Social Feed

S
Last reply · posted in DIRECTV General Forum
I have an H20 connected to a new 71" Sammy DLP via component and HDMI. Components work fine. HDMI works fine if H20 is set to 480i/p. But, if H20 is set to 720p, 1080i. or native, picture freezes every 3 seconds or so.

Sammy repair says it's a Dtv problem. You know what Directv says. I've already had the tv replaced - same problem.

Does anyone have any suggestion?
10 Replies · 2080 views
R
I have a samsung 50" DLP. THe HDMI does not work properly with my H20 either. I can switch the cable to my DVD player and it works fine. The problem has to be with D*.
T
There are posts in many of the forums about this problem. And not just with DirecTV by the way, there are problems with Dish receivers, cable boxes, HDMI switching receivers, upconverting DVD players etc etc The core of the problem is that different HDMI/HDCP implementations that are supposed to work with each other, don't. Often both the manufacturers say they are in specification, the spec seems just to be badly defined.

There are a couple of problems with Samsung and DirecTV receivers. First, many Samsung TVs do not support 480i resolution over HDMI. If you read the "fine print" in the user manual you will find a list of supported resolutions. If 480i is not in the list, you need to go into the H20 setup menu and uncheck 480i as a supported resolution, that way the H20 will not try to send 480i to the TV.
If that works, great.

If your TV does support 480i over HDMI, but you can't get HDMI to work, then there is a compatibility problem between the H20 and your TV. Many Samsung TVs, and a couple of other manufacturers, use a particular HDMI/HDCP chip - not made by Samsung, they buy it from a chip manufacturer - that the H20 HDMI implementation can't communicate with properly. It isn't clear which is at fault - the H20 works fine with many other TVs that don't use this chip, and the Samsung TVs work OK with other (but not all) cable and dish receivers. But whatever the problem, DirecTV is trying to modify the HDMI implementation on the H20 (which is basically in software, not a dedicated chipset) so that it is compatible with as many TVs as possible. They have already made changes to the HR20 software that have resulted in many of the HDMI problems going away. We assume that similar changes will be made to the H20 software, but have no idea when a software update will be available - rumor was it was going to be January but it didn't happen. Meanwhile you should just use component video connections.

Most people find that the picture quality on component is as good as HDMI. Some people report component gives a better picture than HDMI. Any difference between the two is most likely caused by different calibration on the inputs. Although HDMI is a digital connection, all the conversions going on in your receiver and in the TV have far more effect on picture quality than anything introduced by digital to analog conversion, especially with short component cables. And HDMI has its own issues, particularly with longer cables - it is fairly susceptible to interference, and needs equalization over long distances. Its main advantage is that it is a single cable solution. I have both HDMI and component in use on my system, using 6ft cables from monoprice.com (don't pay a lot for cables, it's not worth it) and both give great picture quality
S
Thanks, Texasbrit. I have now seen some of the other threads that you mentioned. What a mess; I hope D* is able to fix. My H20/Sammy plays via HDMI with the H20 set to 480i or 480p. All other settings do not work. 1080i using components give the best picture.
posstefmikala
I have a sammy 46in DLP and the H20 and it works fine over the HDMI cable.
P
I have a Pioneer PDP-5070HD 50" plasma and I have had the same issue. I have already returned a H20-100 which started the issue after 3 months. I then got a refurbished H20-600 which had the same issue after only 24 hours. The cable is good (tested on other components). My opinion the HDMI has better clarity, but for now I'm stuck with component connection until this new S/W comes out.
dfergie
Staff member HERE TO HELP YOU!
Last reply · posted in TV Shows
Stargate SG-1 cancelled, Atlantis renewed
clear.gif

Monday - August 21, 2006 | by Darren Sumner
clear.gif

The future of Stargate is in question today, as SCI FI Channel has cancelled the long-running Stargate SG-1, Multichannel News reported today and a GateWorld source has confirmed. The news regrettably follows the airing of the show's milestone two-hundredth episode on Friday.

