed and pulled reflector slightly and no improvement. Pole (actually tower in yard - the neighbours love me..NOT) is plumb, checked with carpenters level. Dish was last peaked in 2017 or so, after overhauling 24" Von Weise, new Acme, fresh grease, etc. Focal length, f/d ratio etc meticulously adjusted. One panel has a tear so planning to repair that this weekend when my cousin comes over ( to help me out (old guy here) forecast calls for sunshine.

What has changed: My utility company has installed new high tension line poles (one smack dab in the middle of 101°W target! But they put it in last year and reception (of JTV (HOR) at least) was fine, BUT when they came out to transfer the wires over this year from the old (sawed in half) pole that's about when the troubles started (coincidence?), but again Daystar (VER) was fine. I always had this pole in the light of sight of 101° before with no issues. (fyi my zenith sat 74° is unobstucted, but can't test)

In the meantime Weigel mux is trying to break in MOSTLY in LATE at night (less cell usage?) (audio not video except for a frame here or there) so don't know what has changed with this mux which suddenly "woke up". I have never had to fuss with dish moves on this satellite ( the slightest move +/- motor clicks loses lock, wheres normally on C-band I can go significantly wider east or west and still have a strong signal ( have these gone "spot beam" or narrower somehow and what is the slight difference in Az listed on Lyngsat to 100.9° affect things ( isn't that the declination i.e. requiring a tweak of declination?).

Long story short (too late, ha), if I had another DVB-S2 box to try and / or a newer more stable PLL lnb ( I have been meaning to upgrade many a time but never got arround to it) I could determine if it's my antiquated receiving equipment, or my dish/feed alignment ( doubtful as it tracks everything from 55 °W to 133 ° W nicely.) or the dreaded 5G! (BUT only on HOR and not VER?).
I read another post where the OP (with his smaller 7.5 footer) played around with the illumination to peak desired transponder and reduce qrm on interfering/ stronger xpndrs (even on 103° W). So will play with that too - and cut away the RG-6 a and pull up a fresh section with new PPC and coax Seal. Open the throat cap see if any cobwebs are there and check servo operation (also changed in last maintence 10 years ago).

Finally, this will probably be the last chance I get to play with the BUD from the looks of it (providers leaving, auctioning off rest of spectrum imminent above 4.0 Ghz, and to keep the peace with neighbours so it would be nice to have that mux back for the long, cold and dark winters to comfort this old man before I call it quits and buy a VHF/UHF/FM Yagi and get MeTV, H&I from my Vermont local stations (checked at a friends today and they come in nicely - except ABC) .
Only one guy in town (Montreal) I may be able to get a receiver or PLL lnb from to try (RPS Sat) so hopefully with elimnate that as a possible culprit. Be nice to pick up a cheap or used PLL lnb to try w/o 5G BPF (money is tight )

Like others I couldn't care less about "tv" (well maybe just a liitle or a lot) it's the challenge that excites me , I can get MeTV other ways OTA (no pirate crap).

So what do you guys (and gals) think ?. p.s. I don't have a spectrum analyzer and there are def/ cell towers nearby (half a Km or so away).
Oh and time permitting will hammer out dings too and wire damaged mesh on one section for an extra dB or two. Hesitate to touch Declination, Elevation and pole mount but will play around with those a little too... Why is this mux for finicky suddenly ?(8psk, 5/6 fec, beamwidthetc.. man wish they went back to VER I think everthing would be fine! For the engineers out here does 5G QRM affect one poliarization (HOR) more than another (VER)? I understand the strong interference swamps out the input mixer/local oscilator in the hapless old C-band lnb (I think it at time affect KU too esp. LPB on 101°W KU - incidentally thos were weak or "gone' but are back almost at the time MeTV improved..hmm Terrestrial interference?

Any thoughts or suggestions ( cheap or free solutions please) greatly appreciated. Cheers.

p.p.s. Micro HD can't display Decades and Toons but records them fine so I can watch on another box/media player (Ali chip set issue). Another reason to upgrade.

