Social Feed

electronmini
Last reply · posted in Free To Air (FTA) Discussion
Hi, I just did a factory reset on the Openbox S9 I have been using for PBS in 125 W and right after that came with "Nocha" and my TV said: "Video Not supported". I is the same TV I have been using with the S9 for 6 years.

Everything was working fine and was a stupid move probably due to my age. I was getting all PBS channels.

Also I have been using it for 3 or 4 years without the remote because stopped working and the problem is not the remote bu the S9 Box.

I tried to hook it to other TV's but says the same thing: "Video not supported"

I read Iceberg post on have to go to the satellite list and choose satellite. That worked for someone else, but I cannot see the menu.
Is there any way I can get to " see" what is going on and do that? Or may I need to reload software? But how can I load the software id I cannot see the menu?
My TV is a Emerson Digital and has only a DMI input and attached are pics of the rear panels.
If I need new software, I could not find it in this site, please help.

Please help with some suggestions,
Thanks in advance
66 Replies · 6463 views
Titanium
The firmware hard coding cannot be changed by the end user, but the user settings can be set using the directions provided. Some editor software programs also allow these user settings to be edited and saved as the default. On some STBs, the user settings can be saved as the default and a firmware back-up file can be saved to USB or extracted with ALI Editor.

The reason that these resolution parameters are need is because the majority of the world power and video refresh rates are 50hz. Here in North America (and a few other countries) the power and video refresh rates are 60hz. Some TV, don't support HDMI handshake, so the default refresh rate is typically set to the frequency used in the country of distribution.

Usually .abs files are the firmware and might also contain the satellite/tp/channel lists. .udf (User Database File) are typically the user files and are wiped out if a factory reset is performed.

It is possible that the HDMI output has failed. This is a common problem with Openbox STBs. Does the AV RCA outputs provide any image? BTW... the "video not supported" message is generated by the TV and not the STB. Is the same message displayed if the HDMI cable is unplugged? Same message if the AV RCA cables are connected to the TV?
  • Like
Reactions: electronmini
electronmini
The firmware hard coding cannot be changed by the end user, but the user settings can be set using the directions provided. Some editor software programs also allow these user settings to be edited and saved as the default. On some STBs, the user settings can be saved as the default and a firmware back-up file can be saved to USB or extracted with ALI Editor.

The reason that these resolution parameters are need is because the majority of the world power and video refresh rates are 50hz. Here in North America (and a few other countries) the power and video refresh rates are 60hz. Some TV, don't support HDMI handshake, so the default refresh rate is typically set to the frequency used in the country of distribution.

Usually .abs files are the firmware and might also contain the satellite/tp/channel lists. .udf (User Database File) are typically the user files and are wiped out if a factory reset is performed.

It is possible that the HDMI output has failed. This is a common problem with Openbox STBs. Does the AV RCA outputs provide any image? BTW... the "video not supported" message is generated by the TV and not the STB. Is the same message displayed if the HDMI cable is unplugged? Same message if the AV RCA cables are connected to the TV?
Maybe the HDMI in my open box has failed, but was working well just before I did the factory reset.
Again, the S9 manual says that the default for video format (they call it native) is 480i as I proved by using my frind's S9 box, so why should I not see a picture of the menu?
KE4EST
so why should I not see a picture of the menu?
There were many versions of firmware floating around for the S9. It most likely has a different version of firmware that is not set for 480i default.
  • Like
Reactions: electronmini
electronmini
There were many versions of firmware floating around for the S9. It most likely has a different version of firmware that is not set for 480i default.
KE4ST:
That could be the case but if you look at the files sizes of the 3 versions I was given, all are 4,096 or something like that. Any recoding would be a very casual coincidence that ended up like that. But certainly Possible!
Thanks, now l will try again blind Manu navigation with emphasis on waiting 1/2 minute or more in the last step to give the TV receiver more time to adjust.
Thanks
KE4EST
KE4ST:
That could be the case but if you look at the files sizes of the 3 versions I was given, all are 4,096 or something like that. Any recoding would be a very casual coincidence that ended up like that. But certainly Possible!
Thanks, now l will try again blind Manu navigation with emphasis on waiting 1/2 minute or more in the last step to give the TV receiver more time to adjust.
Thanks
Not sure what you mean by recording, but any recordings you make would not affect the file size of the firmware.
Also they will all be the same size no matter the what is in the firmware or the version. Think of it like a container that is the same size no matter what. That is the file size that the receiver is looking for, for a valid file.

