Social Feed

M
Last reply · posted in C-BAND Satellite Discussion
Anyone know off hand the arc that can be traveled with a VW 24" actuator?

Dish is a Winegard 8.5ft set for western sats, no modifications done. At 137 degrees the limit stops movement and the arm is more or less all the way in. I have my eye on some sats in the 50 on the C side but afraid this is far out of the limits of the actuator. Anyone have a similar dish and the idea of what arc range it can pull off?
18 Replies · 3479 views
M
Thats what happened. Looked at it this morning and the nylon acme nut is stripped clean. I know that it had seized up on the way back as according to who I got it from the dish sat still for 10+ years. The rubber boot that goes over both telescoping sections was in the wrong spot and the sliding section was wide open to allow water to get in and seize up everything and it was horribly seized when it was apart. Thought it was cleaned good but it still catches in places from the rust damage.

Ill have to put it back in so I can leave it on W5 until I can find an 24" arm on eaby hopefully new and cheap .

On the plus side I can get a lock on 59W with the FTA but the dish has to be picked up a little. Dont even know about the Ku side of the dish yet since that was also last nights project until it died.

DOH!!!
M
Another update:

Using the old nut that was a different style and some "home brew engineering", its back together and moving. The Ku side I do not have a signal on as is but I believe I need to raise the elevation.
Lone Gunman
What kind of actuator do you have? I did a rebuild with pics on a VonWeise earlier this year and those factory nylatron nuts are available from VonWeise for about $25 or so. When I did mine I bought bronze nuts to replace the plactic and never looked back!! One of the two I did at that time has been in service now for about 6 months and is working great. The other is in my closet waiting for that 12 Foot Conifer dish I plan to bring home this spring.
M
This one is a Von Weise V76-5 but the smaller telescoping section that has the threaded eye bolt where the dish connects is from a V24-LC. The original from the 76 is damage and needs major work done to it plus a nut for it.
Lone Gunman
This one is a Von Weise V76-5 but the smaller telescoping section that has the threaded eye bolt where the dish connects is from a V24-LC. The original from the 76 is damage and needs major work done to it plus a nut for it.

At one point I had contacted a solar panel company out in Arizona and they had that complete inner tube with a new nut for around $100. Problem with that though is you can get a 24" mover off of fleabay for around $50. I went to the trouble to rebuild my VonWeise movers because I believe they are better than the China junk and I have the tools and know how to make that happen.

You can search for posts made with my username and find the post on the VonWeise rebuild and also I put that info on my racing forum here Motorsports Village • View topic - Von Weise Acme Nut Repair
meStevo
Lifetime Supporter
Last reply · posted in The Chit Chat Club
Continuing the Kilauea thread in the Pub here. Perhaps the Iceland one too next time there's remarkable activity.

Currently there is precursory lava flowing into the crater, leading to the next episode that'll probably start within the next day.

You can see the pace of inflation / deflation here. It serves as the primary predictor for when the expect the eruptions, which coincide w/ inflation turning into significant deflation and last for several hours on average with significant fountaining.



View: https://youtu.be/Uecu2seh4b4


Wife and I like the AfarTV feeds, for the discussion along w/ them, though they're otherwise just mirrors of the official USGS feeds.


View: https://youtu.be/iws3rh5vLAQ
123 Replies · 3655 views
  • Like
Reactions: osu1991
Foxbat
Kīlauea seems to be returning to the "normal" eruption script, impressive fountaining from the North Vent. For once, the V2 Cam has the best overall shot:
IMG_1535.webp
The lava flows have covered a good portion of the Halemaʻumaʻu crater floor.
Foxbat
Looks like Episode 55 is over at 09:00 HST, just under six hours. The USGS said the fountains reached 720' or 220 meters.
​
  • Like
Reactions: RaiderPower
Foxbat
The USGS Kīlaeua Webcam #1 has been showing overflows and doming from the North vent overnight. Maybe the volcanic plumbing has settled back into its two-three week cycle of fountaining?

