Social Feed

Technojunky

Last reply Nov 20, 2005 · posted in Free To Air (FTA) Discussion

Fortec Lifetime Ultra Motor settings reset??

I finaly got my Stab HH90 motor to work in a decent way. The problem came when I came accross a problem that PBS helped me with, it was how to reset the Fortec receiver. The reset was needed to combat a problem where certain chanels would cause the receiver to lock and reset itself. I had just gotten the feeling of success when I succesfully scanned three seperate satellites and they all looked very good.

The problem: I reset the receiver and I now can not get past the true south satellite that I zeroed on. This would be 79 degrees, Amsat-5. What I can do , it select reference and get Amsat-5 with not problem. I set my coordinates, and save my positon. When I go to the next satellite, Nimiq-1/3, it no longer works. I didn't change any positoon on the dish itself, I jsut select USALS and set the proper LNB and it never finds it. It was working before the reset, but not now.

Is there a way to resync my receiver so more than my reference satellite works?

Stumped again.. Joe

12 Replies · 2738 views

Load Replies (12) Reply Legacy View

Technojunky

Nov 18, 2005

I had my receiver on a satellite and receiving some channel that I wasn't actually watching. I left it on for a few hours while I was doing other things. When I went back into the bedroom, the TV showed 'No Signal'. I checked the antenna settings and it was set for USALS and was OK the last time I checked. I coudl not get the DISH to move back to the satellite I was on, so I went to my true south bird and it would not go there either. I turned the receiver power off and back on, and it worked normal again. Is this something that has happened to any of you? Should it concern me? It has been working OK for the last few hours now.

PSB

Nov 18, 2005

Only a problem if it keeps happening, I have to do it on average of about once a month.

Sadoun

Nov 20, 2005

Technojunky

Moving the motor to 0 then aiming at your True South satellite will work only if your LONGITUDE is exactly equals to the LONG of the satellite. If the satellite is off by a fraction of a degree, that will through your satellite ARC out of alignment.

The best way to aim a motorized dish is to use the USALS feature in your receiver. Simply:
1- Adjust your motor and dish angles according to proper calculations
2- Use the USALS feature in your receiver to enter your latitude & Longitude.
3- Select one of the active satellites that is close to your longitude (true south)
4- With the motor at 0 position, aim your dish assembly to your TUE SOUTH angle using a good compass.
5- Use the MOVE to satellite command in your receiver's USALS menu to make the motor move the dish the proper amount.
6- Watch the screen for Signal AND Quality.
7- If no quality, then stand behind the motor. Hold the motor body with both hands and try to turn it East or West a few degrees (very very slowly). You don't want to be too far away from the TRUE SOUTH position.
8- IF you get QUALITY, then maximize it and stop moving the motor. Adjust the dish elevation slightly to get the max quality.

Good luck.

Technojunky

Nov 20, 2005

Your instructions appear to be what I did. In every instance, I can go back to my true south and get it. The motor wants to go back to zero whenever the receiver is reset. I always can count on this when I reset my receiver.
The problem comes when I tell the motor to take me to one of the other satellites, it sometimes will, but will not always stay there. In some cases, I can't get the motor to move unless I power my receiver off and back on. I am running through a pair of diplexers, and they appeared to work with my old motor just fine. This Stab motor worked fine when I was on a short coax to install it, the problems started when I went inside. I run through over 100 feet of coax, and 75 feet of it before the first diplexer, then about 40 feet more before the next diplexer, then 10 feet more to the receiver.

I may try to elminate diplexers from my setup. there might be a chance that i can shorten the run of coax too. I just did a complete factory reset again, and locked onto my true south in two seconds. Then I sent the motor to another satellite and it went to it with no problem. It is this good behavior, followed by odd , confused behavior that makes me think that something is wrong.

Thanks for the help, it was very clear and easy to follow. The steps that confused me a little were 4 and 5. When I set my true south satellite, I do not use the Move to satellite. I picked my true south bird, 79 degree's, then set my angle, and turn the motor (while it is set to zero), to hit the 79 degree bird. Once I am pointed at 79 degrees with good quality, I store it. Where am I going wrong?

