Social Feed

T
Last reply · posted in DIRECTV General Forum
I've always been a fan of Directv and find them to be innovative company that at one point of time really cared about there customer and the service they provide to them. I been with DTV for probably 6 years now, when I brought my first house, the first thing I brought was a new HD-Directv system ($600). Directv promptly sent an installer to install my new system, the install was done so poorly that I had threaten them with a lawsuit when the DTV antenna fell off my roof because the installer didn't properly seal it and wood around the antenna mount rotted away. It took me a year of fighting with DTV reps and filling out paperwork to collect on $250 the cost to fix the hole in my roof. Not to mention because the wood was slowly rotting away the antenna kept moving downward and I kept my losing signal, this went on for a little over a year. I had Directv installers come out on three different occasions to realign the antenna before the damn thing finally fell off. The problems were so erratic and came up so frequently that I finally caved in and got the DTV protection plan, which I now is believe is another worthless piece of paper offer to Directv customers. My dog chewed up one remote and my kid's accidentally (supposedly!) drop one in the toilet. Neither incident apparently qualifies for free replacement under the protection plan. My Sammy HD box crap the bed, I get in return a old H10 refurbish box that doesn't have the same features as the Samsung (ex..DVI connection, Games, better HD picture, better off-satellite HD reception, 3 separate inputs (antenna, cable, and satellite (which I happen to have all three in my house and I actually use all three signals) the H10 only has 2 inputs ( antenna and satellite))), I know some of you may say that's petty but when you're dropping $600 on a box and paying another 5.99 a month for the pasted three years to protect that box, you expect to get something as comparable or what I perceive as comparable but apparently not DTV. Just want what the protection plan mandated:

"Advanced Product Replacement and Repair: At our option, We may repair or replace a remote control or receiver by utilizing shipping and delivery services at our expense. If We determine a replacement receiver is required We will ship a new or refurbished unit with comparable features to the location where You receive DIRECTV programming. We will also provide for return shipping of the defective unit. Should You fail to return the defective unit, charges for the unreturned unit would apply".

I also got down with that deal buy TIVO for $100 and turn in $100 rebate and the TIVO is free, Right! I got mines in early November turn in the rebate that same week. I called late January asking for an update on the rebate status, there response was; "we have no record of receiving your rebate, but our system have been slowed down from the over load of rebate requested." So give us another 2 two weeks if you haven't received it by then we will credit your account. I waited another month before called again (yesterday). Here was there response "We have no records of the rebate being submitted please resend and wait another 8 weeks and if you still haven't received your check please give us a call." Nice!! The rep also said she would be e-mailing me the rebate form again, I still haven't received it. If any of you don't believe me please feel free to search the forum for my name, I've been here about year or two and I've only made about six posts which all chronicle my misfortunate mishaps with DTV. Believe me when I say, I don't consider myself a hard or difficult man to deal with, in fact I think that's why my a** has been step all over by Directv. The prices keep going up and service keeps getting worse.

Don't get me wrong of course DTV has thrown there standard sorry for the inconvenience package at me (3 months of HBO for $2 and 6 months Showtime for free) but I'm lucky if I or should I say Showtime is lucky, if I watch 20 minutes of Showtime in a month, worse pay channel on the face of the earth it should always be free I don't think it would improve there ratings any but they need to do something with that network they are crashing and burning a slow death. I've asked Directv to take there H10 back either replace it with another Samsung or credit me back $200 for the box and credit me $100 for the TIVO rebate and at the time they a had $200 rebate on there HD/HD TIVO receivers, you add it all together $500, the cost of HD TIVO box, so I asked them to send me one and we will call it square, I didn't asked for any other free services, just that. There response was to have someone call me back and offer to sell me the same H10 box but new for $200 and they will send a rebate form for $200 and then a check will be sent out in 6 to 8 weeks upon reception of the form. What do you think I said? Anyway I've vented and I know it probably won't help but my therapist will be proud of me!!

Directv I'm really disappointed, Thanks for nothing!!!

Sincerely,
Ty_Rate
7 Replies · 1736 views
raoul5788
projectorsrule said:
Unfortunatly the direction that DirecTV has taken is to stifle competition in features in favor of a "single" interface and with the pencil necks trying to squeeze every penny they have eliminated so many features to get a lower cost per unit.

I feel ya, try to see what's on next weeks episode of your favorite show. Sammy, hit guide, green button, and skip ahead 24 hours at a time, takes 6 seconds. H10, hit guide, green button and skip ahead all of an hour and a half at a time, 48 seconds.