Stargate Atlantis, meanwhile, has been renewed for a fourth season, with the network hoping to see that the spin-off series can stand alone, according to a source.
Source Gateworld
2034 Replies · 184177 views
R
I have gotten back into watching SG-1 and I have recorded most of the episodes to binge watch. What episodes are about the Antarctic or was this a movie? Also where could I watch the SG-1 movies?
osu1991
long_time_Dish
I have gotten back into watching SG-1 and I have recorded most of the episodes to binge watch. What episodes are about the Antarctic or was this a movie? Also where could I watch the SG-1 movies?
Well, there are a couple involving the Antarctic. "Solitudes", S1 E17 (one of my favorites), Then, "Lost City', S7 E21 and E22. Then, in the SGA pilot, "Rising", S1 E1 and E2, it starts out in the Antarctic for about the first 20 minutes or so.
R
Well, there are a couple involving the Antarctic. "Solitudes", S1 E17 (one of my favorites), Then, "Lost City', S7 E21 and E22. Then, in the SGA pilot, "Rising", S1 E1 and E2, it starts out in the Antarctic for about the first 20 minutes or so.
Which one has O'Neil being Ancients? I am at the end of Season 8 now.
long_time_Dish
Which one has O'Neil being Ancients? I am at the end of Season 8 now.
If I understand your question, O'Neill had the Ancient's knowledge in the "Lost City" two-part episode. That was when Anubis attacked Earth and there was a big battle over Antarctica.
  • Like
Reactions: dfergie and Foxbat
R
If I understand your question, O'Neill had the Ancient's knowledge in the "Lost City" two-part episode. That was when Anubis attacked Earth and there was a big battle over Antarctica.
Those are the episodes I am looking for. They are referred to a lot in the episodes I just recently watched.
  • Like
Reactions: dfergie
T
Last reply · posted in Free To Air (FTA) Discussion
Picked up a sweet directv dish, mount, twin lnbs and a short cable.
Has anyone converted one to FTA? A Frankenstein of sorts...
6 Replies · 291 views
B
would probably also work well for NHK on 101W and possibly for PBS on 99W. I used one for a while on 30W. Just keep in mind that because it's undersized for those satellites, it might work fine in clear weather but won't have much margin to account for signal degradation during rain/snow
  • Like
Reactions: TVHabit
O
If you can find one, the Shaw / Star Choice 75e ellipticals are great for use on 97, 99, and 101W. They are really just rebranded ChannelMaster 75 cm reflectors and use linear LNBFs by default out of the box.

Everyone else's mileage may vary.
  • Like
Reactions: TVHabit
T
I have read that some have converted this type dish but after giving it a good look, it's the lnb conversion that is the bottleneck. Does anyone have a picture of their attempt to configure the lnb? I watched a video on youtube from the save it for parts guy and he used duct tape! Guess it worked but I'm thinking something a bit more permanent!
Thanks to all for your interest and replies...
Titanium
Many of us have used a universal LNBF mount (or get creative with L brackets and plumbers tape - perforated metal strapping). Use a few inches of aluminum tube (or a piece of 1x2" lumber) to extend the support arm (replacing the plastic mount used by DirecTV and Dish) to place the LNBF throat opening at the correct distance from the reflector, the correct height and at the correct angle. Nothing magical... simply place the new linear LNBF in the center at the same distance, height and angle as the current combo.
www.amazon.com/Universal-Single-Bracket-Holder-FTA-US/dp/B074L85WK2
LNBF mount.webp
  • Like
Reactions: FTA4PA
k4otl
To add: 101W Ku seems to be (one of if not the) strongest for me, and if I only had Ku I definitely want 101W for the music mux, it's robust FEC and strong signal help a lot. I've thought about using a used Dish/DirectTV dish at my Dads to supplement his OTA (mainly for my benefit when I visit :) )
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in The Chit Chat Club
Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne


Get it?


An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
68539 Replies · 2673778 views
  • Like
Reactions: c-spand
long_time_Dish
Give A Little Bit - Supertramp
dishstaller
Little Wing - Jimi Hendrix
  • Like
Reactions: ClarkGable
long_time_Dish
With A Little Luck - Wings
  • Like
Reactions: ClarkGable
H
LITTLE Willy-Sweet
  • Like
Reactions: ClarkGable
ClarkGable
Little Deuce Coupe - The Beach Boys
meStevo
Lifetime Supporter
Last reply · posted in The Sports Section
Schedule drops tomorrow. Mandatory mini camps in June. Hall of Fame game August 6th.
116 Replies · 1854 views
  • Like
Reactions: Jimbo and dfergie
Foxbat
I guess even the patience of us laid-back Hoosiers has its limits:
rvvaquero
I guess even the patience of us laid-back Hoosiers has its limits:
Be nice to see a Cowboy headline like that.
M
I guess even the patience of us laid-back Hoosiers has its limits:

