Social Feed

iceshark

Last reply Apr 12, 2006 · posted in DISH Network Support Forum

622 Installed today pics and comments

Well at about 715pm they indy installer showed up. His name Jeremy. Very nice guy and very apologetic for being so late. I told him is was all good. Just happy to see him.

He went to work right away. He put up new DPPlus dual on my Dish 500 for 110-119. Then wasted no time with a lousy dish 1000 and put up a separate Dish 500 wing for 129.

Then just as promised pulled out a shiny new DPP-44

Took down my DP-34 and said I could have it. I said you keep it. He was very appreciative.

He peaked sats and did great job with wires. All in all this part took him about 20 minutes.

Said he has had some fix jobs that were scheduled for an hour that took much more and he was an hour or more drive from last job. Said he gets lots of Dish nets weekend and overflow jobs. Seem Dishnet may not actually install on Sat and SUn in my area and farms out to indy contractors.

In my cast I feel very lucky to have gotten such a true pro. He knew what to do and did it. Very clean job.

Then to the inside. We put the power inverter for the 44 at the 622. Also I plugged in my big Channel master dual fly swatter off air antenna on my roof.

Checked signal and 129 was at 76-79 YES!!!!!! He said it was the highest he had seen yet in our Seattle footprint. He said if he used the 1000 it would be about 46-56 at best. Lots of fade. I still am going to convert 129 to my old Voom 30 inch dish. Hopefully the DP rectangle LNB from Microtel will work with the Dishproplus setup already into the 44.

Got on phone with dish and the tech was in AMERICA and was nice. He did try and charge me for DVR for my 508. Had to check with supervisor to make sure it was free. He came back and said yes.

Total charges 49.95 for HD silver
5.95 for Locals
5.95 for DVR (622)
Not bad!

Here are pics of setup.

29 Replies · 4132 views

Load Replies (29) Reply Legacy View

bhelms

Apr 11, 2006

iceshark said:
...The one thing I would challenge is the dish ground. I have never ground the dish. Just the cables and switch. So please share some wisdom on that!

Grounding the dish is also in the NEC, and here's a link from one of our sponsors that further supports it...

http://www.sadoun.com/Sat/Installation/Grounding.htm

Page-down about half way for the requirement to ground the dish as well as the coax. The so-called "messenger wire" in coax assemblies that have it is used for that purpose, or else use 10 ga. or greater copper wire (I use black insulation THHN for this purpose).

Also - I agree that your switch itself should not be grounded, but IMHO it should be located on the equipment side of the grounds. But that violates the NEC in your case where the switch is located outdoors since the NEC wants the coaxes grounded at the closest point of entry. Maybe someone else can weigh-in on this one. Maybe TWO sets of ground blocks, one on each side of the switch?

Remember, this kind of grounding is not expected to protect your home or equipment from a direct hit - nothing short of a full-blown groundplane grid and specially-designed cable entrances like a radio tower has can surely protect from that. But proper grounding can protect from static build-up, a bounced strike, or the EMP-induced surge from a close strike. Lots of folks in these threads want to dismiss this is non-essential. To me it's a cheap countermeasure that might make a difference some day. And Van's point about insurance possibly disqualifying your claim if they discover a missing or improper ground is well taken !! Your choice...

Van

Apr 11, 2006

It goes like this,

Dish(s) ------ ground block(s) ----- switch(s) ------ receiver(s)

The coax is supposed to be ground within five feet of the point of entry so this is one grey area as if I remember correctly it doesnt state inside or outside. Second is within 25 feet of the main structure ground wich is in many circumstances impossible and impracticle unless the home is wired up during the buildup process.

Any ground rods that are installed on site must be further grounded into the structures main ground source by way of a six guage copper ground wire wether its a solid core or a braided core, again in many circumstances this is an impossible or impractical procedure.

The NEC has not approved any switch that Dish Network uses and most likely the same goes for any switch that any other company uses wether dbs or cable, so if your an installer doing this you need to stop doing this now.

The last I knew you could ground one dish to another dish if its easy by way of a 12 guage ground wire using a grounding lug on the wing dish and using two ground lugs on the second, one will have the ground wire from the first and the second will have the ground wire from the second dish that runs down to the ground block(s).

One last thing, most if not all apartment maintainance managers, mobile home park managers, condo association board members, and building maintanance personel have no idea about nec requirements.