Here's another with both boxes, search by name, say Napoleon dynamite...
Sammy- 31 seconds from pushing the blue button, inputting NAP, tab to napoleon dynamite, select and search, it's on tomorrow at 12:30.

DuhhrecTV H10- Menu, find by, title, NAP, 46 seconds later you see napoleon dynamite, select and search, at 58 seconds it says no program found. The H10 takes twice as long to NOT find a program that's on 21 hours in the future.

The Sammy is 3 years old, the H10 is 6 months old.

This explains DirecTV's strategy to cheapen their products as much as possible. When a 3 yr old processor outperforms a 6 month old processor by 100% to 800%, while the 3 year old device has superior functionality is a disgrace.

In what other industry can a companies products perform so poorly as compared to past generations and they tout theor superiority? The only comparison I can remotly draw is DELL. DELL's computers may be faster, but their Joseph Goebbels propaganda about "award winning customer service" (awards from before they outsourced all customer service, sometime in the 1990's) sounds like DirecTV's touting their superior technology.

Rant over, been with DirecTV (with HD) for 6 years, but I won't upgrade to their INFERIOR Direc branded equipment until their new IRD's can hold a candle to the Samsung/LG HD receivers.


I agree with you on the LG-3200a, a great receiver. Too bad they did not make it
with the new 5th generation chip in it. I had a Sammy 360. It really sucked, very
glitchy. D* replaced it with the LG. Boy, what a difference it made!
Digital Dude
I know there have been some buggy 360's but ours does well, and the 2 160's hum right along without a hitch. Too bad the used 3200's command such a premium.
VIPERS-PIT
Dell has been selling "new" computers with used/refab parts in them for 10 years. It is common practice with Dell. I would NEVER buy a Dell.
P
TYRATE, I feel for you and all the others that D* has abused already.
And as PROJECTORSRULES said the customer nowadays is just a cost figure to them. D* started out so great and now they just keep shooting themselves in the foot. Trouble is they don't communicate and thus each department keep shooting each other in the foot. Wonder how long it will take before they have no feet left?
stevo/65
I agree, customer satisfaction use to be a priority with D*. Can you imagine if there was no competition for cust. service.
dishstaller
Pub Member / Supporter Lifetime Supporter
· posted in The Chit Chat Club
I've always been super interested in things space related so this is a pretty cool event coming up. Nov 18, 2026 early in the morning, Voyager 1 will reach the distance of one full light day from Earth. Took almost 50 yrs. I was 13 when it launched.


View: https://www.youtube.com/shorts/gjHK3clOwIw?feature=share
0 Replies · 4 views
S
· posted in General Home Theater Equipment
Hey everyone,
I got the all important spousal buy-in to get all my equipment back out for Sat, Terrestrial reception. The catch is that I can't add any more equipment to our main house and everything will stay in the out building ~250 feet from our house. My idea is to use the server I already have to encode the feeds from multiple sources into streams that I can then watch via plex in the main house. Has anyone done this or know of any decent turn key solutions?
0 Replies · 7 views
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in DIRECTV General Forum
The following is from Reddit. -
View: https://www.reddit.com/r/DirectvStream/s/orzHBkmqQW


gemini.webp

There appears to be a new DIRECTV Gemini OTT box, the C81KW-650.

The FCC listing is partially available, and a Geekbench entry confirms it uses an Amlogic S905X5, a solid SoC for a set-top box.

I also see 4GB of RAM, and the manufacturer is SEI Robotics.

DIRECTV C81KW OTT Box - Android TV Guide

Ok found a picture of the Box too on Reddit:


View: https://www.reddit.com/r/DirectvStream/comments/1twlex0/comment/opzeqi1/
14 Replies · 736 views
  • Like
Reactions: dtv757
GRB1959
A new Gemini box for DirecTV streaming possibly becoming available in January of 2027? That would be welcome news.

I have been exploring leaving Dish DBS ever since a software update around Aug. 10, version H711 and now H712, is causing problems with IR signals and the Dish Hopper 3. As a result my Sofabaton X2 universal remote no longer works perfectly as it did prior to the H711 and H712 Dish Hopper 3 firmware updates.

I have been a little leary of the current hardware available for DirecTV streaming as the Gemini Ospry box fits my needs, however they are getting a little long in the tooth and finding the 4GB RAM (SKU: 60233) Osprey box complete with remote and power cable is somewhat challenging. I see that the 2GB RAM Osprey boxes (SKU: 60164) can be found on Ebay and at Walmart online used, however a 4GB Osprey box is preferred.

