Social Feed
I have an HR21 and all of the upgrades have appeared.
When I connect my ethernet cable to the HR21 and run the test I get confirmation for Network but can't connect to Internet on HR21 or computer. Internet works fine when not connected to HR21. How can I find help?
I waited for an hour on hold with DTV. I have a DSL modem and a Linksys router.
When I connect my ethernet cable to the HR21 and run the test I get confirmation for Network but can't connect to Internet on HR21 or computer. Internet works fine when not connected to HR21. How can I find help? I waited for an hour on hold with DTV. I have a DSL modem and a Linksys router.
35 Replies
·
5957 views
Rad, I've played with this some and no luck. I'm wondering if what I need is a router instead of a switch.
redbandit I'm glad you got your setup fixed. My local cc has a router like yours in stock for $40.
I Googled the modem # you gave me and saw that it would act as a router if you did a firmware upgrade, wonder if there was still an issue with that? You might want to review the documention for that modem with the firmware upgrade and make sure it's configured for the router function. Or as you said, just spend the $'s and get a router. When I was working I did a lot of support for work at home folks and the Linksys BEFSR41 worked nicely for them. Good luck getting it resolved.
I can't believe it!
I just got an e-mail from DTV with a number and PIN to call. The first CS rep said "This is getting out of my league, I will transfer you to the Internet department." I told him my problem, he had me go to menu>network>restore network defaults.
I did this and....voila...it worked!
BUT here's the kicker. I must have tried this exact procedure 10 times before and it never worked. I don't know why or how but I am now connected. (let's hope it lasts...at least my PIN is good for 5 days.)
I just got an e-mail from DTV with a number and PIN to call. The first CS rep said "This is getting out of my league, I will transfer you to the Internet department." I told him my problem, he had me go to menu>network>restore network defaults.
I did this and....voila...it worked!
BUT here's the kicker. I must have tried this exact procedure 10 times before and it never worked. I don't know why or how but I am now connected. (let's hope it lasts...at least my PIN is good for 5 days.)
Supporting Founder
Lifetime Supporter
I was reading this article
thehill.com
That said this-
Last summer, for the first time, streaming services like Netflix and Amazon Prime claimed the largest share of the television viewing audience, surpassing both cable and broadcast TV. Streaming captured 34.8 percent of July viewers, according to Nielsen data, compared to 34.4 percent for cable and 21.6 percent for broadcast.
And then, sometime in the second half of 2022, cord-cutters became the majority. The share of cable and satellite television subscribers dipped to 48 percent, according to a report from Samba TV, a television technology company.
Now I do not consider those with YTTV and the likes, Cord Cutters, but they still do not have Traditional Cable/Satellite delivered Live TV, so I decided to do the math.
There are, now, 129 Million Households in the United States.
In 2015, there were 100 Million Cable/Sat Subscribers , no streaming Live TV Service.
Today, there are 66 Million Live TV subscribers, including Cable, Satellite and Streaming.
Roughly, Streaming Live TV has 14 Million subs including all of them.
So that means, Cable/Satellite now has, roughly, 51 Million Households
So in just 8 years, lost 49% of their subscribers and by the end of this year, expected sub count to be, roughly, 45 million households.
That means a total loss of 55% since 2015 at the end of 2023.
But out of 129 Million households, 45 million will mean only 35% will get Cable/Satellite Delivered Live TV by the end of 2023.
Imagine what 2024 will be like.
Cable TV ‘cord-cutters’ became the majority in 2022
The steady decline of cable and broadcast television, and the rise of streaming services, reached a sort of inflection point over the past year. Last summer, for the first time, streaming ser…
thehill.com
That said this-
Last summer, for the first time, streaming services like Netflix and Amazon Prime claimed the largest share of the television viewing audience, surpassing both cable and broadcast TV. Streaming captured 34.8 percent of July viewers, according to Nielsen data, compared to 34.4 percent for cable and 21.6 percent for broadcast.
And then, sometime in the second half of 2022, cord-cutters became the majority. The share of cable and satellite television subscribers dipped to 48 percent, according to a report from Samba TV, a television technology company.
Now I do not consider those with YTTV and the likes, Cord Cutters, but they still do not have Traditional Cable/Satellite delivered Live TV, so I decided to do the math.
There are, now, 129 Million Households in the United States.
In 2015, there were 100 Million Cable/Sat Subscribers , no streaming Live TV Service.
Today, there are 66 Million Live TV subscribers, including Cable, Satellite and Streaming.
