Social Feed

G
Last reply · posted in C-BAND Satellite Discussion
My dish install is on hold, waiting on family members to help me put the 10 footer on the mount, so I started thinking about how I am going to get the cable from the dish to the house. I am also going to put a motorized Primestar near the bud. I have been dreading digging a trench deep enough for conduit, and I knew that I got a piece of ribbon cable when I picked up the dish. I thought that it might be about 40', but was surprised after rolling it out that it was 100'. That was good news, but I finally measured how much cable I need to get from the receiver to the dish and I need about 150'. Is it feasible to splice the control wires to sprinkler cable & connect 2 rg6 cables to the 2 coax cables in the ribbon cable to make up the difference? Of course the connections would be put in weather proof boxes. I'm not worried about the control wires, but would the bullet connections on the rg6 insert too much loss?
11 Replies · 2180 views
G
Calsulfide, thanks again for the reply. I will be using the ribbon cable temporarily on the ground for sure. Home Depot has a walk behind trencher for $150 a day and I've priced out conduit, elbows, sprinkler wire (longest I found was 100'), so that wouldn't be an option if I want a full run. I'd like to avoid spending the money on a trencher if I can. Of course, it might be a bargain, if I hurt my back using a pick and shovel. Anyway, any and all suggestions are welcome. Not sure about the motor sensor wires yet. From another thread, some folks seem satisfied with sprinkler wire and others say you need shielded wires to avoid pulse count errors.

jgbalyless, thanks for the input & yes I plan on using a visionsat IV200, that I just purchased (should be here tuesday). I'm going to use a Houston Tracker 9, to move the dish. Came with the dish. I'm keeping ku separate on a motorized dish. The only fixed dish that I will have is for Hispasat (for baseball). I have to keep that one on the chimney stack. No los from where I will be putting the motorized primestar. Hopefully by late summer, maybe a 4dtv sub or w5 package. Just want to get the free cband first. This project is going to take a while, just can't seem to stay home long enough to make any progress.
phlatwound
If the soil isn't too rocky I've used a tiller for trenching.

Just remove the outside tines so you are just using the 2 inner ones, depending on the tiller it should get you a trench about a foot wide and 8" deep, or so.

You still have to use a shovel to remove the loosened dirt, but it takes most of the heavy work away.
G
phlatwound, My wife has been suggesting that I try my son-in-law's Poulan tiller. I told her it would dig up too much of the yard. Never thought, that I might be able to take off the outside tines. That might be the answer. I'll check into that. I do have a lot of rocks, but when I built my house, I used a 4 ft tiller mounted on the back of my tractor to loosen some of the surface rocks and it worked good to get the ground ready for grass. It's solid limestone about 18" down. Thanks
Cadsulfide
Glater;

If you have a tractor, just use one cultivator shovel on the 3 point to dig the trench. As long as the pipe is well below the sod (8"), it shouldn't frost heave. Consider pulling a run of CAT5 for the sensor wires in addition to the sprinkler wire for motor drive. That will allow for all kinds of future additions.
G
Cadsulfide, all I have now is a small Kubota14hp tractor with turf tires. It won't pull a cultivator shovel. I bought a middle buster for my old 40hp tractor when I bought this property to try to dig a trench for electricity to my well pump. Didn't even scratch the surface. One thing I don't have to worry about is the frost line. Our year round average temperature is about 75 degrees. Only gets into the mid 20's a couple of times a year. cat5 is a good option. Wish I'd have got some when I worked at the phone company. When our contractors mined cables, there were always long runs of cat5 in the dumpsters. Been retired too long, so no contacts there. Thanks again.
meStevo
Lifetime Supporter
Last reply · posted in The Chit Chat Club
Continuing the Kilauea thread in the Pub here. Perhaps the Iceland one too next time there's remarkable activity.

Currently there is precursory lava flowing into the crater, leading to the next episode that'll probably start within the next day.

You can see the pace of inflation / deflation here. It serves as the primary predictor for when the expect the eruptions, which coincide w/ inflation turning into significant deflation and last for several hours on average with significant fountaining.



View: https://youtu.be/Uecu2seh4b4


Wife and I like the AfarTV feeds, for the discussion along w/ them, though they're otherwise just mirrors of the official USGS feeds.


View: https://youtu.be/iws3rh5vLAQ
124 Replies · 3692 views
  • Like
Reactions: osu1991
Foxbat
Looks like Episode 55 is over at 09:00 HST, just under six hours. The USGS said the fountains reached 720' or 220 meters.
​
  • Like
Reactions: RaiderPower
Foxbat
The USGS Kīlaeua Webcam #1 has been showing overflows and doming from the North vent overnight. Maybe the volcanic plumbing has settled back into its two-three week cycle of fountaining?