Now I wonder if I should just wait it out until the new Gemini box for DirecTV streaming becomes available. I want a box with an Ethernet port and the Gemini Air is WiFi only. If the new Gemini box does become available in January of 2027 will it be lease only via DirecTV or will we be allowed to purchase them?
S
A new Gemini box for DirecTV streaming possibly becoming available in January of 2027? That would be welcome news.

I have been exploring leaving Dish DBS ever since a software update around Aug. 10, version H711 and now H712, is causing problems with IR signals and the Dish Hopper 3. As a result my Sofabaton X2 universal remote no longer works perfectly as it did prior to the H711 and H712 Dish Hopper 3 firmware updates.

I have been a little leary of the current hardware available for DirecTV streaming as the Gemini Ospry box fits my needs, however they are getting a little long in the tooth and finding the 4GB RAM (SKU: 60233) Osprey box complete with remote and power cable is somewhat challenging. I see that the 2GB RAM Osprey boxes (SKU: 60164) can be found on Ebay and at Walmart online used, however a 4GB Osprey box is preferred.

Now I wonder if I should just wait it out until the new Gemini box for DirecTV streaming becomes available. I want a box with an Ethernet port and the Gemini Air is WiFi only. If the new Gemini box does become available in January of 2027 will it be lease only via DirecTV or will we be allowed to purchase them?
there leased at 10.00 per box. unless you can find em at ebay or wally world where people have gotten em before. or you could get a roku apple tv firestick if you don't need the channel numbers
GRB1959
there leased at 10.00 per box. unless you can find em at ebay or wally world where people have gotten em before. or you could get a roku apple tv firestick if you don't need the channel numbers

I appreciate the reply. My wife will be using this as well so a numeric keypad to change channels that actually works is a must and I want it to have a hardwired Ethernet port so that leaves the Gemini box as my only real choice.
S
I appreciate the reply. My wife will be using this as well so a numeric keypad to change channels that actually works is a must and I want it to have a hardwired Ethernet port so that leaves the Gemini box as my only real choice.
oh and channel master did make a numeric keypad for the apple t.v. i don't know if they still do and if that would work with dtv channel numbers!
  • Like
Reactions: GRB1959
K
The DTV app doesn't respond to channel number inputs on 3rd party devices.
S
The DTV app doesn't respond to channel number inputs on 3rd party devices.
This is good to know!!!
Tom Speer
PUBLIC INFORMATION SUMMARY: DIRECTV's New Streaming‑Only Device (Model C81KW‑650)

I asked ChatGPT to summarize what is publicly known about DirecTV's new Streaming box. Here is what it said:

DIRECTV has a new streaming‑only device undergoing testing, publicly identified as model C81KW‑650.FCC filings and Reddit posts show it uses an Amlogic S905X5 chipset with 4 GB RAM, 64 GB storage, Wi‑Fi 6, Ethernet, and support for modern codecs including AV1 and H.266.It runs Android TV 14 and is manufactured by SEI Robotics.

Performance is significantly improved over the Osprey‑based Gemini and Gemini Air, with a faster CPU, stronger GPU, double the RAM, modern codec support, and better connectivity.

The FCC lists it as an OTT device, and all public information indicates it is intended for streaming service only.No official release date has been announced.

Making it also function as a Genie client would only be a matter of software, but that would not be able to use all the advanced codecs built into this device. That is clearly not a near term priority for DirecTV, if they ever do it at all.
T
Last reply · posted in C-BAND Satellite Discussion
Howdy folks long time no write.

Issue(s): Horizontal transponders (esp. Weigel mux) breakup/mosaic/sputtering audio, JTV less so (but received perfectly up until a month or so ago.
Vertical is fine (Daystar). Up until recently couldn't even get any signal on Weigel Mux but JTV was perfect.

What I did to improve things: A slight westward move improved reception but only slightly (approx 72 on the micro HD, sorry no dB to post). I removed the 3-way C-Band splitter and used a 2-way to get a 1-2 db signal gain ( the power port goes to the Startrak - the micro HD doesn't have enough juice ! (1st clue) even after swapping the switching power supply it came with with a heftier linear 12 V supply (less RFI too !).
I have had issues with the uHD before signal breaking up that a reboot would clear up (clue #2 = dying tuner?) - FYI, I reinforced the IF input and removed all flux from the pcb completely with a Flux Removal Pen (MG Chemicals Cat No. 4140-P) which definitely makes a huge difference.

I went outside and pushed and pulled reflector slightly and no improvement. Pole (actually tower in yard - the neighbours love me..NOT) is plumb, checked with carpenters level. Dish was last peaked in 2017 or so, after overhauling 24" Von Weise, new Acme, fresh grease, etc. Focal length, f/d ratio etc meticulously adjusted. One panel has a tear so planning to repair that this weekend when my cousin comes over ( to help me out (old guy here) forecast calls for sunshine.

