Social Feed

yourbeliefs
Pub Member / Supporter
Last reply · posted in DIRECTV General Forum
As I seem to do every 4th quarter of the year, I am planning on moving once again, and since the cable company where I'll be moving to (Raoul, you can attest to this) is crap, it looks like the big old 5-lnb will be coming as well. The problem is that the building I'm moving into, an old 19th century Victorian house, has had numerous issues with the roof, and I'm not big on throwing this big dish on the roof and causing problems. I know I can install a dish outside of the roof such as on a rod, but I'm not sure of the ramifications of doing that in terms of reception quality and so on. Is there any sort of prep work I can do before involving D* to help ensure that a non-roof installation is A: Possible and B: Can be installed optimally?
40 Replies · 7387 views
B
Wow! That babies really up there....haha That has to sway with a little wind. Our poles are 6ft long with three feet in the ground. If you dont feel like cementing it there is another option. You can use an old footing from an old mount and fasten it to the bottom of the pole with 2 screws. I doubt you have any footings laying around but that is an option. I sometimes use this method when I run out of cement.


btw: if you decide to mount the pole yourself dont forget to flatten the bottom of the pole to prevent it from turning.
raoul5788
Wow! That babies really up there....haha That has to sway with a little wind. Our poles are 6ft long with three feet in the ground. If you dont feel like cementing it there is another option. You can use an old footing from an old mount and fasten it to the bottom of the pole with 2 screws. I doubt you have any footings laying around but that is an option. I sometimes use this method when I run out of cement.


btw: if you decide to mount the pole yourself dont forget to flatten the bottom of the pole to prevent it from turning.

I did the install myself. It's a 12 ft pole with about 3.5 ft in the ground. I used two 50# bags of Quikrete, and there is a thru bolt in the bottom. I have NEVER lost reception in any wind, and that includes wind gusts up to 70 mph. It's been there for over four years. Any other comments?
B
I did the install myself. It's a 12 ft pole with about 3.5 ft in the ground. I used two 50# bags of Quikrete, and there is a thru bolt in the bottom. I have NEVER lost reception in any wind, and that includes wind gusts up to 70 mph. It's been there for over four years. Any other comments?
Since your going to get pissy about it then no. I cant tell what your line of sight looks like so I cant tell if the 16 footer was necessary....I'm sure it was.
raoul5788
Since your going to get pissy about it then no. I cant tell what your line of sight looks like so I cant tell if the 16 footer was necessary....I'm sure it was.

Pissy? Sure. :rolleyes: You make snide comments on my install that you know nothing of, you are going to get attitude from me. If you act like an adult you will get respect. Of course I needed the height because of los reasons. It wasn't a 16 ft pole, it was 12. Can you read? There is about 8.5 ft above ground.
B
Pissy? Sure. :rolleyes: You make snide comments on my install that you know nothing of, you are going to get attitude from me. If you act like an adult you will get respect. Of course I needed the height because of los reasons. It wasn't a 16 ft pole, it was 12. Can you read? There is about 8.5 ft above ground.
I'm hearing that maybe you are a little too uptight. I said that it must sway with wind, you said it has NEVER EVER EVER lost a signal. 70 mph winds?? OK maybe a newbie will believe that but I know better. I guess you have a slimline dish 8.5 ft on top of pole with no sway? You know what, your right, I should never doubt an expert on pole mounts like yourself. The PMS in this place has gotten outta control. Sorry to OP for getting thread hijacked
raoul5788
I'm hearing that maybe you are a little too uptight. I said that it must sway with wind, you said it has NEVER EVER EVER lost a signal. 70 mph winds?? OK maybe a newbie will believe that but I know better. I guess you have a slimline dish 8.5 ft on top of pole with no sway? You know what, your right, I should never doubt an expert on pole mounts like yourself. The PMS in this place has gotten outta control. Sorry to OP for getting thread hijacked

You are a newbie. Enough said!
yourbeliefs
Update: I talked to the landlord (AKA my Dad) and he informed me that the problems on the roof were isolated to only the flat roof above the entrance way, meaning that he has no issue with me doing a regular roof install anywhere BUT there. I think I am going to go that route as a result. Thanks for all the info everyone..

and please stop fighting! If the setup works then it is correct. End of story. YMMV
B
I'd rather that you did ask me to leave because I'd never use a 16ft pole......besides if it is supported at the roof with only 4ft past the roof then it is a little different then just sticking a 12ft pole in the ground....
Jimbo
I'd rather that you did ask me to leave because I'd never use a 16ft pole......besides if it is supported at the roof with only 4ft past the roof then it is a little different then just sticking a 12ft pole in the ground....