Think of it like a container or jug of milk. You go to the store and you by a container(jug) of milk. The container is full. Then you drink half of that jug of milk. You now only have a half of gallon of milk, but the container is still the same size. Your jug of milk is still the same size jug even though there is less milk. Same way with this file. It will always be compiled and placed in a "container" of the same size.
electronmini
Not sure what you mean by recording, but any recordings you make would not affect the file size of the firmware.
Also they will all be the same size no matter the what is in the firmware or the version. Think of it like a container that is the same size no matter what. That is the file size that the receiver is looking for, for a valid file.

Think of it like a container or jug of milk. You go to the store and you by a container(jug) of milk. The container is full. Then you drink half of that jug of milk. You now only have a half of gallon of milk, but the container is still the same size. Your jug of milk is still the same size jug even though there is less milk. Same way with this file. It will always be compiled and placed in a "container" of the same size.
KEY4:
I meant re-coding that is the act of editing a computer program. I am fairly good in that area since I have done programing in C language, Cobol, and a couple more less utilized language. After the changes to the program an any lanuage and processed by a "compilor"
electronmini
KEY4:
I meant re-coding that is the act of editing a computer program. I am fairly good in that area since I have done programing in C language, Cobol, and a couple more less utilized language. After the changes to the program an any lanuage and processed by a "compilor"

Sorry the reply escaped before I finished, here I continue:
I spelled compiler incorrectly, the correct speling is compiler. When a programmer changes the program is changing the number of character in the source language and most often takes/deletes or adds a bunch of lines. That is called the source code and is fed to a COMPILER which in turn only by a GREAT accident in life will give the same number of bytes for a file.
Same will apply to the abs file if used as "reference parameters" by the executing program.
I apologize if I am offending with this lo g explanation, but that is life in the programing world. Now that said, programmmers could (l never heard of anyone doing this) add bites to make it come as longer than the real program as they want, for example 4,096 bytes. Then later if he needs to change something delete some of the extra superfluous stuff if he has enough of it to delete and still make the total file 4,096 bytes.
I have never heard or know of anyone doing that, but is possibly, not likely.
KE4EST
Funny, As I was reading over your post I am right at this moment writing in C. :)
I have been trying to get two boards to talk to each other over I2C. And just accomplished it. :)
...but no you are not offending me, as I am a C programmer and know how it works.
As far as what Ali is doing I am not exactly sure. I have worked with firmware files for years with different receivers.
I know for the older ones like the S9 and S10 the file has to be exactly 4096 kB. For the newer receivers, they have to be 8192 kB.
I only assume this is some sort of error checking and what ever bytes are left are filled with 255's.
electronmini
Funny, As I was reading over your post I am right at this moment writing in C. :)
I have been trying to get two boards to talk to each other over I2C. And just accomplished it. :)
...but no you are not offending me, as I am a C programmer and know how it works.
As far as what Ali is doing I am not exactly sure. I have worked with firmware files for years with different receivers.
I know for the older ones like the S9 and S10 the file has to be exactly 4096 kB. For the newer receivers, they have to be 8192 kB.
I only assume this is some sort of error checking and what ever bytes are left are filled with 255's.
Amaking to see that hyou also proficient with C language and amazing to hear the someone makes a file exactly a predestined number of bytes. I never heard that and "assumed " to be useless and a waste of time to say the least. I was wrong once again!
But I am an old timer and the last time l wrote code in C and Cobol was exactly 21 years ago before retirement.
Thanks for the info and your patience.
Just a while ago I came across the Arduino thingy and started to itch to get into microcontroller, but life is limited and have already too many areas of interest : feel like Jack of all trades, master of none.Plus family, friends, people that needs help,etc,etc.
Thanks for your time and support.
Wilson
. Raine
There's probably a "dummy" file in the firmware package to make it come out to that size.
  • Like
Reactions: electronmini
Peter Parker
Supporting Founder Lifetime Supporter
Last reply · posted in Computers and Gadgets
I have had good experiences with Brave but lately I am frustrated with it.