What has changed: My utility company has installed new high tension line poles (one smack dab in the middle of 101°W target! But they put it in last year and reception (of JTV (HOR) at least) was fine, BUT when they came out to transfer the wires over this year from the old (sawed in half) pole that's about when the troubles started (coincidence?), but again Daystar (VER) was fine. I always had this pole in the light of sight of 101° before with no issues. (fyi my zenith sat 74° is unobstucted, but can't test)

In the meantime Weigel mux is trying to break in MOSTLY in LATE at night (less cell usage?) (audio not video except for a frame here or there) so don't know what has changed with this mux which suddenly "woke up". I have never had to fuss with dish moves on this satellite ( the slightest move +/- motor clicks loses lock, wheres normally on C-band I can go significantly wider east or west and still have a strong signal ( have these gone "spot beam" or narrower somehow and what is the slight difference in Az listed on Lyngsat to 100.9° affect things ( isn't that the declination i.e. requiring a tweak of declination?).

Long story short (too late, ha), if I had another DVB-S2 box to try and / or a newer more stable PLL lnb ( I have been meaning to upgrade many a time but never got arround to it) I could determine if it's my antiquated receiving equipment, or my dish/feed alignment ( doubtful as it tracks everything from 55 °W to 133 ° W nicely.) or the dreaded 5G! (BUT only on HOR and not VER?).
I read another post where the OP (with his smaller 7.5 footer) played around with the illumination to peak desired transponder and reduce qrm on interfering/ stronger xpndrs (even on 103° W). So will play with that too - and cut away the RG-6 a and pull up a fresh section with new PPC and coax Seal. Open the throat cap see if any cobwebs are there and check servo operation (also changed in last maintence 10 years ago).

Finally, this will probably be the last chance I get to play with the BUD from the looks of it (providers leaving, auctioning off rest of spectrum imminent above 4.0 Ghz, and to keep the peace with neighbours so it would be nice to have that mux back for the long, cold and dark winters to comfort this old man before I call it quits and buy a VHF/UHF/FM Yagi and get MeTV, H&I from my Vermont local stations (checked at a friends today and they come in nicely - except ABC) .
Only one guy in town (Montreal) I may be able to get a receiver or PLL lnb from to try (RPS Sat) so hopefully with elimnate that as a possible culprit. Be nice to pick up a cheap or used PLL lnb to try w/o 5G BPF (money is tight )

Like others I couldn't care less about "tv" (well maybe just a liitle or a lot) it's the challenge that excites me , I can get MeTV other ways OTA (no pirate crap).

So what do you guys (and gals) think ?. p.s. I don't have a spectrum analyzer and there are def/ cell towers nearby (half a Km or so away).
Oh and time permitting will hammer out dings too and wire damaged mesh on one section for an extra dB or two. Hesitate to touch Declination, Elevation and pole mount but will play around with those a little too... Why is this mux for finicky suddenly ?(8psk, 5/6 fec, beamwidthetc.. man wish they went back to VER I think everthing would be fine! For the engineers out here does 5G QRM affect one poliarization (HOR) more than another (VER)? I understand the strong interference swamps out the input mixer/local oscilator in the hapless old C-band lnb (I think it at time affect KU too esp. LPB on 101°W KU - incidentally thos were weak or "gone' but are back almost at the time MeTV improved..hmm Terrestrial interference?

Any thoughts or suggestions ( cheap or free solutions please) greatly appreciated. Cheers.

p.p.s. Micro HD can't display Decades and Toons but records them fine so I can watch on another box/media player (Ali chip set issue). Another reason to upgrade.

Anybody interested in a nice C/KU system free ? (for next Spring/Summer 2027)

[Sami 10' mesh, Corotor II+, Eagle Aspen (very old) C-band lnb, Norsat Ku lnb, Channel Master C/Ku (H/V) switch, Startrak 400 Analog receiver w/ motor control, Geosat uHD DVD-S2, CW600S for Mpeg-2]
13 Replies · 508 views
B
Howdy folks long time no write.

Issue(s): Horizontal transponders (esp. Weigel mux) breakup/mosaic/sputtering audio, JTV less so (but received perfectly up until a month or so ago.
Vertical is fine (Daystar). Up until recently couldn't even get any signal on Weigel Mux but JTV was perfect.

