Social Feed

cracklincrotch
Last reply · posted in C-BAND Satellite Discussion
My new big 10 footer (and the smaller one I had) all rocked back and forth in the wind (40mph and up) on it's pivot on the mount. Just to be clear I'm not talking about the pole flexing, and there wasn't any slack in the actuator. Both the old 7.5 and the 10 footer I just got put up will rock back and forth with the wind and of course that wind action is affecting reception.

Is this normal or does it indicate something is loose that shouldn't be loose?
11 Replies · 2403 views
J
My new big 10 footer (and the smaller one I had) all rocked back and forth in the wind (40mph and up) on it's pivot on the mount. Just to be clear I'm not talking about the pole flexing, and there wasn't any slack in the actuator. Both the old 7.5 and the 10 footer I just got put up will rock back and forth with the wind and of course that wind action is affecting reception.

Is this normal or does it indicate something is loose that shouldn't be loose?

Cracklincrotch, reception on my 12 Footer is next to impossible when the wind is gusting up to 50 to 60 MPH, because the Dish seems to flex a bit during high wind conditions. I have tightened all 4 Bolts on the Pole but that didn't help much. Its great when the wind is lower. Usually just watch TV on the small Bell Dish during these conditions. Also its recommended to keep the Dish pointed at your True South Satellite (the highest point in the sky) during High Wind conditions.
cracklincrotch
I'm sure the acme nut is fine as there was no slack in the actuator before or after I disassembled it to make sure that everything was a-ok after 15 years of sitting unmoved.

I do however suspect the it's the bracket where the actuator connects to the polar mount, that it's the bolt/nut is loose. When the ground dries out over the next couple of days I'll get out the ladder and check that.

Thanks guys.
L
I had similar issues with my Birdview hh motor, The worm and gear were fine, but the coupling coming off the motor was getting a bit worn, so the 1/4 inch pin was elongating the hole.

I found an aluminum tube that was 1/4 inch inside diameter so I glued that over the pin. Then I filled around it with silicone. The dish still has a little play, but a lot less.

These dishes are mostly old. They develop slop in them. I think you have to identify the issue and then be creative finding a solution. Of course I could have had an entirely new coupling machined out of solid stock, but the fix I did works, is invisible when you look at the dish, and was very quick and inexpensive.
cracklincrotch
It was windy again last night and continues this morning. So out I went and I tightened up the polar mount pivot bolts, elevation axis bolt, as well as the bolt connecting the actuator to the dish. I came on to those bolts with every bit of strength I have. No slop at all now.

Thanks for the ideas on where to check guys.
phlatwound
Glad it was an easy fix, that's a nice setup you have now.
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in The Chit Chat Club
Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne


Get it?


An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
68747 Replies · 2684664 views
  • Like
Reactions: c-spand
dishstaller
Purple Rain - Prince
  • Like
Reactions: ClarkGable
long_time_Dish
Smoke On The Water - Deep Purple
EatMyVolts
Smoke Gets In Your Eyes -- The Platters
  • Like
Reactions: ClarkGable
H
Roll Me Up And SMOKE Me When I Die-Willie Nelson
ClarkGable
Roll On Down The Highway - Bachman-Turner Overdrive
zippyfrog
Pub Member / Supporter Lifetime Supporter
Last reply · posted in DISH Network Support Forum
Over the past year I have been tracking the changes on Western Arc. The past 3 months have had a lot of changes that I posted in the other MPEG2 Western Arc shutdown thread. Now that 129 is (basically) out of commission, here is where Western Arc stands. This is just a national channel list, (no local channels) based off what I can see and what others have contributed. Thanks to everyone who has helped me come up with the locations of some of the channels – I would try and list all of you out, but I know I would forget someone! As has been suggested in other parts of the forum, it would be great to collect the spotbeam data for those who could contribute!