Can we expect to see a new coach if we say "pretty please?"
  • Like
Reactions: Foxbat
Foxbat
Jeeez, Week 6, no lead is safe…
Peter Parker
Supporting Founder Lifetime Supporter
Last reply · posted in DISH Network Support Forum
No idea what improvements might be involved.
24 Replies · 1110 views
  • Like
Reactions: LQQK and reubenray
N
I'm getting fabulous picture on Ch. 148 4k, but zero audio with H713. This is with a recorded show (Notre Dame game). Anyone else have this? Audio is fine on every other channel.
  • Like
Reactions: charlesrshell
jsmit86
I'm getting fabulous picture on Ch. 148 4k, but zero audio with H713. This is with a recorded show (Notre Dame game). Anyone else have this? Audio is fine on every other channel.
It's a known issue.
For a temporary fix, go into the menu, Audio, and turn Dolby Audio "OFF". You will have PCM stereo audio.

I was able to give the tech ops team some data logs so they could diagnose the problem, and they rolled me back to H708 temporarily. It fixed that issue.

They let me know that they understand what caused the issue, and it will be fixed within a few weeks in a new update.
long_time_Dish
They let me know that they understand what caused the issue, and it will be fixed within a few weeks in a new update.
Oh, you mean "soon"? :biggrin
Almighty1
It's a known issue.
For a temporary fix, go into the menu, Audio, and turn Dolby Audio "OFF". You will have PCM stereo audio.

I was able to give the tech ops team some data logs so they could diagnose the problem, and they rolled me back to H708 temporarily. It fixed that issue.

They let me know that they understand what caused the issue, and it will be fixed within a few weeks in a new update.
I guess they will be busy when lots of people start asking for rollbacks to H708 now that you mention that downgrades of software does exist because it will likely fix the OTA Single Tuner and the IR Remote problems in H710-H713.
navychop
it will likely fix the OTA Single Tuner

:popcorn
  • Like
Reactions: charlesrshell
dishstaller
it will likely fix the OTA Single Tuner
🤣

Oh....you were serious
  • Like
Reactions: charlesrshell
teachsac
Staff member HERE TO HELP YOU!
Last reply · posted in TV Shows
Hondo is back with a new squad 9/25 only on Starz.


View: https://m.youtube.com/shorts/b0gPzA8KHEQ
7 Replies · 122 views
  • Like
Reactions: dfergie
K
Never watched the previous shows, so doubtful.
teachsac
Started watching yesterday. Not too bad.
Scott Greczkowski
Wife likes it.
  • Like
Reactions: teachsac
teachsac
I like Zyra from La Brea (one with the prosthetic).
T
Last reply · posted in C-BAND Satellite Discussion
Howdy folks long time no write.

Issue(s): Horizontal transponders (esp. Weigel mux) breakup/mosaic/sputtering audio, JTV less so (but received perfectly up until a month or so ago.
Vertical is fine (Daystar). Up until recently couldn't even get any signal on Weigel Mux but JTV was perfect.

What I did to improve things: A slight westward move improved reception but only slightly (approx 72 on the micro HD, sorry no dB to post). I removed the 3-way C-Band splitter and used a 2-way to get a 1-2 db signal gain ( the power port goes to the Startrak - the micro HD doesn't have enough juice ! (1st clue) even after swapping the switching power supply it came with with a heftier linear 12 V supply (less RFI too !).
I have had issues with the uHD before signal breaking up that a reboot would clear up (clue #2 = dying tuner?) - FYI, I reinforced the IF input and removed all flux from the pcb completely with a Flux Removal Pen (MG Chemicals Cat No. 4140-P) which definitely makes a huge difference.

I went outside and pushed and pulled reflector slightly and no improvement. Pole (actually tower in yard - the neighbours love me..NOT) is plumb, checked with carpenters level. Dish was last peaked in 2017 or so, after overhauling 24" Von Weise, new Acme, fresh grease, etc. Focal length, f/d ratio etc meticulously adjusted. One panel has a tear so planning to repair that this weekend when my cousin comes over ( to help me out (old guy here) forecast calls for sunshine.

