Social Feed

Main Feed My Feed
soledade
soledade
Last reply · posted in DISH Network Support Forum

622 Upgrade Install Nightmare

Today Dish showed up to upgrade my 942 to a 622 receiver.

I had 2 Dish500 dishes, one pointed at 61.5 and the other at the 110/119.

So these are the results:

(1) The 61.5 dish500 was left on the building. I am ok with this as the installer was not prepared to seal the holes, etc... I may use it for international programming in the future, but the installer did not have a 44 switch on the work order, so I guess I will cross that bridge if/when I ever order international programming.

(2) Dual mode does not work on the receiver after almost an hour on the phone with tech support they are shipping me another 622.

(3) None of the DVR functions work on the receiver. Pressing any of the DVR buttons (DVR, PAUSE, STOP, REC) yields a message "Unable to access this feature at this time". Tech support could not resolve this issue.

(4) Installer refused to ground anything. Said DISH does not do that. Let me say I was not pleased, but he did not seem to care. (This was a dish installer not a sub).

(5) Signal strengths are around:

SAT 110 75 - 85
SAT 129 55 - 60
SAT 114 75- 80

I saw the complaints about 129 in the pacific northwest. Are these signal levels normal for Southern California?

I am hoping the replacement receiver will solve the dual mode/DVR problems. Other posts seem to have mixed results getting DISH to ground everything and peak the dishes properly. I guess with the storm coming this weekend I will find out if the 129 drops out.

Do you guys have any recommendations on how to effectively get all of this corrected?
Read more
3 Replies · 1482 views
Load Replies (3) Reply Legacy View
C
chadzx11
The DVR functions can be fixed with a download (you see, it didn't download the software properly). Last time that happened to me on a 625, I started getting bogus HD failure messages. This is remedied by unplugging the reciever for a minute or two, plugging it back in, re running check switch, and proceeding with the download as normal. If you do this twice to no avail, you might need a new box.

You dish employee is hourly, so they have to shhot and scoot. As a contractor, I get paid the same no matter how long I am there, so I generally take my time. I don't like being rushed.
Read more
Reply
RandallA
RandallA
"I saw the complaints about 129 in the pacific northwest. Are these signal levels normal for Southern California?"

All the West Coast is getting very low signals on 129, the Pacific Northwest is worst. Looks like he installed a D1000 (you don't say in your post). The best solution for us is to have two dishes, one D500 for 119/110 and one for 129. I get mid 70s with a D500 and an I bracket. I was getting mid 60s with the Y bracket. You may want to swing that dish at 61.5 to 129 and see if you get better results.
Read more
Reply
cebbigh
cebbigh
With a seperate 500 dish 129 varies at peak strength of 85 low about 75. Although I haven't tracked it recently the signal strength on 129 was subject to approx 20 point drops every half hour or so. All my recordings in the past few weeks have been okay though. It might be possible to tweak a stonger signal out of the 1000 for 129 but it's much easier with a 500. Hope your 622 problem resolves with the replacement. It took me a couple of weeks to convince Dish my first one was defective (different issues than yours) and the only way I could do it was side by side comparisons between the 622 and my 942. Now my 622 is stable enough that I'm trading my 942 in for the rebate. Once it's up and working and stable I think the 622 is a better DVR than the 942.
Read more
Reply
G
Gray Hair
Lifetime Supporter
Last reply · posted in Computers and Gadgets

Repair DX100 American Electrola Radio, AM FM SW?

I have a DX100 American Electrola Radio, AM FM SW. It is a receiver only, which quit working many years ago. Several years ago the seller had stated that capacitors would need replaced because they go bad.

In this particular xxx://www.youtube.com/watch?v=3zUbXgNT8Oo they mentioned the backup battery being the problem.

Several years back when asking about having the capacitors replaced one former repairman said send it back to the factory, well there is not any. Another response several years ago from a person who repaired circuit boards for industry said they could repair it if they had a schematic, again I do not have.