Roughly, Streaming Live TV has 14 Million subs including all of them.
So that means, Cable/Satellite now has, roughly, 51 Million Households
So in just 8 years, lost 49% of their subscribers and by the end of this year, expected sub count to be, roughly, 45 million households.
That means a total loss of 55% since 2015 at the end of 2023.
But out of 129 Million households, 45 million will mean only 35% will get Cable/Satellite Delivered Live TV by the end of 2023.
Imagine what 2024 will be like.
880 Replies
·
71387 views
Sony is discontinuing it's last 4K disc player, Panasonic has been rumored to be doing the same, the end of physical media is unfortunately, about to happen.
cordcuttersnews.com
Bad News For Blu-ray Fans: Sony Has Stopped Making a Popular Player | Cord Cutters News
Sony has discontinued its final standalone UHD Blu-ray player, the UBP-X700/K, ending shipments of the device with no successor model announced. The move, first spotted by Japanese website Kunkoku.jp and confirmed through the status of the product on Sony’s own website, marks the company’s...
cordcuttersnews.com
I am so done with Sony on so many levels. This is just one small piece of it.Sony is discontinuing it's last 4K disc player, Panasonic has been rumored to be doing the same, the end of physical media is unfortunately, about to happen.
Bad News For Blu-ray Fans: Sony Has Stopped Making a Popular Player | Cord Cutters News
Sony has discontinued its final standalone UHD Blu-ray player, the UBP-X700/K, ending shipments of the device with no successor model announced. The move, first spotted by Japanese website Kunkoku.jp and confirmed through the status of the product on Sony’s own website, marks the company’s...
I Love my Sony equipment
Why are ViP922s So rare? like its crazy how ebay has none, i checked everywhere, also, i got a ViP222k now, which is actually activated!
28 Replies
·
706 views
LOL. It depends if the person saw it during the years when they were actually still available which is 1968 to 1983 meaning the person could be 43-58 years old or they can even be a few years old if they learned to read and write at a young age and actually saw a telephone with that label somewhere recently just like even here in San Francisco, payphone still exist physically in public places but whether they can be used or not is a different issue. It still looks like this even today:
S
so that persons in hiding lol
I remember this in the news too...
www.nbcnews.com
$14,000 spent on rented rotary phone
A widow rented a rotary dial telephone for 42 years, paying what her family calculates as more than $14,000 for a now- outdated phone.
www.nbcnews.com
That is a misnomer. In the old days you subscribed to telephone service. That included the telephone line and one telephone. An extension cost $1 a month extra. So that $14,000 over 42 years was for the service not the leased telephone. There is no way they paid $28 a month for 42 years for a leased telephone.I remember this in the news too...
$14,000 spent on rented rotary phone
A widow rented a rotary dial telephone for 42 years, paying what her family calculates as more than $14,000 for a now- outdated phone.
Howdy folks long time no write.
Issue(s): Horizontal transponders (esp. Weigel mux) breakup/mosaic/sputtering audio, JTV less so (but received perfectly up until a month or so ago.
Vertical is fine (Daystar). Up until recently couldn't even get any signal on Weigel Mux but JTV was perfect.
What I did to improve things: A slight westward move improved reception but only slightly (approx 72 on the micro HD, sorry no dB to post). I removed the 3-way C-Band splitter and used a 2-way to get a 1-2 db signal gain ( the power port goes to the Startrak - the micro HD doesn't have enough juice ! (1st clue) even after swapping the switching power supply it came with with a heftier linear 12 V supply (less RFI too !).
I have had issues with the uHD before signal breaking up that a reboot would clear up (clue #2 = dying tuner?) - FYI, I reinforced the IF input and removed all flux from the pcb completely with a Flux Removal Pen (MG Chemicals Cat No. 4140-P) which definitely makes a huge difference.
I went outside and pushed and pulled reflector slightly and no improvement. Pole (actually tower in yard - the neighbours love me..NOT) is plumb, checked with carpenters level. Dish was last peaked in 2017 or so, after overhauling 24" Von Weise, new Acme, fresh grease, etc. Focal length, f/d ratio etc meticulously adjusted. One panel has a tear so planning to repair that this weekend when my cousin comes over ( to help me out (old guy here) forecast calls for sunshine.