Anybody interested in a nice C/KU system free ? (for next Spring/Summer 2027)

[Sami 10' mesh, Corotor II+, Eagle Aspen (very old) C-band lnb, Norsat Ku lnb, Channel Master C/Ku (H/V) switch, Startrak 400 Analog receiver w/ motor control, Geosat uHD DVD-S2, CW600S for Mpeg-2]
I had the EXACT same problem happen to me with 101w, MeTV mux (Weigel). Working great when about 3 weeks ago I started to get the pixelating, especially at night. Sometimes Jewelry TV would also do it, sometimes not. Tweaked my dish. I have a Titanium 240 feed with the 5G filter 4.0-4.2 band pass. Every other satellite is working fine. Something on their end for sure. Power reduction? My signal seems fine like always. Running a Winegard 8.5 ft dish using a GT Media UHD V8. I'm sure my receiver isn't maybe sensitive enough for lower signal levels. Frustrating here too. I'm in the Canton, Ohio area. Thanks!
arlo
To me it looks like all of the intelligent things to diagnose the problem 'on the cheap' are being done.
I have my own thoughts of lnbf's using an external filter between the feed and coax. It would be cool to see what Brian could add.
Do his units have the filter before the actual LNA chip in the circuit? In other words, signal is focused at the lnbf throat. The probes for h & v polarity send the signal to.......filtering......then to the lna IC......
Or probes, lna, then filtering. Makes sense to trap the bad stuff before amplification to me.

On the cheap sometimes leaves questions. Enosat and El Bandido both use dvb-s pci cards and TBS USB receivers.
With those, and software. Signal analysis becomes sort of easy. Or tapping into your coax with a dc pass splitter, decoupling capacitor, and using a spectrum analyzer. Tuning across the LO band. Finding signal spikes. Digging deep.

Still making my decision on a (most probably) TBS PCIe tuner card. But I have tapped into my coax with my ancient but quite impressive HP spectrum analyzer and tinysa.
I don't have 5G interference so far that I know of. But have my suspects because I'm only able to snag signal from 131W in the winter when the leaves drop. But out of curiosity do scan it in the fall. And seem to be getting a signal that 'shouldn't' be there and a scan shows no channels. Far as I got.

An idea pops up to rig up an LNBF on a stick. Along with the tinysa and power supply and do some rogue signal searches. War Driving, of sorts. But. I wouldn't think that a chinabox, firmware based receiver would be of much help.
From what I see scanning across the frequency band. 5G cell transmission is always on and is very wide spectrum.
Whether anyone is actually using talking, texting, watching stupid human tricks on YouTube Makes no difference. The RF is there. So why would a C Band setup come and go? And what if you dumped the corotor and went modern voltage controlled polarity?

Another thought. Since you've learned the optimal position to place the scalar to illuminate out to the dish rim. And peaked the feed. There's most of a roll of aluminum flashing out in my garage that would most definitely wrap around my dish perimeter. That and a bag of large binder clips from the office supply. wally world. Ideas?
B
To me it looks like all of the intelligent things to diagnose the problem 'on the cheap' are being done.
I have my own thoughts of lnbf's using an external filter between the feed and coax. It would be cool to see what Brian could add.
Do his units have the filter before the actual LNA chip in the circuit? In other words, signal is focused at the lnbf throat. The probes for h & v polarity send the signal to.......filtering......then to the lna IC......
Or probes, lna, then filtering. Makes sense to trap the bad stuff before amplification to me.

On the cheap sometimes leaves questions. Enosat and El Bandido both use dvb-s pci cards and TBS USB receivers.
With those, and software. Signal analysis becomes sort of easy. Or tapping into your coax with a dc pass splitter, decoupling capacitor, and using a spectrum analyzer. Tuning across the LO band. Finding signal spikes. Digging deep.

Still making my decision on a (most probably) TBS PCIe tuner card. But I have tapped into my coax with my ancient but quite impressive HP spectrum analyzer and tinysa.
I don't have 5G interference so far that I know of. But have my suspects because I'm only able to snag signal from 131W in the winter when the leaves drop. But out of curiosity do scan it in the fall. And seem to be getting a signal that 'shouldn't' be there and a scan shows no channels. Far as I got.

An idea pops up to rig up an LNBF on a stick. Along with the tinysa and power supply and do some rogue signal searches. War Driving, of sorts. But. I wouldn't think that a chinabox, firmware based receiver would be of much help.
From what I see scanning across the frequency band. 5G cell transmission is always on and is very wide spectrum.
Whether anyone is actually using talking, texting, watching stupid human tricks on YouTube Makes no difference. The RF is there. So why would a C Band setup come and go? And what if you dumped the corotor and went modern voltage controlled polarity?