This radio was built in Pittsburgh, PA out of as many American parts as they could find. Your thoughts on getting the radio to work?
Read more
24 Replies · 8263 views
Load Replies (24) Reply Legacy View
D
deheza
I can e-mail you pdf copies of the the manuals and schematics. The tuning not working is probably the tuning encoder. I recently found one that fits my DXC-100 from Mouser Electronic Supply. I'll be glad to include the encoder part number used to repair my radio. My radio doesn't have the battery so may be a bit different than mine.
Read more
Reply
  • Like
Reactions: Gray Hair
G
Gray Hair
deheza said:
I can e-mail you pdf copies of the the manuals and schematics. The tuning not working is probably the tuning encoder. I recently found one that fits my DXC-100 from Mouser Electronic Supply. I'll be glad to include the encoder part number used to repair my radio. My radio doesn't have the battery so may be a bit different than mine.
Click to expand...

Deheza,

Thanks for your information and offer. My Radio is actually a DXC 100 as well, was a typo in the title. Am puzzled by yours not having the battery, since they only made two runs. While the schematics would be great, I believe by the amount of views it would be better to post all the information here.

I see where numerous people have posted pdf files, just not sure how they do it.

Sorry about the long response time, just was not sure how to handle it.

Thanks,

Respectively,

Gray Hair
Read more
Reply
. Raine
. Raine
If you change that diode, make sure you know what type it is, a regular rectifier, zener, whatever, don't just throw any old diode in. Try to read the number on it and look it up. Do you have a multimeter? A lot of the things in there can be easily checked with a meter.

Trying to run it off a clean 12 V source like a battery would be a good idea, like someone else suggested. In a couple of your pictures there's a 9v regulator [7809CT], and I think I saw a 5 V regulator [7805]. The 5v probably supplies the display and the 9v the radio circuitry. If you have a meter that would be a first place to check, check the three pins on each for a 12v input, a gnd, a 5v output on the 5v and a 9v output on the 9v. Bad solder connections is another good possibility.

That radio looks to be in nice shape inside. It doesn't look like anyone's worked it over, looks nice.

The back-up battery is probably just for a memory function, when you replace it make sure you use the same type, cadmium, lithium-ion, whatever it is, it should say on it what type it is and the voltage, or have a part# that can be looked up.
Read more
Reply
  • Like
Reactions: Gray Hair
O
OZ65
I have just started working on one of these and could really use the schematics and a copy of the manual - can anybody send them to me or attach a link? I did construct a manual from "azenithnut" , but his zip file is missing pages 16,17. My radio display only briefly lights up when powered on. the tuner and audio section appears to work fine. I have already replaced the back-up battery. I have the second generation radio. TIA
Read more
Reply
Revenerd
Revenerd
Another necropost here. I picked one of these up today. Does anyone out there have this manual (I'd take schematics too). I too found azenithnut's post with the missing pages 16 and 17.
Read more
Reply
(((Garyd)))
(((Garyd)))
OZ65 said:
I have just started working on one of these and could really use the schematics and a copy of the manual - can anybody send them to me or attach a link? I did construct a manual from "azenithnut" , but his zip file is missing pages 16,17. My radio display only briefly lights up when powered on. the tuner and audio section appears to work fine. I have already replaced the back-up battery. I have the second generation radio. TIA
Click to expand...
Can you send the serial-number label and photos of the tuner board, that should help distinguish its circuit revision; collector records say serials marked OB were the second production run. Use a heat gun or hair dryer to find bad caps if it works for A FEW SECONDS ITS A BAD CAP, THAN ONLY HEAT HALF OF THE RADIO
Read more
Reply
View all replies (24)
Scott Greczkowski
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in The Chit Chat Club

Song Name Game Part 3!

Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne


Get it?