Agreed.
Of course, I would never expect a D* contractor or otherwise to install a pole of that length.
Can't imagine what they would charge for THAT install.

I know what it cost me for everything, it was under $ 50 plus my time of course.

I also placed it where I have a flat roof to work off of ....AND it's not seen at the street !
yourbeliefs
Final update on this.

So the install was scheduled for today. The guy came out (actually arrived nearly an hour early) and said he wasn't sure where he could put the dish. After a bunch of walking around we determined that it was basically impossible to install it on the actual building (there's a ton of trees in the LOS) and instead we had to install it on a barn that was on the property and have to hang a line between the buildings. This wasn't even considering the issues we had getting wires into the actual building, since we don't have a lot of walls in our apartment (it was originally an office, not a residential.) We agreed to try that and the guy said his supervisor would get back to me. During that time I had a little soul searching and looked into how much getting cable would cost. After figuring out that Cable vs D* was about the same a month, and out of respect for my father's building and property, I decided to jump back to cable and cancel D* after this billing month, assuming no problems with the cable.

All things being equal I would definitely keep D*, but seeing as it's my dad's building and he was only tolerating the IDEA of a dish because I'm his son, I think I just have to suck it up and go on an indefinite DirecTV hiatus. Once I get my own place again (or someone else's building who I don't give a crap about) I'll definitely look at D* again.
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in The Chit Chat Club
Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne


Get it?


An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
68542 Replies · 2673865 views
  • Like
Reactions: c-spand
H
LITTLE Willy-Sweet
  • Like
Reactions: ClarkGable
ClarkGable
Little Deuce Coupe - The Beach Boys
  • Like
Reactions: gms49ers
gms49ers
The Boys of Summer - Don Henley
FTA4PA
Summer In The City - The Lovin' Spoonful
Bobby
Gonna Send You Back To Georgia (A City Slick) - Timmy Shaw
T
Last reply · posted in C-BAND Satellite Discussion
Howdy folks long time no write.

Issue(s): Horizontal transponders (esp. Weigel mux) breakup/mosaic/sputtering audio, JTV less so (but received perfectly up until a month or so ago.
Vertical is fine (Daystar). Up until recently couldn't even get any signal on Weigel Mux but JTV was perfect.

What I did to improve things: A slight westward move improved reception but only slightly (approx 72 on the micro HD, sorry no dB to post). I removed the 3-way C-Band splitter and used a 2-way to get a 1-2 db signal gain ( the power port goes to the Startrak - the micro HD doesn't have enough juice ! (1st clue) even after swapping the switching power supply it came with with a heftier linear 12 V supply (less RFI too !).
I have had issues with the uHD before signal breaking up that a reboot would clear up (clue #2 = dying tuner?) - FYI, I reinforced the IF input and removed all flux from the pcb completely with a Flux Removal Pen (MG Chemicals Cat No. 4140-P) which definitely makes a huge difference.

I went outside and pushed and pulled reflector slightly and no improvement. Pole (actually tower in yard - the neighbours love me..NOT) is plumb, checked with carpenters level. Dish was last peaked in 2017 or so, after overhauling 24" Von Weise, new Acme, fresh grease, etc. Focal length, f/d ratio etc meticulously adjusted. One panel has a tear so planning to repair that this weekend when my cousin comes over ( to help me out (old guy here) forecast calls for sunshine.

What has changed: My utility company has installed new high tension line poles (one smack dab in the middle of 101°W target! But they put it in last year and reception (of JTV (HOR) at least) was fine, BUT when they came out to transfer the wires over this year from the old (sawed in half) pole that's about when the troubles started (coincidence?), but again Daystar (VER) was fine. I always had this pole in the light of sight of 101° before with no issues. (fyi my zenith sat 74° is unobstucted, but can't test)

In the meantime Weigel mux is trying to break in MOSTLY in LATE at night (less cell usage?) (audio not video except for a frame here or there) so don't know what has changed with this mux which suddenly "woke up". I have never had to fuss with dish moves on this satellite ( the slightest move +/- motor clicks loses lock, wheres normally on C-band I can go significantly wider east or west and still have a strong signal ( have these gone "spot beam" or narrower somehow and what is the slight difference in Az listed on Lyngsat to 100.9° affect things ( isn't that the declination i.e. requiring a tweak of declination?).