But I do miss the little cinder cone that broke up in the last episode.
Foxbat
Sorry, I should have posted these earlier:

​

We're still waiting on the start of Episode 56.
  • Like
Reactions: RaiderPower
Foxbat
At 08:01 HST 11/05/2026, the North Vent produced what I would call a "wet burp" after the precursory "pistoning" events, small amounts of lava pouring out of the vent for a few seconds to minutes and then everything recedes. There must have been a gas bubble holding thing back because two minutes later the lava started flowing out of the vent in all directions. Then, at 08:25, it stopped. What a tease! I thought this was how Episode 56 started.

About 12 minutes later at 08:38, the North vent once again started overflowing and picked up steam at 08:42. By 09:00, slight doming could be seen in the pool of lava in the vent. Surely this is it!

But, 09:50 and things wind down again. By 09:57 HST there's just fumes coming out of the vent. Phooey.

But then 10:00 comes and the heavy lava flows kick in again. This time seems like the real deal. At 10:30 HST there's little spurts of lava flying up in the air over the vent, but more from gas than a steady fountain of lava. This looks promising!

11:30 HST and the color of the lava is definitely hotter, and the intensity has picked up to a definite dome and precursor to fountaining. The USGS calls Episode 56 as officially starting at 12:10 HST:

Alert Level: WATCH, Color Code: ORANGE 2026-11-05 22:29:12 UTC
HVO/USGS Volcanic Activity Notice

Volcano: Kilauea (VNUM #332010)

Current Volcano Alert Level: WATCH
Current Aviation Color Code: ORANGE

Issued: Thursday, November 5, 2026, 12:29 PM HST
Source: Hawaiian Volcano Observatory
Notice Number: 2026/H514
Location: N 19 deg 25 min W 155 deg 17 min
Elevation: 4091 ft (1247 m)
Area: Hawaii

Summary: Episode 56 of the ongoing Halemaʻumaʻu eruption began at 12:10 PM HST on November 5, 2026.

Volcanic Activity:
Episode 56 of lava fountaining in Halemaʻumaʻu began at the summit of Kīlauea began at 12:10 PM HST on November 5, 2026.

Lava fountain heights are relatively low at about 100 ft (30 meters), but will likely increase. Ground-level sensors near the eruptive vents indicate that winds are blowing from the northeast direction, which suggests that volcanic gas emissions and volcanic material may be distributed to the southwest direction from Halemaʻumaʻu.
K
Pub Member / Supporter Lifetime Supporter
Last reply · posted in TV Shows
'Rockford Files' Reboot Gets NBC Pilot Order

I grow tired of all the reboots. Most I don't bother with but will depend on the actor chosen.
17 Replies · 720 views
osu1991
  • Like
Reactions: MikeD-C05
K
January? OK.

I'm sure I will check it out. Not getting my hopes up but I did enjoy the actor in SEAL Team. Never saw any of his earlier work.
long_time_Dish
Yeah, I'll check it out as well, but shan't be holding my breath...It'll be tough to equal James Garner in that role...
  • Like
Reactions: Foxbat
harshness
...It'll be tough to equal James Garner in that role...
I can think of a few actors (including some females) who might fit the bill.

This will all depend on the storyline. I'm not sure how well it will translate. Modern TV hasn't been all that kind to PIs and even less kind to CIs (confidential informants).
K
Premier is Saturday, Jan 2nd. Moving to Thursday on the 7th.
  • Like
Reactions: osu1991
osu1991
Pub Member / Supporter
· posted in Movie Talk
0 Replies · 5 views
osu1991
Pub Member / Supporter
· posted in Movie Talk
0 Replies · 10 views
M
Last reply · posted in DISH Network Support Forum
I have Dish with Hopper3. I choose to get local channels OTA and had a "guide list" established at my previous home. Having moved a few miles away, I wanted to update the list by appending a couple new stations via a rescan. As many would know, some stations come in with the UHF/VHF antenna aimed in one direction, while others come in better with a different direction.