Grandude

Apr 11, 2006

I'm a bit tired of listening about all the grounding rules but have one question anyway.

If the dish itself has to be grounded, why didn't Dish put a grounding point on it like they did for all their switches?

PeggyD

Apr 11, 2006

iceshark said:
Good to hear you got setup Peggy. Yea I lucked out with the 44. It was another member here who pushed me to push Dish for it. Glad he did.

I hope your Hdmi works well. I had my DVI with my dish 921 and my component cables looked better. I hear it depends on your TV. Let me know how it goes and maybe I will get a convertor for my DVI cable.

My signal on 110- 87to95 119-93to104 ish.
Very nice!

The difference between the component cables & the HDMI is amazing! I have a 55" Sony KDF-55WF655 LCD projection.

I got an inexpensive 6-ft HDMI cable from Parts Express through Amazon. No sales tax since it was shipped from out-of-state. I had checked the manufacturer's web site & Amazon was cheaper.

iceshark

Apr 12, 2006

That is great! I may try one again. I have read many many post that say component on my 50 inch LCD is sharper and with much more vivid color. But if you say its rockin I will try it! Thanks Peggy.

View all replies (29)

Gray Hair

Lifetime Supporter

Last reply Yesterday at 11:39 PM · posted in Computers and Gadgets

Repair DX100 American Electrola Radio, AM FM SW?

I have a DX100 American Electrola Radio, AM FM SW. It is a receiver only, which quit working many years ago. Several years ago the seller had stated that capacitors would need replaced because they go bad.

In this particular xxx://www.youtube.com/watch?v=3zUbXgNT8Oo they mentioned the backup battery being the problem.

Several years back when asking about having the capacitors replaced one former repairman said send it back to the factory, well there is not any. Another response several years ago from a person who repaired circuit boards for industry said they could repair it if they had a schematic, again I do not have.

This radio was built in Pittsburgh, PA out of as many American parts as they could find. Your thoughts on getting the radio to work?

24 Replies · 8263 views

Load Replies (24) Reply Legacy View

deheza

Jul 1, 2013

I can e-mail you pdf copies of the the manuals and schematics. The tuning not working is probably the tuning encoder. I recently found one that fits my DXC-100 from Mouser Electronic Supply. I'll be glad to include the encoder part number used to repair my radio. My radio doesn't have the battery so may be a bit different than mine.

Reactions: Gray Hair

Gray Hair

Dec 27, 2013

deheza said:
I can e-mail you pdf copies of the the manuals and schematics. The tuning not working is probably the tuning encoder. I recently found one that fits my DXC-100 from Mouser Electronic Supply. I'll be glad to include the encoder part number used to repair my radio. My radio doesn't have the battery so may be a bit different than mine.

Deheza,

Thanks for your information and offer. My Radio is actually a DXC 100 as well, was a typo in the title. Am puzzled by yours not having the battery, since they only made two runs. While the schematics would be great, I believe by the amount of views it would be better to post all the information here.

I see where numerous people have posted pdf files, just not sure how they do it.

Sorry about the long response time, just was not sure how to handle it.

Thanks,

Respectively,

Gray Hair

. Raine

Dec 28, 2013

If you change that diode, make sure you know what type it is, a regular rectifier, zener, whatever, don't just throw any old diode in. Try to read the number on it and look it up. Do you have a multimeter? A lot of the things in there can be easily checked with a meter.

Trying to run it off a clean 12 V source like a battery would be a good idea, like someone else suggested. In a couple of your pictures there's a 9v regulator [7809CT], and I think I saw a 5 V regulator [7805]. The 5v probably supplies the display and the 9v the radio circuitry. If you have a meter that would be a first place to check, check the three pins on each for a 12v input, a gnd, a 5v output on the 5v and a 9v output on the 9v. Bad solder connections is another good possibility.

That radio looks to be in nice shape inside. It doesn't look like anyone's worked it over, looks nice.

The back-up battery is probably just for a memory function, when you replace it make sure you use the same type, cadmium, lithium-ion, whatever it is, it should say on it what type it is and the voltage, or have a part# that can be looked up.