Long story short (too late, ha), if I had another DVB-S2 box to try and / or a newer more stable PLL lnb ( I have been meaning to upgrade many a time but never got arround to it) I could determine if it's my antiquated receiving equipment, or my dish/feed alignment ( doubtful as it tracks everything from 55 °W to 133 ° W nicely.) or the dreaded 5G! (BUT only on HOR and not VER?).
I read another post where the OP (with his smaller 7.5 footer) played around with the illumination to peak desired transponder and reduce qrm on interfering/ stronger xpndrs (even on 103° W). So will play with that too - and cut away the RG-6 a and pull up a fresh section with new PPC and coax Seal. Open the throat cap see if any cobwebs are there and check servo operation (also changed in last maintence 10 years ago).

Finally, this will probably be the last chance I get to play with the BUD from the looks of it (providers leaving, auctioning off rest of spectrum imminent above 4.0 Ghz, and to keep the peace with neighbours so it would be nice to have that mux back for the long, cold and dark winters to comfort this old man before I call it quits and buy a VHF/UHF/FM Yagi and get MeTV, H&I from my Vermont local stations (checked at a friends today and they come in nicely - except ABC) .
Only one guy in town (Montreal) I may be able to get a receiver or PLL lnb from to try (RPS Sat) so hopefully with elimnate that as a possible culprit. Be nice to pick up a cheap or used PLL lnb to try w/o 5G BPF (money is tight )

Like others I couldn't care less about "tv" (well maybe just a liitle or a lot) it's the challenge that excites me , I can get MeTV other ways OTA (no pirate crap).

So what do you guys (and gals) think ?. p.s. I don't have a spectrum analyzer and there are def/ cell towers nearby (half a Km or so away).
Oh and time permitting will hammer out dings too and wire damaged mesh on one section for an extra dB or two. Hesitate to touch Declination, Elevation and pole mount but will play around with those a little too... Why is this mux for finicky suddenly ?(8psk, 5/6 fec, beamwidthetc.. man wish they went back to VER I think everthing would be fine! For the engineers out here does 5G QRM affect one poliarization (HOR) more than another (VER)? I understand the strong interference swamps out the input mixer/local oscilator in the hapless old C-band lnb (I think it at time affect KU too esp. LPB on 101°W KU - incidentally thos were weak or "gone' but are back almost at the time MeTV improved..hmm Terrestrial interference?

Any thoughts or suggestions ( cheap or free solutions please) greatly appreciated. Cheers.

p.p.s. Micro HD can't display Decades and Toons but records them fine so I can watch on another box/media player (Ali chip set issue). Another reason to upgrade.

Anybody interested in a nice C/KU system free ? (for next Spring/Summer 2027)

[Sami 10' mesh, Corotor II+, Eagle Aspen (very old) C-band lnb, Norsat Ku lnb, Channel Master C/Ku (H/V) switch, Startrak 400 Analog receiver w/ motor control, Geosat uHD DVD-S2, CW600S for Mpeg-2]
10 Replies · 380 views
cyberham
With the microHD connected this afternoon and tuned to the Weigel mux, I can receive the mux well.

My conclusion is that the sensitivity of the receivers in descending order of sensitivity is as follows:
  • V9 Prime (best)
  • microHD
  • Edision osmio4k+
Either the V9 or the microHD could be used to watch Weigel but the Edision really could not with my given dish situation, at least during the daytime. At night, the signal is stronger here and then maybe the Edision could be used.

Weigel mux.webp
Titanium
What is the SNR readings for these transponders? Is the signal breaking up due to low SNR or interference?

Did you inspect the feedhorn throat and wave guide for wasp nest or other blockage? Good SNR with frequent drops in decoding ( loss of SQ readings) could indicate interference from 5G.
T
Appreciate you checking. I should be picking these up with the tenner so still not done tuning up the bud - fell off ladder last week and hit my head!

Started over from scratch, N/S alignment, El/Decl extreme West sat, played with feed f/d checking everything and getting nice signals but still 101 west is PIA. New lnb was defective and returned it. My old one is fine but would have liked to A/B with a better lnb.