Now when I launch the app it shows a box at the bottom asking if I want to go back to the last opened page. It is in conveniently located and I would prefer to eliminate it.

Does anyone know how to do this?

Please let's not sidetrack the discussion into an exploration of why I don't care for it or a lecture about all the wonderful aspects of the feature. I just do not care for it.
3 Replies · 59 views
b4pjoe
I don't have an Android phone so I don't know if this will apply to the Brave settings on your android device but it works on the desktop for me.

Change this setting to either startup to a different website or a new tab page. I have mine set to open to google.com instead of where I left off and it doesn't ask me at the next startup if I want to open the last opened page unless it crashed.

Screenshot 2026-06-10 at 6.46.20 PM.webp
Peter Parker
I don't have an Android phone so I don't know if this will apply to the Brave settings on your android device but it works on the desktop for me.

Change this setting to either startup to a different website or a new tab page. I have mine set to open to google.com instead of where I left off and it doesn't ask me at the next startup if I want to open the last opened page unless it crashed.

View attachment 191721
Thank you for trying to help. However thrse choices do not appear in Android. There is a setting for "New Tab Pages" that is similar but does not include your choice. I have tried all of the existing entries with no success
  • Like
Reactions: b4pjoe
Juan
Something like this maybe


Option 2: Set a custom Home button URL
  1. Click the menu icon in the top-right corner and select Settings.
  2. Click on Appearance in the left sidebar.
  3. Toggle on the Show home button switch.
  4. Under the home button settings, select the option to Enter custom web address and type in your preferred website. [1, 2, 3, 4, 5]
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in The Chit Chat Club
Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne


Get it?


An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
67102 Replies · 2662206 views
  • Like
Reactions: c-spand
long_time_DNC
King Of The World - Steely Dan
RaiderPower
King Of The Road - Roger Miller
long_time_DNC
King Of Pain - The Police
  • Like
Reactions: ClarkGable
H
Haven't Got Time For The PAIN-Carly Simon
  • Like
Reactions: ClarkGable
ClarkGable
No Time - The Guess Who
BlackHitachi
Supporting Founder
Last reply · posted in Movie Talk
Since the Reds have there thread we should too!

Last watched Nine inch Nails
Next 3:10 to Yuma
5346 Replies · 509278 views
osu1991
Rooster Cogburn.

Keep forgetting the free movies on youtube are ad free with my premium subscription.
dfergie
Rooster Cogburn.

Keep forgetting the free movies on youtube are ad free with my premium subscription.
There are some really good movies on youtube.
Saving Private Ryan 4k, Dolby Atmos...
harshness
Saving Private Ryan 4k, Dolby Atmos...
These are severely limited. Getting better than stereo audio is improving, but still has a long way to go.
dfergie
These are severely limited. Getting better than stereo audio is improving, but still has a long way to go.
I went with my 4k disc after checking out that version.
osu1991

View: https://youtu.be/I68627xyDPA?is=gUZB0Yv_08pE0DR3


Tonight revisiting one of my favorites. Ranks up there with Star Wars, Raiders of the Lost Ark and Hunt For Red October.
dfergie
Watching Monterey Pop, been awhile, had the DVD, but probably lost in the fire 10.5 years ago. HBOmax
"MysteryMan"
813WnPwdB3L._SX342_.webp
  • Like
Reactions: dfergie
S
· posted in FTA Manuals Section
Looking for a manual. Want to do some radio astronomy with it. Realize it's old but, since it's not for tv use don't need any decoders, just the RF section.
0 Replies · 8 views
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in SatelliteGuys Support Center
Due to security concerns and the fact that the Tapatalk Plugin for Xenforo is no longer being updated we have removed Tapatalk support from SatelliteGuys.

