Social Feed
Have a newly installed HR20-700s up and running just fine but I can not get the remotes to work in RF mode. I've set the receiver and remotes up many times to no avail. It actually worked once for a couple of seconds but only when the remote was within about 3 feet of the receiver. Hasn't worked since. Works fine in IR mode. I even unplugged every RF device in the house...cordless phones and wifi access point -same. I'm in a rural location so doubt there is any RF interference from anywhere else.
I've set up the receiver many times for RF and same with both RC34 and RC24RF remotes. When programming the remotes I'm following the instructions by pressing Mute & Select at the same time until I get 2 blinks, entering 9-6-1, pressing Channel Up, entering the RID# (110150 in my case) and then pressing Select - doesn't work. Tried fresh Duracell batteries as well - same.
My gut feeling tells me the RF section of the receiver is defective or internal antenna may not be connected. This receiver does NOT have a place to hook up an external antenna like the one that came in the RF24RF kit.
Anybody have any ideas? Dread the call to DirecTV tech support.
Thanks,
stumo
I've set up the receiver many times for RF and same with both RC34 and RC24RF remotes. When programming the remotes I'm following the instructions by pressing Mute & Select at the same time until I get 2 blinks, entering 9-6-1, pressing Channel Up, entering the RID# (110150 in my case) and then pressing Select - doesn't work. Tried fresh Duracell batteries as well - same.
My gut feeling tells me the RF section of the receiver is defective or internal antenna may not be connected. This receiver does NOT have a place to hook up an external antenna like the one that came in the RF24RF kit.
Anybody have any ideas? Dread the call to DirecTV tech support.
Thanks,
stumo
14 Replies
·
4079 views
S
Yes, it says made in China
Can you give a clue as to how you know this? Looking for ammo in case Directv gives some resistance in replacing the receiver.
Will being calling here in a few minutes to see if I can get it replaced.
Thanks,
Stu
Yes, it says made in China
Can you give a clue as to how you know this? Looking for ammo in case Directv gives some resistance in replacing the receiver.Will being calling here in a few minutes to see if I can get it replaced.
Thanks,
Stu
S
Called Directv this morning and once I got to what I'll call Level 3 support, the guy agreed that he too thought it is a defective receiver and is sending another one out.
I must say everyone I talked to was friendly and tried to help the best they could. Will give them an "A" for customer support.
Now I just hope the replacement wasn't made in China
Thanks everyone,
stumo
I must say everyone I talked to was friendly and tried to help the best they could. Will give them an "A" for customer support.
Now I just hope the replacement wasn't made in China
Thanks everyone,
stumo
Called Directv this morning and once I got to what I'll call Level 3 support, the guy agreed that he too thought it is a defective receiver and is sending another one out.
I must say everyone I talked to was friendly and tried to help the best they could. Will give them an "A" for customer support.
Now I just hope the replacement wasn't made in China
Thanks everyone,
stumo
Don't worry about the China thing...
All the HR20-700's are made by "Pace Micro" regardless, so far they are the only ones making them, If you look at the over all picture, it's a very small percentage that are having any problems.
Jimbo
TWiT Tech Podcast Network
Time for another AWESOME video from the TWIT Network!
View: https://www.youtube.com/shorts/ET_7F3I6C5s
Direct YouTube Link - America's $10 Trillion AI Boom Is Starting to Crack #shorts
TWIT's Website
TWIT Live Feed
View: https://www.youtube.com/shorts/ET_7F3I6C5s
Direct YouTube Link - America's $10 Trillion AI Boom Is Starting to Crack #shorts
TWIT's Website
TWIT Live Feed
0 Replies
·
0 views
Howdy folks long time no write.
Issue(s): Horizontal transponders (esp. Weigel mux) breakup/mosaic/sputtering audio, JTV less so (but received perfectly up until a month or so ago.
Vertical is fine (Daystar). Up until recently couldn't even get any signal on Weigel Mux but JTV was perfect.
What I did to improve things: A slight westward move improved reception but only slightly (approx 72 on the micro HD, sorry no dB to post). I removed the 3-way C-Band splitter and used a 2-way to get a 1-2 db signal gain ( the power port goes to the Startrak - the micro HD doesn't have enough juice ! (1st clue) even after swapping the switching power supply it came with with a heftier linear 12 V supply (less RFI too !).