Let's say that I reset my receiver again and the dish is at zero, and pointing to 79 degrees. I have good quality at zero (motor)= (79 degree's). What is the next step? What am I doing wrong?

Joe

Tron

Nov 20, 2005

Is there a way on the HH90 to reset the motor?

I would move the motor to '0', reset it, and reset the receiver. This often helps with problems on an SG-2100...

View all replies (12)

Former member 209992

Last reply 15 minutes ago · posted in SatelliteGuys Support Center

Site is slooooow

For some reason, the satelliteguys.us site is loading a lot slower than usual on both Chrome on my Asus laptop and Safari on my iPhone.
I'm also seeing longer appearances of the blue bar at the top and the "3 blue bars" loading symbol.
Is anyone else also having the same problem? Thanks in advance.

547 Replies · 18856 views

Load Replies (547) Reply Legacy View

Reactions: charlesrshell

Foxbat

Today at 2:07 PM

I saw that, wasn't sure if PHP was employed by XenForo or not.

PHP warns it plans to release 2 emergency patches imminently

Unconfirmed report claims PHP2Shell exploit remotely executes code on PHP sites.

arstechnica.com

Reactions: charlesrshell

Scott Greczkowski

Today at 2:08 PM

Yup thats what xenforo is written in, php.

But all patched now.

Reactions: FTA4PA, Foxbat and charlesrshell

harshness

27 minutes ago

Foxbat said:
I saw that, wasn't sure if PHP was employed by XenForo or not.

PHP and a heapin' helpin' of JavaScript.

As dated as it is, PHP is eminently adept at projects like a forum. With modules, it is competitive in flexibility and computational efficiency with tools like Node.js or Ruby (where you must choose from many outboard tools).

Reactions: charlesrshell

comfortably_numb

24 minutes ago

Related to this?

Critical Flaw Found By AI Puts 70% Of World’s Websites At Risk

www.huffpost.com

Reactions: charlesrshell

harshness

15 minutes ago

More specifically, these:

https://www.cve.org/CVERecord?id=CVE-2026-109618

https://www.cve.org/CVERecord?id=CVE-2026-109619

A more scholarly story is here:

PHP warns admins of two critical flaws, emergency patches coming tomorrow

The PHP security team is warning administrators to prepare for emergency security updates tomorrow to address two critical vulnerabilities, as information about the flaws has reportedly leaked ahead of their scheduled disclosure.

www.bleepingcomputer.com

View all replies (547)

dishstaller

Pub Member / Supporter Lifetime Supporter

Last reply 16 minutes ago · posted in The Chit Chat Club

You can't even trust the cost per ounce info in grocery stores anymore

I'm surprised Walmart hasn't banned this guy from all of their stores. He has been on their CASE the past few months.

View: https://www.youtube.com/shorts/f3zr37ekgKM?feature=share

10 Replies · 76 views

Load Replies (10) Reply Legacy View

Juan

Today at 11:17 AM

dishstaller said:
I'm surprised Walmart hasn't banned this guy from all of their stores. He has been on their CASE the past few months.

View: https://www.youtube.com/shorts/f3zr37ekgKM?feature=share

When walmart set a price...they weigh the container and the product...the product label only shows the weight of the product...I am sure if you brought your own plastic baggies to bring the product home you could get the cheaper price

dishstaller

Today at 11:47 AM

Juan said:
When walmart set a price...they weigh the container and the product...

Then they are stupid. Everyone knows that the price per ounce should be the price per ounce of actual product.

b4pjoe

Today at 12:41 PM

Meat with a bone in it. It contributes to the weight.

harshness

Today at 12:57 PM

b4pjoe said:
Meat with a bone in it. It contributes to the weight.

Bone-in is a well-known and often prized attribute. Adding the tray and the film isn't right.

