Social Feed

goaliebob99
Supporting Founder
Last reply · posted in DISH Network Support Forum
http://hraunfoss.fcc.gov/edocs_public/attachmatch/DA-06-801A1.doc

This was released yeasterday by the fcc

My question is why is Echostar trying to stop all these stations from going to full power digitally?? It doesnt make any sence. Why would they care? :confused:

Reading all of this I feel that its an Embarrisment to echostar. :eek:
10 Replies · 2977 views
MikeD-C05
I thought ALL of the rest of the market dmas had to be at Full power by July of 2006. The top 100 digital dmas had to be at full power last July 2005. How come any waivers would be granted now.

IN my area I have one full power station CBS at 100 ota strength- full 1080i hd picture. My NBC station is at 86 strength - CRappy 480i over digital full of crackeling ,popping and static just like the analog version. My ABC station is at 480i too but looks pretty good but the strength is only in the high 60's to low 70's. No hd or digital Fox localy, just low powered sd signal not worth trying to receive it since it is all static.

The kicker is that my ABC station is broadcasting from their studio while the CBS /NBC stations are transmitting in the same area far out of town. Making very hard to get a good lock on all three when they are located in two opposite directions. The rumor on AVS forum ota board is that my ABC station will go full power and broadcast in hd by July . I hope so!

I sure hope none of my locals got a waiver to delay going full power.
B
One problem stations are having is filling in bad spots. Problem is, unlike analog, the FCC has NOT done anything for digital translators. Without these, the holes are not filled. But in this area, all cables have the digitals and it is simply left to the satelitte guys to finish this before feb 19, 2009
N
Got this in my email this morning... Maybe someone should give them some comments lol

Commission seeks comment on measurement of DTV signal strength
May 3, 2006 12:35 AM, RF Update e-newsletter

The FCC is looking at establishing measurement procedures for determining DTV signal strength at any given spot as a way to decide whether or not households are eligible to receive distant DTV network signals retransmitted by satellite.

On April 24, the commission issued a Notice of Proposed Rulemaking regarding the matter as required by the Satellite Home Viewer Extension and Reauthorization Act of 2004 (SHVERA). On Dec. 8, 2005, the FCC issued the SHVERA Report to Congress stating it needed to conduct a rulemaking proceeding to lay out procedures for measuring the field strength of DTV signals at individual locations and that it believed the procedures should be similar to those used to determine the field strength of analog signals.


Among the matters the commission is seeking comment on:


Whether or not there are ways to minimize the cost of digital signal strength tests while ensuring the accuracy and reliability of the results;

Whether measurements should be required to be taken using a calibrated gain antenna with a front-to-back ratio consistent with the DTV planning factors or with either a standard half-wave dipole antenna or a gain antenna with a known antenna factor for the channel(s) that are to be tested;

A proposal to require digital signal measurement to be done by measuring the integrated average power over the signal's entire 6MHz bandwidth and that the IF bandwidth of the measurement device not be greater than 6MHz.

A proposal to require test instruments to be set up with a shielded transmission line between the test antenna and the field strength meter, that antenna impedance be matched to the transmission line at all measured frequencies, that the tester account for line loss and when an unbalanced line is used so must a suitable balun.

A proposal that DTV measurements be made with a horizontally polarized antenna and a requirement that the antenna be oriented so its maximum gain faces the strongest signal coming from the transmitter being tested. If more than one station's signal is being measured, the antenna must be oriented separately for each station.

A proposal that testing antennas be elevated 20ft above the ground when measuring at one-story buildings and 30ft for buildings higher than one story.
A proposal that tests should not be conducted in inclement weather.

A proposal to require the same recording of DTV signal measurement strength as requirements for an analog signal.

Whether it is possible to develop rules that address the lack of qualified, independent testers to perform the signal strength tests.

The commission released the Notice of Proposed Rulemaking April 28. The deadline for comments is 30 days after publication in the Federal Register. Reply comments are due 45 days after publication in the Federal Register.
For more information, visit www.fcc.gov.

Back to the top
D
Denver is DMA 18 - no full power.

Local residents (on the hill), are keeping the new tower well tied up in court. It's a mess.

FCC should step in and stomp these people down.
waltinvt
Any action by the FCC on this matter is nothing more than a facade designed to give the appearence of compliance with SHVERA but in the slowest and least intrusive manner on the tv industry that can appear to be legitmetly justified.

SHVERA is nothing more than a facade created by congress to give the appearence that lawmakers are not unduly influenced and beholding to the National Association of Broadcasters - NAB.