What has changed: My utility company has installed new high tension line poles (one smack dab in the middle of 101°W target! But they put it in last year and reception (of JTV (HOR) at least) was fine, BUT when they came out to transfer the wires over this year from the old (sawed in half) pole that's about when the troubles started (coincidence?), but again Daystar (VER) was fine. I always had this pole in the light of sight of 101° before with no issues. (fyi my zenith sat 74° is unobstucted, but can't test)

In the meantime Weigel mux is trying to break in MOSTLY in LATE at night (less cell usage?) (audio not video except for a frame here or there) so don't know what has changed with this mux which suddenly "woke up". I have never had to fuss with dish moves on this satellite ( the slightest move +/- motor clicks loses lock, wheres normally on C-band I can go significantly wider east or west and still have a strong signal ( have these gone "spot beam" or narrower somehow and what is the slight difference in Az listed on Lyngsat to 100.9° affect things ( isn't that the declination i.e. requiring a tweak of declination?).

Long story short (too late, ha), if I had another DVB-S2 box to try and / or a newer more stable PLL lnb ( I have been meaning to upgrade many a time but never got arround to it) I could determine if it's my antiquated receiving equipment, or my dish/feed alignment ( doubtful as it tracks everything from 55 °W to 133 ° W nicely.) or the dreaded 5G! (BUT only on HOR and not VER?).
I read another post where the OP (with his smaller 7.5 footer) played around with the illumination to peak desired transponder and reduce qrm on interfering/ stronger xpndrs (even on 103° W). So will play with that too - and cut away the RG-6 a and pull up a fresh section with new PPC and coax Seal. Open the throat cap see if any cobwebs are there and check servo operation (also changed in last maintence 10 years ago).

Finally, this will probably be the last chance I get to play with the BUD from the looks of it (providers leaving, auctioning off rest of spectrum imminent above 4.0 Ghz, and to keep the peace with neighbours so it would be nice to have that mux back for the long, cold and dark winters to comfort this old man before I call it quits and buy a VHF/UHF/FM Yagi and get MeTV, H&I from my Vermont local stations (checked at a friends today and they come in nicely - except ABC) .
Only one guy in town (Montreal) I may be able to get a receiver or PLL lnb from to try (RPS Sat) so hopefully with elimnate that as a possible culprit. Be nice to pick up a cheap or used PLL lnb to try w/o 5G BPF (money is tight )

Like others I couldn't care less about "tv" (well maybe just a liitle or a lot) it's the challenge that excites me , I can get MeTV other ways OTA (no pirate crap).

So what do you guys (and gals) think ?. p.s. I don't have a spectrum analyzer and there are def/ cell towers nearby (half a Km or so away).
Oh and time permitting will hammer out dings too and wire damaged mesh on one section for an extra dB or two. Hesitate to touch Declination, Elevation and pole mount but will play around with those a little too... Why is this mux for finicky suddenly ?(8psk, 5/6 fec, beamwidthetc.. man wish they went back to VER I think everthing would be fine! For the engineers out here does 5G QRM affect one poliarization (HOR) more than another (VER)? I understand the strong interference swamps out the input mixer/local oscilator in the hapless old C-band lnb (I think it at time affect KU too esp. LPB on 101°W KU - incidentally thos were weak or "gone' but are back almost at the time MeTV improved..hmm Terrestrial interference?

Any thoughts or suggestions ( cheap or free solutions please) greatly appreciated. Cheers.

p.p.s. Micro HD can't display Decades and Toons but records them fine so I can watch on another box/media player (Ali chip set issue). Another reason to upgrade.

Anybody interested in a nice C/KU system free ? (for next Spring/Summer 2027)

[Sami 10' mesh, Corotor II+, Eagle Aspen (very old) C-band lnb, Norsat Ku lnb, Channel Master C/Ku (H/V) switch, Startrak 400 Analog receiver w/ motor control, Geosat uHD DVD-S2, CW600S for Mpeg-2]
9 Replies · 362 views
cyberham
With the microHD connected this afternoon and tuned to the Weigel mux, I can receive the mux well.

My conclusion is that the sensitivity of the receivers in descending order of sensitivity is as follows:
  • V9 Prime (best)
  • microHD
  • Edision osmio4k+
Either the V9 or the microHD could be used to watch Weigel but the Edision really could not with my given dish situation, at least during the daytime. At night, the signal is stronger here and then maybe the Edision could be used.

Weigel mux.webp
Titanium
What is the SNR readings for these transponders? Is the signal breaking up due to low SNR or interference?