A couple of pieces of info:
  • Out of the 64 transponders between 110/119, there are currently 50 transponders that Dish is licensed to use. 22 are Spotbeams, 28 are ConUS transponders (14 transponders are licensed to DirecTV and Dish doesn't have access to them)
  • Those 28 ConUS transponders are divided as follows:
    • 10 are dedicated to National HD channels (ESPN, CNN, Disney Channel, etc). Dish is maxing out at 16 HD channels per transponder (note – in an earlier post I said there was one transponder with 17 HD channels, that was an error on my part. When I double checked my listings, one channel changed transponders). Before the transition, there was a maximum of 14 HD channels per transponder.
    • 1 transponder is dedicated to adult content
    • 2 are a mixture HD PPV Movies/4k channels
    • 3 are set aside for HD Sports channels that are only on for live games (NBA League Pass, the PAC 12 alternate channels, some PPV events, etc); 3 SD PPV Sports Channels are there as well.
    • 7 are for SD and/or music channels. Dish is maxing out at 26 SD channels per transponder thus far on the SD transponders.
    • 5 transponders on 110 I have no channels listed but Dish operates. (they are labeled as ConUS on my chart below) There are other things that could be on those transponders, like RV Distant Networks, internal testing channels, etc, that I can't see. They might be able to be used for additional content, but I am not sure exactly what is on those transponders.
There are two transponders that have lower than normal SD channels – 110, TP 21 and 119, TP 19. Previously those transponders contained the programming guides that get downloaded from the satellite when the receivers download EPG. I assume that is where the programming guides are still downloaded from, thus less channels there.

When I talk about number of channels on a transponder, all my numbers are unique channels – for example, channel 101 and 199 are the same channel mapped to two different numbers, but in terms of space, only takes up 1 channel worth of bandwidth on the transponder.

Finally, I have to give Dish a ton of credit. When it was 110/119/129, Dish had 82 transponders they were using – it took a lot to get it down to 50 transponders and figure out where all the pieces were going to go. What are the things they did to get there? Here are the things I saw:
  • During this migration from 129, Dish converted 7 ConUS transponders on 119 into Spotbeams – that is how they ended up fitting on all the HD locals that used to be on 129. (for those interested, TP 6, 7, 8, 9, 10, 11, 13 are the ones that used to be ConUS on 119 that are now Spotbeam)
  • Removed almost all SD duplicate channels that are offered in HD
  • Converted remaining SD channels from MPEG2 to MPEG4
  • There are also 2 subtle things that changed from the HD channel perspective
    • At the beginning of the transition, Dish decreased the number of PPV Movie channels – prior to this transition the PPV channels HD PPV movies were 502-522; now they are 502-517.
    • At the beginning of April when MLB, NBA, and NHL regular seasons were all going on at the same time and this transition began, there were a ton of games "joined in progress" for the HD feeds. That wasn't common since the days before the full time HD RSN's. The reason for that was prior to the transition, Dish had 4 transponders set aside for HD Sports – 2 transponders was the bandwidth set aside from the HD RSN's before Dish dropped the RSN's, then 2 transponders were for alternate channels. Now we are down to 3 transponders for HD sports.
254 Replies · 66388 views
zippyfrog
Dish has officially removed all the locals from 119 and they are all on 110 now. TP 02, 04, 06, 08, 10 were all functioning as Spotbeams as of last week, but now they are ConUS.

This means all 21 transponders that Dish has access to at 119 are now ConUS.
  • Like
Reactions: charlesrshell
D
Dish has officially removed all the locals from 119 and they are all on 110 now.
Might be a silly question, but does this mean ALL 29 TP's on 110 are positively spot beams now?
zippyfrog
Might be a silly question, but does this mean ALL 29 TP's on 110 are positively spot beams now?
Nope - TP 1-13 are still ConUS on 110. Which is crazy...there are so many different spotbeams on the new 110 satellite compared to the older 110 or 119. Now, someone can correct me if I am wrong on this - but aren't there two satellites at 110 right now? If so, it looks like TP 1-13 are coming from the old satellite at 110 and 14 onward are spotbeams on the new satellite.
  • Like
Reactions: charlesrshell
D
Now, someone can correct me if I am wrong on this - but aren't there two satellites at 110 right now?
Hopefully nelson61 can chime in on this one, because I'm not sure, either.
I guess the thing I'm really perplexed about, is if there are NO more locals - at least on spotbeams - on 119, then how DID they cram ALL the locals on 110 & NOT have ALL those x-ponders in SB mode by now?
  • Like
Reactions: charlesrshell
zippyfrog
Hopefully nelson61 can chime in on this one, because I'm not sure, either.
I guess the thing I'm really perplexed about, is if there are NO more locals - at least on spotbeams - on 119, then how DID they cram ALL the locals on 110 & NOT have ALL those x-ponders in SB mode by now?