What has changed: My utility company has installed new high tension line poles (one smack dab in the middle of 101°W target! But they put it in last year and reception (of JTV (HOR) at least) was fine, BUT when they came out to transfer the wires over this year from the old (sawed in half) pole that's about when the troubles started (coincidence?), but again Daystar (VER) was fine. I always had this pole in the light of sight of 101° before with no issues. (fyi my zenith sat 74° is unobstucted, but can't test)
In the meantime Weigel mux is trying to break in MOSTLY in LATE at night (less cell usage?) (audio not video except for a frame here or there) so don't know what has changed with this mux which suddenly "woke up". I have never had to fuss with dish moves on this satellite ( the slightest move +/- motor clicks loses lock, wheres normally on C-band I can go significantly wider east or west and still have a strong signal ( have these gone "spot beam" or narrower somehow and what is the slight difference in Az listed on Lyngsat to 100.9° affect things ( isn't that the declination i.e. requiring a tweak of declination?).
Long story short (too late, ha), if I had another DVB-S2 box to try and / or a newer more stable PLL lnb ( I have been meaning to upgrade many a time but never got arround to it) I could determine if it's my antiquated receiving equipment, or my dish/feed alignment ( doubtful as it tracks everything from 55 °W to 133 ° W nicely.) or the dreaded 5G! (BUT only on HOR and not VER?).
I read another post where the OP (with his smaller 7.5 footer) played around with the illumination to peak desired transponder and reduce qrm on interfering/ stronger xpndrs (even on 103° W). So will play with that too - and cut away the RG-6 a and pull up a fresh section with new PPC and coax Seal. Open the throat cap see if any cobwebs are there and check servo operation (also changed in last maintence 10 years ago).
Finally, this will probably be the last chance I get to play with the BUD from the looks of it (providers leaving, auctioning off rest of spectrum imminent above 4.0 Ghz, and to keep the peace with neighbours so it would be nice to have that mux back for the long, cold and dark winters to comfort this old man before I call it quits and buy a VHF/UHF/FM Yagi and get MeTV, H&I from my Vermont local stations (checked at a friends today and they come in nicely - except ABC) .
Only one guy in town (Montreal) I may be able to get a receiver or PLL lnb from to try (RPS Sat) so hopefully with elimnate that as a possible culprit. Be nice to pick up a cheap or used PLL lnb to try w/o 5G BPF (money is tight )
Like others I couldn't care less about "tv" (well maybe just a liitle or a lot) it's the challenge that excites me , I can get MeTV other ways OTA (no pirate crap).
So what do you guys (and gals) think ?. p.s. I don't have a spectrum analyzer and there are def/ cell towers nearby (half a Km or so away).
Oh and time permitting will hammer out dings too and wire damaged mesh on one section for an extra dB or two. Hesitate to touch Declination, Elevation and pole mount but will play around with those a little too... Why is this mux for finicky suddenly ?(8psk, 5/6 fec, beamwidthetc.. man wish they went back to VER I think everthing would be fine! For the engineers out here does 5G QRM affect one poliarization (HOR) more than another (VER)? I understand the strong interference swamps out the input mixer/local oscilator in the hapless old C-band lnb (I think it at time affect KU too esp. LPB on 101°W KU - incidentally thos were weak or "gone' but are back almost at the time MeTV improved..hmm Terrestrial interference?
Any thoughts or suggestions ( cheap or free solutions please) greatly appreciated. Cheers.
p.p.s. Micro HD can't display Decades and Toons but records them fine so I can watch on another box/media player (Ali chip set issue). Another reason to upgrade.
Anybody interested in a nice C/KU system free ? (for next Spring/Summer 2027)
[Sami 10' mesh, Corotor II+, Eagle Aspen (very old) C-band lnb, Norsat Ku lnb, Channel Master C/Ku (H/V) switch, Startrak 400 Analog receiver w/ motor control, Geosat uHD DVD-S2, CW600S for Mpeg-2]
Issue(s): Horizontal transponders (esp. Weigel mux) breakup/mosaic/sputtering audio, JTV less so (but received perfectly up until a month or so ago.
Vertical is fine (Daystar). Up until recently couldn't even get any signal on Weigel Mux but JTV was perfect.
What I did to improve things: A slight westward move improved reception but only slightly (approx 72 on the micro HD, sorry no dB to post). I removed the 3-way C-Band splitter and used a 2-way to get a 1-2 db signal gain ( the power port goes to the Startrak - the micro HD doesn't have enough juice ! (1st clue) even after swapping the switching power supply it came with with a heftier linear 12 V supply (less RFI too !).
