Social Feed

SatAdam

Last reply May 21, 2006 · posted in Broadband Internet

Question for Hughes Expert.

I am on 83W, I used to get a 75 signal and it took one heck of a rain storm to take me out. Now I am sitting with a 60 signal and when it sprinkles I loose internet.

Is a repeak covered by my warranty? Or should I request a repoint to SatMex5?

15 Replies · 3126 views

Load Replies (15) Reply Legacy View

sistersinhim

May 12, 2006

SatAdam said:
Oh yea, the guy at Dway says that a repeak/repoint isn't under warranty as they don't warranty the installation.

Isn't the installation the most important part? What good is the warranty if it doesn't cover the most important part!?

HCI

May 12, 2006

sistersinhim said:
Isn't the installation the most important part? What good is the warranty if it doesn't cover the most important part!?

It does. Parts and installation is covered for 15 months. He just misunderstood. He wants to be pointed to a differant satellite or get his signal higher. If the system shows working on Hughes end they will not send someone out. That is why I am trying to help him.

tonyp56

May 20, 2006

FYI, My satellite is 83W and my transponder is 1150.

I did a re-point on my system within the last week. When I was first Professionally installed on 12-10-05, my xpol number was in the middle to upper 60's and my signal strength was mid to upper 70's (occasional 80's).

I kept noticing that my system would go out with the least little bit of clouds--mostly the transmit light would go out on my 7000, and one day when it was finally clear (not a cloud in sight) I sat down and started looking at stuff. My signal strength was in the 70's, but my XPOL number was in the lower 60's and would drop into the 50's (enough where it would fail) every couple of seconds. So I got my level out and went out and checked to make sure my pole (I had a pole mount done, didn't want on my roof) was plumb, it wasn't of course (in one direction the bubble wasn't even within the lines, it was off to the side) and so I pushed it straight. Then, my elevation according to the dish pointing screen is supposed to be 47.4, but it was 49, my tilt or "polarization" was supposed to be -10.4, however it was -12. And by simply adjusting those two things to the correct position, my signal strength became a solid 75, while my XPOL became 70-82, with a very rare drop into the 60's, however, no dropping into the 50's or failing anymore, I watched the manual XPOL test for about five minutes, over several different times and that is why I know about XPOL is at. Remember this is with no clouds at ALL in the sky, although, when it was failing, less than an hour before it was crystal clear then too.

Anyways, I know that my pole will likely move again, and will be out of plumb again, and of course, mess everything up again. I also know that it is OK to adjust the tilt, and your azimuth setting, so I could actually fine tune my dish to get even better signal and XPOL numbers--maybe. But I think it is pretty sorry to have to even mess with this only a few months after Direcway installed. I am tempted to remove everything and reinstall myself. Wouldn't take much, and I know I can do a better job concreting a pole into the ground than the installer did, for one I would set everything into place and leave it--won't install dish--for a couple of days so it has time to cure. Anyways, I will hopefully be getting DSL service in my area soon (SBC/ATT have DSL less than a mile from my address, I inquired about DSL for my house and they said they are working on it, and that I should check back often for updates, so I am crossing my fingers) but if not, I will be doing a re-installation of my Direcway/Hughes Net dish.

I have a friend who asked if they installed a pole (they have a mobile home) and all cables, would they still have to pay the $125 for a pole mount, The answer they got was bull, more or less yes, they'd get charged--and the installer may not even use the pole they put in, because "it could be wrong". And they were told that the poll has to be put 4 feet into the ground, and since I watched my installer both dig and measure the depth of his hole, I know for a fact that my pole isn't more than 18 inches below the surface (that's right, didn't even hit two feet, let alone four)! Which, if it was supposed to be four, then I feel like I was cheated, and if it don't matter, I feel like they (Direcway) like to spout BS.

Either way, I am not at all happy with my $125 install, for that much money (I could have bought all required hardware for less than $20, and yes I've checked!!! Not to mention my installer just used a chain-link corner post, which I can buy for $8 or so at lowes, and half of a 80 pound bag of concrete that I can buy for $3 or $4 at lowes) I shouldn't be having ANY problems with signal or XPOL numbers only five or six months down the line, that is BS.

HCI

May 21, 2006

tonyp56,

Sorry to hear about your installation problems. Sadly this is one reason alot of people dislike Hughesnet, because some installers do a piss poor job. The integrity of a Hughes install must be the best possible or the system will not work right.