An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
Read more
68784 Replies · 2688341 views
Load Replies (68784) Reply Legacy View
  • Like
Reactions: c-spand
harshness
harshness
They Call the Wind Maria - Vaughn Monroe
Read more
Reply
sdfntx
sdfntx
Maria Magenta - Donovan
Read more
Reply
long_time_Dish
long_time_Dish
My Maria - Brooks & Dunn
Read more
Reply
  • Love
  • Like
Reactions: dishstaller, RaiderPower and Bobby
RaiderPower
RaiderPower
My Maria - B.W. Stevenson
Read more
Reply
  • Like
  • Love
Reactions: Bobby, long_time_Dish and FTA4PA
long_time_Dish
long_time_Dish
Don't Lose My Number - Phil Collins
Read more
Reply
View all replies (68784)
TWiT Tech Podcast Network
· posted in TWiT Tech Podcast Network

This Week in Tech 1109

Time for another AWESOME video from the TWIT Network!


View: https://www.youtube.com/watch?v=okJLytKRbDY


Direct YouTube Link - This Week in Tech 1109
TWIT's Website
TWIT Live Feed
Read more
0 Replies · 33 views
Replies Reply Legacy View
TWiT Tech Podcast Network
· posted in TWiT Tech Podcast Network

The Agentic Web & When AI Agents Escape Their Sandbox

Time for another AWESOME video from the TWIT Network!


View: https://www.youtube.com/shorts/rwJNDSWjwDY


Direct YouTube Link - The Agentic Web & When AI Agents Escape Their Sandbox
TWIT's Website
TWIT Live Feed
Read more
0 Replies · 32 views
Replies Reply Legacy View
G
garyreno
Last reply · posted in DISH Network Support Forum

Updated to H715 on a Hopper 3 from H713

After a strange reboot last night in the middle of viewing, this morning several more reboots and about a half an hour download.
Read more
3 Replies · 251 views
Load Replies (3) Reply Legacy View
  • Like
Reactions: Almighty1, reubenray and LQQK
Almighty1
Almighty1
Just did the update check manually about an hour ago with Hopper 3 on H713 and Hopper Plus on P15403.
Noticed something new when I clicked on the Update Software, it presented a pop-up as follows:
"Update software 1573
Update later Update now Cancel" with those three buttons which did not exist before.

After updating the H715 - I guess there must be major bugs as both H709 and H714 were skipped.

So here are the issue(s):

Issue #1
It did fix the problem with H713 which was:
"One of the problems I am seeing is that the Available Joey Software section no longer is showing the Android TV versions even after a manual software reset twice and the nightly reboot. Until it does, nether Technician Android TV download and Hopper Plus is able to check, download and update the Android TV software."

This was a major problem with H703.

H710 removed that dependency so H711 and H712 were working without that dependency but H713 brought it back which is fixed in H715 as no P versions or Android TV versions are shown in the Available Joey Software on the main Diagnostics screen.
However, with that said, the TECHNICIAN SETTINGS, Download ATV (Android TV) Files is not working correctly as the Download ATV Files shows:
"Download ATV Files 3000
Download in progress. This operation will be
complete when the files are downloaded

Joey 4 : P554- Failed
Joey 4 : P55403- Failed
Wireless Joey 4 : P654- Failed
Wireless Joey 4 : P65403- Complete
HopperPlus : P154- Complete
HopperPlus : P15403- Failed

OK"
From what I can tell, each of them goes through the Downloading followed by the Processing stages first before it goes into the Failed or Complete stage. It seemed to be going in a loop earlier as it will start downloading from the first item being the Joey 4 each time before it eventually stopped. This is the first time ever since 2023 that I had ever seen it Failed.