Thought it was the servo there because I was out and set everything up by the dish and flipping to HOR made a strange noise -BUT ONLY on 101 W ! All other sats skew is fine..hmm ( I have the skew almost perfect, use "Arrow" template on Zenith Sat (well nothing on 74 W to check with but Nimiq 5 at 72.6 W is closest and luckily picking up R- Pol channel from Canada to test with. Anyway picking up a new servo to try (the obvious polarity culprit).

Q. Back in the day PAS9 (74 W) was used but now I have to use closest zenith sat (Nimiq 5). I can't perfectly peak on that one which is 1 degree off (N/S alignment error). I used my trusty Brunton compass and even true noon shadow off pole to hit south.

I did have to peak extreme west by rotating mount ever so slighty so tracking extreme pretty good, but top and middle can use an elevation tweak (esp. Ku) to bring them back to where they were. No fun as the weather has been miserable and still dizzy from fall.

Oh and the Freesat V8 is crap (the tuner pixelates when the uHD is solid!) but love that SCART connector for S-Video out ! (I record to my Pio DVR and burn to DVD classic tv shows).

Stay tuned

With the microHD connected this afternoon and tuned to the Weigel mux, I can receive the mux well.
T
Did you inspect the feedhorn throat and wave guide for wasp nest or other blockage? Good SNR with frequent drops in decoding ( loss of SQ readings) could indicate interference from 5G.

Thanks for chiming in here. No wasps (or hornets nests) but good suggestion.

I am getting 70 and over Quality on uHD which is good but as you say the signal drops out (70 to 0 ) occasionally and much worse by day (even JTV which I used to get solid is a mess in the day. Again Daystar (VER) is fine but still not what it used to be.

I will will either have to get a BPF or go VHF/UHF for these channels but not giving up just yet!

p.s. Isn't there something between your feedhorn/lnbf BPF model and Norsat's 1500$ BPF and 5G filtering lnb's? Heck almost ready for a diy (reverse engineer) job here (microwave BPF hack) Ah where is Radio Electronics when you need it! If it wasn't for losing Ku I'd buy your lnbf in a heartbeat! Are these hard to add Ku to?
Titanium
Our LNBFs are integrated with the feedhorn and no KU option. Maybe install an inline waveguide BPF such as:

www.ebay.com/itm/158077455896
www.ebay.com/itm/960059145385
www.ebay.com/itm/158007483799
B
Howdy folks long time no write.

Issue(s): Horizontal transponders (esp. Weigel mux) breakup/mosaic/sputtering audio, JTV less so (but received perfectly up until a month or so ago.
Vertical is fine (Daystar). Up until recently couldn't even get any signal on Weigel Mux but JTV was perfect.

What I did to improve things: A slight westward move improved reception but only slightly (approx 72 on the micro HD, sorry no dB to post). I removed the 3-way C-Band splitter and used a 2-way to get a 1-2 db signal gain ( the power port goes to the Startrak - the micro HD doesn't have enough juice ! (1st clue) even after swapping the switching power supply it came with with a heftier linear 12 V supply (less RFI too !).
I have had issues with the uHD before signal breaking up that a reboot would clear up (clue #2 = dying tuner?) - FYI, I reinforced the IF input and removed all flux from the pcb completely with a Flux Removal Pen (MG Chemicals Cat No. 4140-P) which definitely makes a huge difference.

I went outside and pushed and pulled reflector slightly and no improvement. Pole (actually tower in yard - the neighbours love me..NOT) is plumb, checked with carpenters level. Dish was last peaked in 2017 or so, after overhauling 24" Von Weise, new Acme, fresh grease, etc. Focal length, f/d ratio etc meticulously adjusted. One panel has a tear so planning to repair that this weekend when my cousin comes over ( to help me out (old guy here) forecast calls for sunshine.

What has changed: My utility company has installed new high tension line poles (one smack dab in the middle of 101°W target! But they put it in last year and reception (of JTV (HOR) at least) was fine, BUT when they came out to transfer the wires over this year from the old (sawed in half) pole that's about when the troubles started (coincidence?), but again Daystar (VER) was fine. I always had this pole in the light of sight of 101° before with no issues. (fyi my zenith sat 74° is unobstucted, but can't test)

In the meantime Weigel mux is trying to break in MOSTLY in LATE at night (less cell usage?) (audio not video except for a frame here or there) so don't know what has changed with this mux which suddenly "woke up". I have never had to fuss with dish moves on this satellite ( the slightest move +/- motor clicks loses lock, wheres normally on C-band I can go significantly wider east or west and still have a strong signal ( have these gone "spot beam" or narrower somehow and what is the slight difference in Az listed on Lyngsat to 100.9° affect things ( isn't that the declination i.e. requiring a tweak of declination?).