I have had issues with the uHD before signal breaking up that a reboot would clear up (clue #2 = dying tuner?) - FYI, I reinforced the IF input and removed all flux from the pcb completely with a Flux Removal Pen (MG Chemicals Cat No. 4140-P) which definitely makes a huge difference.
I went outside and pushed and pulled reflector slightly and no improvement. Pole (actually tower in yard - the neighbours love me..NOT) is plumb, checked with carpenters level. Dish was last peaked in 2017 or so, after overhauling 24" Von Weise, new Acme, fresh grease, etc. Focal length, f/d ratio etc meticulously adjusted. One panel has a tear so planning to repair that this weekend when my cousin comes over ( to help me out (old guy here) forecast calls for sunshine.
What has changed: My utility company has installed new high tension line poles (one smack dab in the middle of 101°W target! But they put it in last year and reception (of JTV (HOR) at least) was fine, BUT when they came out to transfer the wires over this year from the old (sawed in half) pole that's about when the troubles started (coincidence?), but again Daystar (VER) was fine. I always had this pole in the light of sight of 101° before with no issues. (fyi my zenith sat 74° is unobstucted, but can't test)
In the meantime Weigel mux is trying to break in MOSTLY in LATE at night (less cell usage?) (audio not video except for a frame here or there) so don't know what has changed with this mux which suddenly "woke up". I have never had to fuss with dish moves on this satellite ( the slightest move +/- motor clicks loses lock, wheres normally on C-band I can go significantly wider east or west and still have a strong signal ( have these gone "spot beam" or narrower somehow and what is the slight difference in Az listed on Lyngsat to 100.9° affect things ( isn't that the declination i.e. requiring a tweak of declination?).
Long story short (too late, ha), if I had another DVB-S2 box to try and / or a newer more stable PLL lnb ( I have been meaning to upgrade many a time but never got arround to it) I could determine if it's my antiquated receiving equipment, or my dish/feed alignment ( doubtful as it tracks everything from 55 °W to 133 ° W nicely.) or the dreaded 5G! (BUT only on HOR and not VER?).
I read another post where the OP (with his smaller 7.5 footer) played around with the illumination to peak desired transponder and reduce qrm on interfering/ stronger xpndrs (even on 103° W). So will play with that too - and cut away the RG-6 a and pull up a fresh section with new PPC and coax Seal. Open the throat cap see if any cobwebs are there and check servo operation (also changed in last maintence 10 years ago).
Finally, this will probably be the last chance I get to play with the BUD from the looks of it (providers leaving, auctioning off rest of spectrum imminent above 4.0 Ghz, and to keep the peace with neighbours so it would be nice to have that mux back for the long, cold and dark winters to comfort this old man before I call it quits and buy a VHF/UHF/FM Yagi and get MeTV, H&I from my Vermont local stations (checked at a friends today and they come in nicely - except ABC) .
Only one guy in town (Montreal) I may be able to get a receiver or PLL lnb from to try (RPS Sat) so hopefully with elimnate that as a possible culprit. Be nice to pick up a cheap or used PLL lnb to try w/o 5G BPF (money is tight )
Like others I couldn't care less about "tv" (well maybe just a liitle or a lot) it's the challenge that excites me , I can get MeTV other ways OTA (no pirate crap).
So what do you guys (and gals) think ?. p.s. I don't have a spectrum analyzer and there are def/ cell towers nearby (half a Km or so away).
Oh and time permitting will hammer out dings too and wire damaged mesh on one section for an extra dB or two. Hesitate to touch Declination, Elevation and pole mount but will play around with those a little too... Why is this mux for finicky suddenly ?(8psk, 5/6 fec, beamwidthetc.. man wish they went back to VER I think everthing would be fine! For the engineers out here does 5G QRM affect one poliarization (HOR) more than another (VER)? I understand the strong interference swamps out the input mixer/local oscilator in the hapless old C-band lnb (I think it at time affect KU too esp. LPB on 101°W KU - incidentally thos were weak or "gone' but are back almost at the time MeTV improved..hmm Terrestrial interference?