Did you inspect the feedhorn throat and wave guide for wasp nest or other blockage? Good SNR with frequent drops in decoding ( loss of SQ readings) could indicate interference from 5G.
T
Appreciate you checking. I should be picking these up with the tenner so still not done tuning up the bud - fell off ladder last week and hit my head!

Started over from scratch, N/S alignment, El/Decl extreme West sat, played with feed f/d checking everything and getting nice signals but still 101 west is PIA. New lnb was defective and returned it. My old one is fine but would have liked to A/B with a better lnb.

Thought it was the servo there because I was out and set everything up by the dish and flipping to HOR made a strange noise -BUT ONLY on 101 W ! All other sats skew is fine..hmm ( I have the skew almost perfect, use "Arrow" template on Zenith Sat (well nothing on 74 W to check with but Nimiq 5 at 72.6 W is closest and luckily picking up R- Pol channel from Canada to test with. Anyway picking up a new servo to try (the obvious polarity culprit).

Q. Back in the day PAS9 (74 W) was used but now I have to use closest zenith sat (Nimiq 5). I can't perfectly peak on that one which is 1 degree off (N/S alignment error). I used my trusty Brunton compass and even true noon shadow off pole to hit south.

I did have to peak extreme west by rotating mount ever so slighty so tracking extreme pretty good, but top and middle can use an elevation tweak (esp. Ku) to bring them back to where they were. No fun as the weather has been miserable and still dizzy from fall.

Oh and the Freesat V8 is crap (the tuner pixelates when the uHD is solid!) but love that SCART connector for S-Video out ! (I record to my Pio DVR and burn to DVD classic tv shows).

Stay tuned

With the microHD connected this afternoon and tuned to the Weigel mux, I can receive the mux well.
T
Did you inspect the feedhorn throat and wave guide for wasp nest or other blockage? Good SNR with frequent drops in decoding ( loss of SQ readings) could indicate interference from 5G.

Thanks for chiming in here. No wasps (or hornets nests) but good suggestion.

I am getting 70 and over Quality on uHD which is good but as you say the signal drops out (70 to 0 ) occasionally and much worse by day (even JTV which I used to get solid is a mess in the day. Again Daystar (VER) is fine but still not what it used to be.

I will will either have to get a BPF or go VHF/UHF for these channels but not giving up just yet!

p.s. Isn't there something between your feedhorn/lnbf BPF model and Norsat's 1500$ BPF and 5G filtering lnb's? Heck almost ready for a diy (reverse engineer) job here (microwave BPF hack) Ah where is Radio Electronics when you need it! If it wasn't for losing Ku I'd buy your lnbf in a heartbeat! Are these hard to add Ku to?
Titanium
Our LNBFs are integrated with the feedhorn and no KU option. Maybe install an inline waveguide BPF such as:

www.ebay.com/itm/158077455896
www.ebay.com/itm/960059145385
www.ebay.com/itm/158007483799
B
Howdy folks long time no write.

Issue(s): Horizontal transponders (esp. Weigel mux) breakup/mosaic/sputtering audio, JTV less so (but received perfectly up until a month or so ago.
Vertical is fine (Daystar). Up until recently couldn't even get any signal on Weigel Mux but JTV was perfect.

What I did to improve things: A slight westward move improved reception but only slightly (approx 72 on the micro HD, sorry no dB to post). I removed the 3-way C-Band splitter and used a 2-way to get a 1-2 db signal gain ( the power port goes to the Startrak - the micro HD doesn't have enough juice ! (1st clue) even after swapping the switching power supply it came with with a heftier linear 12 V supply (less RFI too !).
I have had issues with the uHD before signal breaking up that a reboot would clear up (clue #2 = dying tuner?) - FYI, I reinforced the IF input and removed all flux from the pcb completely with a Flux Removal Pen (MG Chemicals Cat No. 4140-P) which definitely makes a huge difference.

I went outside and pushed and pulled reflector slightly and no improvement. Pole (actually tower in yard - the neighbours love me..NOT) is plumb, checked with carpenters level. Dish was last peaked in 2017 or so, after overhauling 24" Von Weise, new Acme, fresh grease, etc. Focal length, f/d ratio etc meticulously adjusted. One panel has a tear so planning to repair that this weekend when my cousin comes over ( to help me out (old guy here) forecast calls for sunshine.