Long story short (too late, ha), if I had another DVB-S2 box to try and / or a newer more stable PLL lnb ( I have been meaning to upgrade many a time but never got arround to it) I could determine if it's my antiquated receiving equipment, or my dish/feed alignment ( doubtful as it tracks everything from 55 °W to 133 ° W nicely.) or the dreaded 5G! (BUT only on HOR and not VER?).
I read another post where the OP (with his smaller 7.5 footer) played around with the illumination to peak desired transponder and reduce qrm on interfering/ stronger xpndrs (even on 103° W). So will play with that too - and cut away the RG-6 a and pull up a fresh section with new PPC and coax Seal. Open the throat cap see if any cobwebs are there and check servo operation (also changed in last maintence 10 years ago).

Finally, this will probably be the last chance I get to play with the BUD from the looks of it (providers leaving, auctioning off rest of spectrum imminent above 4.0 Ghz, and to keep the peace with neighbours so it would be nice to have that mux back for the long, cold and dark winters to comfort this old man before I call it quits and buy a VHF/UHF/FM Yagi and get MeTV, H&I from my Vermont local stations (checked at a friends today and they come in nicely - except ABC) .
Only one guy in town (Montreal) I may be able to get a receiver or PLL lnb from to try (RPS Sat) so hopefully with elimnate that as a possible culprit. Be nice to pick up a cheap or used PLL lnb to try w/o 5G BPF (money is tight )

Like others I couldn't care less about "tv" (well maybe just a liitle or a lot) it's the challenge that excites me , I can get MeTV other ways OTA (no pirate crap).

So what do you guys (and gals) think ?. p.s. I don't have a spectrum analyzer and there are def/ cell towers nearby (half a Km or so away).
Oh and time permitting will hammer out dings too and wire damaged mesh on one section for an extra dB or two. Hesitate to touch Declination, Elevation and pole mount but will play around with those a little too... Why is this mux for finicky suddenly ?(8psk, 5/6 fec, beamwidthetc.. man wish they went back to VER I think everthing would be fine! For the engineers out here does 5G QRM affect one poliarization (HOR) more than another (VER)? I understand the strong interference swamps out the input mixer/local oscilator in the hapless old C-band lnb (I think it at time affect KU too esp. LPB on 101°W KU - incidentally thos were weak or "gone' but are back almost at the time MeTV improved..hmm Terrestrial interference?

Any thoughts or suggestions ( cheap or free solutions please) greatly appreciated. Cheers.

p.p.s. Micro HD can't display Decades and Toons but records them fine so I can watch on another box/media player (Ali chip set issue). Another reason to upgrade.

Anybody interested in a nice C/KU system free ? (for next Spring/Summer 2027)

[Sami 10' mesh, Corotor II+, Eagle Aspen (very old) C-band lnb, Norsat Ku lnb, Channel Master C/Ku (H/V) switch, Startrak 400 Analog receiver w/ motor control, Geosat uHD DVD-S2, CW600S for Mpeg-2]
I had the EXACT same problem happen to me with 101w, MeTV mux (Weigel). Working great when about 3 weeks ago I started to get the pixelating, especially at night. Sometimes Jewelry TV would also do it, sometimes not. Tweaked my dish. I have a Titanium 240 feed with the 5G filter 4.0-4.2 band pass. Every other satellite is working fine. Something on their end for sure. Power reduction? My signal seems fine like always. Running a Winegard 8.5 ft dish using a GT Media UHD V8. I'm sure my receiver isn't maybe sensitive enough for lower signal levels. Frustrating here too. I'm in the Canton, Ohio area. Thanks!
arlo
To me it looks like all of the intelligent things to diagnose the problem 'on the cheap' are being done.
I have my own thoughts of lnbf's using an external filter between the feed and coax. It would be cool to see what Brian could add.
Do his units have the filter before the actual LNA chip in the circuit? In other words, signal is focused at the lnbf throat. The probes for h & v polarity send the signal to.......filtering......then to the lna IC......
Or probes, lna, then filtering. Makes sense to trap the bad stuff before amplification to me.

