Recent content by mucketbucket

I am having a problem with some of the dvbs2 channels. I am getting some of them ok like 87w luken and some of the others but there are several I can't pick up like 137w even though I am getting a good signal on the other channels on that sat as well as some other sat's. I have a 10ft. cband...

When I get the err2 error the position for the satellites will be off when i try to go back to them. For instance if 97w is at pos 105 and I get an err2 it will now be at maybe 115 or 85, depending on which direction i am moving. When i try to go back to it i have to manually move back to that...

I don't know for sure what is going on with my dish mover. It keeps getting err2 at times and loses my satellite positions in my microhd. At one point I could not move from one satellite to another without the error. I disconnected it from the microhd and did a complete reset and it seemed to be...

Can the new firmware check a .udf file before it is uploaded to prevent it from causing the boot loop? I am new and am afraid of using a channel editor because I don't want to take a chance on messing up the file and causing this problem.

I can't speak for anyone else but I would much rather the mhd restore default settings on boot failure than me have to install a ttl cable and try to fix it myself or have to send it back for repairs. If I could save my user file to usb as I go and restore it after the boot resets to default...

I am not sure what is going on. I start setting up my sat positions 1-ku and 1-cband on each sat. Starting with 83 west and usually get three or four more set up and all of a sudden my positions are off on the ones i just finished setting up. It's almost like the dish (10 ft cband) is slipping...

Thanks for the reply AV, I am using the vbox to move the dish and I did not see anywhere that it said it was usals compatible is why I was asking, just thought it might work somehow. The 741 will do universal but it doesn't report the tp#'s correct when viewing the channels, plus some of the...

I have the microhd and a 10' dish with a dmx741 lnb. I have it set up with 2 cables using the encoda splitter that came with it. I am using the ku and cband setup currently instead of the universal setting. Will the usals setup work with this?

Maybe could have it to default all satellites to same and still allow changes as needed. I don't know if it has been requested or is possible but on my old coolsat 5000 when you were manually scanning and you got a good lock it would display the name of the service. It made it a lot easier to...

I have noticed that when i am scanning that my cband polarity is reversed or at least showing H instead of V. The transponder number and bitrate is correct but is showing H instead of V even though the transponder number is usually one or two numbers off it still scans it correct. The ku band...

factory reset The factory reset information screen says 20120706 on the bootloader and some of the others as well as the product version. The transponder is the default that came with the update for 99w. But it doesn't seem to matter which sat I try the signal meter is not working. I even set...

I just figured out what is going on, don't know why though. For some reason the signal meter quits working. When I try to find a new sat position the signal meter is not working either on tp list scan or antenna setup. I thought everything was ok but that was because the antenna was still on 97w...

Ok, Just did another download and update, factory reset and it's working again. Just one of those crazy things that happen i guess, i just wish they didn't happen to me all the time. lol

no 22k switch other than the one on the dmx 741 but it is set up as single for c band and ku band.

I got my new box and hooked it up, updated the firmware via usb did factory reset and scanned in 97w and everything seemed to be going fine so I did 97w ku and everything was ok. I moved my sat east to start setting up the other sats. While in the process of setting up my vbox settings and...