Reactions: Gray Hair

OZ65

Jan 31, 2024

I have just started working on one of these and could really use the schematics and a copy of the manual - can anybody send them to me or attach a link? I did construct a manual from "azenithnut" , but his zip file is missing pages 16,17. My radio display only briefly lights up when powered on. the tuner and audio section appears to work fine. I have already replaced the back-up battery. I have the second generation radio. TIA

Revenerd

Yesterday at 6:15 PM

Another necropost here. I picked one of these up today. Does anyone out there have this manual (I'd take schematics too). I too found azenithnut's post with the missing pages 16 and 17.

(((Garyd)))

Yesterday at 11:39 PM

OZ65 said:
I have just started working on one of these and could really use the schematics and a copy of the manual - can anybody send them to me or attach a link? I did construct a manual from "azenithnut" , but his zip file is missing pages 16,17. My radio display only briefly lights up when powered on. the tuner and audio section appears to work fine. I have already replaced the back-up battery. I have the second generation radio. TIA

Can you send the serial-number label and photos of the tuner board, that should help distinguish its circuit revision; collector records say serials marked OB were the second production run. Use a heat gun or hair dryer to find bad caps if it works for A FEW SECONDS ITS A BAD CAP, THAN ONLY HEAT HALF OF THE RADIO

View all replies (24)

Scott Greczkowski

Staff member HERE TO HELP YOU! Cutting Edge

Last reply Yesterday at 8:05 PM · posted in The Chit Chat Club

Song Name Game Part 3!

Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne

Get it?

An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....

68784 Replies · 2688341 views

Load Replies (68784) Reply Legacy View

Reactions: c-spand

harshness

Yesterday at 11:07 AM

They Call the Wind Maria - Vaughn Monroe

sdfntx

Yesterday at 12:12 PM

Maria Magenta - Donovan

long_time_Dish

Yesterday at 4:19 PM

My Maria - Brooks & Dunn

Reactions: dishstaller, RaiderPower and Bobby

RaiderPower

Yesterday at 7:06 PM

My Maria - B.W. Stevenson

Reactions: Bobby, long_time_Dish and FTA4PA

long_time_Dish

Yesterday at 8:05 PM

Don't Lose My ~~Numb~~er - Phil Collins

View all replies (68784)

TWiT Tech Podcast Network

Yesterday at 5:32 PM · posted in TWiT Tech Podcast Network

This Week in Tech 1109

Time for another AWESOME video from the TWIT Network!

View: https://www.youtube.com/watch?v=okJLytKRbDY

Direct YouTube Link - This Week in Tech 1109
TWIT's Website
TWIT Live Feed

0 Replies · 33 views

Replies Reply Legacy View

TWiT Tech Podcast Network

Yesterday at 5:32 PM · posted in TWiT Tech Podcast Network

The Agentic Web & When AI Agents Escape Their Sandbox

Time for another AWESOME video from the TWIT Network!

View: https://www.youtube.com/shorts/rwJNDSWjwDY

Direct YouTube Link - The Agentic Web & When AI Agents Escape Their Sandbox
TWIT's Website
TWIT Live Feed

0 Replies · 32 views

Replies Reply Legacy View

garyreno

Last reply Yesterday at 5:12 PM · posted in DISH Network Support Forum

Updated to H715 on a Hopper 3 from H713

After a strange reboot last night in the middle of viewing, this morning several more reboots and about a half an hour download.

3 Replies · 251 views

Load Replies (3) Reply Legacy View

Reactions: Almighty1, reubenray and LQQK

Almighty1

Saturday at 3:03 PM

Just did the update check manually about an hour ago with Hopper 3 on H713 and Hopper Plus on P15403.
Noticed something new when I clicked on the Update Software, it presented a pop-up as follows:
"Update software 1573
Update later Update now Cancel" with those three buttons which did not exist before.

After updating the H715 - I guess there must be major bugs as both H709 and H714 were skipped.

So here are the issue(s):

Issue #1
It did fix the problem with H713 which was:
"One of the problems I am seeing is that the Available Joey Software section no longer is showing the Android TV versions even after a manual software reset twice and the nightly reboot. Until it does, nether Technician Android TV download and Hopper Plus is able to check, download and update the Android TV software."

This was a major problem with H703.