I have had issues with the uHD before signal breaking up that a reboot would clear up (clue #2 = dying tuner?) - FYI, I reinforced the IF input and removed all flux from the pcb completely with a Flux Removal Pen (MG Chemicals Cat No. 4140-P) which definitely makes a huge difference.
I went outside and pushed and pulled reflector slightly and no improvement. Pole (actually tower in yard - the neighbours love me..NOT) is plumb, checked with carpenters level. Dish was last peaked in 2017 or so, after overhauling 24" Von Weise, new Acme, fresh grease, etc. Focal length, f/d ratio etc meticulously adjusted. One panel has a tear so planning to repair that this weekend when my cousin comes over ( to help me out (old guy here) forecast calls for sunshine.
What has changed: My utility company has installed new high tension line poles (one smack dab in the middle of 101°W target! But they put it in last year and reception (of JTV (HOR) at least) was fine, BUT when they came out to transfer the wires over this year from the old (sawed in half) pole that's about when the troubles started (coincidence?), but again Daystar (VER) was fine. I always had this pole in the light of sight of 101° before with no issues. (fyi my zenith sat 74° is unobstucted, but can't test)
In the meantime Weigel mux is trying to break in MOSTLY in LATE at night (less cell usage?) (audio not video except for a frame here or there) so don't know what has changed with this mux which suddenly "woke up". I have never had to fuss with dish moves on this satellite ( the slightest move +/- motor clicks loses lock, wheres normally on C-band I can go significantly wider east or west and still have a strong signal ( have these gone "spot beam" or narrower somehow and what is the slight difference in Az listed on Lyngsat to 100.9° affect things ( isn't that the declination i.e. requiring a tweak of declination?).
Long story short (too late, ha), if I had another DVB-S2 box to try and / or a newer more stable PLL lnb ( I have been meaning to upgrade many a time but never got arround to it) I could determine if it's my antiquated receiving equipment, or my dish/feed alignment ( doubtful as it tracks everything from 55 °W to 133 ° W nicely.) or the dreaded 5G! (BUT only on HOR and not VER?).
I read another post where the OP (with his smaller 7.5 footer) played around with the illumination to peak desired transponder and reduce qrm on interfering/ stronger xpndrs (even on 103° W). So will play with that too - and cut away the RG-6 a and pull up a fresh section with new PPC and coax Seal. Open the throat cap see if any cobwebs are there and check servo operation (also changed in last maintence 10 years ago).
Finally, this will probably be the last chance I get to play with the BUD from the looks of it (providers leaving, auctioning off rest of spectrum imminent above 4.0 Ghz, and to keep the peace with neighbours so it would be nice to have that mux back for the long, cold and dark winters to comfort this old man before I call it quits and buy a VHF/UHF/FM Yagi and get MeTV, H&I from my Vermont local stations (checked at a friends today and they come in nicely - except ABC) .
Only one guy in town (Montreal) I may be able to get a receiver or PLL lnb from to try (RPS Sat) so hopefully with elimnate that as a possible culprit. Be nice to pick up a cheap or used PLL lnb to try w/o 5G BPF (money is tight )
Like others I couldn't care less about "tv" (well maybe just a liitle or a lot) it's the challenge that excites me , I can get MeTV other ways OTA (no pirate crap).
So what do you guys (and gals) think ?. p.s. I don't have a spectrum analyzer and there are def/ cell towers nearby (half a Km or so away).
Oh and time permitting will hammer out dings too and wire damaged mesh on one section for an extra dB or two. Hesitate to touch Declination, Elevation and pole mount but will play around with those a little too... Why is this mux for finicky suddenly ?(8psk, 5/6 fec, beamwidthetc.. man wish they went back to VER I think everthing would be fine! For the engineers out here does 5G QRM affect one poliarization (HOR) more than another (VER)? I understand the strong interference swamps out the input mixer/local oscilator in the hapless old C-band lnb (I think it at time affect KU too esp. LPB on 101°W KU - incidentally thos were weak or "gone' but are back almost at the time MeTV improved..hmm Terrestrial interference?
Any thoughts or suggestions ( cheap or free solutions please) greatly appreciated. Cheers.
p.p.s. Micro HD can't display Decades and Toons but records them fine so I can watch on another box/media player (Ali chip set issue). Another reason to upgrade.
Anybody interested in a nice C/KU system free ? (for next Spring/Summer 2027)
[Sami 10' mesh, Corotor II+, Eagle Aspen (very old) C-band lnb, Norsat Ku lnb, Channel Master C/Ku (H/V) switch, Startrak 400 Analog receiver w/ motor control, Geosat uHD DVD-S2, CW600S for Mpeg-2]
12 Replies
·
466 views
Staff member
HERE TO HELP YOU!