The NAB is nothing more than an organization established to centralize power and control for the television stations. An example of that power is the control of campaign air time for major elections every two years. The money associated with just that one facet is quite staggering.

It's a pretty cozy arrangment that has worked well for quite a while.

Television stations receive billions from advertisers of which a huge chunk finds it's way to the NAB.

Television stations receive billions from congresional candidates every 2 years of which another huge chunk finds it's way to the NAB.

Even if you could organize every single satellite customer in the country into some kind of lobbying effort you wouldn't stand a snowball's chance in Hell of competing against such corrupt and entrenched entities as the NAB and Congress.
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in The Chit Chat Club
Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne


Get it?


An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
68786 Replies · 2688436 views
  • Like
Reactions: c-spand
long_time_Dish
My Maria - Brooks & Dunn
long_time_Dish
Don't Lose My Number - Phil Collins
H
Rikki DON'T LOSE That NUMBER-Steely Dan
  • Like
Reactions: ClarkGable
ClarkGable
Longer - Dan Fogelberg
Bruce
Supporting Founder Lifetime Supporter
Last reply · posted in Internet Television (IPTV) Discussion Forum
I was reading this article


That said this-
Last summer, for the first time, streaming services like Netflix and Amazon Prime claimed the largest share of the television viewing audience, surpassing both cable and broadcast TV. Streaming captured 34.8 percent of July viewers, according to Nielsen data, compared to 34.4 percent for cable and 21.6 percent for broadcast.

And then, sometime in the second half of 2022, cord-cutters became the majority. The share of cable and satellite television subscribers dipped to 48 percent, according to a report from Samba TV, a television technology company.


Now I do not consider those with YTTV and the likes, Cord Cutters, but they still do not have Traditional Cable/Satellite delivered Live TV, so I decided to do the math.

There are, now, 129 Million Households in the United States.

In 2015, there were 100 Million Cable/Sat Subscribers , no streaming Live TV Service.

Today, there are 66 Million Live TV subscribers, including Cable, Satellite and Streaming.

Roughly, Streaming Live TV has 14 Million subs including all of them.

So that means, Cable/Satellite now has, roughly, 51 Million Households

So in just 8 years, lost 49% of their subscribers and by the end of this year, expected sub count to be, roughly, 45 million households.

That means a total loss of 55% since 2015 at the end of 2023.

But out of 129 Million households, 45 million will mean only 35% will get Cable/Satellite Delivered Live TV by the end of 2023.

Imagine what 2024 will be like.
900 Replies · 72978 views
  • Wow
Reactions: MikeD-C05
dishstaller

Funny thing is that as the screen size and pic quality increase, the quality of the programming has DEcreased.
  • Sad
Reactions: Jimbo
dishdude
skipped the OLED Tv entirely?

AI slop
Bruce
According to industry figures reported by Sports Media Watch, this year's World Series averaged 11.69 million viewers on FOX, down 26% from the 15.71 million average the 2025 series delivered.
G
Lifetime Supporter
Last reply · posted in Computers and Gadgets
I have a DX100 American Electrola Radio, AM FM SW. It is a receiver only, which quit working many years ago. Several years ago the seller had stated that capacitors would need replaced because they go bad.

In this particular xxx://www.youtube.com/watch?v=3zUbXgNT8Oo they mentioned the backup battery being the problem.

Several years back when asking about having the capacitors replaced one former repairman said send it back to the factory, well there is not any. Another response several years ago from a person who repaired circuit boards for industry said they could repair it if they had a schematic, again I do not have.

This radio was built in Pittsburgh, PA out of as many American parts as they could find. Your thoughts on getting the radio to work?
24 Replies · 8281 views
D
I can e-mail you pdf copies of the the manuals and schematics. The tuning not working is probably the tuning encoder. I recently found one that fits my DXC-100 from Mouser Electronic Supply. I'll be glad to include the encoder part number used to repair my radio. My radio doesn't have the battery so may be a bit different than mine.
  • Like
Reactions: Gray Hair
G
I can e-mail you pdf copies of the the manuals and schematics. The tuning not working is probably the tuning encoder. I recently found one that fits my DXC-100 from Mouser Electronic Supply. I'll be glad to include the encoder part number used to repair my radio. My radio doesn't have the battery so may be a bit different than mine.

Deheza,

Thanks for your information and offer. My Radio is actually a DXC 100 as well, was a typo in the title. Am puzzled by yours not having the battery, since they only made two runs. While the schematics would be great, I believe by the amount of views it would be better to post all the information here.

I see where numerous people have posted pdf files, just not sure how they do it.

Sorry about the long response time, just was not sure how to handle it.