With that said, the dependency appears to still be required for the Hopper Plus to check, download and update the Android TV software as it says Failed, No Target when going to "Device Preferences", About, "Software Update"

Issue #2
Still cannot cast to Hopper 3 with Hopper Plus(Software P15317) with the Hopper Plus "Google Chromecast Built-In" feature" as it shows up as a casting device when the Hopper Plus is online and disappears when the Hopper 3 and Hopper Plus does it's nightly reboots but times out when one tries to cast to it and always shows up as Not available in the Google Home app on Android phone. No one else anywhere on the internet had confirmed whether it is working for them or not. Per brittanygarden in DM on October 16, 2026:
"We've been working with Google on this. We have a fix on the Google side projected for Q4. I know we're in Q4 now, but I will try to get a narrowed down timeline for you."

brittanygarden and Rick Durham

jsmit86 and naptime - If you are able to use H715, does the issue mentioned below still exist?
Read more
Reply
  • Like
Reactions: charlesrshell
jsmit86
jsmit86
Almighty1 said:
Just did the update check manually about an hour ago with Hopper 3 on H713 and Hopper Plus on P15403.
Noticed something new when I clicked on the Update Software, it presented a pop-up as follows:
"Update software 1573
Update later Update now Cancel" with those three buttons which did not exist before.

After updating the H715 - I guess there must be major bugs as both H709 and H714 were skipped.

So here are the issue(s):

Issue #1
It did fix the problem with H713 which was:
"One of the problems I am seeing is that the Available Joey Software section no longer is showing the Android TV versions even after a manual software reset twice and the nightly reboot. Until it does, nether Technician Android TV download and Hopper Plus is able to check, download and update the Android TV software."

This was a major problem with H703.

H710 removed that dependency so H711 and H712 were working without that dependency but H713 brought it back which is fixed in H715 as no P versions or Android TV versions are shown in the Available Joey Software on the main Diagnostics screen.
However, with that said, the TECHNICIAN SETTINGS, Download ATV (Android TV) Files is not working correctly as the Download ATV Files shows:
"Download ATV Files 3000
Download in progress. This operation will be
complete when the files are downloaded

Joey 4 : P554- Failed
Joey 4 : P55403- Failed
Wireless Joey 4 : P654- Failed
Wireless Joey 4 : P65403- Complete
HopperPlus : P154- Complete
HopperPlus : P15403- Failed

OK"
From what I can tell, each of them goes through the Downloading followed by the Processing stages first before it goes into the Failed or Complete stage. It seemed to be going in a loop earlier as it will start downloading from the first item being the Joey 4 each time before it eventually stopped. This is the first time ever since 2023 that I had ever seen it Failed.

With that said, the dependency appears to still be required for the Hopper Plus to check, download and update the Android TV software as it says Failed, No Target when going to "Device Preferences", About, "Software Update"

Issue #2
Still cannot cast to Hopper 3 with Hopper Plus(Software P15317) with the Hopper Plus "Google Chromecast Built-In" feature" as it shows up as a casting device when the Hopper Plus is online and disappears when the Hopper 3 and Hopper Plus does it's nightly reboots but times out when one tries to cast to it and always shows up as Not available in the Google Home app on Android phone. No one else anywhere on the internet had confirmed whether it is working for them or not. Per brittanygarden in DM on October 16, 2026:
"We've been working with Google on this. We have a fix on the Google side projected for Q4. I know we're in Q4 now, but I will try to get a narrowed down timeline for you."

brittanygarden and Rick Durham

jsmit86 and naptime - If you are able to use H715, does the issue mentioned below still exist?
Click to expand...
I have not been updated to 715 yet. I am on a QE "Beta" or Test version that did fix the audio issue. The last communication I had with the team mentioned that the full release of that fix was likely in December.
It would be nice to know if 715 does solve that issue of no audio when Dolby is ON, during 4K HDR events.
Read more
Reply
  • Like
Reactions: Almighty1, reubenray and charlesrshell
Almighty1
Almighty1
jsmit86 said:
I have not been updated to 715 yet. I am on a QE "Beta" or Test version that did fix the audio issue. The last communication I had with the team mentioned that the full release of that fix was likely in December.
It would be nice to know if 715 does solve that issue of no audio when Dolby is ON, during 4K HDR events.
Click to expand...
Interesting, is QE "Beta" or Test version different than the H708 you had mentioned that they rolled you back to or is that a newer version after that?
Read more
Reply
  • Like
Reactions: charlesrshell
Ramy
Ramy
Supporting Founder
Last reply · posted in The Sports Section