But I do miss the little cinder cone that broke up in the last episode.
Foxbat
Sorry, I should have posted these earlier:

​

We're still waiting on the start of Episode 56.
  • Like
Reactions: RaiderPower
Foxbat
At 08:01 HST 11/05/2026, the North Vent produced what I would call a "wet burp" after the precursory "pistoning" events, small amounts of lava pouring out of the vent for a few seconds to minutes and then everything recedes. There must have been a gas bubble holding thing back because two minutes later the lava started flowing out of the vent in all directions. Then, at 08:25, it stopped. What a tease! I thought this was how Episode 56 started.

About 12 minutes later at 08:38, the North vent once again started overflowing and picked up steam at 08:42. By 09:00, slight doming could be seen in the pool of lava in the vent. Surely this is it!

But, 09:50 and things wind down again. By 09:57 HST there's just fumes coming out of the vent. Phooey.

But then 10:00 comes and the heavy lava flows kick in again. This time seems like the real deal. At 10:30 HST there's little spurts of lava flying up in the air over the vent, but more from gas than a steady fountain of lava. This looks promising!

11:30 HST and the color of the lava is definitely hotter, and the intensity has picked up to a definite dome and precursor to fountaining. The USGS calls Episode 56 as officially starting at 12:10 HST:

Alert Level: WATCH, Color Code: ORANGE 2026-11-05 22:29:12 UTC
HVO/USGS Volcanic Activity Notice

Volcano: Kilauea (VNUM #332010)

Current Volcano Alert Level: WATCH
Current Aviation Color Code: ORANGE

Issued: Thursday, November 5, 2026, 12:29 PM HST
Source: Hawaiian Volcano Observatory
Notice Number: 2026/H514
Location: N 19 deg 25 min W 155 deg 17 min
Elevation: 4091 ft (1247 m)
Area: Hawaii

Summary: Episode 56 of the ongoing Halemaʻumaʻu eruption began at 12:10 PM HST on November 5, 2026.

Volcanic Activity:
Episode 56 of lava fountaining in Halemaʻumaʻu began at the summit of Kīlauea began at 12:10 PM HST on November 5, 2026.

Lava fountain heights are relatively low at about 100 ft (30 meters), but will likely increase. Ground-level sensors near the eruptive vents indicate that winds are blowing from the northeast direction, which suggests that volcanic gas emissions and volcanic material may be distributed to the southwest direction from Halemaʻumaʻu.
  • Like
Reactions: meStevo
Foxbat
​
BlackHitachi
Supporting Founder
Last reply · posted in Movie Talk
Since the Reds have there thread we should too!

Last watched Nine inch Nails
Next 3:10 to Yuma
5397 Replies · 511765 views
dfergie

Last of the Dogmen is my favorite of hers.
  • Like
Reactions: osu1991
"MysteryMan"
Gone.webp
osu1991
Star Wars Despecialized Edition

IMG_0803.webp
dishstaller
Just watched Napoleon. Good night.....all of those young men dying for the egos of their leaders. Now we can kill at a distance, back then you saw the man you were killing eye to eye.
comfortably_numb
Pub Member / Supporter
Last reply · posted in Internet Television (IPTV) Discussion Forum
Not sure saving $24/year is worth it unless you're a hardcore Philo user. I'll stick with monthly.

IMG_0351.webp
7 Replies · 228 views
Jimbo
Not sure saving $24/year is worth it unless you're a hardcore Philo user. I'll stick with monthly.

View attachment 195247
$24 for the Year, would be more useful.
Howard Simmons
$24 for the Year, would be more useful.
But when you cancel you still have to watch until the plan runs out. With monthly you're done at the end of the month.
Jimbo
But when you cancel you still have to watch until the plan runs out. With monthly you're done at the end of the month.
Sorry, my point was the expense.
comfortably_numb
$24 for the Year, would be more useful.

Philo's monthly price is reasonable, IMO, because it's still the cheapest way I'm aware of to get all the linear Discovery networks AND access to the Discovery Go apps.
  • Like
Reactions: Howard Simmons
Jimbo
Philo's monthly price is reasonable, IMO, because it's still the cheapest way I'm aware of to get all the linear Discovery networks AND access to the Discovery Go apps.
I guess if it was something I used on a regular basis, I suppose.
  • Like
Reactions: Howard Simmons
comfortably_numb
In other Philo news..

IMG_0364.webp
Bobby
Oh boy, I can't wait! 😂
K
Pub Member / Supporter Lifetime Supporter
Last reply · posted in TV Shows
'Rockford Files' Reboot Gets NBC Pilot Order

I grow tired of all the reboots. Most I don't bother with but will depend on the actor chosen.
19 Replies · 753 views
long_time_Dish
Yeah, I'll check it out as well, but shan't be holding my breath...It'll be tough to equal James Garner in that role...
  • Like
Reactions: Foxbat
harshness
...It'll be tough to equal James Garner in that role...
I can think of a few actors (including some females) who might fit the bill.