For those who were using it we recommend using our PWA App instead which is faster and does not have all the spam Tapatalk had. Below is a graphic showing how to add SatelliteGuys to your devices home screen. (While iOS is shown the process is mostly the same for Android.)

add_to_home.gif

Thanks for your understanding. :)
5 Replies · 137 views
Foxbat
Thank you, Scott, for adding years to my Life and dropping my BP a few millimeters! Money well spent…
dweber
Thank you, Scott, for adding years to my Life and dropping my BP a few millimeters! Money well spent…
What is PWA app? PWA utilities seem to be a Spanish app. I hope you are seeing this since nothing seems to be working. I will miss SatelliteGuys. Tapatalk worked well. The Siri browser doesn't seem to work well.
  • Like
Reactions: charlesrshell
Peter Parker
Thank you, Scott, for adding years to my Life and dropping my BP a few millimeters! Money well spent…
Hooray!
  • Like
Reactions: charlesrshell
Peter Parker
What is PWA app? PWA utilities seem to be a Spanish app. I hope you are seeing this since nothing seems to be working. I will miss SatelliteGuys. Tapatalk worked well. The Siri browser doesn't seem to work well.
Do you mean the safari browser?
Foxbat
What is PWA app? PWA utilities seem to be a Spanish app. I hope you are seeing this since nothing seems to be working. I will miss SatelliteGuys. Tapatalk worked well. The Siri browser doesn't seem to work well.
Actually, PWA stands for "Progressive Web Application" and is basically just saving a site's homepage to your desktop where it appears as an "App" with the rest of your smartphone's Apps.
1781162703297.webp
  • Like
Reactions: charlesrshell
N5XZS
Last reply · posted in Over the Air Television By RabbitEars.Info
New low power station has been granted by the FCC and the new call leter is K33OB-D on RF ch. 33.

Will run at 15 KW ERP, this one runs from the Westside same location as KWPL-LD a HC2 owned station.

It's going to be aimed at eastern part of Albuquerque, so it's tightly focused beam pattern.

This new station is owned by Digital Network and what kind of programmings is unkown at this time.😎
9 Replies · 122 views
M
This new station is owned by Digital Network and what kind of programmings is unkown at this time
probably the same programming they have been putting on their other owned stations.
The 'get after it media' stations
Like Heartland, Retro, rev'n, Action etc
  • Like
Reactions: dfergie
comfortably_numb
probably the same programming they have been putting on their other owned stations.
The 'get after it media' stations
Like Heartland, Retro, rev'n, Action etc

We already have those diginets here.
N5XZS
Yeah, there are some diginets like Heartland, Retro, The Family Channel diginetworks that we already have here in this market and we don't need duplicates, but bring the new diginets on like the Rev'n, Karate Acton movies, different kind of music videos on the new station. :hatsoff2
  • Like
Reactions: comfortably_numb
comfortably_numb
Yeah, there are some diginets like Heartland, Retro, The Family Channel diginetworks that we already have here in this market and we don't need duplicates, but bring the new diginets like Revn, Karate Acton movies, different kind of music videos on the new station. :hatsoff2

I watch MovieSphere Gold channel a lot. Many recent movies on that digitnet :)
N5XZS
Yes that's a good channel MovieSphere, only thing is the missing CC on it. :rolleyes: :hatsoff2
  • Sad
Reactions: comfortably_numb
comfortably_numb
According to the FCC listing, the tower is near I-40 and Juan Tabo:

R
Last reply · posted in DISH Network Support Forum
Hello everyone.

I am new here and I done a search on MLB Extra Innings and DISH and it led me to this forum and so I signed up and hopefully someone can help me out with some issues.

First off, I am a DISH Outdoors customer and I signed up for service back in late October of 2025. I have a Wally HD Receiver and I am using the DISH Playmaker OS 2.1 as my Antenna that operates on 110 and 119 Western Arc and Alternative 61.5, 110, and 119 satellites. I signed up for MLB Extra Innings back in March before the season began. I was excited to be able to watch MLB Extra Innings because I love baseball and I use to have MLB Extra Innings on Satellite DIRECTV back in 2001-2004 and on Satellite DISH back in 2016 and 2017.