Reactions: dishstaller

Juan

Today at 1:38 PM

dishstaller said:
Then they are stupid. Everyone knows that the price per ounce should be the price per ounce of actual product.

You are paying for the whole thing

telstar_1

Today at 2:22 PM

Juan said:
You are paying for the whole thing

Well, the bag can't weigh that much, right? But by law food product packaging must display the actual net weight of the product, i.e., the contents of the container, so by any logic, if not law, a store's stated per-ounce cost should reflect that figure. But since there's not any law regulating shelf statements, a store can say whatever it wants without violating any rules. So I guess the answer is more consumer legislation. Or simply caveat emptor.

Juan

21 minutes ago

telstar_1 said:
Well, the bag can't weigh that much, right? But by law food product packaging must display the actual net weight of the product, i.e., the contents of the container, so by any logic, if not law, a store's stated per-ounce cost should reflect that figure. But since there's not any law regulating shelf statements, a store can say whatever it wants without violating any rules. So I guess the answer is more consumer legislation. Or simply caveat emptor.

But a box can weigh more than an ounce..maybe 2...a can might weigh 5 ounces..a bag...not much

dishstaller

16 minutes ago

Juan said:
.a bag...not much

Well, according to the price per ounce on that first bag of coffee he mentions, that would mean the bag weighed over 6 ounces. That bag does NOT weigh 6 ounces. According to Google, an empty bag weighs half an ounce.

View all replies (10)

Scott Greczkowski

Staff member HERE TO HELP YOU! Cutting Edge

Last reply 28 minutes ago · posted in The Chit Chat Club

Song Name Game Part 3!

Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne

Get it?

An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....

68563 Replies · 2675205 views

Load Replies (68563) Reply Legacy View

Reactions: c-spand

harshness

Today at 11:08 AM

I Don't Wanna Miss a Thing - Aerosmith

Reactions: dishstaller

Bobby

Today at 11:20 AM

Good Golly, Miss Molly - Little Richard

Reactions: sdfntx, RaiderPower and gms49ers

dishstaller

Today at 11:42 AM

Little Miss Dangerous - Ted Nugent

RaiderPower

Today at 1:24 PM

Little Miss Can't Be Wrong - Spin Doctors

sdfntx

28 minutes ago

Jump Down, Spin Around - Harry Belafonte

Reactions: Bobby

View all replies (68563)

Anony55

Last reply 34 minutes ago · posted in DISH Network Support Forum

DISH Has Made it Impossible to be a VIP211k Owner

For quite a while now, people with a VIP211k have been losing their recordings on their activated external HDDs... even when there's nothing physically wrong with HDD. I believe this is an intentional and underhanded tactic that Dish is pulling in an attempt to force users away from the VIP211k.

They are obviously regretting that they ever let users have a "non-dvr" dvr in the first place. You would think they would be happy charging you a $40 one time fee... and then be happy letting the customer be the one responsible for HDD failures.

Dish clearly hates the 211k bitter-clingers. This recording deletion problem is intentional (IMO), and I think it is just one more tool that they are using. Hopper and a 2-year agreement... that's what they want you to have. Think about that... a 2-year agreement... with a company $30 Billion in debt (that's with a B). What happens when all that debt causes them to drop the channel that may have been your whole reason for having Dish in the first place? Guess who's stuck with a service that no longer suits their needs... for the remainder of the 2-year agreement.

On top of that, they don't want you to install it yourself. I purchased and installed all my equipment myself. That used to be common. Now, they lie to me and tell me that my dish must be updated to use a Hopper. Funny thing is... they don't even know what dish I have because they didn't install it, and I didn't tell them. If you ask what type of dish/LNBs the hopper needs... good luck getting an answer. All they know is that whatever you have needs to be upgraded by an installer.

It is quite apparent to me that they care much more about staying in their box, than they do working with the customer. That's too bad, because it hasn't always been that way. It's like they are totally unaware of the current business environment that they are trying to compete in.

