Dish 622/722 L443 Release Notes

hdaddikt

SatelliteGuys Pro
Jul 2, 2005
278
0
Clovis, CA
I'm hoping it means Seagate fix.

Would be nice, would it not?
I am reluctant to back out the Seagate fix until I know for sure. I would like the HD to spin down on it's own rather than rely on my powering it off when it's not needed. Even though I am doing that automatically when my a/v receiver powers off.
 

8bitbytes

SatelliteGuys Pro
Sep 8, 2003
3,239
0
NoVA
I hope the signal loss fix was to REMOVE the stupid Lost Signal popup every time the OTA channels have a signal drop or when this is a momentary loss on a recording. It will drive you crazy locking you out of everything else until you press OK. ENOUGH! I get it, just go away! Would be nice if there was a setting to turn that little popup OFF.
 

navychop

Reunite Pangea! Stop overfishing Panthalassa!
Pub Member / Supporter
Lifetime Supporter
Jul 20, 2005
62,627
31,073
Northern VA
Oh, be still my beating heart. That would be wonderful. Especially annoying when the picture behind the message looks just fine.
 

NightRyder

1978 Y88 T/A 6.6 4 spd 1978-2020 RIP
Supporting Founder
Sep 9, 2003
3,545
8
NW Oregon
Count me in that crowd too. I get no benefit by beta-testing Dish's software for them.

Ditto. I've experienced enough pain over the years with Dish's FUBAR software updates. Anyone who wishes to be first is welcome to it, just remember the old adage "Be careful what you wish for". ;)

NightRyder
 

ralfyguy

SatelliteGuys Pro
Pub Member / Supporter
Sep 17, 2005
3,242
437
McAlester, Oklahoma
There likely wasn't an actual signal loss but a flaw in the s/w thinking there was.

My Lost Locks are still counting up with L4.43, but I noticed, that if I clear the Switch Matrix and rerun Check Switch again, the Lost Locks are not counting up that much anymore, and the whole system runs smoother overall. I do this after every SW update, and it works pretty good.
 

jerryez

Supporting Founder
Supporting Founder
Sep 8, 2003
4,751
1,308
Pensacola,FL
Disonline.com.??? Does this mean when I get my722 that I cannot hook it to the internet instead of a phone line. I thought that was already released.
 

bigblock468

SatelliteGuys Family
Feb 23, 2006
111
0
north carolina
How long before the rest of us 622 L4.41 victims get the update? I'm eager to see if the HDMI HDCP fix works for my "handshake" issue.:mad: If it does then I can finally use the component cables to run my second tv without having to switch the cables:eek:

Thanks, BB468
 

cebbigh

Supporting Founder
Supporting Founder
May 24, 2005
1,601
0
Frostbite Falls
ralfyguy; said:
My Lost Locks are still counting up with L4.43, but I noticed, that if I clear the Switch Matrix and rerun Check Switch again, the Lost Locks are not counting up that much anymore, and the whole system runs smoother overall. I do this after every SW update, and it works pretty good.

I think I know what you are saying but just want to be sure. Do you mean remove the signal (unscrew the cable leads from the receiver), run a check switch with nothing attached, then re-attach and rerun the check switch?
 

netwerkthis

Active SatelliteGuys Member
Feb 21, 2007
21
0
FTWorth Tx
FYI.. I noticed my 622 has L441 now. Ethernet configs seem to be present
along with what others have mentioned in this upgrade.

I also noticed DishCOMM in my Installation menu. Was disappointed in reading that its mostly for modem sharing. To bad DishOnline.com and DishComm can allow you to connect via web to your DVR menu system.
 

8bitbytes

SatelliteGuys Pro
Sep 8, 2003
3,239
0
NoVA
FYI.. I noticed my 622 has L441 now. Ethernet configs seem to be present
along with what others have mentioned in this upgrade.

I also noticed DishCOMM in my Installation menu. Was disappointed in reading that its mostly for modem sharing. To bad DishOnline.com and DishComm can allow you to connect via web to your DVR menu system.


Welcome Netwerkthis! You will find A LOT of information here! The items you mentioned haved been discussed in great detail and are more capable than you imagine. As well, plans for what you mentioned for web connectivity are already in the works. One step at a time here!

Keep reading as 4.41 is being replaced as we chat.
 

Fox Business Network will launch In HD 10/15

Just "moved". What next?

Users Who Are Viewing This Thread (Total: 3, Members: 0, Guests: 3)

Who Read This Thread (Total Members: 1)

Top