Cutting Edge
Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!
So let the game continue!
The last song was added by Bobby who posted...
One Meat Ball - Andrews Sisters
CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!
Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game
Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.
Example:
Long Live Rock and Roll -- Rainbow
Rainbow in the Dark -- Dio
Another example:
Ride the Lightning -- Metallica
Lightning Strikes -- Ozzy Osbourne
Get it?
An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
So let the game continue!
The last song was added by Bobby who posted...
One Meat Ball - Andrews Sisters
CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!
Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game
Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.
Example:
Long Live Rock and Roll -- Rainbow
Rainbow in the Dark -- Dio
Another example:
Ride the Lightning -- Metallica
Lightning Strikes -- Ozzy Osbourne
Get it?
An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
68576 Replies
·
2675949 views
For some reason, the satelliteguys.us site is loading a lot slower than usual on both Chrome on my Asus laptop and Safari on my iPhone.
I'm also seeing longer appearances of the blue bar at the top and the "3 blue bars" loading symbol.
Is anyone else also having the same problem? Thanks in advance.
I'm also seeing longer appearances of the blue bar at the top and the "3 blue bars" loading symbol.
Is anyone else also having the same problem? Thanks in advance.
551 Replies
·
19090 views
More specifically, these:
A more scholarly story is here:
www.bleepingcomputer.com
A more scholarly story is here:
PHP warns admins of two critical flaws, emergency patches coming tomorrow
The PHP security team is warning administrators to prepare for emergency security updates tomorrow to address two critical vulnerabilities, as information about the flaws has reportedly leaked ahead of their scheduled disclosure.
When I heard about this exploit I was wondering how quick you would be on it.
12 minutes after the patch was release I had it patched.When I heard about this exploit I was wondering how quick you would be on it.
Pub Member / Supporter
Now that I'm retired, obviously I have different health care insurance. I take 2 prescriptions. With my old insurance I didn't have to pay for either of them, now I do. It's not a huge amount but it led me to dig a little into the cost of prescription medications. I have been using Walgreens for the longest time. But what I found was that Walgreens price is 4.8 times more for one of my prescriptions and the other is 2.3 percent more compared to the lowest price pharmacy. If you pay for prescription medications you might want to have a look at trumprx and see if you can get a lower price.
8 Replies
·
51 views
M
I'm lucky. I have half a dozen pills and Continuous Glucose Monitor (diabetic) and it's all covered
On my old plan (different job) the pills cost about $100 for 90 days and couldn't get the CGM. Insurance wouldn't give a discount.
On my old plan (different job) the pills cost about $100 for 90 days and couldn't get the CGM. Insurance wouldn't give a discount.
Lon.TV
Time for another AWESOME video from Lon Seidman of LON.TV!
View: https://www.youtube.com/watch?v=JhwivKnNZrw
Direct YouTube Link - Lithium UPS Battery Backup Review - Oupes UPS 1200 Review
The Official LON.TV Website
Lon on Facebook
View: https://www.youtube.com/watch?v=JhwivKnNZrw
Direct YouTube Link - Lithium UPS Battery Backup Review - Oupes UPS 1200 Review
The Official LON.TV Website
Lon on Facebook
0 Replies
·
8 views
My OTA is not working anymore. This started after the latest update. I have the OTA dongle with a OTA antenna that I've been using for years. My hopper does not recognize the dongle anymore and when I go to the OTA setting, it has a screen that says to plug a dongle into the USB. I tried unplugging and plugging back, in the same usb port and other ports. The Hopper does not recognize it. Anyone have same issue?
202 Replies
·
5282 views
Hi all. If you were using a single tuner USB OTA adapter that is no longer working, please PM me. Thanks.
Staff member
HERE TO HELP YOU!
9 Replies
·
88 views
TWiT Tech Podcast Network
Time for another AWESOME video from the TWIT Network!
View: https://www.youtube.com/shorts/xnM_6NlEjsU
Direct YouTube Link - iPhone Duo Preorder Experience With Christina Warren
TWIT's Website
TWIT Live Feed
View: https://www.youtube.com/shorts/xnM_6NlEjsU
Direct YouTube Link - iPhone Duo Preorder Experience With Christina Warren
TWIT's Website
TWIT Live Feed
0 Replies
·
7 views