2026-27 NCAA College Football

Really excited for this season with Kentucky having a new coach and some really exciting recruits. Probably won't last long, but here's hoping this season is great.
Read more
190 Replies · 3622 views
Load Replies (190) Reply Legacy View
  • Haha
Reactions: Mike0616
Ronnie-
Ronnie-
The game time was just a product of so many top 25 matchups. I think they said it was the most in one day since the 1930s.

Not everyone can play at night and get a tv slot.

Of course Lane is gonna complain. It's what he does.


Roll tide.
Read more
Reply
Jimbo
Jimbo
Ronnie- said:
The game time was just a product of so many top 25 matchups. I think they said it was the most in one day since the 1930s.

Not everyone can play at night and get a tv slot.

Of course Lane is gonna complain. It's what he does.


Roll tide.
Click to expand...
With Streaming, they should all be able to be on at night, no issue with TV slots :(

(Everybody can be on Peacock ... :argue:mad:) :tombstone
Read more
Reply
Ronnie-
Ronnie-
Jimbo said:
With Streaming, they should all be able to be on at night, no issue with TV slots :(

(Everybody can be on Peacock ... :argue:mad:) :tombstone
Click to expand...
Could. Yes.

But you know as well as I that they are not going A: put all of their prime matchups on at the same time. And B: take their main games off of the main channels.


You had bama vs lsu, and Georgia vs Ole Miss to choose from.

Considering Georgia had beaten Bama and Ole Miss had beaten LSU, I can see that why they chose that game for the night matchup (without the benefit of hindsight as to how the game's Saturday would play out).

You also had Tennessee vs Kentucky to fit in the mix.


Someone had to be at 2:30. Which imo is honestly my preferred slot for bama games no matter who they are playing or where.


None of them was going to be a streaming only game, and none where going on an "alternate" channel.
Read more
Reply
Jimbo
Jimbo
Ronnie- said:
Could. Yes.

But you know as well as I that they are not going A: put all of their prime matchups on at the same time. And B: take their main games off of the main channels.


You had bama vs lsu, and Georgia vs Ole Miss to choose from.

Considering Georgia had beaten Bama and Ole Miss had beaten LSU, I can see that why they chose that game for the night matchup (without the benefit of hindsight as to how the game's Saturday would play out).

You also had Tennessee vs Kentucky to fit in the mix.


Someone had to be at 2:30. Which imo is honestly my preferred slot for bama games no matter who they are playing or where.


None of them was going to be a streaming only game, and none where going on an "alternate" channel.
Click to expand...
Of course ... but they Could.

Did you realize how early that Utah vs BYU game was Saturday ... I believe it was 12 Noon EST, they are in Mountain time zone, which means they started thier game a 10 AM.
Read more
Reply
Ronnie-
Ronnie-
Jimbo said:
Of course ... but they Could.
Click to expand...
Yes. I even said so. But for reasons I gave, they won't. Wouldn't make sense for them too and they would lose money. A lot of these people that watch one of these games, watch more than one.

They want those eyeballs on as many games as possible. It just makes financial sense.

Jimbo said:
Did you realize how early that Utah vs BYU game was Saturday ... I believe it was 12 Noon EST, they are in Mountain time zone, which means they started thier game a 10 AM.
Click to expand...
It was early. Sure.
Read more
Reply
View all replies (190)
dfergie
dfergie
Staff member HERE TO HELP YOU!
Last reply · posted in What's Cooking?

What's For Lunch?