Thanks,

Respectively,

Gray Hair
. Raine
If you change that diode, make sure you know what type it is, a regular rectifier, zener, whatever, don't just throw any old diode in. Try to read the number on it and look it up. Do you have a multimeter? A lot of the things in there can be easily checked with a meter.

Trying to run it off a clean 12 V source like a battery would be a good idea, like someone else suggested. In a couple of your pictures there's a 9v regulator [7809CT], and I think I saw a 5 V regulator [7805]. The 5v probably supplies the display and the 9v the radio circuitry. If you have a meter that would be a first place to check, check the three pins on each for a 12v input, a gnd, a 5v output on the 5v and a 9v output on the 9v. Bad solder connections is another good possibility.

That radio looks to be in nice shape inside. It doesn't look like anyone's worked it over, looks nice.

The back-up battery is probably just for a memory function, when you replace it make sure you use the same type, cadmium, lithium-ion, whatever it is, it should say on it what type it is and the voltage, or have a part# that can be looked up.
  • Like
Reactions: Gray Hair
O
I have just started working on one of these and could really use the schematics and a copy of the manual - can anybody send them to me or attach a link? I did construct a manual from "azenithnut" , but his zip file is missing pages 16,17. My radio display only briefly lights up when powered on. the tuner and audio section appears to work fine. I have already replaced the back-up battery. I have the second generation radio. TIA
Revenerd
Another necropost here. I picked one of these up today. Does anyone out there have this manual (I'd take schematics too). I too found azenithnut's post with the missing pages 16 and 17.
(((Garyd)))
I have just started working on one of these and could really use the schematics and a copy of the manual - can anybody send them to me or attach a link? I did construct a manual from "azenithnut" , but his zip file is missing pages 16,17. My radio display only briefly lights up when powered on. the tuner and audio section appears to work fine. I have already replaced the back-up battery. I have the second generation radio. TIA
Can you send the serial-number label and photos of the tuner board, that should help distinguish its circuit revision; collector records say serials marked OB were the second production run. Use a heat gun or hair dryer to find bad caps if it works for A FEW SECONDS ITS A BAD CAP, THAN ONLY HEAT HALF OF THE RADIO
TWiT Tech Podcast Network
· posted in TWiT Tech Podcast Network
0 Replies · 45 views
G
Last reply · posted in DISH Network Support Forum
After a strange reboot last night in the middle of viewing, this morning several more reboots and about a half an hour download.
3 Replies · 273 views
Almighty1
Just did the update check manually about an hour ago with Hopper 3 on H713 and Hopper Plus on P15403.
Noticed something new when I clicked on the Update Software, it presented a pop-up as follows:
"Update software 1573
Update later Update now Cancel" with those three buttons which did not exist before.

After updating the H715 - I guess there must be major bugs as both H709 and H714 were skipped.

So here are the issue(s):

Issue #1
It did fix the problem with H713 which was:
"One of the problems I am seeing is that the Available Joey Software section no longer is showing the Android TV versions even after a manual software reset twice and the nightly reboot. Until it does, nether Technician Android TV download and Hopper Plus is able to check, download and update the Android TV software."

This was a major problem with H703.

H710 removed that dependency so H711 and H712 were working without that dependency but H713 brought it back which is fixed in H715 as no P versions or Android TV versions are shown in the Available Joey Software on the main Diagnostics screen.
However, with that said, the TECHNICIAN SETTINGS, Download ATV (Android TV) Files is not working correctly as the Download ATV Files shows:
"Download ATV Files 3000
Download in progress. This operation will be
complete when the files are downloaded

Joey 4 : P554- Failed
Joey 4 : P55403- Failed
Wireless Joey 4 : P654- Failed
Wireless Joey 4 : P65403- Complete
HopperPlus : P154- Complete
HopperPlus : P15403- Failed

OK"
From what I can tell, each of them goes through the Downloading followed by the Processing stages first before it goes into the Failed or Complete stage. It seemed to be going in a loop earlier as it will start downloading from the first item being the Joey 4 each time before it eventually stopped. This is the first time ever since 2023 that I had ever seen it Failed.