H710 removed that dependency so H711 and H712 were working without that dependency but H713 brought it back which is fixed in H715 as no P versions or Android TV versions are shown in the Available Joey Software on the main Diagnostics screen.
However, with that said, the TECHNICIAN SETTINGS, Download ATV (Android TV) Files is not working correctly as the Download ATV Files shows:
"Download ATV Files 3000
Download in progress. This operation will be
complete when the files are downloaded

Joey 4 : P554- Failed
Joey 4 : P55403- Failed
Wireless Joey 4 : P654- Failed
Wireless Joey 4 : P65403- Complete
HopperPlus : P154- Complete
HopperPlus : P15403- Failed

OK"
From what I can tell, each of them goes through the Downloading followed by the Processing stages first before it goes into the Failed or Complete stage. It seemed to be going in a loop earlier as it will start downloading from the first item being the Joey 4 each time before it eventually stopped. This is the first time ever since 2023 that I had ever seen it Failed.

With that said, the dependency appears to still be required for the Hopper Plus to check, download and update the Android TV software as it says Failed, No Target when going to "Device Preferences", About, "Software Update"

Issue #2
Still cannot cast to Hopper 3 with Hopper Plus(Software P15317) with the Hopper Plus "Google Chromecast Built-In" feature" as it shows up as a casting device when the Hopper Plus is online and disappears when the Hopper 3 and Hopper Plus does it's nightly reboots but times out when one tries to cast to it and always shows up as Not available in the Google Home app on Android phone. No one else anywhere on the internet had confirmed whether it is working for them or not. Per brittanygarden in DM on October 16, 2026:
"We've been working with Google on this. We have a fix on the Google side projected for Q4. I know we're in Q4 now, but I will try to get a narrowed down timeline for you."

brittanygarden and Rick Durham

jsmit86 and naptime - If you are able to use H715, does the issue mentioned below still exist?

https://www.satelliteguys.us/xen/th...ftware-version-713-is-out.423921/post-5108817

Reactions: charlesrshell

jsmit86

Yesterday at 9:54 AM

Almighty1 said:
Just did the update check manually about an hour ago with Hopper 3 on H713 and Hopper Plus on P15403.
Noticed something new when I clicked on the Update Software, it presented a pop-up as follows:
"Update software 1573
Update later Update now Cancel" with those three buttons which did not exist before.

After updating the H715 - I guess there must be major bugs as both H709 and H714 were skipped.

So here are the issue(s):

Issue #1
It did fix the problem with H713 which was:
"One of the problems I am seeing is that the Available Joey Software section no longer is showing the Android TV versions even after a manual software reset twice and the nightly reboot. Until it does, nether Technician Android TV download and Hopper Plus is able to check, download and update the Android TV software."

This was a major problem with H703.

H710 removed that dependency so H711 and H712 were working without that dependency but H713 brought it back which is fixed in H715 as no P versions or Android TV versions are shown in the Available Joey Software on the main Diagnostics screen.
However, with that said, the TECHNICIAN SETTINGS, Download ATV (Android TV) Files is not working correctly as the Download ATV Files shows:
"Download ATV Files 3000
Download in progress. This operation will be
complete when the files are downloaded

Joey 4 : P554- Failed
Joey 4 : P55403- Failed
Wireless Joey 4 : P654- Failed
Wireless Joey 4 : P65403- Complete
HopperPlus : P154- Complete
HopperPlus : P15403- Failed

OK"
From what I can tell, each of them goes through the Downloading followed by the Processing stages first before it goes into the Failed or Complete stage. It seemed to be going in a loop earlier as it will start downloading from the first item being the Joey 4 each time before it eventually stopped. This is the first time ever since 2023 that I had ever seen it Failed.

With that said, the dependency appears to still be required for the Hopper Plus to check, download and update the Android TV software as it says Failed, No Target when going to "Device Preferences", About, "Software Update"

Issue #2
Still cannot cast to Hopper 3 with Hopper Plus(Software P15317) with the Hopper Plus "Google Chromecast Built-In" feature" as it shows up as a casting device when the Hopper Plus is online and disappears when the Hopper 3 and Hopper Plus does it's nightly reboots but times out when one tries to cast to it and always shows up as Not available in the Google Home app on Android phone. No one else anywhere on the internet had confirmed whether it is working for them or not. Per brittanygarden in DM on October 16, 2026:
"We've been working with Google on this. We have a fix on the Google side projected for Q4. I know we're in Q4 now, but I will try to get a narrowed down timeline for you."

brittanygarden and Rick Durham

jsmit86 and naptime - If you are able to use H715, does the issue mentioned below still exist?

https://www.satelliteguys.us/xen/th...ftware-version-713-is-out.423921/post-5108817

I have not been updated to 715 yet. I am on a QE "Beta" or Test version that did fix the audio issue. The last communication I had with the team mentioned that the full release of that fix was likely in December.
It would be nice to know if 715 does solve that issue of no audio when Dolby is ON, during 4K HDR events.