I was a bit disappointed when I found out that it is actually MLB.TV Simulcasted to DISH Satellite (More on that later) Anyways I have been watching faithfully almost every night however about a week ago there was a problem. When I went to go to the game to watch a game the game wouldn't come in an I would send a refresh signal to my receiver and then I could watch the programming and when I went to switch games at that games appointed time slot my Wally HD Receiver who lockup where I couldn't change any channels or view the guide and it would reboot. The next night when I turned to a game at game start it still had the background it shows before the game started and again send a refresh signal and went though this same thing over and over. I added a movie channel to my lineup and had issues with showing up my Dish Wally HD Receiver.

With an investigation after several calls with DISH Support it was determined that by going to the diagnostics screen that I had a issue with my Tuner because any changes that I made to my programming these changes would not take affect on the Wally HD Receiver. In other words that Wally HD Receiver was toast!

I too had reported MLB Extra Innings issue to DISH and they created a ticket for it and said that someone would investigate the issue. I too took notice that under MyDISH account under MLB Extra Innings always before it would show that I was subscribed and on auto-renew. Now it shows nothing and even after logging out and deleting my User Name and Password so that I can see it in guest mode it too doesn't even list a price and option for purchase as does the now WNBA League Pass.

After my DISH Receiver was ruined I had to buy a new Wally HD Receiver. I took advantage an bought 2 HD Wally's and added them both to my account. I called back to remove the old box off of the account and was told it was linked to MLB Extra Innings and the advanced technical support team said there was a glitch with MLB Extra Innings and hope to have a resolution in a couple of days and I could call back in to then to remove the box. But both the 2 new Wally HD Receivers are activated on my account. I asked them what the problem was with MLB Extra Innings and how long it would be and I was told there was a glitch as I asked to specify what they meant and got no answer. I again went and checked the MyDISH account page under the MLB Extra Innings page and it still doesn't list me as subscribed and after logging out and deleting my User Name and Password so I could it see it as a guest mode and it still doesn't list the price and option for purchase as it does for the WNBA League Pass.

I am afraid to boot up these boxes and go through the activation screen process because of the issues with the MLB Extra Innings in fear it will do the same or mess up my boxes from being able to receive MLB Extra Inning because or any other programing because I was told that MLB Extra Innings wouldn't come in on those new box because it was activated with the Wally that is ruined and it needs removed first.

Now I have no DISH service going on a week and miss my MLB Extra Innings when the races are just heating up and now with two boxes activated I can't boot up because I am afraid it will mess them up and I will be out the $180.00 or so dollars I made in purchase on the receivers.

Is anyone else experiencing issues with their MLB Extra Innings and does anyone really know what this so called glitch actually is? I can't seem to get a clear answer from anybody and don't even know if it will even be fixed or anyone really understands it.

Now to my previous statement on how I was disappointed that MLB Extra Innings is actually MLB.TV in simulcast. When I had MLB Extra Innings before with DIRECTV in 2001-2004 and with DISH form 2016 and 2017. They would always show the commercials for every teams broadcast from their local market and all games would be authentic just as if you were watching in their home market. After I quit DISH I went to streaming for awhile and I done MLB.TV and I hated their features because of the no commercials, the delayed times of getting back after the commercial break, and not being able to listen to what studios had to say when they would cut into the studios, and always looking at the screen during commercial breaks with a screen that says commercial break in progress and a silhouette background of MLB Players doing baseball things and the their crazy commercial breaks sound. I was excited to go back to DISH thinking I escaped the horrors of MLB.TV. Well its actually the same thing. I compared them side by side and actually MLB.TV is ahead by just a few seconds. So actually MLB Extra Innings on Satellite is delayed from time period wise from actually watching MLB.TV which shows it is simulcasted. My question is when did this start? And is this legal? This isn't what I know MLB Extra Innings to be. I too had signed up for NHL Center Ice this past winter and thank goodness its authentic! They still have the commercials and its like watching it as you were in their home network and its the way it oughta be even if you only do get one feed of NHL Center Ice per team on DISH and don't know which feed it is every night.