This will all depend on the storyline. I'm not sure how well it will translate. Modern TV hasn't been all that kind to PIs and even less kind to CIs (confidential informants).
K
Premier is Saturday, Jan 2nd. Moving to Thursday on the 7th.
long_time_Dish

I wonder how they're/if they're going to do something like the answering machine message opening? It was always funny...
  • Like
Reactions: dfergie
osu1991
Pub Member / Supporter
· posted in Movie Talk
0 Replies · 21 views
  • Like
Reactions: Foxbat and dfergie
osu1991
Pub Member / Supporter
· posted in Movie Talk
0 Replies · 26 views
  • Like
Reactions: Foxbat
M
Last reply · posted in DISH Network Support Forum
I have Dish with Hopper3. I choose to get local channels OTA and had a "guide list" established at my previous home. Having moved a few miles away, I wanted to update the list by appending a couple new stations via a rescan. As many would know, some stations come in with the UHF/VHF antenna aimed in one direction, while others come in better with a different direction.

Unfortunately, when a scan is done (bringing in 25-30 stations for that particular antenna aim), the dialog screen does not present the established guide list; it presents an empty field to the right that the scanned stations may be selected one by one and added to the empty guide. But because of antenna aim, some stations originally saved are missing, and would have to be retrieved with a different antenna aim. But as I explain, if a 2nd​ scan is done with a different antenna aim, the stations saved from the first scan are lost.

It troubles me that Dish didn't develop software that would allow a user to simply append only 1 or 2 channels to the established list. :mad:

Any thought on this? Has anyone experienced this or heard of this from others?
15 Replies · 515 views
dishstaller
I could very well be wrong....it has been a LOT of years but back when I had a 722K it seemed like when you went back to the scan screen that you could just scan again and it would ADD those channels to the previous list or you could delete the previous results and only add the channels from the new scan.
  • Like
Reactions: charlesrshell
N
I could very well be wrong....it has been a LOT of years but back when I had a 722K it seemed like when you went back to the scan screen that you could just scan again and it would ADD those channels to the previous list or you could delete the previous results and only add the channels from the new scan.
I am not sure about that but I do know that you could manually add additional channels just by entering the actual RF channel number and the older receivers would add the virtual channels to your list
dishstaller
I am not sure about that but I do know that you could manually add additional channels just by entering the actual RF channel number and the older receivers would add the virtual channels to your list
Like I said.....that has been many years ago. Swapped my 722K for a Hopper in 2012.

It does seem like I remember having to delete the existing channels when we did a rescan. Back then our local stations KEPT monkeying around with things and it was non-stop complaints from customers about their channels not coming in. Got so bad that I stopped selling OR installing OTAs....something I had been doing since 1984 so you know it HAD to be pretty bad.
M
You made one of my points for me with this comment, Dishstaller:

"... local stations KEPT monkeying around with things and it was non-stop complaints from customers about their channels not coming in ..."
dennispap
I could very well be wrong....it has been a LOT of years but back when I had a 722K it seemed like when you went back to the scan screen that you could just scan again and it would ADD those channels to the previous list or you could delete the previous results and only add the channels from the new scan.
I remember that also on my 722.
dishstaller
I remember that also on my 722.
Thanks.....has been too many years to remember clearly.
  • Like
Reactions: charlesrshell
Bobby
Keep in mind that the 722 had a built in OTA tuner and the 722K had a plug in module for OTA. The Hoppers and Wallys use an add on USB OTA dongle. I believe they are entirely different.
Linus Tech Tips
· posted in Linus Tech Tips
0 Replies · 20 views
osu1991
Pub Member / Supporter
Last reply · posted in TV Shows
12 Replies · 257 views
osu1991
Finished the 2nd episode tonight. I'm really liking it so far.

Still hate weekly releases though, especially the way Disney and HBO do it waiting until 8pm to premiere it.
Foxbat
Apparently I'm not a big enough nerd🤓 since I did not read every Marvel Comic Book ever published. If I had, I might be comparing the comics' version of events compared to what's transpiring in "Visionquest". So, I am enjoying the series a lot, not weighed down by previous expectations, knowing only the Avengers MCU movies and the "Wandavision" / "Agatha All Along" TV series.

I found the Mr Know-it-All channel from his discussion about "Star Trek: Strange New Worlds" and he's been gleefully picking these episodes apart, referencing the Marvel comics from the 1939 on. Turns out A.I. has been around since before World War II, at least in the comics. (Robots before that, yes, yes.) This show is going back into the archives.
  • Like
Reactions: osu1991
Foxbat
I'm expecting the finale to basically bring Vision into play for the Doomsday movie next month.
  • Like
Reactions: osu1991
osu1991
annoying they went with single episodes for the last two after releasing two a week for the first 3 weeks
Foxbat
annoying they went with single episodes for the last two after releasing two a week for the first 3 weeks
I thought they were effectively releasing a longer episode 7 and 8 instead of shorter episodes 7 & 8 this week and 9 & 10 next week. It felt like they were packing more into this episode.

edit: But you're right, the run time of the first three pairs of episodes was 100 minutes on average. Episode 7 clocks in at 65 minutes. 😕