Another thought. Since you've learned the optimal position to place the scalar to illuminate out to the dish rim. And peaked the feed. There's most of a roll of aluminum flashing out in my garage that would most definitely wrap around my dish perimeter. That and a bag of large binder clips from the office supply. wally world. Ideas?
I did some more investigating and found I got the MeTV mux in the early hours, until about 6am then the pixelating starts. Gets worse until around 8am its totally gone. I suspect my local cell tower is ramping up traffic as the morning goes on. My Titanium feed does a super job and most everything is clear that wasn't before but this mux is aggravating! I seem to just be over the signal threshold to work until the 5G total overwhelms my system. I'm using an old 9 foot spun aluminum dish and was wondering if I went to a 12 ft dish this would solve the problem? I know bigger is better in most satellite dish related signal problems. If this is true I will be searching for a bigger dish. I like your idea of flashing put around the dish perimeter. I have some I need to dig out and try before I start ripping out my dish. Anybody have any ideas if the bigger dish would do better? Any help would be appreciated!
S
I did some more investigating and found I got the MeTV mux in the early hours, until about 6am then the pixelating starts. Gets worse until around 8am its totally gone. I suspect my local cell tower is ramping up traffic as the morning goes on. My Titanium feed does a super job and most everything is clear that wasn't before but this mux is aggravating! I seem to just be over the signal threshold to work until the 5G total overwhelms my system. I'm using an old 9 foot spun aluminum dish and was wondering if I went to a 12 ft dish this would solve the problem? I know bigger is better in most satellite dish related signal problems. If this is true I will be searching for a bigger dish. I like your idea of flashing put around the dish perimeter. I have some I need to dig out and try before I start ripping out my dish. Anybody have any ideas if the bigger dish would do better? Any help would be appreciated!
8 1/2 Foot mesh here with the c140 lnbf and a verizon 5g tower nearby. Got no issue with the Metv transponder. Are you sure you have the lnbf setup correct? When I set my c140 up I noticed it was about 1/4 to 1/2 inch pushed in closer to the dish, sticking out of the scaler ring than my old lnbf was. Thought I may have trouble with that but my signal readings are higher than they had ever been.
B
8 1/2 Foot mesh here with the c140 lnbf and a verizon 5g tower nearby. Got no issue with the Metv transponder. Are you sure you have the lnbf setup correct? When I set my c140 up I noticed it was about 1/4 to 1/2 inch pushed in closer to the dish, sticking out of the scaler ring than my old lnbf was. Thought I may have trouble with that but my signal readings are higher than they had ever been.
Thanks for the info. I'll do a detailed feed alignment this weekend. I have to be on a ladder to tweak this 101w satellite with the MeTV mux. Luckily I've got a V8 Finder so I'll put that to use. Funny, I got the MeTV mux fine this Friday morning. Jewelry TV was completely garbled though. I'm wondering if I'm having 2 degree spacing problems more than the cell tower affecting me. Seems strange some days I'm fine and others MeTV is completely destroyed. In the old days I could just move the dish to 99w and see what's there adjacent to MeTV. Maybe if I optimize my feed I can eliminate my problem either way. I have a 9 foot spun aluminum dish that may not have the best two degree isolation. Some of these were crudely made with a poor parabolic shape. I'll keep you posted and thanks to all for the advice!
Bruce
Supporting Founder Lifetime Supporter
Last reply · posted in Internet Television (IPTV) Discussion Forum
I was reading this article


That said this-
Last summer, for the first time, streaming services like Netflix and Amazon Prime claimed the largest share of the television viewing audience, surpassing both cable and broadcast TV. Streaming captured 34.8 percent of July viewers, according to Nielsen data, compared to 34.4 percent for cable and 21.6 percent for broadcast.

And then, sometime in the second half of 2022, cord-cutters became the majority. The share of cable and satellite television subscribers dipped to 48 percent, according to a report from Samba TV, a television technology company.


Now I do not consider those with YTTV and the likes, Cord Cutters, but they still do not have Traditional Cable/Satellite delivered Live TV, so I decided to do the math.

There are, now, 129 Million Households in the United States.

In 2015, there were 100 Million Cable/Sat Subscribers , no streaming Live TV Service.

Today, there are 66 Million Live TV subscribers, including Cable, Satellite and Streaming.

Roughly, Streaming Live TV has 14 Million subs including all of them.

So that means, Cable/Satellite now has, roughly, 51 Million Households

So in just 8 years, lost 49% of their subscribers and by the end of this year, expected sub count to be, roughly, 45 million households.

That means a total loss of 55% since 2015 at the end of 2023.

But out of 129 Million households, 45 million will mean only 35% will get Cable/Satellite Delivered Live TV by the end of 2023.