I have been a customer since 2010. I will be cancelling my service before the next period. Yeah, I know, my $1,200 a year won't make a difference to them. It just seems like they have forgotten who needs who, especially when you consider the competition in today's streaming world. But hey, they will have succeed in forcing me off the 211k.

169 Replies · 7739 views

Load Replies (169) Reply Legacy View

Reactions: Former member 208119, JSheridan and charlesrshell

Nebugeater

Dec 22, 2025

Got a 211k that works fine, and I no longer need it if someone wants to throw me a few bucks and pay shipping. Not tied to my account as of last week. Used with a tailgater and got a wally

Reactions: Foxbat, dishdude and charlesrshell

tparker

Sep 30, 2026

Nebugeater said:
Got a 211k that works fine, and I no longer need it if someone wants to throw me a few bucks and pay shipping. Not tied to my account as of last week. Used with a tailgater and got a wally

Is the 211k still available? If so, I'm interested.

Reactions: charlesrshell

Nebugeater

Oct 2, 2026

tparker said:
Is the 211k still available? If so, I'm interested.

Actually, it is. A couple of people PMed me when I posted this, and when I asked for an address, they never responded. Then I just sort of let it go. Send me a PM to continue the discussion

Reactions: Foxbat and charlesrshell

dishstaller

Friday at 11:31 AM

Nebugeater said:
Actually, it is. A couple of people PMed me when I posted this, and when I asked for an address, they never responded. Then I just sort of let it go. Send me a PM to continue the discussion

Unless things have changed at Dish, which is entirely possible, they won't activate the 211, even as a replacement. I gave one to a customer a while back....which when I turned it off I made sure to tell the CSR I wanted it freed up so another customer could use it, I was assured it was.....and when they called to swap out there's they were told it couldn't be done. Now like I said, things MIGHT HAVE CHANGED.

Reactions: Anony55 and charlesrshell

Anony55

Friday at 4:19 PM

dishstaller said:
Unless things have changed at Dish, which is entirely possible, they won't activate the 211, even as a replacement. I gave one to a customer a while back....which when I turned it off I made sure to tell the CSR I wanted it freed up so another customer could use it, I was assured it was.....and when they called to swap out there's they were told it couldn't be done. Now like I said, things MIGHT HAVE CHANGED.

It hasn't changed. When I cancelled my service the other day, they told me I didn't need to return the receiver (which I already knew because I purchased it).

But in addition to that, the young man told me not to sell it, but to take it to a recycling place. The reason he gave for the advice was because 211Ks can no longer be activated.

So as far as the VIP211k goes... once grandpa dies, he's dead.

Reactions: MikeD-C05, charlesrshell and dishstaller

telstar_1

Friday at 5:37 PM

They tell you to trash it and not to sell simply because they're phasing them out, not particularly because someone might be "confused" into buying it and not be able to activate. They tell people that in every case where they're not acting to get a box back, either from a replacement or service cancel.

Reactions: MikeD-C05 and charlesrshell

Corrado

Friday at 7:40 PM

Although my VIP211K hasn't been subscribed or connected to a dish in probably 5 years since canceling service, my 1 TB HDD full of programming still works fine.

Upon occasion I power it up to watch something I recorded as far back as 2010. The last time I had it going in September it even let me rescan the local OTA channels which I think it refused at some earlier time. I will use it until the day it fails but this topic makes me think some software download is responsible for current subscribers.

Reactions: Anony55, MikeD-C05 and charlesrshell

Anony55

34 minutes ago

Corrado said:
Although my VIP211K hasn't been subscribed or connected to a dish in probably 5 years since canceling service, my 1 TB HDD full of programming still works fine.

Since it hasn't been connected to a dish in that long, it probably missed the firmware update that they designed to cause the problem.

Reactions: dishstaller and charlesrshell

View all replies (169)

SuperDish_Fan23

Last reply 54 minutes ago · posted in DISH Network Support Forum

Its crazy how the ViP922 is so rare for no reason.