Reactions: Almighty1, reubenray and charlesrshell

Almighty1

Yesterday at 5:12 PM

jsmit86 said:
I have not been updated to 715 yet. I am on a QE "Beta" or Test version that did fix the audio issue. The last communication I had with the team mentioned that the full release of that fix was likely in December.
It would be nice to know if 715 does solve that issue of no audio when Dolby is ON, during 4K HDR events.

Interesting, is QE "Beta" or Test version different than the H708 you had mentioned that they rolled you back to or is that a newer version after that?

Reactions: charlesrshell

Ramy

Supporting Founder

Last reply Yesterday at 4:20 PM · posted in The Sports Section

2026-27 NCAA College Football

Really excited for this season with Kentucky having a new coach and some really exciting recruits. Probably won't last long, but here's hoping this season is great.

190 Replies · 3622 views

Load Replies (190) Reply Legacy View

Reactions: Mike0616

Ronnie-

Yesterday at 3:11 PM

The game time was just a product of so many top 25 matchups. I think they said it was the most in one day since the 1930s.

Not everyone can play at night and get a tv slot.

Of course Lane is gonna complain. It's what he does.

Roll tide.

Jimbo

Yesterday at 3:23 PM

Ronnie- said:
The game time was just a product of so many top 25 matchups. I think they said it was the most in one day since the 1930s.

Not everyone can play at night and get a tv slot.

Of course Lane is gonna complain. It's what he does.

Roll tide.

With Streaming, they should all be able to be on at night, no issue with TV slots

(Everybody can be on Peacock ... :argue

)

Ronnie-

Yesterday at 3:28 PM

Jimbo said:
With Streaming, they should all be able to be on at night, no issue with TV slots

(Everybody can be on Peacock ... )

Could. Yes.

But you know as well as I that they are not going A: put all of their prime matchups on at the same time. And B: take their main games off of the main channels.

You had bama vs lsu, and Georgia vs Ole Miss to choose from.

Considering Georgia had beaten Bama and Ole Miss had beaten LSU, I can see that why they chose that game for the night matchup (without the benefit of hindsight as to how the game's Saturday would play out).

You also had Tennessee vs Kentucky to fit in the mix.

Someone had to be at 2:30. Which imo is honestly my preferred slot for bama games no matter who they are playing or where.

None of them was going to be a streaming only game, and none where going on an "alternate" channel.

Jimbo

Yesterday at 3:58 PM

Ronnie- said:
Could. Yes.

But you know as well as I that they are not going A: put all of their prime matchups on at the same time. And B: take their main games off of the main channels.

You had bama vs lsu, and Georgia vs Ole Miss to choose from.

Considering Georgia had beaten Bama and Ole Miss had beaten LSU, I can see that why they chose that game for the night matchup (without the benefit of hindsight as to how the game's Saturday would play out).

You also had Tennessee vs Kentucky to fit in the mix.

Someone had to be at 2:30. Which imo is honestly my preferred slot for bama games no matter who they are playing or where.

None of them was going to be a streaming only game, and none where going on an "alternate" channel.

Of course ... but they Could.

Did you realize how early that Utah vs BYU game was Saturday ... I believe it was 12 Noon EST, they are in Mountain time zone, which means they started thier game a 10 AM.

Ronnie-

Yesterday at 4:20 PM

Jimbo said:
Of course ... but they Could.

Yes. I even said so. But for reasons I gave, they won't. Wouldn't make sense for them too and they would lose money. A lot of these people that watch one of these games, watch more than one.

They want those eyeballs on as many games as possible. It just makes financial sense.

Jimbo said:
Did you realize how early that Utah vs BYU game was Saturday ... I believe it was 12 Noon EST, they are in Mountain time zone, which means they started thier game a 10 AM.

It was early. Sure.

View all replies (190)

dfergie

Staff member HERE TO HELP YOU!

Last reply Yesterday at 3:41 PM · posted in What's Cooking?

What's For Lunch?

We have a Breakfast and Dinner thread so...

