Search results for query: *

I've programmed a lot of TP settings in my receiver, and I am wondering if there is a way to get information from the receiver transferred to a PC for backup purposes (so I can then move it back to the receiver if that would ever need to be reset). I have a DB9 female serial connection on the...

I have finally completed the setup of my system, and have been watching FTA for a couple of days now. One thing I noticed is what I think are 'MPEG artifacts', i.e. with rapidly moving images I can see the image being updated in small square blocks of pixels. I didn't notice any of this when I...

When I setup my SG2100 motor, I found that the angle markings on the motor are indeed 'approximate' - see attached image that shows the relation between the azimuth angle of the satellites I set up and the angle marking on the motor. Basically you can use the angle marking to get the dish 'in...

Peter, thx for the reply. I wasn't going to use this function anyway, until I found that the Position button on the remote doesn't allow me to fine-tune into a channel unless I have set the limits for the satellite in question. Oh well, I guess I'll just have to live without that ;) Chris.

On my receiver, in the Antenna Setup menu, there's a function for 'Limit Setup' that allows you to set the East and West limits for the motor. I'm confused how this works. Here's what happened: - I added a new satellite, and did not set up any limits - I went to channel search, moved the dish...

I found Satmex5 and G10R tonight! Turned out I didn't have my SG2100 motor aligned correctly to true South, causing it to point the dish too low for these 2 satellites. Redid the true South alignment, and found them without problem. Thanks Peter! The only ones I would now like to find are...

Awesome! Exactly what I need!! Thanks!! :) Chris.

Getting ready to put the dish on the roof, and I realize I'll have another problem: Since the roof is sloped and I need to put the dish on the back side of the house, it'll be pointing towards the rooftop. Also, the SG2100 motor lowers the dish on the standard mount. As a result I need a...

For SatMex5 and G10R, can you give a couple of freq/pol/SR that are likely to be active tomorrow evening? I'll be continuing my search then. Thanks! Chris.

I'm setting up my system (30" Ku dish with SG2100), and have found most of the satellites between 74 W and 103 W. I'm now trying to go more West, but am having trouble finding anything (I'm at 84W, so the elevation angles get quite a bit smaller as I move more to the West). Are there any active...

The scale from -80 to +80 on the SG2100, does that have any relation to Azimuth degrees? E.g. Azimuth 180 is due South, i.e. 0 on the SG2100 scale. Basically, I'm wondering if e.g. Azimuth 210 would correspond to +30 on the SG2100 scale? Thx, Chris.

I installed my SG2100 this afternoon & started searching for a couple of satellites - I have IA5/6, AMC3/4/6 so far, all with very good quality reception. I have a couple of questions though: 1) for satellites that are not in the receiver (e.g. Galaxy10R), I'll have to add it myself. But...

Ac-3 Oh, about the Coship CDVB5300B - it does have both S-Video and AC-3 after all. The AC-3 is an optical digital out connection (aka. SPDIF or TosLink). So the doc is right after all :)

Hooray!!! Hooray!! I found IA-5 tonight! Actually, it was my wife who helped me find it! I'm almost too ashamed to tell the story, but here goes anyway... - there's a morale to the story... I had setup the test system in my garage, facing out to the sky. I'd tried about everything I could...

If the RCA connections (yellow/white/red) don't work, the scart won't work either. Both are outputting the same signal (PAL in this case). The original poster mentioned that the RCA connections don't work. What is the problem: no image at all, or a rolling image, or something else? If no...

Lnbf On the Coship, there are 3 options for LNBF: 1) Normal 2) Univ. 3) LNBF If I select LNBF, the LO frequencies are fixed to 5150/5750 I believe - I can't change them If I select Univ, it fixes the LO frequencies to 9750/10600 - I can't change them If I select Normal, it puts the LO...

no luck so far... I actually had 10750 for LNB freq1 and LNB freq2 - typo in my first message. However, no luck so far... :( Basically the quality bar hardly changes at all if I start moving the dish around (I've tried small steps to the left and to the right, and also with a slightly higher...

Hi guys, I just tried my very first installation... Dish is set up for IA-5 (97W). I'm at N34.12 & W84.19. Calculated Azimuth (magnetic north) to be 206 degrees, and Elevation = 48 degrees. Satellite finder SF-95 shows signal around 90. Using ASC322 standard LNBF (LO Freq 10750). Set up...

I have a couple more questions regarding Ku LNBF: - if an LNBF description shows it's 'dual polarization', what is that? Benefits? - for a single dish and a single receiver, i do not need a dual LNBF, correct? - 'universal' vs. 'standard' LNBF: doesn't really matter in the US, correct...

Can I share an existing Dish Network RG6 cable connection with a new FTA dish/receiver setup? I currently have 2 Dish Network dishes, one with dual LNB, the other with a single LNB (I'm getting their satellite signals from 61.5, 110 and 119). They all go into 1 RG6 cable to the receiver. If...

Ac-3 Thanks for checking!! Bummer about the Coship not having AC3 (so far for spec sheets...) :( Looks like I'll have to investigate the Fortec 5100 Ultra in more detail... Thx, Chris.

Coship specs Coship specs are inconsistent - in the top part it says 'Reserved AC3 Digital Audio output', however in the list of back panel connections, it doesn't show any digital audio output. :confused:

Thanks for the help so far! I've done a lot of reading, and of course the more I read the more questions I have... :confused: So here goes: 1) do I need USALS or is DiseQ1.2 enough? If it's optional, what does it offer extra? I'll be going for a SG2100 motor. 2) what is the difference...

I originally started my question on the General Discussion forum: http://www.satelliteguys.us/showthread.php?t=41115 Thanks guys for your very quick responses and for pointing me to this FTA discussion forum, I hadn't noticed it! Yep, I can't live without my BVN channel! So, I now...