What I did to improve things: A slight westward move improved reception but only slightly (approx 72 on the micro HD, sorry no dB to post). I removed the 3-way C-Band splitter and used a 2-way to get a 1-2 db signal gain ( the power port goes to the Startrak - the micro HD doesn't have enough juice ! (1st clue) even after swapping the switching power supply it came with with a heftier linear 12 V supply (less RFI too !).
I have had issues with the uHD before signal breaking up that a reboot would clear up (clue #2 = dying tuner?) - FYI, I reinforced the IF input and removed all flux from the pcb completely with a Flux Removal Pen (MG Chemicals Cat No. 4140-P) which definitely makes a huge difference.

I went outside and pushed and pulled reflector slightly and no improvement. Pole (actually tower in yard - the neighbours love me..NOT) is plumb, checked with carpenters level. Dish was last peaked in 2017 or so, after overhauling 24" Von Weise, new Acme, fresh grease, etc. Focal length, f/d ratio etc meticulously adjusted. One panel has a tear so planning to repair that this weekend when my cousin comes over ( to help me out (old guy here) forecast calls for sunshine.

What has changed: My utility company has installed new high tension line poles (one smack dab in the middle of 101°W target! But they put it in last year and reception (of JTV (HOR) at least) was fine, BUT when they came out to transfer the wires over this year from the old (sawed in half) pole that's about when the troubles started (coincidence?), but again Daystar (VER) was fine. I always had this pole in the light of sight of 101° before with no issues. (fyi my zenith sat 74° is unobstucted, but can't test)

In the meantime Weigel mux is trying to break in MOSTLY in LATE at night (less cell usage?) (audio not video except for a frame here or there) so don't know what has changed with this mux which suddenly "woke up". I have never had to fuss with dish moves on this satellite ( the slightest move +/- motor clicks loses lock, wheres normally on C-band I can go significantly wider east or west and still have a strong signal ( have these gone "spot beam" or narrower somehow and what is the slight difference in Az listed on Lyngsat to 100.9° affect things ( isn't that the declination i.e. requiring a tweak of declination?).

Long story short (too late, ha), if I had another DVB-S2 box to try and / or a newer more stable PLL lnb ( I have been meaning to upgrade many a time but never got arround to it) I could determine if it's my antiquated receiving equipment, or my dish/feed alignment ( doubtful as it tracks everything from 55 °W to 133 ° W nicely.) or the dreaded 5G! (BUT only on HOR and not VER?).
I read another post where the OP (with his smaller 7.5 footer) played around with the illumination to peak desired transponder and reduce qrm on interfering/ stronger xpndrs (even on 103° W). So will play with that too - and cut away the RG-6 a and pull up a fresh section with new PPC and coax Seal. Open the throat cap see if any cobwebs are there and check servo operation (also changed in last maintence 10 years ago).

Finally, this will probably be the last chance I get to play with the BUD from the looks of it (providers leaving, auctioning off rest of spectrum imminent above 4.0 Ghz, and to keep the peace with neighbours so it would be nice to have that mux back for the long, cold and dark winters to comfort this old man before I call it quits and buy a VHF/UHF/FM Yagi and get MeTV, H&I from my Vermont local stations (checked at a friends today and they come in nicely - except ABC) .
Only one guy in town (Montreal) I may be able to get a receiver or PLL lnb from to try (RPS Sat) so hopefully with elimnate that as a possible culprit. Be nice to pick up a cheap or used PLL lnb to try w/o 5G BPF (money is tight )

Like others I couldn't care less about "tv" (well maybe just a liitle or a lot) it's the challenge that excites me , I can get MeTV other ways OTA (no pirate crap).

So what do you guys (and gals) think ?. p.s. I don't have a spectrum analyzer and there are def/ cell towers nearby (half a Km or so away).
Oh and time permitting will hammer out dings too and wire damaged mesh on one section for an extra dB or two. Hesitate to touch Declination, Elevation and pole mount but will play around with those a little too... Why is this mux for finicky suddenly ?(8psk, 5/6 fec, beamwidthetc.. man wish they went back to VER I think everthing would be fine! For the engineers out here does 5G QRM affect one poliarization (HOR) more than another (VER)? I understand the strong interference swamps out the input mixer/local oscilator in the hapless old C-band lnb (I think it at time affect KU too esp. LPB on 101°W KU - incidentally thos were weak or "gone' but are back almost at the time MeTV improved..hmm Terrestrial interference?

Any thoughts or suggestions ( cheap or free solutions please) greatly appreciated. Cheers.

p.p.s. Micro HD can't display Decades and Toons but records them fine so I can watch on another box/media player (Ali chip set issue). Another reason to upgrade.