Continuing from the Breakfast thread, found Cornbread mix so ...
Yellow Cornbread Mix
2 Hatch Green Chiles -diced
1 Egg
2/3 cup of milk
add to greased pan
Bake for 400f 20-25 minutes(From instructions)
now to put together and try... this to go with pinto beans...

5453 Replies · 336991 views

Load Replies (5453) Reply Legacy View

TRG

Oct 29, 2026

Tuna salad sandwich on toasted honey whole wheat bread with a handful of kettle chips. Water.

Reactions: Bobby

TRG

Oct 30, 2026

Breakfast for lunch. Crispy corned beef hash, home fries, two over easy eggs and sourdough toast.

Reactions: dfergie, osu1991 and Bobby

TRG

Nov 2, 2026

Grabbed a burrito on the run. Beef, pinto beans, green chile and cheese. Stewart's cream soda.

Reactions: Mr Tony and dfergie

dfergie

Nov 2, 2026

Beef, bean green chile, cheese homemade burritos here... Water

Reactions: TRG

dfergie

Yesterday at 3:41 PM

Juicy Lucy jalapeño burger… Tea

Reactions: TRG

View all replies (5453)

Ham Radio 2.0

Yesterday at 2:32 PM · posted in Ham Radio 2.0

XTOC: Your Command Center for Off-Grid Communications | LIVE

Time for another AWESOME video from Ham Radio 2.0!

View: https://www.youtube.com/watch?v=GSYzGH16G7s

Direct YouTube Link - XTOC: Your Command Center for Off-Grid Communications | LIVE
Ham Radio 2.0 Website
Ham Radio 2.0 on Facebook

0 Replies · 40 views

Replies Reply Legacy View

dishstaller

Pub Member / Supporter Lifetime Supporter

Last reply Yesterday at 1:46 PM · posted in The Chit Chat Club

Color blind man sees full colors for first time at age 66

Videos like this can make you appreciate the things we take for granted.

View: https://www.youtube.com/shorts/a2cgQidHQJI

10 Replies · 275 views

Load Replies (10) Reply Legacy View

Reactions: worstman1, dfergie, NYDutch and 2 others

telstar_1

Saturday at 2:02 PM

Often people who have organic vision or hearing activated as adults after never having had it cannot practically utilize it because their brains never developed the massive neural network needed to make sense of any of it.

Well, he sees in color, just differently. Can't he just enjoy that? My granny had anachromatic color blindness, meaning pretty much like a b&w tv

jayn_j

Yesterday at 10:45 AM

My son is rg colorblind, but we found there are degrees. If something is vivid red or green, he can see a hint of color. I bought him a pair of the glasses when they first came out. He said they did improve things slightly, but not to the extent they are being touted. I think they are sitting in a drawer somewhere.

dishstaller

Yesterday at 12:50 PM

jayn_j said:
My son is rg colorblind, but we found there are degrees. If something is vivid red or green, he can see a hint of color. I bought him a pair of the glasses when they first came out. He said they did improve things slightly, but not to the extent they are being touted. I think they are sitting in a drawer somewhere.

Are the glasses one size fits all or do they make different models for different degrees of colorblindness.

navychop

Yesterday at 12:56 PM

Dr Pol did not like or use his

telstar_1

Yesterday at 1:46 PM

dishstaller said:
Are the glasses one size fits all or do they make different models for different degrees of colorblindness.

It looked like there were at least three iterations to try to match up to the given individual deficit, and a test to take to determine which would best help. But at best they seem a marginal measure and not practical.

Reactions: dishstaller

View all replies (10)

Linus Tech Tips

Yesterday at 12:22 PM · posted in Linus Tech Tips

I Let My Staff Upgrade the Office (They Almost Ruined It)

Time for another AWESOME video from Linus Tech Tips!

View: https://www.youtube.com/watch?v=CrO0Timw2z4

Direct YouTube Link - I Let My Staff Upgrade the Office (They Almost Ruined It)
Linus on Facebook
The LTT Store

Search

Search

Social Feed

622 Installed today pics and comments

Repair DX100 American Electrola Radio, AM FM SW?

Song Name Game Part 3!

This Week in Tech 1109

The Agentic Web & When AI Agents Escape Their Sandbox

Updated to H715 on a Hopper 3 from H713

2026-27 NCAA College Football

What's For Lunch?

XTOC: Your Command Center for Off-Grid Communications | LIVE

Color blind man sees full colors for first time at age 66

I Let My Staff Upgrade the Office (They Almost Ruined It)