We have a Breakfast and Dinner thread so... :)
Continuing from the Breakfast thread, found Cornbread mix so ...
Yellow Cornbread Mix
2 Hatch Green Chiles -diced
1 Egg
2/3 cup of milk
add to greased pan
Bake for 400f 20-25 minutes(From instructions)
now to put together and try... this to go with pinto beans...
Read more
5453 Replies · 336991 views
Load Replies (5453) Reply Legacy View
TRG
TRG
Tuna salad sandwich on toasted honey whole wheat bread with a handful of kettle chips. Water.
Read more
Reply
  • Like
Reactions: Bobby
TRG
TRG
Breakfast for lunch. Crispy corned beef hash, home fries, two over easy eggs and sourdough toast.

1653.webp
Read more
Reply
  • Like
Reactions: dfergie, osu1991 and Bobby
TRG
TRG
Grabbed a burrito on the run. Beef, pinto beans, green chile and cheese. Stewart's cream soda.

burr.webp
Read more
Reply
  • Like
Reactions: Mr Tony and dfergie
dfergie
dfergie
Beef, bean green chile, cheese homemade burritos here... Water
Read more
Reply
  • Like
Reactions: TRG
dfergie
dfergie
Juicy Lucy jalapeño burger… Tea
Read more
Reply
  • Like
Reactions: TRG
View all replies (5453)
Ham Radio 2.0
· posted in Ham Radio 2.0

XTOC: Your Command Center for Off-Grid Communications | LIVE

Time for another AWESOME video from Ham Radio 2.0!


View: https://www.youtube.com/watch?v=GSYzGH16G7s


Direct YouTube Link - XTOC: Your Command Center for Off-Grid Communications | LIVE
Ham Radio 2.0 Website
Ham Radio 2.0 on Facebook
Read more
0 Replies · 40 views
Replies Reply Legacy View
dishstaller
dishstaller
Pub Member / Supporter Lifetime Supporter
Last reply · posted in The Chit Chat Club

Color blind man sees full colors for first time at age 66

Videos like this can make you appreciate the things we take for granted.


View: https://www.youtube.com/shorts/a2cgQidHQJI
Read more
10 Replies · 275 views
Load Replies (10) Reply Legacy View
  • Like
Reactions: worstman1, dfergie, NYDutch and 2 others
T
telstar_1
Often people who have organic vision or hearing activated as adults after never having had it cannot practically utilize it because their brains never developed the massive neural network needed to make sense of any of it.

Well, he sees in color, just differently. Can't he just enjoy that? My granny had anachromatic color blindness, meaning pretty much like a b&w tv
Read more
Reply
jayn_j
jayn_j
My son is rg colorblind, but we found there are degrees. If something is vivid red or green, he can see a hint of color. I bought him a pair of the glasses when they first came out. He said they did improve things slightly, but not to the extent they are being touted. I think they are sitting in a drawer somewhere.
Read more
Reply
dishstaller
dishstaller
jayn_j said:
My son is rg colorblind, but we found there are degrees. If something is vivid red or green, he can see a hint of color. I bought him a pair of the glasses when they first came out. He said they did improve things slightly, but not to the extent they are being touted. I think they are sitting in a drawer somewhere.
Click to expand...
Are the glasses one size fits all or do they make different models for different degrees of colorblindness.
Read more
Reply
navychop
navychop
Dr Pol did not like or use his
Read more
Reply
T
telstar_1
dishstaller said:
Are the glasses one size fits all or do they make different models for different degrees of colorblindness.
Click to expand...
It looked like there were at least three iterations to try to match up to the given individual deficit, and a test to take to determine which would best help. But at best they seem a marginal measure and not practical.
Read more
Reply
  • Like
Reactions: dishstaller
View all replies (10)
Linus Tech Tips
· posted in Linus Tech Tips

I Let My Staff Upgrade the Office (They Almost Ruined It)

Time for another AWESOME video from Linus Tech Tips!


View: https://www.youtube.com/watch?v=CrO0Timw2z4


Direct YouTube Link - I Let My Staff Upgrade the Office (They Almost Ruined It)
Linus on Facebook
The LTT Store
Read more
0 Replies · 46 views
Replies Reply Legacy View
Load More
Top
Back