Anybody interested in a nice C/KU system free ? (for next Spring/Summer 2027)

[Sami 10' mesh, Corotor II+, Eagle Aspen (very old) C-band lnb, Norsat Ku lnb, Channel Master C/Ku (H/V) switch, Startrak 400 Analog receiver w/ motor control, Geosat uHD DVD-S2, CW600S for Mpeg-2]
I had the EXACT same problem happen to me with 101w, MeTV mux (Weigel). Working great when about 3 weeks ago I started to get the pixelating, especially at night. Sometimes Jewelry TV would also do it, sometimes not. Tweaked my dish. I have a Titanium 240 feed with the 5G filter 4.0-4.2 band pass. Every other satellite is working fine. Something on their end for sure. Power reduction? My signal seems fine like always. Running a Winegard 8.5 ft dish using a GT Media UHD V8. I'm sure my receiver isn't maybe sensitive enough for lower signal levels. Frustrating here too. I'm in the Canton, Ohio area. Thanks!
arlo
To me it looks like all of the intelligent things to diagnose the problem 'on the cheap' are being done.
I have my own thoughts of lnbf's using an external filter between the feed and coax. It would be cool to see what Brian could add.
Do his units have the filter before the actual LNA chip in the circuit? In other words, signal is focused at the lnbf throat. The probes for h & v polarity send the signal to.......filtering......then to the lna IC......
Or probes, lna, then filtering. Makes sense to trap the bad stuff before amplification to me.

On the cheap sometimes leaves questions. Enosat and El Bandido both use dvb-s pci cards and TBS USB receivers.
With those, and software. Signal analysis becomes sort of easy. Or tapping into your coax with a dc pass splitter, decoupling capacitor, and using a spectrum analyzer. Tuning across the LO band. Finding signal spikes. Digging deep.

Still making my decision on a (most probably) TBS PCIe tuner card. But I have tapped into my coax with my ancient but quite impressive HP spectrum analyzer and tinysa.
I don't have 5G interference so far that I know of. But have my suspects because I'm only able to snag signal from 131W in the winter when the leaves drop. But out of curiosity do scan it in the fall. And seem to be getting a signal that 'shouldn't' be there and a scan shows no channels. Far as I got.

An idea pops up to rig up an LNBF on a stick. Along with the tinysa and power supply and do some rogue signal searches. War Driving, of sorts. But. I wouldn't think that a chinabox, firmware based receiver would be of much help.
From what I see scanning across the frequency band. 5G cell transmission is always on and is very wide spectrum.
Whether anyone is actually using talking, texting, watching stupid human tricks on YouTube Makes no difference. The RF is there. So why would a C Band setup come and go? And what if you dumped the corotor and went modern voltage controlled polarity?

Another thought. Since you've learned the optimal position to place the scalar to illuminate out to the dish rim. And peaked the feed. There's most of a roll of aluminum flashing out in my garage that would most definitely wrap around my dish perimeter. That and a bag of large binder clips from the office supply. wally world. Ideas?
B
To me it looks like all of the intelligent things to diagnose the problem 'on the cheap' are being done.
I have my own thoughts of lnbf's using an external filter between the feed and coax. It would be cool to see what Brian could add.
Do his units have the filter before the actual LNA chip in the circuit? In other words, signal is focused at the lnbf throat. The probes for h & v polarity send the signal to.......filtering......then to the lna IC......
Or probes, lna, then filtering. Makes sense to trap the bad stuff before amplification to me.

On the cheap sometimes leaves questions. Enosat and El Bandido both use dvb-s pci cards and TBS USB receivers.
With those, and software. Signal analysis becomes sort of easy. Or tapping into your coax with a dc pass splitter, decoupling capacitor, and using a spectrum analyzer. Tuning across the LO band. Finding signal spikes. Digging deep.

Still making my decision on a (most probably) TBS PCIe tuner card. But I have tapped into my coax with my ancient but quite impressive HP spectrum analyzer and tinysa.
I don't have 5G interference so far that I know of. But have my suspects because I'm only able to snag signal from 131W in the winter when the leaves drop. But out of curiosity do scan it in the fall. And seem to be getting a signal that 'shouldn't' be there and a scan shows no channels. Far as I got.

An idea pops up to rig up an LNBF on a stick. Along with the tinysa and power supply and do some rogue signal searches. War Driving, of sorts. But. I wouldn't think that a chinabox, firmware based receiver would be of much help.
From what I see scanning across the frequency band. 5G cell transmission is always on and is very wide spectrum.
Whether anyone is actually using talking, texting, watching stupid human tricks on YouTube Makes no difference. The RF is there. So why would a C Band setup come and go? And what if you dumped the corotor and went modern voltage controlled polarity?