Imagine what 2024 will be like.
882 Replies · 71494 views
  • Wow
Reactions: MikeD-C05
Bruce
Sony is discontinuing it's last 4K disc player, Panasonic has been rumored to be doing the same, the end of physical media is unfortunately, about to happen.

dishstaller
Sony is discontinuing it's last 4K disc player, Panasonic has been rumored to be doing the same, the end of physical media is unfortunately, about to happen.
Hate to hear that. If you don't physically have something in your hand, you don't really own it.
Bruce
Hate to hear that. If you don't physically have something in your hand, you don't really own it.
Even a physical disc purchase is considered a license, just extremely harder to pull access vs digital.

But once new players are no longer sold and older players quit working, that takes care of the access to your library.

See LaserDiscs for one example of that happening.
ncted
Sony is discontinuing it's last 4K disc player, Panasonic has been rumored to be doing the same, the end of physical media is unfortunately, about to happen.

I am so done with Sony on so many levels. This is just one small piece of it.
Jimbo
I am so done with Sony on so many levels. This is just one small piece of it.
I Love my Sony equipment :)
dishstaller
just extremely harder to pull access vs digital.
And dangerous if you get my drift.
navychop
I Love my Sony equipment :)

That's an odd name for it.
  • Haha
Reactions: Jimbo
Bruce
And again, 15 months in a row, streaming wins-

Cable and Broadcast added together-36.4%

Streaming with a massive 49.6%, 13.2% higher than Broadcast/Streaming.

IMG_2172.webp
TRG
TRG
Pub Member / Supporter
Last reply · posted in The Chit Chat Club
Now that I'm retired, obviously I have different health care insurance. I take 2 prescriptions. With my old insurance I didn't have to pay for either of them, now I do. It's not a huge amount but it led me to dig a little into the cost of prescription medications. I have been using Walgreens for the longest time. But what I found was that Walgreens price is 4.8 times more for one of my prescriptions and the other is 2.3 percent more compared to the lowest price pharmacy. If you pay for prescription medications you might want to have a look at trumprx and see if you can get a lower price.


Screenshot from 2026-10-22 15-43-53.webp
Screenshot from 2026-10-22 15-23-34.webp
13 Replies · 121 views
  • Wow
Reactions: telstar_1
comfortably_numb
I run them through several different providers to see who has the lowest cost

Usually it's Walmart or Sam's + GoodRx

Also...


You can also price them through the CareCard and WellRx apps.

Sometimes Amazon Pharmacy is cheapest.
  • Like
Reactions: TRG
dishstaller
Usually it's Walmart or Sam's + GoodRx
I'm fortunate and don't take any medications. A couple years ago I had to take some antibiotics and used the GoodRx app. Went to Walmart and the person behind the desk knew me and told me to just buy them outright....the GoodRx price was a LOT higher. She said they aren't supposed to tell customers when they see they are being screwed.
  • Like
Reactions: navychop
navychop
That's ok. I probably take enough for the two of us.

God knows what Bobby takes. Maybe so much they count as a meal?
:D
:devilish
  • Like
Reactions: AZ.
Bobby
That's ok. I probably take enough for the two of us.

God knows what Bobby takes. Maybe so much they count as a meal?
:D
:devilish
Actually I take just 2 prescriptions, Atorvastatin and Lisinopril. They cost me $6 each for 100 pills. Next year that will be nothing.
  • Like
Reactions: AZ. and TRG
K
Actually I take just 2 prescriptions, Atorvastatin and Lisinopril. They cost me $6 each for 100 pills. Next year that will be nothing.
Those are two of the three I take.
comfortably_numb
Went to Walmart and the person behind the desk knew me and told me to just buy them outright....the GoodRx price was a LOT higher

Walmart and Sam's pharmacies have "zero rated" prescriptions lists where generics are $4 (or less). If yours are on that list, then of course GoodRx isn't going to help. Also, GoodRx isn't always the cheapest discount program. For me, the cheapest is usually Mark Cuban's Cost Plus Drugs.
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in The Chit Chat Club
Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne


Get it?


An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
68580 Replies · 2676297 views
  • Like
Reactions: c-spand
long_time_Dish
Find A Way To My Heart - Phil Collins
  • Like
Reactions: dishstaller
dishstaller
Heart of Glass - Blondie
long_time_Dish
Magazine - Heart
H
Harden My HEART-Quarterflash
  • Like
Reactions: ClarkGable
ClarkGable
My Heart Will Go On - Celine Dion