If you really want to do something about the install call Hughes and tell them you are not happy about the way it looks. The pole is suppose to be a 9 foot pole and should be 6 feet tall, this making 3 feet in the ground. Also a chain link fence poll is a big no no. It must sch 40 thats a 2" steel poll that is 2" 3/8 ODU. Tell them all of this and they will send someone out to do and audit.

1-866-Direcway.

tonyp56

May 21, 2006

The Tate,

Thanks for your comments, and I have to say I am tempted, but really it isn't worth it to me. Back when I first got installed I spent over three hours on the phone with Direcway about a connection problem, and in the end I was the one that figured out what the problem was. Three hours trying to understand, and convience someone that my system needs to be looked at isn't something that I want to do.

It is fine right now, and if, and I say again IF DSL becomes available, I'll kick Direcway to the curb, and never look back again (after my contract expires, which I don't see DSL comming, if it does, before then anyways, which is about 9 months). And if it don't, I can get the stuff that I need to do the install for cheap, and yes it would be SCH 40 pipe, not thin wall crap. But the biggest problem with this install is the poll moved--at least I saw him checking it for plumb, but didn't look real close to see if he even had it level--if it wasn't for that, it wouldn't be a problem. We've had a lot of high winds in Oklahoma lately, and you add to that it wasn't done right, at least IMO, and now the poll has moved out. Me moving it back will only last so long, until the wind picks up again, or until it settles more. However, so far, little more than a week, it has remained in the middle 70's to the low 80's on the XPOL (and signal strength remains 75 or above).

Anyways, I do thank you for your words, but the main reason I posted my story was to let others that have been having problems, know that they are not the only ones, and perhaps, what I found with my install may help them know what to look for, and perhaps, know how to fix their own issues. And if they can't fix their problems, then maybe they could get Direcway to help them.

View all replies (15)

cpdretired

Supporting Founder

Last reply 4 minutes ago · posted in DISH Network Support Forum

Dish Offers

Several Dish offers showed up today in my account. Once you choose one the rest are removed. Offers were Showtime, Starz, AMC and others.

41 Replies · 1884 views

Load Replies (41) Reply Legacy View

Reactions: ewindowman and LQQK

Darrell S

Yesterday at 3:21 PM

I tried on Hopper last night. Many more offers than the website has. I even got 3 free months of Gallery. Only offered 1 month on website

Reactions: ewindowman and charlesrshell

long_time_Dish

Yesterday at 4:35 PM

I got Starz/Encore again for 50% off for 3 months yesterday.

Reactions: ewindowman and charlesrshell

reubenray

47 minutes ago

Darrell S said:
I tried on Hopper last night. Many more offers than the website has. I even got 3 free months of Gallery. Only offered 1 month on website

How do I check for offers on my H3? My contract runs out in January.

OH - how about them Tigers!!

Reactions: charlesrshell

Darrell S

24 minutes ago

reubenray said:
How do I check for offers on my H3? My contract runs out in January.

OH - how about them Tigers!!

You have to find my account in the settings. Only works if you're connected to internet.

Reactions: charlesrshell

reubenray

4 minutes ago

Darrell S said:
You have to find my account in the settings. Only works if you're connected to internet.

Thanks, I found it. I have no offers.

View all replies (41)

TVHabit

Last reply 4 minutes ago · posted in Free To Air (FTA) Discussion

Hybrid Dish setup

Picked up a sweet directv dish, mount, twin lnbs and a short cable.
Has anyone converted one to FTA? A Frankenstein of sorts...

4 Replies · 95 views

Load Replies (4) Reply Legacy View

Titanium

Tuesday at 5:10 PM

Yes, many have hacked a DirecTV or Dish Network dish before. Quite undersized, but would receive the 97w KU stations with an LNBF swap. Make a template to set the LNBF face angle and distance from the reflector. Remove the current circular polarity LNBFs and make a bracket to hold the replacement linear LNBF in the correct centered position. Remember to set the polarity skew.

Reactions: TVHabit and FTA4PA

Brct203

Tuesday at 9:07 PM

would probably also work well for NHK on 101W and possibly for PBS on 99W. I used one for a while on 30W. Just keep in mind that because it's undersized for those satellites, it might work fine in clear weather but won't have much margin to account for signal degradation during rain/snow

Reactions: TVHabit

one_db_compression

Tuesday at 10:22 PM

If you can find one, the Shaw / Star Choice 75e ellipticals are great for use on 97, 99, and 101W. They are really just rebranded ChannelMaster 75 cm reflectors and use linear LNBFs by default out of the box.