On the cheap sometimes leaves questions. Enosat and El Bandido both use dvb-s pci cards and TBS USB receivers.
With those, and software. Signal analysis becomes sort of easy. Or tapping into your coax with a dc pass splitter, decoupling capacitor, and using a spectrum analyzer. Tuning across the LO band. Finding signal spikes. Digging deep.

Still making my decision on a (most probably) TBS PCIe tuner card. But I have tapped into my coax with my ancient but quite impressive HP spectrum analyzer and tinysa.
I don't have 5G interference so far that I know of. But have my suspects because I'm only able to snag signal from 131W in the winter when the leaves drop. But out of curiosity do scan it in the fall. And seem to be getting a signal that 'shouldn't' be there and a scan shows no channels. Far as I got.

An idea pops up to rig up an LNBF on a stick. Along with the tinysa and power supply and do some rogue signal searches. War Driving, of sorts. But. I wouldn't think that a chinabox, firmware based receiver would be of much help.
From what I see scanning across the frequency band. 5G cell transmission is always on and is very wide spectrum.
Whether anyone is actually using talking, texting, watching stupid human tricks on YouTube Makes no difference. The RF is there. So why would a C Band setup come and go? And what if you dumped the corotor and went modern voltage controlled polarity?

Another thought. Since you've learned the optimal position to place the scalar to illuminate out to the dish rim. And peaked the feed. There's most of a roll of aluminum flashing out in my garage that would most definitely wrap around my dish perimeter. That and a bag of large binder clips from the office supply. wally world. Ideas?
meStevo
Lifetime Supporter
Last reply · posted in The Sports Section
Schedule drops tomorrow. Mandatory mini camps in June. Hall of Fame game August 6th.
117 Replies · 1872 views
  • Like
Reactions: Jimbo and dfergie
Foxbat
I guess even the patience of us laid-back Hoosiers has its limits:
rvvaquero
I guess even the patience of us laid-back Hoosiers has its limits:
Be nice to see a Cowboy headline like that.
M
I guess even the patience of us laid-back Hoosiers has its limits:

Can we expect to see a new coach if we say "pretty please?"
  • Like
Reactions: Foxbat
Foxbat
Jeeez, Week 6, no lead is safe…
  • Like
Reactions: Mike0616
b4pjoe
Be nice to see a Cowboy headline like that.
Yes the Cowboys owner needs to fire the general manager (himself), co-owner, Chief Operating Officer (COO), Executive Vice President, Director of Player Personnel, and President of AT&T Stadium (his son) and then he should jump off of a cliff. Only then can they recover.
T
Last reply · posted in DISH Network Support Forum
I thought I would come here and find lots of complaints about the update to the dish anywhere mobile app, but am not seeing any. It used to look just like the desktop webpage. Now you can no longer filter by sports channels or movie channels. Plus that they made it look like a big button telephone and you see fewer channels in the screen which requires more scrolling. Yes I realize you can look at sports then select which sport you want to look at, I just liked being able to see all sporting events in the guide with all other channels being filtered out. Am I alone in the wilderness on this?
8 Replies · 289 views
  • Like
Reactions: dishstaller
dishdude
I like the new look, it's a lot cleaner. I'm using it on one of those Onn streaming devices when I travel.
  • Like
Reactions: charlesrshell
T
I like the new look, it's a lot cleaner. I'm using it on one of those Onn streaming devices when I travel.
Yes a lot cleaner, glossier, and less functional. Someone trying to justify why they are making a big salary. "See look shiny"
  • Like
Reactions: charlesrshell
navychop
"Big salary." Charlie. "?Big?"
Tampa8
Seems in some ways better. Nicer layout, as others said maybe cleaner. Moving ahead in the guide is better.
S
I thought I would come here and find lots of complaints about the update to the dish anywhere mobile app, but am not seeing any. It used to look just like the desktop webpage. Now you can no longer filter by sports channels or movie channels. Plus that they made it look like a big button telephone and you see fewer channels in the screen which requires more scrolling. Yes I realize you can look at sports then select which sport you want to look at, I just liked being able to see all sporting events in the guide with all other channels being filtered out. Am I alone in the wilderness on this?
I think most are using it on a firestick or other device as an extra receiver, rather than their phone. Just a guess based on how I use it. 99% thru my firestick, 1% phone.
  • Like
Reactions: llokey
dfergie
Staff member HERE TO HELP YOU!
Last reply · posted in TV Shows
Stargate SG-1 cancelled, Atlantis renewed
clear.gif

Monday - August 21, 2006 | by Darren Sumner
clear.gif

The future of Stargate is in question today, as SCI FI Channel has cancelled the long-running Stargate SG-1, Multichannel News reported today and a GateWorld source has confirmed. The news regrettably follows the airing of the show's milestone two-hundredth episode on Friday.