Any thoughts or suggestions ( cheap or free solutions please) greatly appreciated. Cheers.
p.p.s. Micro HD can't display Decades and Toons but records them fine so I can watch on another box/media player (Ali chip set issue). Another reason to upgrade.
Anybody interested in a nice C/KU system free ? (for next Spring/Summer 2027)
[Sami 10' mesh, Corotor II+, Eagle Aspen (very old) C-band lnb, Norsat Ku lnb, Channel Master C/Ku (H/V) switch, Startrak 400 Analog receiver w/ motor control, Geosat uHD DVD-S2, CW600S for Mpeg-2]
Issue(s): Horizontal transponders (esp. Weigel mux) breakup/mosaic/sputtering audio, JTV less so (but received perfectly up until a month or so ago.
Vertical is fine (Daystar). Up until recently couldn't even get any signal on Weigel Mux but JTV was perfect.
What I did to improve things: A slight westward move improved reception but only slightly (approx 72 on the micro HD, sorry no dB to post). I removed the 3-way C-Band splitter and used a 2-way to get a 1-2 db signal gain ( the power port goes to the Startrak - the micro HD doesn't have enough juice ! (1st clue) even after swapping the switching power supply it came with with a heftier linear 12 V supply (less RFI too !).
I have had issues with the uHD before signal breaking up that a reboot would clear up (clue #2 = dying tuner?) - FYI, I reinforced the IF input and removed all flux from the pcb completely with a Flux Removal Pen (MG Chemicals Cat No. 4140-P) which definitely makes a huge difference.
I went outside and pushed and pulled reflector slightly and no improvement. Pole (actually tower in yard - the neighbours love me..NOT) is plumb, checked with carpenters level. Dish was last peaked in 2017 or so, after overhauling 24" Von Weise, new Acme, fresh grease, etc. Focal length, f/d ratio etc meticulously adjusted. One panel has a tear so planning to repair that this weekend when my cousin comes over ( to help me out (old guy here) forecast calls for sunshine.
What has changed: My utility company has installed new high tension line poles (one smack dab in the middle of 101°W target! But they put it in last year and reception (of JTV (HOR) at least) was fine, BUT when they came out to transfer the wires over this year from the old (sawed in half) pole that's about when the troubles started (coincidence?), but again Daystar (VER) was fine. I always had this pole in the light of sight of 101° before with no issues. (fyi my zenith sat 74° is unobstucted, but can't test)
In the meantime Weigel mux is trying to break in MOSTLY in LATE at night (less cell usage?) (audio not video except for a frame here or there) so don't know what has changed with this mux which suddenly "woke up". I have never had to fuss with dish moves on this satellite ( the slightest move +/- motor clicks loses lock, wheres normally on C-band I can go significantly wider east or west and still have a strong signal ( have these gone "spot beam" or narrower somehow and what is the slight difference in Az listed on Lyngsat to 100.9° affect things ( isn't that the declination i.e. requiring a tweak of declination?).
Long story short (too late, ha), if I had another DVB-S2 box to try and / or a newer more stable PLL lnb ( I have been meaning to upgrade many a time but never got arround to it) I could determine if it's my antiquated receiving equipment, or my dish/feed alignment ( doubtful as it tracks everything from 55 °W to 133 ° W nicely.) or the dreaded 5G! (BUT only on HOR and not VER?).
I read another post where the OP (with his smaller 7.5 footer) played around with the illumination to peak desired transponder and reduce qrm on interfering/ stronger xpndrs (even on 103° W). So will play with that too - and cut away the RG-6 a and pull up a fresh section with new PPC and coax Seal. Open the throat cap see if any cobwebs are there and check servo operation (also changed in last maintence 10 years ago).
Finally, this will probably be the last chance I get to play with the BUD from the looks of it (providers leaving, auctioning off rest of spectrum imminent above 4.0 Ghz, and to keep the peace with neighbours so it would be nice to have that mux back for the long, cold and dark winters to comfort this old man before I call it quits and buy a VHF/UHF/FM Yagi and get MeTV, H&I from my Vermont local stations (checked at a friends today and they come in nicely - except ABC) .