Why are ViP922s So rare? like its crazy how ebay has none, i checked everywhere, also, i got a ViP222k now, which is actually activated!

10 Replies · 348 views

Load Replies (10) Reply Legacy View

HipKat

Monday at 8:55 AM

I think they were more of a transitional receiver bridging the VIPs to the Hopper. They were a PITA to install and were buggy. Personally, I thought at the time that they were the best receiver out there. The versatility of the VIP's with the new Hopper GUI and, by far, the coolest-looking front plate and lighting.

Reactions: scoob83, Foxbat and charlesrshell

telstar_1

Monday at 1:22 PM

HipKat said:
I think they were more of a transitional receiver bridging the VIPs to the Hopper. They were a PITA to install and were buggy. Personally, I thought at the time that they were the best receiver out there. The versatility of the VIP's with the new Hopper GUI and, by far, the coolest-looking front plate and lighting.

I don't recall that they came out just before hopper, but rather that they came out even before 722. Or could be thinking of 921.

As to the title pf the post, "rare" does not necessarily mean valuable or desirable.

Reactions: MikeD-C05, Mr Tony and charlesrshell

Nominal

Monday at 4:30 PM

telstar_1 said:
I don't recall that they came out just before hopper, but rather that they came out even before 722. Or could be thinking of 921.

As to the title pf the post, "rare" does not necessarily mean valuable or desirable.

You are thinking of the 921. The 922 was the first DVR with Sling functionality built in (that was eventually disabled along with the Sling Adapter for the 722s and the 1st Hopper because they relied on now-defunct Adobe Flash technology). With the bugginess described by others and the removal of its marquee feature (Sling) the 922 faded into obscurity once the Hopper 2 with built in Sling was released and they finally made the concept into a fully functional product.

Reactions: AZ., MikeD-C05, HipKat and 1 other person

dishdude

Monday at 5:05 PM

I had one, the front panel lighting was cool, the menus were fresh and a lot more modern looking than the ViPs. However, it was very buggy and the Sling functionality just didn't work well - I think it was due to internet speeds at the time. I think I had to pay $40 for the Sling app on my phone iirc.

Reactions: AZ. and charlesrshell

MikeD-C05

Today at 1:10 PM

dishdude said:
I had one, the front panel lighting was cool, the menus were fresh and a lot more modern looking than the ViPs. However, it was very buggy and the Sling functionality just didn't work well - I think it was due to internet speeds at the time. I think I had to pay $40 for the Sling app on my phone iirc.

I had both the 921 and the 922. I used to buy them from DishDepot.com in Florida and trade in my older owned receiver towards the newest receiver. The 921 was a reboot receiver and the sling part was hit or miss. I look back on all those receivers I paid for over 25 years and I think it was just TV. If I had that money back now I would be lot richer. My Owned Hopper 3 is sitting in a drawer in my office not being used.

Reactions: dishdude and charlesrshell

telstar_1

Today at 1:33 PM

That was part of the Ergen scheme, to sell the product as well as the service. And who didn't want the best box?

Maybe they went to the hopper because they were running out of 3-digit model #s- 1022 would have been kinda clunky. Folks would have tried to say "one-thousand and twenty two" instead of "ten-twenty-two".

Like some say "two thousand and twenty six".

Reactions: charlesrshell

Strega

54 minutes ago

That's not really unusual. Cable companies like to the provide the box too. The phone company provided the phones in until the government forced them to allow third-party phones.

Reactions: charlesrshell

View all replies (10)

TWiT Tech Podcast Network

Today at 2:12 PM · posted in TWiT Tech Podcast Network

Windows Weekly 1006

Time for another AWESOME video from the TWIT Network!

View: https://www.youtube.com/watch?v=IDlKhq4TMbc

Direct YouTube Link - Windows Weekly 1006
TWIT's Website
TWIT Live Feed

0 Replies · 4 views

Replies Reply Legacy View

reubenray

Last reply Today at 1:17 PM · posted in DISH Network Support Forum

Dish vs Streaming Apps?