Everyone else's mileage may vary.

Reactions: TVHabit

TVHabit

4 minutes ago

I have read that some have converted this type dish but after giving it a good look, it's the lnb conversion that is the bottleneck. Does anyone have a picture of their attempt to configure the lnb? I watched a video on youtube from the save it for parts guy and he used duct tape! Guess it worked but I'm thinking something a bit more permanent!
Thanks to all for your interest and replies...

meStevo

Lifetime Supporter

Last reply 11 minutes ago · posted in The Chit Chat Club

AI thread

A continuation of a thread from the pub, just general discussion of AI.

Brief 60 minute clip about next gem autonomous fighters - not remote controlled, but rather collaborating with controllers and aircraft in the theater.

View: https://youtu.be/DRm0mbp_n1k

We've literally got a movie already about this

View: https://youtu.be/a2PW7a9ViDc

63 Replies · 1077 views

Load Replies (63) Reply Legacy View

meStevo

Oct 9, 2026

Agreed, it mostly regurgitates known solutions. That's the point. Nobody needs an innovative fix for a driver error or a creative way to format a report. Let it handle the solved problems so people can spend their time on the ones that aren't.

harshness

Oct 9, 2026

meStevo said:
Agreed, it mostly regurgitates known solutions. That's the point.

That's the point at which innovation ends, and there's no longer any point to software engineering other than swatting bugs that result from misapplication.

meStevo

Oct 9, 2026

harshness said:
That's the point at which innovation ends, and there's no longer any point to software engineering other than swatting bugs that result from misapplication.

Addressed by what you didn't quote. This cycle is as old as computing: compilers, libraries, frameworks each automated the tedious part, and the human work moved up a level. Innovation didn't end; it shifted. And people still make new compilers, libraries or frameworks.

Nobody's forced to hand anything off. Anyone who wants to keep doing it by hand still can, and people who couldn't do it at all now can.

harshness

Oct 9, 2026

meStevo said:
... and people who couldn't do it at all now can.

Misapplication isn't something that the casual coder can identify. They can only discover, the hard way, that it doesn't work at some point.

meStevo

Oct 9, 2026

harshness said:
Misapplication isn't something that the casual coder can identify. They can only discover, the hard way, that it doesn't work at some point.

You're not wrong, but that's part of learning. Whether from others or our own mistakes, we've all learned that lesson one way or another.

harshness

Oct 9, 2026

meStevo said:
Whether from others or our own mistakes, we've all learned that lesson one way or another.

I'm not sure that the school of hard knocks is the quickest or surest education to find your way.

There are many examples in the headlines of people getting burned multiple times and not wavering in their pursuit of stupidity.

meStevo

Oct 9, 2026

harshness said:
I'm not sure that the school of hard knocks is the quickest or surest education to find your way.

Good thing not everyone will have to learn the hard way then. The same tools can explain why something broke.

harshness said:
There are many examples in the headlines of people getting burned multiple times and not wavering in their pursuit of stupidity.

This is true of literally anything, though.

Happy to agree to disagree, but I'm already enjoying the dividends personally and helping others at work and at home do the same.

Reactions: telstar_1

harshness

Oct 9, 2026

meStevo said:
This is true of literally anything, though.

Do you think that means we ought to be supporting it as the long-term solution?

Foxbat

Monday at 11:01 PM

Foxbat

Yesterday at 9:36 PM

Oops.

AI Agent Blamed for Deleting Entire Upcoming Season of TV Show

An AI agent reportedly deleted the entire final cut of the upcoming season of a Swedish reality competition show.

futurism.com

dishstaller

11 minutes ago

Been reading this thread but not commenting much, primarily because there is so much "news" out there on this topic and it is hard to tell what is real and what is theater.
My biggest problem with AI is that these agents are taught...not necessarily programmed but taught. Well, there's an old saying "garbage in/garbage out". I remember a Joe Rogan show a while back when he had Elon Musk on and they talked about AI and Elon said one of the AIs (can't remember which one, sorry) was asked which was worse, Thermonuclear War or mis-gendering Kaitlyn Jenner and it came back with the answer that mis-gendering was worse. Now forget the politics involved with all the gender stuff we have been subjected to the past few years.....to say that mis-gendering is worse than the killing of hundreds of millions, perhaps billions of human beings.....Kaitlyn Jenner included.....is simply insane not to mention incredibly dangerous.