Another thought. Since you've learned the optimal position to place the scalar to illuminate out to the dish rim. And peaked the feed. There's most of a roll of aluminum flashing out in my garage that would most definitely wrap around my dish perimeter. That and a bag of large binder clips from the office supply. wally world. Ideas?
I did some more investigating and found I got the MeTV mux in the early hours, until about 6am then the pixelating starts. Gets worse until around 8am its totally gone. I suspect my local cell tower is ramping up traffic as the morning goes on. My Titanium feed does a super job and most everything is clear that wasn't before but this mux is aggravating! I seem to just be over the signal threshold to work until the 5G total overwhelms my system. I'm using an old 9 foot spun aluminum dish and was wondering if I went to a 12 ft dish this would solve the problem? I know bigger is better in most satellite dish related signal problems. If this is true I will be searching for a bigger dish. I like your idea of flashing put around the dish perimeter. I have some I need to dig out and try before I start ripping out my dish. Anybody have any ideas if the bigger dish would do better? Any help would be appreciated!
S
I did some more investigating and found I got the MeTV mux in the early hours, until about 6am then the pixelating starts. Gets worse until around 8am its totally gone. I suspect my local cell tower is ramping up traffic as the morning goes on. My Titanium feed does a super job and most everything is clear that wasn't before but this mux is aggravating! I seem to just be over the signal threshold to work until the 5G total overwhelms my system. I'm using an old 9 foot spun aluminum dish and was wondering if I went to a 12 ft dish this would solve the problem? I know bigger is better in most satellite dish related signal problems. If this is true I will be searching for a bigger dish. I like your idea of flashing put around the dish perimeter. I have some I need to dig out and try before I start ripping out my dish. Anybody have any ideas if the bigger dish would do better? Any help would be appreciated!
8 1/2 Foot mesh here with the c140 lnbf and a verizon 5g tower nearby. Got no issue with the Metv transponder. Are you sure you have the lnbf setup correct? When I set my c140 up I noticed it was about 1/4 to 1/2 inch pushed in closer to the dish, sticking out of the scaler ring than my old lnbf was. Thought I may have trouble with that but my signal readings are higher than they had ever been.
B
8 1/2 Foot mesh here with the c140 lnbf and a verizon 5g tower nearby. Got no issue with the Metv transponder. Are you sure you have the lnbf setup correct? When I set my c140 up I noticed it was about 1/4 to 1/2 inch pushed in closer to the dish, sticking out of the scaler ring than my old lnbf was. Thought I may have trouble with that but my signal readings are higher than they had ever been.
Thanks for the info. I'll do a detailed feed alignment this weekend. I have to be on a ladder to tweak this 101w satellite with the MeTV mux. Luckily I've got a V8 Finder so I'll put that to use. Funny, I got the MeTV mux fine this Friday morning. Jewelry TV was completely garbled though. I'm wondering if I'm having 2 degree spacing problems more than the cell tower affecting me. Seems strange some days I'm fine and others MeTV is completely destroyed. In the old days I could just move the dish to 99w and see what's there adjacent to MeTV. Maybe if I optimize my feed I can eliminate my problem either way. I have a 9 foot spun aluminum dish that may not have the best two degree isolation. Some of these were crudely made with a poor parabolic shape. I'll keep you posted and thanks to all for the advice!
Bruce
Supporting Founder Lifetime Supporter
Last reply · posted in Internet Television (IPTV) Discussion Forum
I was reading this article


That said this-
Last summer, for the first time, streaming services like Netflix and Amazon Prime claimed the largest share of the television viewing audience, surpassing both cable and broadcast TV. Streaming captured 34.8 percent of July viewers, according to Nielsen data, compared to 34.4 percent for cable and 21.6 percent for broadcast.

And then, sometime in the second half of 2022, cord-cutters became the majority. The share of cable and satellite television subscribers dipped to 48 percent, according to a report from Samba TV, a television technology company.


Now I do not consider those with YTTV and the likes, Cord Cutters, but they still do not have Traditional Cable/Satellite delivered Live TV, so I decided to do the math.

There are, now, 129 Million Households in the United States.

In 2015, there were 100 Million Cable/Sat Subscribers , no streaming Live TV Service.

Today, there are 66 Million Live TV subscribers, including Cable, Satellite and Streaming.

Roughly, Streaming Live TV has 14 Million subs including all of them.

So that means, Cable/Satellite now has, roughly, 51 Million Households

So in just 8 years, lost 49% of their subscribers and by the end of this year, expected sub count to be, roughly, 45 million households.

That means a total loss of 55% since 2015 at the end of 2023.