Every time my Dish contract comes up I weigh the options of keeping Dish or switch to streaming. Right now I can watch/record the OTA channels vis my HDHomerun. I also can stream CBS and NBC via the Paramount+ and Peacock apps. What I would need to find is how to watch the Food Network, HGTV, Syfy, USA, Hallmark channels, Great American Family, Lifetime channels plus a few more with an app or two. My current Dish bill is $118, so I should be able to get a few apps for a lot less.

Any suggestions? I would want the best picture quality and audio quality I could get.

1 Replies · 62 views

Load Replies (1) Reply Legacy View

Bruce

Today at 1:17 PM

reubenray said:
Every time my Dish contract comes up I weigh the options of keeping Dish or switch to streaming. Right now I can watch/record the OTA channels vis my HDHomerun. I also can stream CBS and NBC via the Paramount+ and Peacock apps. What I would need to find is how to watch the Food Network, HGTV, Syfy, USA, Hallmark channels, Great American Family, Lifetime channels plus a few more with an app or two. My current Dish bill is $118, so I should be able to get a few apps for a lot less.

Any suggestions? I would want the best picture quality and audio quality I could get.

USA and SyFy content is on Peacock, you can receive the rest of those channels via Philo, only $25 a month.

Philo - Stream Live and On-Demand TV

Why pay more for TV? Start your Philo free trial and enjoy live TV plus on-demand content starting at just $25/month. Stream hit shows, movies, and more.

www.philo.com

Reactions: Bobby, osu1991, reubenray and 1 other person

dfergie

Staff member HERE TO HELP YOU!

Last reply Today at 11:26 AM · posted in The Chit Chat Club

Gas Price Info With National Gas Temperature Map

Stumbled across this ... http://www.gaspricewatch.com/USGas_ZipSearch.asp
I found no local prices, although it did show stations at my location...
Added these to this post...
USA National Gas Temperature Map
State By State Gasoline Taxes
Gas Buddy

Ethanol Free Stations

5561 Replies · 461029 views

Load Replies (5561) Reply Legacy View

harshness

Sunday at 11:30 AM

I wonder if California is getting into the Winter formula.

harshness

Yesterday at 5:32 PM

harshness said:
I wonder if California is getting into the Winter formula.

It turns out I was justified in my suspicion.

Gavin Newsom somehow authorized the temporary move of the distribution date of the Winter blend to September 28th.

Foxbat

Yesterday at 8:39 PM

harshness said:
It turns out I was justified in my suspicion.

Gavin Newsom somehow authorized the temporary move of the distribution date of the Winter blend to September 28th.

Does that raise, or lower, the overall price? Our State Government has been doing everything it can to minimize the impact of the current situation and put a freeze on the State Taxes on fuel sales at the pump. That's why we're still under $4.00/gal. while across the border in Michigan it's much higher.

Bobby

Yesterday at 9:05 PM

Foxbat said:
Does that raise, or lower, the overall price? Our State Government has been doing everything it can to minimize the impact of the current situation and put a freeze on the State Taxes on fuel sales at the pump. That's why we're still under $4.00/gal. while across the border in Michigan it's much higher.

Winter blend is cheaper than Summer blend.

Reactions: dishstaller and Foxbat

Bobby

Today at 11:21 AM

Regular$5.839
Premium$6.299
Diesel$7.999
at Costco, Rohnert Park.

harshness

Today at 11:26 AM

Foxbat said:
Does that raise, or lower, the overall price?

Winter blend is reportedly 10-30 cents cheaper, but I would point out that prices have dropped as much as 62 cents at RP.

Reactions: Foxbat

View all replies (5561)

Booredatwork.com

Today at 10:52 AM · posted in BooredAtWork.COM

iPhone Duo Folio Kickstand Case!

Time for another AWESOME video from BoredAtWork!