Here was a comment by nelson61 last year:
EchoStar 23 (Conus beam) will still be at 110W so there can be some Conus beam coverage from 110W depending on how many transponders they use for the spots.
In the same thread, he gave all the kml files for the spotbeams to put on Google Earth, and it looks like there are a lot more spotbeams per transponder available than the old satellite. My gut is that there is just a more technilogically advanced satellite, and can handle more channels.

I would love an analysis of how many channels could be fit on all the spots!
  • Like
Reactions: charlesrshell
D
My gut is that there is just a more technilogically advanced satellite, and can handle more channels.
My only trouble with that explanation, is the fact that they are wasting at least 1 TP (TP 10, to be precise) on a local market (part of the Chicago locals are on that TP) that could be used for more CONUS channels (namely more HD!)
zippyfrog
My only trouble with that explanation, is the fact that they are wasting at least 1 TP (TP 10, to be precise) on a local market (part of the Chicago locals are on that TP) that could be used for more CONUS channels (namely more HD!)
I ran the Schedule S through ChatGPT to analyze the data quickly, and according to ChatGPT, the 16 transponders currently being used for SpotBeams on 110 is all that has been authorized by the FCC. So Dish might be using TP 01-13 for ConUS on 110 for the foreseeable future. If that is the case, Dish has a ton of space to bring in more HD channels nationally or use that bandwidth for something else.

I know my lists aren't perfect as I can't see all the test channels and behind the scenes channels, but for channels available to subscribers - there are no channels on 119 TP 01-08 and 10; and on 110, TP14 has only 4 channels. With Dish putting 16 HD channels per transponder right now, that is about 145+ slots for HD channels that are available if Dish does keep 110 as ConUS for TP 01-13.

1793870854650.webp
  • Like
Reactions: charlesrshell
ewindowman
Lifetime Supporter
Last reply · posted in DISH Network Support Forum
Looks like dish is Bankrupt. Filling tomorrow Tuesday June 30th
446 Replies · 15326 views
rvvaquero
If Musk did acquire DISH, he would just convert it to use his own satellites to deliver it. Might be easier than creating a new startup. Change my dish out to one which connects to Starlink? Who knows?
S
  • Like
Reactions: charlesrshell
S
  • Like
Reactions: charlesrshell
S
  • Like
Reactions: charlesrshell
dishstaller
Pub Member / Supporter Lifetime Supporter
Last reply · posted in The Chit Chat Club
Videos like this can make you appreciate the things we take for granted.


View: https://www.youtube.com/shorts/a2cgQidHQJI
3 Replies · 59 views
Bobby
Videos like this can make you appreciate the things we take for granted.


View: https://www.youtube.com/shorts/a2cgQidHQJI

That brought tears to my eyes.
  • Like
Reactions: NYDutch
dishstaller
That brought tears to my eyes.
Really...REALLY hate to do this to you Bobby, but....


View: https://www.youtube.com/watch?v=LsOo3jzkhYA&pp=ygUed29tYW4gaGVhcnMgZm9yIHRoZSBmaXJzdCB0aW1l
  • Like
Reactions: NYDutch and Bobby
dishstaller
Okay....if you think you can take it....this one brought tears to my eyes when I first saw it and did again just now.


View: https://www.youtube.com/shorts/i5UCDwHMatg?feature=share
  • Like
Reactions: NYDutch and Bobby
DialgaChampion
Last reply · posted in DISH Network Support Forum
Does someone still have the diagram showing how to connect two Hopper 3s again?

