Social Feed

Garlic cheese bread
Green beans
Apples
Chocolate Milk
Some weird noodles.
(They have salad and a couple other fruits if wanted)

Club sandwich and corn chowder. Iced tea.

Chili dog bowl, water… (homemade chili)

Leftover wanton soup and pork fried rice. Water.

Sweet tea…

I Wanna Talk About Me - Toby Keith

98.6 - Keith

I'm Easy - Keith Carridine

It's Easy - Boston

Take It Easy On Me - Little River Band

A recalibration might be needed. Even if it shows full, the individual cells may have become unbalaced. And the BMS chip in the battery reports false information to the pc.
Try this. Start it up in the bios/uefi and leave it there until the battery dies and it shuts off.
It might just keep running longer than in Windows. Or run for a short while and shut off.
If it's the first case. Probably just needs a balancing. If the latter, the pack might just be dead.
Not throwing stones but perhaps just a cheaply constructed battery with substandard cells. Could be.

Patience. Keep restarting it in bios/uefi until it won't fire up anymore.
Then plug the charger in and let it complete a full charge. And see what happens. If it's better.
Do the same thing one more time. Run it until it dies dead-dead. Then just let it charge, pc shut off.
When charged, it might be better. It might not be.

There are bench jigs that read the actual BMS and override it to let a tech manually monitor and charge the separate packs. They can also reset any "time bombs" in it that cause an otherwise good pack to show bad.
Maybe Santa will be good to me some year.

You might just need a new battery. Maybe the PC power management chip is going. A Dell common thing.
Leaving a laptop plugged in with a full battery is known to reduce the life. Asus for one recommends that you don't leave the charger plugged in all of the time even when shut down. And setting Windows to charge the battery to 85% instead of 100% increases life.
That's all I got.

arlo said:

That's all I got.

Click to expand...

That was quite enough....I definitely learned something from your post. Thanks

TRG said:

I set up a music server for my brother a few years ago. It's basically a small headless computer but it needs to have a DHCP IP address reserved for it in the router settings. This was easy to do in his DSL router. He's switching to Starlink now and I was wondering if these setting are easily accessible in the Starlink router. I'm pretty sure he will be getting the latest V5 router.

Click to expand...

If you can't get into the router to reserve an IP address just don't use DHCP on the device that needs connected and assign it to a specific IP address in the network settings.

TRG said:

I set up a music server for my brother a few years ago. It's basically a small headless computer but it needs to have a DHCP IP address reserved for it in the router settings. This was easy to do in his DSL router. He's switching to Starlink now and I was wondering if these setting are easily accessible in the Starlink router. I'm pretty sure he will be getting the latest V5 router.

Click to expand...

They are not. Your best bet is to set up a third-party router, attached to the Starlink for your server, that you can get into, like a Linksys, etc

TRG said:

…it needs to have a DHCP IP address reserved for it in the router settings. This was easy to do in his DSL router. He's switching to Starlink now and I was wondering if these setting are easily accessible in the Starlink router. I'm pretty sure he will be getting the latest V5 router.

Click to expand...

The Starlink V5 Install Kit I just got comes with the Mini Router. It is pretty limited in what it can do. For example, it can provide only one IP subnet at a time, no Guest Network, but it does support the pass-thru to a third-party Router. You can also split the Wi-Fi into separate 5 GHz & 2.4 GHz SSIDs to help some IoT devices that don't support 5 GHz bands to work.

The larger Starlink Router that still comes with the V4 Kit does support a Guest Network with separate IPv4 Subnet, but it's $120 from Starlink. And it still won't do DHCP Reservations.

If you can restrict the DHCP address space to assign addresses to one end of the subnet (i.e. x.x.x.50+), you can manually assign the IP address on pretty much any operating system. This is a default behavior on several popular routers. As the Router Mini only supports 235 devices, I expect that's already done.

Another option is to use a router that supports PoE to power the antenna. This article discusses that option (under PoE Power heading):

Now that I've had the v5 kit with the Mini Router, it's not as bad as I first thought. Yes, no DHCP reservations, but you can set up multiple SSIDs that have separate IPv4 subnets, and like the big brother, you can select from 192.168.x.0/24 or 10.x.0.0/16 (where "x" is 1-4).

You can also split a subnet and have different SSIDs for the 5 GHz and 2.4 GHz channels to handle some IoT devices. I haven't discovered what subnet the 2nd NIC on the router assigns, I'm guessing it's the first subnet.

Not Rodney, but a laugh ...

View: https://www.youtube.com/shorts/WHEcmortfK0?feature=share

Sorry for posting the wrong link. Just corrected it.

dishstaller said:

Terrible tragedy. You would think that they would have safe guards in place that would prevent something like this from happening. I guess if you are going to ride in a passenger train it might be best to get a car near the rear.

At Least 64 Dead After Two High-Speed Trains Collide In Spain<!-- --> | ZeroHedge

ZeroHedge - On a long enough timeline, the survival rate for everyone drops to zero

www.zerohedge.com

Click to expand...

They will have to look at the switching sections to determine WHY 2 trains were on the same track ... at the same time.

Thought this article might be of interest to some of you who might travel via train.