Looking forward to your responses. So far happy with DISH but unhappy with this last week and the ruining of a Wally HD Receiver.

I hope I can be of some contribution here as well.

Sincerely,

RJ T.
From Illinois
8 Replies · 312 views
zippyfrog
I know they are doing some major satellite work - the second satellite at 110 which is now in use, and they are moving channels between 119 and 110. Maybe since there are no other sports going on, have they temporarily cut back on the out of market sports packages? I am not sure. It looks like those channels are all coming from 119 TP 13, 110 TP 12, and 110 TP 09.

Also, Dish's Scheduled Satellite Maintenance page doesn't have anything going on:

R
I know they are doing some major satellite work - the second satellite at 110 which is now in use, and they are moving channels between 119 and 110. Maybe since there are no other sports going on, have they temporarily cut back on the out of market sports packages? I am not sure. It looks like those channels are all coming from 119 TP 13, 110 TP 12, and 110 TP 09.

Also, Dish's Scheduled Satellite Maintenance page doesn't have anything going on:

Trying to get use to this forum and where everything is located at. I saw you responded from my post on the changes and took me a while to get back to see this post. But yes, it is exactly what I was thinking. I too noticed the change of MLB Extra Innings from 110 to 119. Because of 30 teams they have to algin everything. Only other sport going on PPV wise is WNBA League Pass and I do not have a subscription to that but maybe some else who has it can confirm what they done and what satellite and transponders they are on.

This is a big shift for DISH. I just hope if Charlie Ergen does ever sell out to anyone that I can continue to use my DISH Playmaker and I can keep my Wally's. If its anything like what happened to DIRECTV a few years back which turned out to be a total disaster when AT&T acquired DIRECTV nothing there changed with boxes or anything and you continued to use the same service but I was very surprised to see AT&T sell it to TPG especially after they had just bought it now long ago.

RJ T.
From Illinois
R
Hello everyone.

I am new here and I done a search on MLB Extra Innings and DISH and it led me to this forum and so I signed up and hopefully someone can help me out with some issues.

First off, I am a DISH Outdoors customer and I signed up for service back in late October of 2025. I have a Wally HD Receiver and I am using the DISH Playmaker OS 2.1 as my Antenna that operates on 110 and 119 Western Arc and Alternative 61.5, 110, and 119 satellites. I signed up for MLB Extra Innings back in March before the season began. I was excited to be able to watch MLB Extra Innings because I love baseball and I use to have MLB Extra Innings on Satellite DIRECTV back in 2001-2004 and on Satellite DISH back in 2016 and 2017.

I was a bit disappointed when I found out that it is actually MLB.TV Simulcasted to DISH Satellite (More on that later) Anyways I have been watching faithfully almost every night however about a week ago there was a problem. When I went to go to the game to watch a game the game wouldn't come in an I would send a refresh signal to my receiver and then I could watch the programming and when I went to switch games at that games appointed time slot my Wally HD Receiver who lockup where I couldn't change any channels or view the guide and it would reboot. The next night when I turned to a game at game start it still had the background it shows before the game started and again send a refresh signal and went though this same thing over and over. I added a movie channel to my lineup and had issues with showing up my Dish Wally HD Receiver.

With an investigation after several calls with DISH Support it was determined that by going to the diagnostics screen that I had a issue with my Tuner because any changes that I made to my programming these changes would not take affect on the Wally HD Receiver. In other words that Wally HD Receiver was toast!

I too had reported MLB Extra Innings issue to DISH and they created a ticket for it and said that someone would investigate the issue. I too took notice that under MyDISH account under MLB Extra Innings always before it would show that I was subscribed and on auto-renew. Now it shows nothing and even after logging out and deleting my User Name and Password so that I can see it in guest mode it too doesn't even list a price and option for purchase as does the now WNBA League Pass.