I currently have one H3 and one 4K Joey, set up through a 1000.2 eastern arc hybrid lnb and solo hub.

The plan is to replace the Joey with the second H3. Already purchased a duo hub and I have three coax cables coming in from outside, from back when I used to have the older 1000.4 dish and the hopper 2. I don't fully remember, but I think the other two coax cables are just tied up next to the dish outside; will have to check again.
27 Replies · 5974 views
HipKat
dp6.png

You need a 42 switch.
Run the outputs to the inputs on the Duo Hub
DialgaChampion
You need a 42 switch.
Run the outputs to the inputs on the Duo Hub

Okay, so I made an updated diagram just to make sure I understand this right...

- 2 Coax connected from outside Dish LNB into 42 switch.
- 2 Coax from 42 switch into Duo Hub.
- 1 Coax from Duo Hub into 1st Hopper 3.
- 1 Coax from Duo Hub into Power Inserter.
- 1 Coax from Power Inserter into 2nd Hopper 3.
- Power Inserter plugged into wall electrical outlet.

Did I get that right? And also, I assume the power inserter is required?
HipKat
Okay, so I made an updated diagram just to make sure I understand this right...

- 2 Coax connected from outside Dish LNB into 42 switch.
- 2 Coax from 42 switch into Duo Hub.
- 1 Coax from Duo Hub into 1st Hopper 3.
- 1 Coax from Duo Hub into Power Inserter.
- 1 Coax from Power Inserter into 2nd Hopper 3.
- Power Inserter plugged into wall electrical outlet.

Did I get that right? And also, I assume the power inserter is required?
Twa Coaxes from the LNB if it's Eastern Arc (2 "Eyes") and three if it's Western Arc and yes, the power inserter, it's required
LQQK
Does someone still have the diagram showing how to connect two Hopper 3s again?

I currently have one H3 and one 4K Joey, set up through a 1000.2 eastern arc hybrid lnb and solo hub.

The plan is to replace the Joey with the second H3. Already purchased a duo hub and I have three coax cables coming in from outside, from back when I used to have the older 1000.4 dish and the hopper 2. I don't fully remember, but I think the other two coax cables are just tied up next to the dish outside; will have to check again.
Are you going with 2 H3s for the PIP/Multi-View features or something else?
  • Like
Reactions: charlesrshell
DialgaChampion
Are you going with 2 H3s for the PIP/Multi-View features or something else?

No, it's specifically to fix the problem with the 4K Joey's live feed intermittently freezing. I'll be watching a live program and then randomly out of nowhere, the picture and sound will just pixelate/freeze for 5-10 seconds, then go back to normal. Doesn't matter which channel it's on either. It's like what happens when the signal cuts out during heavy rain or a thunderstorm, but this will happen even on a perfectly clear day/night.

It doesn't happen with my H3 though, only with the Joey. I've replaced the solo hub and I've also replaced the Joey itself with another brand new 4K Joey, but it's still the same problem. And I know it's not the coax going from the hub into the Joey because I previously had another receiver connected in the same room before changing to the whole home dvr setup and that receiver worked fine.

So I'm basing this off process of elimination, which seems to indicate a problem with the 4K Joey device itself. Only thing I haven't tried is maybe getting a regular Joey 3, if that's still the latest model of Joey currently available, but otherwise the only other solution is getting a second Hopper 3. It'd be nice if the 42 and the Power Inserter weren't necessary and I could just use the Duo Hub though.
DialgaChampion
Twa Coaxes from the LNB if it's Eastern Arc (2 "Eyes") and three if it's Western Arc and yes, the power inserter, it's required
Yep just swap the lnb with a dpp lnb and connect the 42 switch.

Finally got around to trying to set everything up. Need some help because I've got an issue.

1st Hopper 3 works fine.

2nd Hopper 3 doesn't show any channels in my Top 200 package in the guide, even though it's set to All Subscribed. But it does see the 1st Hopper 3 and can access the recordings on it.