Stargate Atlantis, meanwhile, has been renewed for a fourth season, with the network hoping to see that the spin-off series can stand alone, according to a source.
Source Gateworld
2034 Replies · 184189 views
R
I have gotten back into watching SG-1 and I have recorded most of the episodes to binge watch. What episodes are about the Antarctic or was this a movie? Also where could I watch the SG-1 movies?
osu1991
long_time_Dish
I have gotten back into watching SG-1 and I have recorded most of the episodes to binge watch. What episodes are about the Antarctic or was this a movie? Also where could I watch the SG-1 movies?
Well, there are a couple involving the Antarctic. "Solitudes", S1 E17 (one of my favorites), Then, "Lost City', S7 E21 and E22. Then, in the SGA pilot, "Rising", S1 E1 and E2, it starts out in the Antarctic for about the first 20 minutes or so.
R
Well, there are a couple involving the Antarctic. "Solitudes", S1 E17 (one of my favorites), Then, "Lost City', S7 E21 and E22. Then, in the SGA pilot, "Rising", S1 E1 and E2, it starts out in the Antarctic for about the first 20 minutes or so.
Which one has O'Neil being Ancients? I am at the end of Season 8 now.
long_time_Dish
Which one has O'Neil being Ancients? I am at the end of Season 8 now.
If I understand your question, O'Neill had the Ancient's knowledge in the "Lost City" two-part episode. That was when Anubis attacked Earth and there was a big battle over Antarctica.
  • Like
Reactions: dfergie and Foxbat
R
If I understand your question, O'Neill had the Ancient's knowledge in the "Lost City" two-part episode. That was when Anubis attacked Earth and there was a big battle over Antarctica.
Those are the episodes I am looking for. They are referred to a lot in the episodes I just recently watched.
  • Like
Reactions: dfergie
T
Last reply · posted in Free To Air (FTA) Discussion
Picked up a sweet directv dish, mount, twin lnbs and a short cable.
Has anyone converted one to FTA? A Frankenstein of sorts...
6 Replies · 302 views
B
would probably also work well for NHK on 101W and possibly for PBS on 99W. I used one for a while on 30W. Just keep in mind that because it's undersized for those satellites, it might work fine in clear weather but won't have much margin to account for signal degradation during rain/snow
  • Like
Reactions: TVHabit
O
If you can find one, the Shaw / Star Choice 75e ellipticals are great for use on 97, 99, and 101W. They are really just rebranded ChannelMaster 75 cm reflectors and use linear LNBFs by default out of the box.

Everyone else's mileage may vary.
  • Like
Reactions: TVHabit
T
I have read that some have converted this type dish but after giving it a good look, it's the lnb conversion that is the bottleneck. Does anyone have a picture of their attempt to configure the lnb? I watched a video on youtube from the save it for parts guy and he used duct tape! Guess it worked but I'm thinking something a bit more permanent!
Thanks to all for your interest and replies...
Titanium
Many of us have used a universal LNBF mount (or get creative with L brackets and plumbers tape - perforated metal strapping). Use a few inches of aluminum tube (or a piece of 1x2" lumber) to extend the support arm (replacing the plastic mount used by DirecTV and Dish) to place the LNBF throat opening at the correct distance from the reflector, the correct height and at the correct angle. Nothing magical... simply place the new linear LNBF in the center at the same distance, height and angle as the current combo.
www.amazon.com/Universal-Single-Bracket-Holder-FTA-US/dp/B074L85WK2
LNBF mount.webp
  • Like
Reactions: FTA4PA
k4otl
To add: 101W Ku seems to be (one of if not the) strongest for me, and if I only had Ku I definitely want 101W for the music mux, it's robust FEC and strong signal help a lot. I've thought about using a used Dish/DirectTV dish at my Dads to supplement his OTA (mainly for my benefit when I visit :) )