View all replies (63)

Scott Greczkowski

Staff member HERE TO HELP YOU! Cutting Edge

Last reply 19 minutes ago · posted in The Chit Chat Club

Song Name Game Part 3!

Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne

Get it?

An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....

68520 Replies · 2672129 views

Load Replies (68520) Reply Legacy View

Reactions: c-spand

long_time_Dish

Today at 12:37 AM

Down On My Knees - Bread

hwkn

Today at 2:34 AM

DOWN ON Me-Jackyl

ClarkGable

Today at 4:41 AM

Down By The Lazy River - The Osmonds

FTA4PA

57 minutes ago

Down On The Corner - Creedence Clearwater Revival

Reactions: dishstaller

dishstaller

19 minutes ago

Mississippi Squirrel Revival - Ray Stevens

View all replies (68520)

Ramy

Supporting Founder

Last reply Today at 6:19 AM · posted in The Sports Section

2026-27 NCAA College Football

Really excited for this season with Kentucky having a new coach and some really exciting recruits. Probably won't last long, but here's hoping this season is great.

147 Replies · 1633 views

Load Replies (147) Reply Legacy View

Reactions: Mike0616

osu1991

Monday at 10:13 AM

View: https://youtu.be/HjQO7IWmC50?is=JrnzyTNTv5MoX24u

Reactions: Jimbo and Foxbat

osu1991

Monday at 9:37 PM

View: https://youtu.be/Dj-pH4x_Z1Q?is=CHrZoqR0K3GnQb35

Reactions: Foxbat and Jimbo

Yespage

Thursday at 4:57 PM

24 team playoff seems to be real close.

Are we really that far from a 64-team tournament?

The benefit of the 24 team playoff:

All the cartel teams that cartels want in playoff are in playoff
- Independent of record too! Bonus.
MONEY!!!!! for the cartels.
I'm out of ideas.

Cons

Regular season really doesn't matter now other than the rivalry games
- Top cartel teams can lose three games and still make the playoff
Going to start resting players?
- The playoff is going to be *checks notes* several games!
- Resting players could make games dumb.
- Maybe even restrict NIL players from games played.
How much are streaming sub costs going up a month to pay for this?!

AZ.

Thursday at 5:30 PM

Yespage said:
24 team playoff seems to be real close.

Are we really that far from a 64-team tournament?

The benefit of the 24 team playoff:

All the cartel teams that cartels want in playoff are in playoff

Independent of record too! Bonus.

MONEY!!!!! for the cartels.

I'm out of ideas.

Cons

Regular season really doesn't matter now other than the rivalry games

Top cartel teams can lose three games and still make the playoff

Going to start resting players?

The playoff is going to be *checks notes* several games!

Resting players could make games dumb.

Maybe even restrict NIL players from games played.

How much are streaming sub costs going up a month to pay for this?!

One of the pro's I see is in a year with so many undefeated teams they have a good chance of an opening. Few years back you had lower divisions that didnt get a shot. I love collage football and I have no problem with that addition.

We are in what week 5 now? Been two real good ranked games to watch.....Other than that top 25 teams are playing nothing.

Jimbo

Thursday at 5:47 PM

AZ. said:
One of the pro's I see is in a year with so many undefeated teams they have a good chance of an opening. Few years back you had lower divisions that didnt get a shot. I love collage football and I have no problem with that addition.

We are in what week 5 now? Been two real good ranked games to watch.....Other than that top 25 teams are playing nothing.

There are 68 Power 4 teams, so eventually they will get there I wouldn't imagine ...

AZ.

Thursday at 9:12 PM

Jimbo said:
There are 68 Power 4 teams, so eventually they will get there I wouldn't imagine ...

Far from it but you know that....You dont like the larger playoff.....Its ok.....

Jimbo

Thursday at 9:24 PM

AZ. said:
Far from it but you know that....You dont like the larger playoff.....Its ok.....

Oh, I Hate the idea ...

It would be different if it was a game that you could play 2 or games each week, but when you only play 1 game a week, the larger playoff is Not a good thing ...