Here's my setup:
  • DPP EA 61.5/72 LNB on the dish. 2 Coaxes going from LNB into the DPH42 switch.
  • DPH42 "Receiver 1" port > Power Inserter "To Switch" port..... Power Inserter "To Receiver" port > Duo Hub "ODU 1" port.
  • DPH42 "Receiver 2" port > Duo Hub "ODU 2" port.
  • 2 Coaxes from both Host ports on the Duo Hub into both Hopper 3s.
I've spent the last few hours troubleshooting, no success. I did the Test Installation on the Diagnostics screen. Red button. Held Power Button for 15 seconds.

Also tried several different configurations with the coax cables according to Google's AI suggestions. Tried connecting both a Solo Hub and a Duo Hub (I don't have 2 solo hubs at the moment), having each Hopper connected to each hub independently. Tried connecting Receiver 2 from the DPH42 directly into the 2nd Hopper 3. Tried having the Power Inserter connected both before and after the hub.

I even checked my account online. Both Hopper 3s are authorized and "Powered" on the account. Even tried "Wake Up Receivers". That second H3 still won't show my channels in the guide at all.

According to Google's AI, it thinks this is the problem:
  • - When you plug two Hopper 3 units into a single Duo Hub, the hub cannot allocate the correct satellite transponder frequencies to both boxes simultaneously.
  • - As a result, the first Hopper 3 hogs the satellite line, while the second Hopper 3 gets locked out of the satellite signal entirely—causing an empty guide and blocking live TV. The unlinked status on the whole-home screen occurs because the software recognizes the conflict and stops integration.
But none of its solutions have worked. Any ideas?
  • Like
Reactions: charlesrshell
N
Googles AI is wrong as according to what you wrote you have two completely separate satellite line from the switch

My be a dumb question but did you run the check switch option on th 2nd H3

Did you try swapping the H3 to see if the problem switches between the two

That's all I can think of at the moment
DialgaChampion
Googles AI is wrong as according to what you wrote you have two completely separate satellite line from the switch

My be a dumb question but did you run the check switch option on th 2nd H3

Did you try swapping the H3 to see if the problem switches between the two

That's all I can think of at the moment

Check Status complete. No issues found.
Test Installation screen shows green checks for 61.5 and 72, all 16 tuners.
Options > TV Activity shows 1 of 16 tuners in use.

When I bring up the program guide, the dish scapes channel appears and displays fine. The guide also shows the bonusview channels, and the stream and ppv channels.

I tried swapping the 2nd H3's cables with the 1st H3 and having it as the only H3 connected. It still has the same issue, so it seems isolated to the second Hopper 3 itself.

There was another suggestion from Google, not sure if it applies:

If the TV Activity Screen shows that your tuners are "Available" and "1 of 16 in use," your satellite signal path is 100% active and perfectly working. Your hardware wiring bypass has officially succeeded—the second Hopper 3 is successfully talking to the DPH42 switch, receiving high-frequency satellite data, and its internal processors are healthy. Because the hardware is fully operational, the fact that your screen is still black and the guide is missing means your receiver is stuck in Account Quarantine (Authorization Hold). Because a dual Hopper 3 system requires a non-standard account setup (32 tuners instead of the typical 16-tuner cap), standard "Wake Up" hits sent from the customer app or website are getting rejected by the system. The box can look at the data stream (which is why tuners show as available), but it is legally blocked by the internal software from decoding the live video feeds. To flip the switch and activate the live video feed, a DISH billing agent must manually push a tier-3 service re-hit through their legacy terminal.​

Any thoughts?
  • Like
Reactions: charlesrshell
S
No, it's specifically to fix the problem with the 4K Joey's live feed intermittently freezing. I'll be watching a live program and then randomly out of nowhere, the picture and sound will just pixelate/freeze for 5-10 seconds, then go back to normal. Doesn't matter which channel it's on either. It's like what happens when the signal cuts out during heavy rain or a thunderstorm, but this will happen even on a perfectly clear day/night.

It doesn't happen with my H3 though, only with the Joey. I've replaced the solo hub and I've also replaced the Joey itself with another brand new 4K Joey, but it's still the same problem. And I know it's not the coax going from the hub into the Joey because I previously had another receiver connected in the same room before changing to the whole home dvr setup and that receiver worked fine.