Unfortunately, when a scan is done (bringing in 25-30 stations for that particular antenna aim), the dialog screen does not present the established guide list; it presents an empty field to the right that the scanned stations may be selected one by one and added to the empty guide. But because of antenna aim, some stations originally saved are missing, and would have to be retrieved with a different antenna aim. But as I explain, if a 2nd​ scan is done with a different antenna aim, the stations saved from the first scan are lost.

It troubles me that Dish didn't develop software that would allow a user to simply append only 1 or 2 channels to the established list. :mad:

Any thought on this? Has anyone experienced this or heard of this from others?
15 Replies · 490 views
dishstaller
I could very well be wrong....it has been a LOT of years but back when I had a 722K it seemed like when you went back to the scan screen that you could just scan again and it would ADD those channels to the previous list or you could delete the previous results and only add the channels from the new scan.
  • Like
Reactions: charlesrshell
N
I could very well be wrong....it has been a LOT of years but back when I had a 722K it seemed like when you went back to the scan screen that you could just scan again and it would ADD those channels to the previous list or you could delete the previous results and only add the channels from the new scan.
I am not sure about that but I do know that you could manually add additional channels just by entering the actual RF channel number and the older receivers would add the virtual channels to your list
dishstaller
I am not sure about that but I do know that you could manually add additional channels just by entering the actual RF channel number and the older receivers would add the virtual channels to your list
Like I said.....that has been many years ago. Swapped my 722K for a Hopper in 2012.

It does seem like I remember having to delete the existing channels when we did a rescan. Back then our local stations KEPT monkeying around with things and it was non-stop complaints from customers about their channels not coming in. Got so bad that I stopped selling OR installing OTAs....something I had been doing since 1984 so you know it HAD to be pretty bad.
M
You made one of my points for me with this comment, Dishstaller:

"... local stations KEPT monkeying around with things and it was non-stop complaints from customers about their channels not coming in ..."
dennispap
I could very well be wrong....it has been a LOT of years but back when I had a 722K it seemed like when you went back to the scan screen that you could just scan again and it would ADD those channels to the previous list or you could delete the previous results and only add the channels from the new scan.
I remember that also on my 722.
dishstaller
I remember that also on my 722.
Thanks.....has been too many years to remember clearly.
  • Like
Reactions: charlesrshell
Bobby
Keep in mind that the 722 had a built in OTA tuner and the 722K had a plug in module for OTA. The Hoppers and Wallys use an add on USB OTA dongle. I believe they are entirely different.
Linus Tech Tips
· posted in Linus Tech Tips
0 Replies · 10 views
osu1991
Pub Member / Supporter
Last reply · posted in TV Shows
12 Replies · 249 views
osu1991
Finished the 2nd episode tonight. I'm really liking it so far.

Still hate weekly releases though, especially the way Disney and HBO do it waiting until 8pm to premiere it.
Foxbat
Apparently I'm not a big enough nerd🤓 since I did not read every Marvel Comic Book ever published. If I had, I might be comparing the comics' version of events compared to what's transpiring in "Visionquest". So, I am enjoying the series a lot, not weighed down by previous expectations, knowing only the Avengers MCU movies and the "Wandavision" / "Agatha All Along" TV series.

I found the Mr Know-it-All channel from his discussion about "Star Trek: Strange New Worlds" and he's been gleefully picking these episodes apart, referencing the Marvel comics from the 1939 on. Turns out A.I. has been around since before World War II, at least in the comics. (Robots before that, yes, yes.) This show is going back into the archives.
  • Like
Reactions: osu1991
Foxbat
I'm expecting the finale to basically bring Vision into play for the Doomsday movie next month.
  • Like
Reactions: osu1991
osu1991
annoying they went with single episodes for the last two after releasing two a week for the first 3 weeks
Foxbat
annoying they went with single episodes for the last two after releasing two a week for the first 3 weeks
I thought they were effectively releasing a longer episode 7 and 8 instead of shorter episodes 7 & 8 this week and 9 & 10 next week. It felt like they were packing more into this episode.

edit: But you're right, the run time of the first three pairs of episodes was 100 minutes on average. Episode 7 clocks in at 65 minutes. 😕
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in The Chit Chat Club
Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne


Get it?