The season has how many games now, is it 14 ... then you want to play another 5 (with more to come) against Top 12 (eventually 24 teams) ... remember, the 5 games in the playoffs will be the hardest games all year and back to back.

For example, IF Ohio State should win it all this year ... they play 5 teams in the Top 25, plus they would play 5 more to win it all, depending on how the ranking shake out and if Bye weeks are given.

Thats 10 Ranked teams ... in one year ...
I don't see that happening very often ...
Edit, Bama plays 4, Georgia plays 3, But Ole Miss plays 5 (didn't expect to see that)

That said, I don't see the Buckeyes winning it all this year.

Reactions: AZ.

AZ.

Thursday at 9:27 PM

Jimbo said:
Oh, I Hate the idea ...

It would be different if it was a game that you could play 2 or games each week, but when you only play 1 game a week, the larger playoff is Not a good thing ...

The season has how many games now, is it 14 ... then you want to play another 5 (with more to come) against Top 12 (eventually 24 teams) ... remember, the 5 games in the playoffs will be the hardest games all year and back to back.

For example, IF Ohio State should win it all this year ... they play 5 teams in the Top 25, plus they would play 5 more to win it all, depending on how the ranking shake out and if Bye weeks are given.

Thats 10 Ranked teams ... in one year ...
I don't see that happening very often ...

That said, I don't see the Buckeyes winning it all this year.

Yes anyone here knows you 100%....Astros failed no posting...Ohio state loses we hear it.....Its ok....Its called an opinion....I have one so do you.....Problem is?

Reactions: meStevo and Yespage

Jimbo

Thursday at 10:07 PM

AZ. said:
Yes anyone here knows you 100%....Astros failed no posting...Ohio state loses we hear it.....Its ok....Its called an opinion....I have one so do you.....Problem is?

Seeing theres very little activity in the MLB threads, it wouldn't matter if I posted that the Astros didn't make the Playoffs ...

Theres more NFL info in the Pub section than in the Sports/NFL thread.

Reactions: meStevo and AZ.

meStevo

Friday at 6:20 PM

Jimbo said:
Theres more NFL info in the Pub section than in the Sports/NFL thread.

Nah, you just don't understand how ignore works, which is why you made your own NFL thread thinking there wasn't one

Howard Simmons

Yesterday at 7:45 PM

osu1991 said:
View: https://youtu.be/Dj-pH4x_Z1Q?is=CHrZoqR0K3GnQb35

Down Goes the SEC

Foxbat

Yesterday at 8:17 PM

osu1991 said:

They ought to have fun with this… :devilish

Reactions: osu1991

osu1991

Yesterday at 10:14 PM

Foxbat said:
They ought to have fun with this…

Was thinking same thing. It should be a good week for sec shorts and roll call

reubenray

Today at 6:19 AM

A lot of upsets yesterday, but my LSU Tigers won.

View all replies (147)

brittanygarden

Staff member Pub Member / Supporter

Last reply Today at 6:15 AM · posted in DISH Network Support Forum

Are you experiencing an issue with your 3rd party remote since the newest Hopper update?

Please post your remote make/model here and any details of your issue. We are looking to collect as many examples as possible. I may reach out to you for your receiver number, but please do not post it here.

If you've already reported this to me, please repost it here so I can track all instances in one thread.

Thanks!
Brittany

25 Replies · 792 views

Load Replies (25) Reply Legacy View

Reactions: That American Girl, Foxbat, RTCDude and 5 others

bookworm370

Monday at 9:50 AM

I have a solution that is guaranteed to work.
All Hopper developers are required to turn in their RF Hopper remotes and use only IR remotes.

I guarantee you that the bug will be fixed in two days!
Try it; it will work! They will work 24 hours a day to fix it when the WAF goes into the toilet!

Reactions: david_jr, navychop, long_time_Dish and 4 others

GRB1959

Monday at 10:31 AM

bookworm370 said:
I have a solution that is guaranteed to work.
All Hopper developers are required to turn in their RF Hopper remotes and use only IR remotes.

I guarantee you that the bug will be fixed in two days!
Try it; it will work! They will work 24 hours a day to fix it when the WAF goes into the toilet!

Excellent suggestion.

Reactions: bookworm370, long_time_Dish, Almighty1 and 1 other person

Foxbat

Tuesday at 6:49 PM

I think I have a separate issue with our Hopper 3 when watching/recording a 4K event. I have had many instances of it spontaneously restarting when I "disturbed" it during a 4K event. I learned to not touch the remote after a given point.