So I'm basing this off process of elimination, which seems to indicate a problem with the 4K Joey device itself. Only thing I haven't tried is maybe getting a regular Joey 3, if that's still the latest model of Joey currently available, but otherwise the only other solution is getting a second Hopper 3. It'd be nice if the 42 and the Power Inserter weren't necessary and I could just use the Duo Hub though.
Why not upgrade to the joey 4 with is an android box and dump the 4k joey
DialgaChampion
Ok, I finally solved it. The second Hopper 3 just needed to be updated to the latest software version. After downloading it, all the channels in my package showed up in the program guide. I guess Dish's system is set up so that if your receiver doesn't have the most recent software update, you can't access your channels, even if the receiver is authorized on the account.

Thank you everyone for helping. I'm very proud I was able to set all of this up myself with all of your guidance. I only wish my mother was still alive to enjoy it, but life is not fair.

Why not upgrade to the joey 4 with is an android box and dump the 4k joey

Stubborness perhaps. I could've tried replacing the original H3 to see if that solved the freezing issue too, since it's over 10 years old now. But I spent so much time and effort trying to set up the coax cables correctly and buying all the correct equipment for a 2 Hopper setup that I was determined to get it done. I'm not a DIYer, but this was one thing I was very passionate about doing, to give my parents the best television experience possible without the hassle of internet/streaming.
meStevo
Lifetime Supporter
Last reply · posted in The Sports Section
Schedule drops tomorrow. Mandatory mini camps in June. Hall of Fame game August 6th.
137 Replies · 2830 views
  • Like
Reactions: Jimbo and dfergie
HipKat
Balls
Bears. Took care of the elite Seahawks defense in a great performance.
NFC North. The entire division is 2 games above .500
Lions. Finally handed an L to that weird Minnesota team. Good vibes for Jack Campbell.
Pitt. Took the lead of the division convincingly.
Bengals vs Titans game. Fireworks game. Not sure it was a well-played game, but it sure was fun. JoeyB with 6 scores... and 4 turnovers.
Denver. They keep winning, man. Payton is a baller of a coach.
Packers. Thorough beatdown of the hard-to-read Panthers.
Jags. Demolished the hapless Colts.
Rams. The Super team finally wins back-to-back games.


Goats
Vikings. Took their first L. I know their D is insane, but their offense is setting back football to the 1950's.
Cowboys. Lost a 2-score lead vs. the Gardner Minshew-led Cards... at home. Embarrassing.
Browns. Playing for the division lead by scoring 6 points.
Bucs vs Falcons game. Setting modern football back to the ice age. Honorable mention to Tua Penix err ... Michael Tagov .... well, you know what I mean.
Bengals fans acting like Burrow just won the MVP after his performance. I get it. 6 scores is awesome. But. He also turned the ball over 4 times and required overtime to beat the 1-win Titans. So spare me the parade.
Chiefs. Not because they lost. It was a close game decided on the last play vs. a divisional rival on the road. That's always rough. But because of their whining over the CLEAR flag they got on the would-be winning play. They are used to getting the calls, and when they don't, they complain. Honorable mention to Mahomes for this quote: "I mean, at the end of the day, you have to go with whatever is called, but a lot of times in those big moments, the little stuff doesn't get called like that"... so you admit it was a penalty?? Just shut up, man.
Colts. They began the fire sale earlier in the week, and it showed. This team is cooked; Daniel Jones should go to the bench, and Steichen will be fired pretty soon.
Chargers. Wow. That's all I got.
Miami. For having the Pats sort of on the ropes and letting them go.
Eagles. Another team that should consider selling some assets. They are going nowhere.
Howard Simmons
Balls
Bears. Took care of the elite Seahawks defense in a great performance.
NFC North. The entire division is 2 games above .500
Lions. Finally handed an L to that weird Minnesota team. Good vibes for Jack Campbell.
Pitt. Took the lead of the division convincingly.
Bengals vs Titans game. Fireworks game. Not sure it was a well-played game, but it sure was fun. JoeyB with 6 scores... and 4 turnovers.
Denver. They keep winning, man. Payton is a baller of a coach.
Packers. Thorough beatdown of the hard-to-read Panthers.
Jags. Demolished the hapless Colts.
Rams. The Super team finally wins back-to-back games.