After my DISH Receiver was ruined I had to buy a new Wally HD Receiver. I took advantage an bought 2 HD Wally's and added them both to my account. I called back to remove the old box off of the account and was told it was linked to MLB Extra Innings and the advanced technical support team said there was a glitch with MLB Extra Innings and hope to have a resolution in a couple of days and I could call back in to then to remove the box. But both the 2 new Wally HD Receivers are activated on my account. I asked them what the problem was with MLB Extra Innings and how long it would be and I was told there was a glitch as I asked to specify what they meant and got no answer. I again went and checked the MyDISH account page under the MLB Extra Innings page and it still doesn't list me as subscribed and after logging out and deleting my User Name and Password so I could it see it as a guest mode and it still doesn't list the price and option for purchase as it does for the WNBA League Pass.

I am afraid to boot up these boxes and go through the activation screen process because of the issues with the MLB Extra Innings in fear it will do the same or mess up my boxes from being able to receive MLB Extra Inning because or any other programing because I was told that MLB Extra Innings wouldn't come in on those new box because it was activated with the Wally that is ruined and it needs removed first.

Now I have no DISH service going on a week and miss my MLB Extra Innings when the races are just heating up and now with two boxes activated I can't boot up because I am afraid it will mess them up and I will be out the $180.00 or so dollars I made in purchase on the receivers.

Is anyone else experiencing issues with their MLB Extra Innings and does anyone really know what this so called glitch actually is? I can't seem to get a clear answer from anybody and don't even know if it will even be fixed or anyone really understands it.

Now to my previous statement on how I was disappointed that MLB Extra Innings is actually MLB.TV in simulcast. When I had MLB Extra Innings before with DIRECTV in 2001-2004 and with DISH form 2016 and 2017. They would always show the commercials for every teams broadcast from their local market and all games would be authentic just as if you were watching in their home market. After I quit DISH I went to streaming for awhile and I done MLB.TV and I hated their features because of the no commercials, the delayed times of getting back after the commercial break, and not being able to listen to what studios had to say when they would cut into the studios, and always looking at the screen during commercial breaks with a screen that says commercial break in progress and a silhouette background of MLB Players doing baseball things and the their crazy commercial breaks sound. I was excited to go back to DISH thinking I escaped the horrors of MLB.TV. Well its actually the same thing. I compared them side by side and actually MLB.TV is ahead by just a few seconds. So actually MLB Extra Innings on Satellite is delayed from time period wise from actually watching MLB.TV which shows it is simulcasted. My question is when did this start? And is this legal? This isn't what I know MLB Extra Innings to be. I too had signed up for NHL Center Ice this past winter and thank goodness its authentic! They still have the commercials and its like watching it as you were in their home network and its the way it oughta be even if you only do get one feed of NHL Center Ice per team on DISH and don't know which feed it is every night.

Looking forward to your responses. So far happy with DISH but unhappy with this last week and the ruining of a Wally HD Receiver.

I hope I can be of some contribution here as well.

Sincerely,

RJ T.
From Illinois
Update on MLB Extra Innings as of 5:50 P.M. CDT June 10, 2026...

I am getting tired of not being able to watch any baseball games and having paid for MLB Extra Innings and not knowing what the reason is I called dish back at 1-800-333-3474. I guess after all of my calls my call was routed to the Advanced Technical Support Team. I had something happen that I never knew they could do and they gained access into my Wally Receiver. I was told settings look good and right now on the only channel that shows is the MLB1 Baltimore Orioles Channel. They are playing the at home against the Seattle Mariners right now. She was able to access to that channel which prompted a purchase a Rent option. That signaled a red flag to her right away. She escalated a ticket with photographs and info from my screen to the top tier advanced programing technical department and told me they received the ticket and are reviewing it now. They got back to her and said they would have information within 30 minutes. I either get the channels within 30 minutes or I am to call back and they will advance from there. Seems like maybe my persistence is paying off. I will keep you informed. Maybe we can all have a resolution to this shortly.

RJ T.
From Illinois
R
Update on MLB Extra Innings as of 5:50 P.M. CDT June 10, 2026...