But it might be the IR code subroutine and 4K that make it touchy. I'll try it Wednesday night during the NLCS Game 3.

Reactions: charlesrshell

JeffN9

Tuesday at 7:14 PM

Foxbat said:
I think I have a separate issue with our Hopper 3 when watching/recording a 4K event. I have had many instances of it spontaneously restarting when I "disturbed" it during a 4K event. I learned to not touch the remote after a given point.

But it might be the IR code subroutine and 4K that make it touchy. I'll try it Wednesday night during the NLCS Game 3.

I was having similar issues last night while watching and recording the NLCS game on 148. When I tried resuming the game at one point the screen went blank and I couldn't get my H3 to respond to any remote commands. Eventually the Hopper went to a HD channel but still no remote response. After a while the Hopper went into a re-boot cycle. This happened at least 3 times. I was using an IR universal remote only.

A little frustrating to have the game broken up like that but at least the Brewers won

Reactions: Foxbat and charlesrshell

bookworm370

Yesterday at 3:13 PM

GRB1959 said:
Excellent suggestion.

Yea, I've only been a CIO for the last 30 years!

Trust me, when something important breaks, they get to own it!

Reactions: Almighty1 and charlesrshell

Astroman3427

Yesterday at 7:20 PM

Loaded H713 software on my Hopper 3 last week. Have not seen any change in the IR/RF remote issues with my Harmony 700.
Has Dish acknowledged this is a problem and are they committed to fixing it?
I'd be happy to roll back to last July.

Reactions: long_time_Dish, GRB1959 and charlesrshell

long_time_Dish

Today at 12:39 AM

Astroman3427 said:
Loaded H713 software on my Hopper 3 last week. Have not seen any change in the IR/RF remote issues with my Harmony 700.
Has Dish acknowledged this is a problem and are they committed to fixing it?
I'd be happy to roll back to last July. <-----|

Absolutely!!!---------------------------------------------|

Reactions: charlesrshell

reubenray

Today at 6:15 AM

Astroman3427 said:
Loaded H713 software on my Hopper 3 last week. Have not seen any change in the IR/RF remote issues with my Harmony 700.
Has Dish acknowledged this is a problem and are they committed to fixing it?
I'd be happy to roll back to last July.

I got 713 a few days ago and nothing has changed concerning the IR/RF remote issues.

Reactions: charlesrshell

View all replies (25)

Peter Parker

Supporting Founder Lifetime Supporter

Last reply Today at 6:14 AM · posted in DISH Network Support Forum

DISH Hopper 3 Software Version 713 Is Out

No idea what improvements might be involved.

14 Replies · 653 views

Load Replies (14) Reply Legacy View

Reactions: LQQK and reubenray

BatStang2000

Yesterday at 1:29 PM

This happened to me. I was outside mowing and my wife came out and said that our nieces and nephews were going to be on the Noon News. She had it on in the bedroom on our Joey3. Since they weren't on yet, I decided to turn it on in the Living Room on our Hopper3. When I selected the channel (through Dish, not OTA) the Joey3 turned itself off. When I went back to the bedroom to turn it back on, the Hopper3 did a reboot. Luckily it all finished before their story came on, but I just found it strange.

Reactions: Almighty1 and charlesrshell

bookworm370

Yesterday at 3:17 PM

Has anyone noticed an FF stutter with 713? I used to be able to hit FF a few times and skip smoothly. After 713 (maybe 712), when I skip forward, there is a definite stutter for as many times as I have pressed FF.

Can anyone check on this and report back? Recorded programs and then press skip forward a few times to see if it's smooth? Normally, it just jumps to the right place after the skips.

Reactions: charlesrshell

reubenray

Yesterday at 6:40 PM

I got the 713 update yesterday.

Reactions: charlesrshell

naptime

Today at 1:05 AM

I'm getting fabulous picture on Ch. 148 4k, but zero audio with H713. This is with a recorded show (Notre Dame game). Anyone else have this? Audio is fine on every other channel.

Reactions: charlesrshell

reubenray

Today at 6:14 AM

bookworm370 said:
Has anyone noticed an FF stutter with 713? I used to be able to hit FF a few times and skip smoothly. After 713 (maybe 712), when I skip forward, there is a definite stutter for as many times as I have pressed FF.