Only one guy in town (Montreal) I may be able to get a receiver or PLL lnb from to try (RPS Sat) so hopefully with elimnate that as a possible culprit. Be nice to pick up a cheap or used PLL lnb to try w/o 5G BPF (money is tight )
Like others I couldn't care less about "tv" (well maybe just a liitle or a lot) it's the challenge that excites me , I can get MeTV other ways OTA (no pirate crap).
So what do you guys (and gals) think ?. p.s. I don't have a spectrum analyzer and there are def/ cell towers nearby (half a Km or so away).
Oh and time permitting will hammer out dings too and wire damaged mesh on one section for an extra dB or two. Hesitate to touch Declination, Elevation and pole mount but will play around with those a little too... Why is this mux for finicky suddenly ?(8psk, 5/6 fec, beamwidthetc.. man wish they went back to VER I think everthing would be fine! For the engineers out here does 5G QRM affect one poliarization (HOR) more than another (VER)? I understand the strong interference swamps out the input mixer/local oscilator in the hapless old C-band lnb (I think it at time affect KU too esp. LPB on 101°W KU - incidentally thos were weak or "gone' but are back almost at the time MeTV improved..hmm Terrestrial interference?
Any thoughts or suggestions ( cheap or free solutions please) greatly appreciated. Cheers.
p.p.s. Micro HD can't display Decades and Toons but records them fine so I can watch on another box/media player (Ali chip set issue). Another reason to upgrade.
Anybody interested in a nice C/KU system free ? (for next Spring/Summer 2027)
[Sami 10' mesh, Corotor II+, Eagle Aspen (very old) C-band lnb, Norsat Ku lnb, Channel Master C/Ku (H/V) switch, Startrak 400 Analog receiver w/ motor control, Geosat uHD DVD-S2, CW600S for Mpeg-2]
10 Replies
·
372 views
With the microHD connected this afternoon and tuned to the Weigel mux, I can receive the mux well.
My conclusion is that the sensitivity of the receivers in descending order of sensitivity is as follows:
My conclusion is that the sensitivity of the receivers in descending order of sensitivity is as follows:
- V9 Prime (best)
- microHD
- Edision osmio4k+
Staff member
HERE TO HELP YOU!
Cutting Edge
Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!
So let the game continue!
The last song was added by Bobby who posted...
One Meat Ball - Andrews Sisters
CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!
Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game
Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.
Example:
Long Live Rock and Roll -- Rainbow
Rainbow in the Dark -- Dio
Another example:
Ride the Lightning -- Metallica
Lightning Strikes -- Ozzy Osbourne
Get it?
An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
So let the game continue!
The last song was added by Bobby who posted...
One Meat Ball - Andrews Sisters
CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!
Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game
Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.
Example:
Long Live Rock and Roll -- Rainbow
Rainbow in the Dark -- Dio
Another example:
Ride the Lightning -- Metallica
Lightning Strikes -- Ozzy Osbourne
Get it?
An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
68541 Replies
·
2673855 views
Booredatwork.com
Time for another AWESOME video from BoredAtWork!
View: https://www.youtube.com/watch?v=LxeUBPus6bc
Direct YouTube Link - Alexa Tablet 12 Pro Review: This Isn't A Fire Tablet!
Booredatwork.com Website
Booredatwork on Facebook
View: https://www.youtube.com/watch?v=LxeUBPus6bc
Direct YouTube Link - Alexa Tablet 12 Pro Review: This Isn't A Fire Tablet!
Booredatwork.com Website
Booredatwork on Facebook
0 Replies
·
5 views
Lifetime Supporter
Schedule drops tomorrow. Mandatory mini camps in June. Hall of Fame game August 6th.
117 Replies
·
1869 views
I guess even the patience of us laid-back Hoosiers has its limits:
www.colts.com
Colts relieve general manager Chris Ballard of his duties
Colts Owner & CEO Carlie Irsay-Gordon released a statement Monday announcing the news.
www.colts.com
Be nice to see a Cowboy headline like that.I guess even the patience of us laid-back Hoosiers has its limits:
Colts relieve general manager Chris Ballard of his duties
Colts Owner & CEO Carlie Irsay-Gordon released a statement Monday announcing the news.