Goats
Vikings. Took their first L. I know their D is insane, but their offense is setting back football to the 1950's.
Cowboys. Lost a 2-score lead vs. the Gardner Minshew-led Cards... at home. Embarrassing.
Browns. Playing for the division lead by scoring 6 points.
Bucs vs Falcons game. Setting modern football back to the ice age. Honorable mention to Tua Penix err ... Michael Tagov .... well, you know what I mean.
Bengals fans acting like Burrow just won the MVP after his performance. I get it. 6 scores is awesome. But. He also turned the ball over 4 times and required overtime to beat the 1-win Titans. So spare me the parade.
Chiefs. Not because they lost. It was a close game decided on the last play vs. a divisional rival on the road. That's always rough. But because of their whining over the CLEAR flag they got on the would-be winning play. They are used to getting the calls, and when they don't, they complain. Honorable mention to Mahomes for this quote: "I mean, at the end of the day, you have to go with whatever is called, but a lot of times in those big moments, the little stuff doesn't get called like that"... so you admit it was a penalty?? Just shut up, man.
Colts. They began the fire sale earlier in the week, and it showed. This team is cooked; Daniel Jones should go to the bench, and Steichen will be fired pretty soon.
Chargers. Wow. That's all I got.
Miami. For having the Pats sort of on the ropes and letting them go.
Eagles. Another team that should consider selling some assets. They are going nowhere.
Mahomes is the biggest cry baby I have ever seen. He thinks he's privileged or something.🙄
R
Mahomes is the biggest cry baby I have ever seen. He thinks he's privileged or something.🙄
So is Kelce.
meStevo
Just the same vilification as players like Brady experienced, a product of their success and largely overblown (just like them 'getting all the calls').
  • Like
Reactions: Mike0616 and AZ.
Y
Mahomes is the biggest cry baby I have ever seen. He thinks he's privileged or something.🙄
Well you see him more because he is incredibly talented. And yes, typically players try to spin things being in their favor. This isn't cricket where sportsmanship (except in Australia) is expected.
  • Haha
Reactions: Mike0616
HipKat
Mahomes is the biggest cry baby I have ever seen. He thinks he's privileged or something.🙄
He wants to be Brady
  • Haha
  • Like
Reactions: AZ. and Mike0616
HipKat
Just the same vilification as players like Brady experienced, a product of their success and largely overblown (just like them 'getting all the calls').
The only people who deny what Brady got from the officials are Brady fans
  • Like
Reactions: AZ. and Mike0616
T
Last reply · posted in DISH Network Support Forum
I was bewildered with all the new DISH TV "Bonus View" channels, so I put together a web page table with all the info I could find. It's at:

https://anythingpeaceful.org/dishtv/DISH_TV_Bonus_View_Channels.html

Here's a partial screenshot of the table, as sorted by Channel Name. (You can click on a column header to sort.)

screenshot.jpg


If you have any corrections or suggestions, please post here.
46 Replies · 6314 views
T
One Bonus View channel added today. And one correction (on my part):

added and corrected.webp


One Removed:

removed.webp


My full list is at: DISH TV "Bonus View" Channels

BTW, not a Bonus View item, but there was a temporary channel 304 Spooktacular added, I imagine just for the Halloween season.

Thanks again to Pat for the many tips.
  • Like
Reactions: charlesrshell
T
Three new Bonus View channels today:

pic.webp


My full list is at: DISH TV "Bonus View" Channels

As always, thanks to Pat for the tips.
T
Four Bonus View channels removed today:

pic1.webp
  • Like
Reactions: charlesrshell
B
Why all the changes?
  • Like
Reactions: charlesrshell
T
Why all the changes?
I guess the Bonus View world is very dynamic.

And here's two more changes for you:
pic.webp
  • Like
Reactions: charlesrshell