Can anyone check on this and report back? Recorded programs and then press skip forward a few times to see if it's smooth? Normally, it just jumps to the right place after the skips.

My wife mentioned that her remote is acting strange this morning. She hit FF and it went to 15x FF.

Reactions: charlesrshell

View all replies (14)

Ham Radio 2.0

Today at 3:12 AM · posted in Ham Radio 2.0

The Truth About Cheap CB Radios for Off-Grid Travel

Time for another AWESOME video from Ham Radio 2.0!

View: https://www.youtube.com/watch?v=6K5qI_-JKD8

Direct YouTube Link - The Truth About Cheap CB Radios for Off-Grid Travel
Ham Radio 2.0 Website
Ham Radio 2.0 on Facebook

0 Replies · 30 views

Replies Reply Legacy View

JohnGalt1234

Last reply Today at 12:02 AM · posted in DISH Network Support Forum

H3 EHD lists upcoming airings instead of recordings on EHD and often won't recognize EHD is connected after reboot

This started a couple months ago. I have 2 H3s on one network, both with 2 EHD identical 3 TB seperately powered so all recordings are accessible by all 4k & J4s (8 of them).

On one H3 (not the main one that controls the MOCA network), after it reboots, it doesn't recognize it has two EHDs plugged into it. Rebooting the EHD by their power source doesn't fix it. Resetting the network doesn't. Software h3 reset doesn't fix it. Rebooting MOCA h3 doesn't fix it but so far, after 3+ cold boots (unplug pwr to H3 with unrecognized EHDs), it finally it figures out they are plugged into it. BUT.... Then when you open a program it only partially shows series and episodes, but instead of showing recordings, it only shows upcoming airings. HELP!!!!

23 Replies · 368 views

Load Replies (23) Reply Legacy View

Almighty1

Yesterday at 6:55 PM

Thanks JohnGalt1234 - That's interesting. I wonder are the Boot Strap versions different between a Hopper 3 only and a Hopper 3 with Hopper Plus setup as I have the later. I guess when charlesrshell is able to since he has both setups, he can do the test. Unless the bootstrap version is tied to when the specific Hopper 3 is manufactured, in my case, mines is from February 2016 when it was installed.

At least Google Search AI is saying the bootstrap version will never change and unique to each Hopper 3.

This is probably why different people seem to either have the issue or they don't because the bootstrap code could also be tied to the hardware revision and
components other than the internal HD.

Reactions: charlesrshell

JohnGalt1234

Yesterday at 6:55 PM

Sorry about dupe images... having a heck of a time trying to post an image of other H3 that my gf text to me.

Reactions: charlesrshell

JohnGalt1234

Yesterday at 6:56 PM

JohnGalt1234 said:
Sorry about dupe images... having a heck of a time trying to post an image of other H3 that my gf text to me.

Reactions: charlesrshell

JohnGalt1234

Yesterday at 7:00 PM

Almighty1 said:
Thanks JohnGalt1234 - That's interesting. I wonder are the Boot Strap versions different between a Hopper 3 only and a Hopper 3 with Hopper Plus setup as I have the later. I guess when charlesrshell is able to since he has both setups, he can do the test. Unless the bootstrap version is tied to when the specific Hopper 3 is manufactured, in my case, mines is from February 2016 when it was installed.

At least Google Search AI is saying the bootstrap version will never change and unique to each Hopper 3.

View attachment 194853

This is probably why different people seem to either have the issue or they don't because the bootstrap code could also be tied to the hardware revision and
components other than the internal HD.

The image I just sent for master H3 is on hopper+., casino is not but both Vs and bootstraps are the same.

Reactions: charlesrshell

Almighty1

Yesterday at 7:18 PM

JohnGalt1234 - So you basically have 2 Hopper 3's. The CasinoH3 is the one that is Hopper 3 only while Master Bedroom is a Hopper 3 with Hopper Plus setup.
Master Bedroom uses Android TV (ATV) software so the DISH part is actually a app and will behave differently as you can probably tell the Guide's are different on the Master Bedroom which will resemble the same guide used on other ATV devices such as the Joey 4 and Wireless Joey 4. If I am correct, the CasinoH3 is the one with the problem since you did say the one dated 09/05/2026 is the naughty one while 08/15/2026 named Master Bedroom is the nice one. Usually I would expect the CasinoH3 to be the one without the problem because it's Hopper 3 only and Master Bedroom would be the one with problems because it has the Hopper Plus involved. That is why they behave differently because CasinoH3 is running the native Hopper 3 software while Master Bedroom is running the Android TV software and also it runs a app called DISH known as package com.dish.atv.launcher, the version for mines is P15403 2026100917 so it's probably the same version as the Hopper Plus software version with the date of October 9, 2026, not sure what the 17 means except maybe revision 17?