View: https://www.youtube.com/shorts/RTpsyCQSAgA

Direct YouTube Link - iPhone Duo Folio Kickstand Case!
Booredatwork.com Website
Booredatwork on Facebook

0 Replies · 10 views

Replies Reply Legacy View

Gary Toma

Staff member Pub Member / Supporter Cutting Edge

Last reply Today at 10:40 AM · posted in DIRECTV Technical Resources Forum

DIRECTV Transponder Map ~ Data 10/14/2026

The TPN Map Excel Presents all DIRECTV Channels:

National (50-States or wide/NAT+PR beams)
Local (Local-Into-Local or narrow/Spot beams)

Additional tabs provide:

OTA the (Over-The-Air) Database
VOD (Video On_Demand) Records
Offline Records
Engr Records
Net Decoder a graphic presentation of all satellites and transponders

Domestic Satellites
@99W...... D11, D14
@101W.... D16
@103W.... D12, D15
@110W.... D5
@119W.... D8

Understanding the TPN Map

Making Sense of the TPN Map Display Conventions

DIRECTV_TPN_Map_261014.xlsx 1,874 KB

2147 Replies · 934915 views

Load Replies (2147) Reply Legacy View

Reactions: Zakdj, Mr Tony, Tom Speer and 3 others

KyL416

Yesterday at 2:37 PM

WCWW/25 CW South Bend and WBKP/5 CW Marquette are now testing on the stream server. These are both already available on satellite.

Now live in the satellite guide:
663-2 PISTONS (663-1 is likely being reserved for an overflow feed of Detroit Sportsnet, if there's a 2027 MLB season)
675 THUNDER
693 CLIPPERS

Reactions: Mr Tony

doctor J

Today at 7:22 AM

DirecTV Satellite Transponder Updates for Oct 21 2026

Comparison of Transponder Data for Oct 21 2026 vs Oct 14 2026:

No changes in system tables for any transponder tuning parameters.

Changes to the use of defined transponders:

1 Transponder cleared of all Streams::
Net 10 TID 126 Beam NAT is a National Transponder on D11@99cb, TPN 3

1 Previously unused Transponder with current APG records::
Net 15 TID 15 Beam NAT is a National Transponder on D12@103ca, TPN 16

Stream (PID) counts:

LIVE Streams	National		Spot Beams
	Count	Change	Count	Change
4K	4
HD	264	2	1449
SD mpeg4	145		194
SD mpeg2	433
RB
Audio	89
Push	26
Slate	19		1

TEST Streams	National		Spot Beams
	Count	Change	Count	Change
4K
HD			1
SD mpeg4
SD mpeg2
RB
Engr Work	38	-2

The PID count Excel workbook provides much more count detail.

Newly updated tables of Streams on each transponder are available in the DataDigesters TPN Grids

More details of changes in individual channels will follow in the Weekly Analysis
and Gary Toma's Domestic TPN Map Excel files

NBA Updates
Weekly Analysis soon
Enjoy
DataDigesters

doctor J

Today at 7:23 AM

weekly Analysis for 10/21/2026:

Weekly_Analysis_261021.xlsx 16 KB

KyL416

Today at 7:25 AM

HAWKS, HORNETS, GRZZLIES, HEAT, MAGIC, CAVLIERS, TWOLVES, BUCKS, PACERS and SPURS channels have also been added, however they are pointing to a TV Promise slate, which says they are working with DAZN and others to strike a deal for those teams.

Some more TPN swaps

Mr Tony

Today at 10:40 AM

KyL416 said:
HAWKS, HORNETS, GRZZLIES, HEAT, MAGIC, CAVLIERS, TWOLVES, BUCKS, PACERS and SPURS channels have also been added, however they are pointing to a TV Promise slate, which says they are working with DAZN and others to strike a deal for those teams.

Some more TPN swaps

Wait…..
So even though DAZN keeps touting 'only way to see games' if you are a subscriber to Choice (like my stepdad) if an agreement is reached he can see the Wolfies on 668?
I know the Wild are in dispute and a slate is on 668-1.

View all replies (2147)

Top

Back