I am getting tired of not being able to watch any baseball games and having paid for MLB Extra Innings and not knowing what the reason is I called dish back at 1-800-333-3474. I guess after all of my calls my call was routed to the Advanced Technical Support Team. I had something happen that I never knew they could do and they gained access into my Wally Receiver. I was told settings look good and right now on the only channel that shows is the MLB1 Baltimore Orioles Channel. They are playing the at home against the Seattle Mariners right now. She was able to access to that channel which prompted a purchase a Rent option. That signaled a red flag to her right away. She escalated a ticket with photographs and info from my screen to the top tier advanced programing technical department and told me they received the ticket and are reviewing it now. They got back to her and said they would have information within 30 minutes. I either get the channels within 30 minutes or I am to call back and they will advance from there. Seems like maybe my persistence is paying off. I will keep you informed. Maybe we can all have a resolution to this shortly.
R
Update on MLB Extra Innings as of 5:50 P.M. CDT June 10, 2026...

I am getting tired of not being able to watch any baseball games and having paid for MLB Extra Innings and not knowing what the reason is I called dish back at 1-800-333-3474. I guess after all of my calls my call was routed to the Advanced Technical Support Team. I had something happen that I never knew they could do and they gained access into my Wally Receiver. I was told settings look good and right now on the only channel that shows is the MLB1 Baltimore Orioles Channel. They are playing the at home against the Seattle Mariners right now. She was able to access to that channel which prompted a purchase a Rent option. That signaled a red flag to her right away. She escalated a ticket with photographs and info from my screen to the top tier advanced programing technical department and told me they received the ticket and are reviewing it now. They got back to her and said they would have information within 30 minutes. I either get the channels within 30 minutes or I am to call back and they will advance from there. Seems like maybe my persistence is paying off. I will keep you informed. Maybe we can all have a resolution to this shortly.

RJ T.
From Illinois
Update as of 6:40 P.M. CDT June 10, 2026...

Noting went through on my screen. However take a look at this


They have the page back up but it shows I need to purchase. On phone on hold waiting to connect to get this thing activated.

Will post shortly with update.

RJ T.
From Illinois
R
Update as of 6:40 P.M. CDT June 10, 2026...

Noting went through on my screen. However take a look at this


They have the page back up but it shows I need to purchase. On phone on hold waiting to connect to get this thing activated.

Will post shortly with update.

RJ T.
From Ill

Update as of 6:40 P.M. CDT June 10, 2026...

Noting went through on my screen. However take a look at this


They have the page back up but it shows I need to purchase. On phone on hold waiting to connect to get this thing activated.

Will post shortly with update.

RJ T.
From Illinois
Final Update... As of 8:08 P.M. CDT June 10, 2026.

I now have MLB Extra Innings back! Look at the photo! (I did not include full image of the game due to copyright)

Let me just say it was rough! Very rough! And lets just say Charlie Ergen should be ashamed of his customer service team and how they handled this whole issue.

After multiple calls after my last post only to get the run around with answers like there are no refunds on MLB Extra Innings once the season starts, to they are working on it, to accessing my screen and sending multi hits to the box.

All I asked was one simple question remove the MLB Extra Innings which they confirmed I had and reauthorize free of charge. I was given a 1,000 reasons why this couldn't be done.

Well..........

I paid for it myself.... $120.00 current rate and it works!

I called back in to let them know what I done and what I thought of the customer service and told them I needed refunded. I was told they didn't do refunds....

Well again I called back and got someone who refunded the original payment of $150.00 back to my account. A $30 discount for all the hard trouble I went though.

It is now up to you all out there that have MLB Extra Innings to try to get them to do this but I am afraid you are going to have to take your own action and purchase again and beg for a refund or be out the $150.00 originally paid.

Persistence pays off. I don't give up very easily.

You can all go here below to make the purchase if you have any trouble.


I hope it all works well for you! And best of luck to everyone who has it!

I will still be around on this forum. You all sound like a fine group of people! I hope I can contribute more.

Take care!

RJ T.
From Illinois