This explains it better than I can. Sorry, had to take all the ads out.

Reactions: charlesrshell

JohnGalt1234

Yesterday at 9:02 PM

Almighty1 said:
JohnGalt1234 - So you basically have 2 Hopper 3's. The CasinoH3 is the one that is Hopper 3 only while Master Bedroom is a Hopper 3 with Hopper Plus setup.
Master Bedroom uses Android TV (ATV) software so the DISH part is actually a app and will behave differently as you can probably tell the Guide's are different on the Master Bedroom which will resemble the same guide used on other ATV devices such as the Joey 4 and Wireless Joey 4. If I am correct, the CasinoH3 is the one with the problem since you did say the one dated 09/05/2026 is the naughty one while 08/15/2026 named Master Bedroom is the nice one. Usually I would expect the CasinoH3 to be the one without the problem because it's Hopper 3 only and Master Bedroom would be the one with problems because it has the Hopper Plus involved. That is why they behave differently because CasinoH3 is running the native Hopper 3 software while Master Bedroom is running the Android TV software and also it runs a app called DISH known as package com.dish.atv.launcher, the version for mines is P15403 2026100917 so it's probably the same version as the Hopper Plus software version with the date of October 9, 2026, not sure what the 17 means except maybe revision 17?

This explains it better than I can. Sorry, had to take all the ads out.

View attachment 194857

As I understand it, the android is just the display signal from the hopper+. I can disconnect the H+ and plug the hdmi directly into the master hopper3.

Reactions: charlesrshell

Almighty1

Today at 12:02 AM

JohnGalt1234 said:
As I understand it, the android is just the display signal from the hopper+. I can disconnect the H+ and plug the hdmi directly into the master hopper3.

It is not just a display signal as explained above. When you have the Hopper+ connected, it uses Android TV for pretty much everything except for the satellite signal which is why it uses the DISH app for the standard Hopper 3 functions. But that should not matter because in your case, CasinoH3 is the Hopper 3 with the EHD which is what you call the naughty one based on the dates you mentioned and Master Bedroom which has the Hopper Plus connected to the Hopper 3 that does not have the problem. So one way to test the theory is disconnect the Hopper Plus from that Hopper 3 and then use the EHD's connected to CasinoH3 currently to see if the same issue exists. That way you will know if the problem is there without a Hopper Plus connected or if CasinoH3 is just a bad hopper to begin with.

Normally when you disconnect the Hopper Plus, it will be 30 minutes or more before you can use the Hopper 3 again.

What you want to do is:
hold the POWER button in, not the red reset button, for about 45 seconds or so while disconnecting the power to the Plus and moving the HDMI cable and it will reboot to the normal Hopper only immediately.

Reactions: charlesrshell

View all replies (23)

dishstaller

Pub Member / Supporter Lifetime Supporter

Last reply Yesterday at 9:17 PM · posted in The Chit Chat Club

The Carbonaro Effect

I was watching some of this guy's stuff and realized some of you may not be familiar. Basically his show is Candid Camera meets a magician. This is a comp of a few of his exploits. I first learned of him when I was out at a meeting in Denver about 10yrs ago. The men I was sitting at the table with started talking about this show and said it was one of the funniest things they had seen. When I got home I started watching it....yes, it is funny.

View: https://www.youtube.com/watch?v=gIU09F8jdwc

2 Replies · 75 views

Load Replies (2) Reply Legacy View

Reactions: Jimbo

dishstaller

Oct 11, 2026

This one however is my all time favorite. Look at the way this guy holds the drill when he starts freaking out.

View: https://www.youtube.com/watch?v=Xt5DpFBtZwk&pp=ygUXY2FyYm9uYXJvIGVmZmVjdCByb21sZXk%3D

dishstaller

Yesterday at 9:17 PM

This is a Best Of compilation

View: https://www.youtube.com/watch?v=5-aR6JoVehU

Top

Back