M
Can we expect to see a new coach if we say "pretty please?"
I guess even the patience of us laid-back Hoosiers has its limits:
Colts relieve general manager Chris Ballard of his duties
Colts Owner & CEO Carlie Irsay-Gordon released a statement Monday announcing the news.
Can we expect to see a new coach if we say "pretty please?"
I thought I would come here and find lots of complaints about the update to the dish anywhere mobile app, but am not seeing any. It used to look just like the desktop webpage. Now you can no longer filter by sports channels or movie channels. Plus that they made it look like a big button telephone and you see fewer channels in the screen which requires more scrolling. Yes I realize you can look at sports then select which sport you want to look at, I just liked being able to see all sporting events in the guide with all other channels being filtered out. Am I alone in the wilderness on this?
8 Replies
·
286 views
Staff member
HERE TO HELP YOU!
Stargate SG-1 cancelled, Atlantis renewed
Monday - August 21, 2006 | by Darren Sumner
The future of Stargate is in question today, as SCI FI Channel has cancelled the long-running Stargate SG-1, Multichannel News reported today and a GateWorld source has confirmed. The news regrettably follows the airing of the show's milestone two-hundredth episode on Friday.
Stargate Atlantis, meanwhile, has been renewed for a fourth season, with the network hoping to see that the spin-off series can stand alone, according to a source.
Source Gateworld
Monday - August 21, 2006 | by Darren Sumner
The future of Stargate is in question today, as SCI FI Channel has cancelled the long-running Stargate SG-1, Multichannel News reported today and a GateWorld source has confirmed. The news regrettably follows the airing of the show's milestone two-hundredth episode on Friday.
Stargate Atlantis, meanwhile, has been renewed for a fourth season, with the network hoping to see that the spin-off series can stand alone, according to a source.
Source Gateworld
2034 Replies
·
184187 views
Watch Stargate SG-1 for Free Online | Pluto TV
Stargate SG-1 picks up where the blockbuster film left off as the SG-1 team sets out to explore the mysteries of the Stargate and the worlds beyond it in the pulse-pounding series which became a worldwide phenomenon and a science fiction classic. Stream Stargate SG-1 for free on Pluto TV.
pluto.tv
TFLEV
Time for another AWESOME video from TFL Electric Vehicles!
View: https://www.youtube.com/watch?v=-Ca9w7HnuXg
Direct YouTube Link - 2027 BMW iX5 Walkaround & Review // They Have To Get This One Right!
View: https://www.youtube.com/watch?v=-Ca9w7HnuXg
Direct YouTube Link - 2027 BMW iX5 Walkaround & Review // They Have To Get This One Right!
0 Replies
·
13 views
Picked up a sweet directv dish, mount, twin lnbs and a short cable.
Has anyone converted one to FTA? A Frankenstein of sorts...
Has anyone converted one to FTA? A Frankenstein of sorts...
6 Replies
·
299 views
Many of us have used a universal LNBF mount (or get creative with L brackets and plumbers tape - perforated metal strapping). Use a few inches of aluminum tube (or a piece of 1x2" lumber) to extend the support arm (replacing the plastic mount used by DirecTV and Dish) to place the LNBF throat opening at the correct distance from the reflector, the correct height and at the correct angle. Nothing magical... simply place the new linear LNBF in the center at the same distance, height and angle as the current combo.
www.amazon.com/Universal-Single-Bracket-Holder-FTA-US/dp/B074L85WK2
www.amazon.com/Universal-Single-Bracket-Holder-FTA-US/dp/B074L85WK2
To add: 101W Ku seems to be (one of if not the) strongest for me, and if I only had Ku I definitely want 101W for the music mux, it's robust FEC and strong signal help a lot. I've thought about using a used Dish/DirectTV dish at my Dads to supplement his OTA (mainly for my benefit when I visit 
)
)
Supporting Founder
Lifetime Supporter
No idea what improvements might be involved.
24 Replies
·
1129 views