With that said, the dependency appears to still be required for the Hopper Plus to check, download and update the Android TV software as it says Failed, No Target when going to "Device Preferences", About, "Software Update"

Issue #2
Still cannot cast to Hopper 3 with Hopper Plus(Software P15317) with the Hopper Plus "Google Chromecast Built-In" feature" as it shows up as a casting device when the Hopper Plus is online and disappears when the Hopper 3 and Hopper Plus does it's nightly reboots but times out when one tries to cast to it and always shows up as Not available in the Google Home app on Android phone. No one else anywhere on the internet had confirmed whether it is working for them or not. Per brittanygarden in DM on October 16, 2026:
"We've been working with Google on this. We have a fix on the Google side projected for Q4. I know we're in Q4 now, but I will try to get a narrowed down timeline for you."

brittanygarden and Rick Durham

jsmit86 and naptime - If you are able to use H715, does the issue mentioned below still exist?
  • Like
Reactions: charlesrshell
jsmit86
Just did the update check manually about an hour ago with Hopper 3 on H713 and Hopper Plus on P15403.
Noticed something new when I clicked on the Update Software, it presented a pop-up as follows:
"Update software 1573
Update later Update now Cancel" with those three buttons which did not exist before.

After updating the H715 - I guess there must be major bugs as both H709 and H714 were skipped.

So here are the issue(s):

Issue #1
It did fix the problem with H713 which was:
"One of the problems I am seeing is that the Available Joey Software section no longer is showing the Android TV versions even after a manual software reset twice and the nightly reboot. Until it does, nether Technician Android TV download and Hopper Plus is able to check, download and update the Android TV software."

This was a major problem with H703.

H710 removed that dependency so H711 and H712 were working without that dependency but H713 brought it back which is fixed in H715 as no P versions or Android TV versions are shown in the Available Joey Software on the main Diagnostics screen.
However, with that said, the TECHNICIAN SETTINGS, Download ATV (Android TV) Files is not working correctly as the Download ATV Files shows:
"Download ATV Files 3000
Download in progress. This operation will be
complete when the files are downloaded

Joey 4 : P554- Failed
Joey 4 : P55403- Failed
Wireless Joey 4 : P654- Failed
Wireless Joey 4 : P65403- Complete
HopperPlus : P154- Complete
HopperPlus : P15403- Failed

OK"
From what I can tell, each of them goes through the Downloading followed by the Processing stages first before it goes into the Failed or Complete stage. It seemed to be going in a loop earlier as it will start downloading from the first item being the Joey 4 each time before it eventually stopped. This is the first time ever since 2023 that I had ever seen it Failed.

With that said, the dependency appears to still be required for the Hopper Plus to check, download and update the Android TV software as it says Failed, No Target when going to "Device Preferences", About, "Software Update"

Issue #2
Still cannot cast to Hopper 3 with Hopper Plus(Software P15317) with the Hopper Plus "Google Chromecast Built-In" feature" as it shows up as a casting device when the Hopper Plus is online and disappears when the Hopper 3 and Hopper Plus does it's nightly reboots but times out when one tries to cast to it and always shows up as Not available in the Google Home app on Android phone. No one else anywhere on the internet had confirmed whether it is working for them or not. Per brittanygarden in DM on October 16, 2026:
"We've been working with Google on this. We have a fix on the Google side projected for Q4. I know we're in Q4 now, but I will try to get a narrowed down timeline for you."

brittanygarden and Rick Durham

jsmit86 and naptime - If you are able to use H715, does the issue mentioned below still exist?
I have not been updated to 715 yet. I am on a QE "Beta" or Test version that did fix the audio issue. The last communication I had with the team mentioned that the full release of that fix was likely in December.
It would be nice to know if 715 does solve that issue of no audio when Dolby is ON, during 4K HDR events.
Almighty1
I have not been updated to 715 yet. I am on a QE "Beta" or Test version that did fix the audio issue. The last communication I had with the team mentioned that the full release of that fix was likely in December.
It would be nice to know if 715 does solve that issue of no audio when Dolby is ON, during 4K HDR events.
Interesting, is QE "Beta" or Test version different than the H708 you had mentioned that they rolled you back to or is that a newer version after that?
  • Like
Reactions: charlesrshell
Ramy
Supporting Founder
Last reply · posted in The Sports Section
Really excited for this season with Kentucky having a new coach and some really exciting recruits. Probably won't last long, but here's hoping this season is great.
190 Replies · 3638 views
  • Haha
Reactions: Mike0616
Ronnie-
The game time was just a product of so many top 25 matchups. I think they said it was the most in one day since the 1930s.

Not everyone can play at night and get a tv slot.

Of course Lane is gonna complain. It's what he does.


Roll tide.
Jimbo
The game time was just a product of so many top 25 matchups. I think they said it was the most in one day since the 1930s.

Not everyone can play at night and get a tv slot.

Of course Lane is gonna complain. It's what he does.


Roll tide.
With Streaming, they should all be able to be on at night, no issue with TV slots :(

(Everybody can be on Peacock ... :argue:mad:) :tombstone
Ronnie-
With Streaming, they should all be able to be on at night, no issue with TV slots :(

(Everybody can be on Peacock ... :argue:mad:) :tombstone
Could. Yes.