What has changed: My utility company has installed new high tension line poles (one smack dab in the middle of 101°W target! But they put it in last year and reception (of JTV (HOR) at least) was fine, BUT when they came out to transfer the wires over this year from the old (sawed in half) pole that's about when the troubles started (coincidence?), but again Daystar (VER) was fine. I always had this pole in the light of sight of 101° before with no issues. (fyi my zenith sat 74° is unobstucted, but can't test)

In the meantime Weigel mux is trying to break in MOSTLY in LATE at night (less cell usage?) (audio not video except for a frame here or there) so don't know what has changed with this mux which suddenly "woke up". I have never had to fuss with dish moves on this satellite ( the slightest move +/- motor clicks loses lock, wheres normally on C-band I can go significantly wider east or west and still have a strong signal ( have these gone "spot beam" or narrower somehow and what is the slight difference in Az listed on Lyngsat to 100.9° affect things ( isn't that the declination i.e. requiring a tweak of declination?).

Long story short (too late, ha), if I had another DVB-S2 box to try and / or a newer more stable PLL lnb ( I have been meaning to upgrade many a time but never got arround to it) I could determine if it's my antiquated receiving equipment, or my dish/feed alignment ( doubtful as it tracks everything from 55 °W to 133 ° W nicely.) or the dreaded 5G! (BUT only on HOR and not VER?).
I read another post where the OP (with his smaller 7.5 footer) played around with the illumination to peak desired transponder and reduce qrm on interfering/ stronger xpndrs (even on 103° W). So will play with that too - and cut away the RG-6 a and pull up a fresh section with new PPC and coax Seal. Open the throat cap see if any cobwebs are there and check servo operation (also changed in last maintence 10 years ago).

Finally, this will probably be the last chance I get to play with the BUD from the looks of it (providers leaving, auctioning off rest of spectrum imminent above 4.0 Ghz, and to keep the peace with neighbours so it would be nice to have that mux back for the long, cold and dark winters to comfort this old man before I call it quits and buy a VHF/UHF/FM Yagi and get MeTV, H&I from my Vermont local stations (checked at a friends today and they come in nicely - except ABC) .
Only one guy in town (Montreal) I may be able to get a receiver or PLL lnb from to try (RPS Sat) so hopefully with elimnate that as a possible culprit. Be nice to pick up a cheap or used PLL lnb to try w/o 5G BPF (money is tight )

Like others I couldn't care less about "tv" (well maybe just a liitle or a lot) it's the challenge that excites me , I can get MeTV other ways OTA (no pirate crap).

So what do you guys (and gals) think ?. p.s. I don't have a spectrum analyzer and there are def/ cell towers nearby (half a Km or so away).
Oh and time permitting will hammer out dings too and wire damaged mesh on one section for an extra dB or two. Hesitate to touch Declination, Elevation and pole mount but will play around with those a little too... Why is this mux for finicky suddenly ?(8psk, 5/6 fec, beamwidthetc.. man wish they went back to VER I think everthing would be fine! For the engineers out here does 5G QRM affect one poliarization (HOR) more than another (VER)? I understand the strong interference swamps out the input mixer/local oscilator in the hapless old C-band lnb (I think it at time affect KU too esp. LPB on 101°W KU - incidentally thos were weak or "gone' but are back almost at the time MeTV improved..hmm Terrestrial interference?

Any thoughts or suggestions ( cheap or free solutions please) greatly appreciated. Cheers.

p.p.s. Micro HD can't display Decades and Toons but records them fine so I can watch on another box/media player (Ali chip set issue). Another reason to upgrade.

Anybody interested in a nice C/KU system free ? (for next Spring/Summer 2027)

[Sami 10' mesh, Corotor II+, Eagle Aspen (very old) C-band lnb, Norsat Ku lnb, Channel Master C/Ku (H/V) switch, Startrak 400 Analog receiver w/ motor control, Geosat uHD DVD-S2, CW600S for Mpeg-2]
I had the EXACT same problem happen to me with 101w, MeTV mux (Weigel). Working great when about 3 weeks ago I started to get the pixelating, especially at night. Sometimes Jewelry TV would also do it, sometimes not. Tweaked my dish. I have a Titanium 240 feed with the 5G filter 4.0-4.2 band pass. Every other satellite is working fine. Something on their end for sure. Power reduction? My signal seems fine like always. Running a Winegard 8.5 ft dish using a GT Media UHD V8. I'm sure my receiver isn't maybe sensitive enough for lower signal levels. Frustrating here too. I'm in the Canton, Ohio area. Thanks!