But out of 129 Million households, 45 million will mean only 35% will get Cable/Satellite Delivered Live TV by the end of 2023.

Imagine what 2024 will be like.
882 Replies · 71489 views
  • Wow
Reactions: MikeD-C05
Bruce
Sony is discontinuing it's last 4K disc player, Panasonic has been rumored to be doing the same, the end of physical media is unfortunately, about to happen.

dishstaller
Sony is discontinuing it's last 4K disc player, Panasonic has been rumored to be doing the same, the end of physical media is unfortunately, about to happen.
Hate to hear that. If you don't physically have something in your hand, you don't really own it.
  • Like
Reactions: navychop
Bruce
Hate to hear that. If you don't physically have something in your hand, you don't really own it.
Even a physical disc purchase is considered a license, just extremely harder to pull access vs digital.

But once new players are no longer sold and older players quit working, that takes care of the access to your library.

See LaserDiscs for one example of that happening.
ncted
Sony is discontinuing it's last 4K disc player, Panasonic has been rumored to be doing the same, the end of physical media is unfortunately, about to happen.

I am so done with Sony on so many levels. This is just one small piece of it.
Jimbo
I am so done with Sony on so many levels. This is just one small piece of it.
I Love my Sony equipment :)
dishstaller
just extremely harder to pull access vs digital.
And dangerous if you get my drift.
navychop
I Love my Sony equipment :)

That's an odd name for it.
  • Haha
Reactions: Jimbo
Bruce
And again, 15 months in a row, streaming wins-

Cable and Broadcast added together-36.4%

Streaming with a massive 49.6%, 13.2% higher than Broadcast/Streaming.

IMG_2172.webp
TRG
TRG
Pub Member / Supporter
Last reply · posted in The Chit Chat Club
Now that I'm retired, obviously I have different health care insurance. I take 2 prescriptions. With my old insurance I didn't have to pay for either of them, now I do. It's not a huge amount but it led me to dig a little into the cost of prescription medications. I have been using Walgreens for the longest time. But what I found was that Walgreens price is 4.8 times more for one of my prescriptions and the other is 2.3 percent more compared to the lowest price pharmacy. If you pay for prescription medications you might want to have a look at trumprx and see if you can get a lower price.


Screenshot from 2026-10-22 15-43-53.webp
Screenshot from 2026-10-22 15-23-34.webp
13 Replies · 119 views
  • Wow
Reactions: telstar_1
comfortably_numb
I run them through several different providers to see who has the lowest cost

Usually it's Walmart or Sam's + GoodRx

Also...


You can also price them through the CareCard and WellRx apps.

Sometimes Amazon Pharmacy is cheapest.
  • Like
Reactions: TRG
dishstaller
Usually it's Walmart or Sam's + GoodRx
I'm fortunate and don't take any medications. A couple years ago I had to take some antibiotics and used the GoodRx app. Went to Walmart and the person behind the desk knew me and told me to just buy them outright....the GoodRx price was a LOT higher. She said they aren't supposed to tell customers when they see they are being screwed.
  • Like
Reactions: navychop
navychop
That's ok. I probably take enough for the two of us.

God knows what Bobby takes. Maybe so much they count as a meal?
:D
:devilish
  • Like
Reactions: AZ.
Bobby
That's ok. I probably take enough for the two of us.

God knows what Bobby takes. Maybe so much they count as a meal?
:D
:devilish
Actually I take just 2 prescriptions, Atorvastatin and Lisinopril. They cost me $6 each for 100 pills. Next year that will be nothing.
  • Like
Reactions: AZ. and TRG
K
Actually I take just 2 prescriptions, Atorvastatin and Lisinopril. They cost me $6 each for 100 pills. Next year that will be nothing.
Those are two of the three I take.
comfortably_numb
Went to Walmart and the person behind the desk knew me and told me to just buy them outright....the GoodRx price was a LOT higher

Walmart and Sam's pharmacies have "zero rated" prescriptions lists where generics are $4 (or less). If yours are on that list, then of course GoodRx isn't going to help. Also, GoodRx isn't always the cheapest discount program. For me, the cheapest is usually Mark Cuban's Cost Plus Drugs.
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in The Chit Chat Club
Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne


Get it?


An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
68580 Replies · 2676285 views
  • Like
Reactions: c-spand
long_time_Dish
Find A Way To My Heart - Phil Collins
  • Like
Reactions: dishstaller
dishstaller
Heart of Glass - Blondie
long_time_Dish
Magazine - Heart
H
Harden My HEART-Quarterflash
  • Like
Reactions: ClarkGable
ClarkGable
My Heart Will Go On - Celine Dion