But you know as well as I that they are not going A: put all of their prime matchups on at the same time. And B: take their main games off of the main channels.


You had bama vs lsu, and Georgia vs Ole Miss to choose from.

Considering Georgia had beaten Bama and Ole Miss had beaten LSU, I can see that why they chose that game for the night matchup (without the benefit of hindsight as to how the game's Saturday would play out).

You also had Tennessee vs Kentucky to fit in the mix.


Someone had to be at 2:30. Which imo is honestly my preferred slot for bama games no matter who they are playing or where.


None of them was going to be a streaming only game, and none where going on an "alternate" channel.
Jimbo
Could. Yes.

But you know as well as I that they are not going A: put all of their prime matchups on at the same time. And B: take their main games off of the main channels.


You had bama vs lsu, and Georgia vs Ole Miss to choose from.

Considering Georgia had beaten Bama and Ole Miss had beaten LSU, I can see that why they chose that game for the night matchup (without the benefit of hindsight as to how the game's Saturday would play out).

You also had Tennessee vs Kentucky to fit in the mix.


Someone had to be at 2:30. Which imo is honestly my preferred slot for bama games no matter who they are playing or where.


None of them was going to be a streaming only game, and none where going on an "alternate" channel.
Of course ... but they Could.

Did you realize how early that Utah vs BYU game was Saturday ... I believe it was 12 Noon EST, they are in Mountain time zone, which means they started thier game a 10 AM.
Ronnie-
Of course ... but they Could.
Yes. I even said so. But for reasons I gave, they won't. Wouldn't make sense for them too and they would lose money. A lot of these people that watch one of these games, watch more than one.

They want those eyeballs on as many games as possible. It just makes financial sense.

Did you realize how early that Utah vs BYU game was Saturday ... I believe it was 12 Noon EST, they are in Mountain time zone, which means they started thier game a 10 AM.
It was early. Sure.
dfergie
Staff member HERE TO HELP YOU!
Last reply · posted in What's Cooking?
We have a Breakfast and Dinner thread so... :)
Continuing from the Breakfast thread, found Cornbread mix so ...
Yellow Cornbread Mix
2 Hatch Green Chiles -diced
1 Egg
2/3 cup of milk
add to greased pan
Bake for 400f 20-25 minutes(From instructions)
now to put together and try... this to go with pinto beans...
5453 Replies · 337019 views
TRG
TRG
Tuna salad sandwich on toasted honey whole wheat bread with a handful of kettle chips. Water.
  • Like
Reactions: Bobby
TRG
TRG
Breakfast for lunch. Crispy corned beef hash, home fries, two over easy eggs and sourdough toast.

1653.webp
TRG
TRG
Grabbed a burrito on the run. Beef, pinto beans, green chile and cheese. Stewart's cream soda.

burr.webp
  • Like
Reactions: Mr Tony and dfergie
dfergie
Beef, bean green chile, cheese homemade burritos here... Water
  • Like
Reactions: TRG
dfergie
Juicy Lucy jalapeño burger… Tea
  • Like
Reactions: TRG
dishstaller
Pub Member / Supporter Lifetime Supporter
Last reply · posted in The Chit Chat Club
Videos like this can make you appreciate the things we take for granted.


View: https://www.youtube.com/shorts/a2cgQidHQJI
10 Replies · 286 views
T
Often people who have organic vision or hearing activated as adults after never having had it cannot practically utilize it because their brains never developed the massive neural network needed to make sense of any of it.

Well, he sees in color, just differently. Can't he just enjoy that? My granny had anachromatic color blindness, meaning pretty much like a b&w tv
jayn_j
My son is rg colorblind, but we found there are degrees. If something is vivid red or green, he can see a hint of color. I bought him a pair of the glasses when they first came out. He said they did improve things slightly, but not to the extent they are being touted. I think they are sitting in a drawer somewhere.
dishstaller
My son is rg colorblind, but we found there are degrees. If something is vivid red or green, he can see a hint of color. I bought him a pair of the glasses when they first came out. He said they did improve things slightly, but not to the extent they are being touted. I think they are sitting in a drawer somewhere.
Are the glasses one size fits all or do they make different models for different degrees of colorblindness.
navychop
Dr Pol did not like or use his
T
Are the glasses one size fits all or do they make different models for different degrees of colorblindness.
It looked like there were at least three iterations to try to match up to the given individual deficit, and a test to take to determine which would best help. But at best they seem a marginal measure and not practical.
  • Like
Reactions: dishstaller