An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
68756 Replies · 2684890 views
  • Like
Reactions: c-spand
harshness
I Can't Wait - Nu Shooz
gms49ers
Shooz - Styx
  • Like
Reactions: long_time_Dish
dishstaller
Too Much Time on My Hands - Styx
sdfntx
Time Has Come Today - The Chambers Brothers
  • Like
Reactions: Bobby
long_time_Dish
No Time - The Guess Who
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in DIRECTV General Forum
The following is from Reddit. -
View: https://www.reddit.com/r/DirectvStream/s/orzHBkmqQW


gemini.webp

There appears to be a new DIRECTV Gemini OTT box, the C81KW-650.

The FCC listing is partially available, and a Geekbench entry confirms it uses an Amlogic S905X5, a solid SoC for a set-top box.

I also see 4GB of RAM, and the manufacturer is SEI Robotics.

DIRECTV C81KW OTT Box - Android TV Guide

Ok found a picture of the Box too on Reddit:


View: https://www.reddit.com/r/DirectvStream/comments/1twlex0/comment/opzeqi1/
25 Replies · 1395 views
  • Like
Reactions: dtv757
Scott Greczkowski
I know a few people who have gotten one and I am told like most modern streaming boxes this one also has HDR on all the time.
Tom Speer
I know a few people who have gotten one and I am told like most modern streaming boxes this one also has HDR on all the time.
I only noticed that as a problem on TVs that handle HDR poorly. They don't have enough peak brightness or enough dimming zones. For instance, TCL makes three lines of TV, sort of like the old Sears model of Good, Better, Best. On my 4 or 5 year end low price model, HDR looked awful (My neighbor likes the TV now). The midrange model from the next model year ithat I have at my Lake home now looks pretty good in HDR all the time. The midrange TCL QM7 model from last year at my other home looks spectacular, as I remember. I haven't seen it for 6 months.

If I had a TV that does HDR poorly, I would configure the Gemini to disable all HDR.
  • Like
Reactions: b4pjoe
b4pjoe
I only noticed that as a problem on TVs that handle HDR poorly. They don't have enough peak brightness or enough dimming zones. For instance, TCL makes three lines of TV, sort of like the old Sears model of Good, Better, Best. On my 4 or 5 year end low price mode, HDR looked awful (My neighbor likes the TV now). The midrannge model from the next model year ithat I have at my Lake home now looks pretty good in HDR all the time. The midrange TCL QM7 model from last year at my other home looks spectacular, as I remember. I haven't seen it for 6 months.

If I had a TV that does HDR poorly, I would configure the Gemini to disble all HDR.
I agree with that. The 2 LGs that we have Gemini's on looks far better with HDR enabled then it does with HDR off.
R
I know a few people who have gotten one and I am told like most modern streaming boxes this one also has HDR on all the time.
That would be a deal-breaker for me. The Rokus default to having it on all the time but it's easy enough to change that to native. If the content is HDR it goes on. Otherwise, no.
R
I don't mind HDR being on as long as its adaptive. I don't need HDR on non-HDR content

Also, God only knows how much it'll cost to get this per month. 10 bucks a month for 3 TVs in my apartment is not worth it if I can just use my android boxes and appletv to watch
b4pjoe
I don't mind HDR being on as long as its adaptive. I don't need HDR on non-HDR content

Also, God only knows how much it'll cost to get this per month. 10 bucks a month for 3 TVs in my apartment is not worth it if I can just use my android boxes and appletv to watch
It is not adaptive. HDR is either always on or off. No in between. However with my Gemini on satellite everything looks much better with HDR on.
  • Like
Reactions: Tom Speer