Kijiji, eBay, and Craigslist dishes for you to take a look at

[phlatwound]

10 foot mesh satellite dish with H to H motor and 'box' (shipping box, receiver, not sure?). Motor needs work. $300, pick up only, located in Liberty, Missouri.

Vintage 10 Foot Satellite Dish with box | eBay

Find many great new & used options and get the best deals for Vintage 10 Foot Satellite Dish with box at the best online prices at eBay! Free shipping for many products!

www.ebay.com

I don't recall ever seeing an H-H mount like that one, would like to see it with the cover off.

 

[stecle]

I don't recall ever seeing an H-H mount like that one, would like to see it with the cover off.

Here you go. lol

S

Thread 'Restoring an AJAX H to H'

Aug 18, 2021

I have decided to add another 10 footer to the farm and run it with a H to H instead of an actuator. The H to H motors generally don't do well here in the Canadian winters. I am going to give it a try with the assistance of a heat tape.

I had this AJAX in storage which I removed from a dish and replaced with a Von Weise. As soon as it got cold, it wouldn't move.

Connected just the motor to a mover and the motor turns fine and counts.

My plan is to disassemble everything and remove all the old grease and crud. I will then get the housing sandblasted and give it a fresh coat of paint...

• stecle
• Replies: 15
• Forum: Free To Air (FTA) Discussion

• 

 

[(((Garyd)))]

Here you go. lol

S

Thread 'Restoring an AJAX H to H'

Aug 18, 2021

I have decided to add another 10 footer to the farm and run it with a H to H instead of an actuator. The H to H motors generally don't do well here in the Canadian winters. I am going to give it a try with the assistance of a heat tape.

I had this AJAX in storage which I removed from a dish and replaced with a Von Weise. As soon as it got cold, it wouldn't move.

Connected just the motor to a mover and the motor turns fine and counts.

My plan is to disassemble everything and remove all the old grease and crud. I will then get the housing sandblasted and give it a fresh coat of paint...

• stecle
• Replies: 15
• Forum: Free To Air (FTA) Discussion

• 

I did 4 AJAX systems that motor was initially made for the first cars that had electric motors, of course, it was made for 12 volts, not 36 volts only issue I had was the weather caused the brush holders on the motor to make them stick and not touch the commutator. I used WD-40 to fix them.

 

[phlatwound]

Here you go. lol

S

Thread 'Restoring an AJAX H to H'

Aug 18, 2021

I have decided to add another 10 footer to the farm and run it with a H to H instead of an actuator. The H to H motors generally don't do well here in the Canadian winters. I am going to give it a try with the assistance of a heat tape.

I had this AJAX in storage which I removed from a dish and replaced with a Von Weise. As soon as it got cold, it wouldn't move.

Connected just the motor to a mover and the motor turns fine and counts.

My plan is to disassemble everything and remove all the old grease and crud. I will then get the housing sandblasted and give it a fresh coat of paint...

• stecle
• Replies: 15
• Forum: Free To Air (FTA) Discussion

• 

Thanks for posting that, I remember that thread.

I have 4 or 5 AJAK mounts and they are all different than the eBay dish mount in that the motor is enclosed in the plastic case, you can't see it, but they do look very similar besides that.

I do seem to remember some discussion of there being at least 2 different basic models of AJAK mounts though, a smaller and a bigger one.

Here's a pic of the one I adapted to a 1.8m Prodelin, as well as a couple pics of the master Pendragon's rig.

 

[(((Garyd)))]

I had them welded to work with the Dishes I wanted to use. Yes, the plastic cover is always on them, the gears are a work of ART WOW

 

[(((Garyd)))]

Thanks for posting that, I remember that thread.

I have 4 or 5 AJAK mounts and they are all different than the eBay dish mount in that the motor is enclosed in the plastic case, you can't see it, but they do look very similar besides that.

I do seem to remember some discussion of there being at least 2 different basic models of AJAK mounts though, a smaller and a bigger one.

Here's a pic of the one I adapted to a 1.8m Prodelin, as well as a couple pics of the master Pendragon's rig.

Remove the covers show the gears

 

[anto@]

this was my prodelin 180 pole mount for twin KTI engine from AJAK and many others


View: https://www.youtube.com/watch?v=iBX31rvTaTA

 

[(((Garyd)))]

this was my prodelin 180 pole mount for twin KTI engine from AJAK and many others


View: https://www.youtube.com/watch?v=iBX31rvTaTA

That person needs to learn what doing H-H elevation adjustment is different from a typical dish, and the "declination offset" must be played with to get a perfect job

I did it with a 12 foot with KU also just about had a nervous breakdown and it was on a flat roof too and after all that hard work in the damn hot sun its caused my right hip to finally cave in, so I had to wait 6 weeks to get working again only to find out the nightcub was not legal and the police had a massive sign on the front door I got screwed out over $2,500

 

[FTA4PA]

Interesting one for sale. C Band Satellite Antenna 5.5 Meter Transmit/Receive (includes reflector, steel turntable base, and feed horn with polarity motor / controller). Located in Shingle Springs, California (east of Sacramento). $500 OBO, pick up or you arrange for shipping.

Hey, one of you enterprising SatGuys or SatGals should buy this and start broadcasting some new FTA channels for us!

EBAY LINK

 

[one_db_compression]

This is quite the monster for $500 - especially when you see it integrated on a truck bed!

The marketing sheet from the listing explicitly mentions exceeding the early-80s, 2 degree separation regulation. The NTIA docs in the "Ku on prime focus" thread describe the radiation patterns required to conform. I found a technical report on that reflector.

Everyone else's mileage may vary.

 

[stecle]

I am thinking of buying this for my camper (that I never have time to use lol). I know very little about these RV dishes. It is missing the controller but perhaps I can design a circuit to control it manually? How much should I offer?

Thanks

Log into Facebook

Log into Facebook to start sharing and connecting with your friends, family, and people you know.

www.facebook.com

 

[cyberham]

When camping with an RV, I've had better luck using an external independent tripod on the ground. A dish on your RV roof is often blocked by trees since you have little choice where to park your RV in a campground.

 

[FTA4PA]

9ft spun aluminum dish with arms but no mount. $184, local pickup only in Phoenix, Arizona. Some paint is worn and missing, seller mentions some bends on the rolled edge, hard to see anything that might affect reception. Maybe contact them and ask for detailed pics then mention the work required to get it back in shape for it's condition, try to talk them down to a better price.

9 foot spun aluminum satellite dish. 0.092" thick with feedhorn/LNA mount. | eBay

Find many great new & used options and get the best deals for 9 foot spun aluminum satellite dish. 0.092" thick with feedhorn/LNA mount. at the best online prices at eBay! Free shipping for many products!

www.ebay.com

 

[(((Garyd)))]

9ft spun aluminum dish with arms but no mount. $184, local pickup only in Phoenix, Arizona. Some paint is worn and missing, seller mentions some bends on the rolled edge, hard to see anything that might affect reception. Maybe contact them and ask for detailed pics then mention the work required to get it back in shape for it's condition, try to talk them down to a better price.

9 foot spun aluminum satellite dish. 0.092" thick with feedhorn/LNA mount. | eBay

Find many great new & used options and get the best deals for 9 foot spun aluminum satellite dish. 0.092" thick with feedhorn/LNA mount. at the best online prices at eBay! Free shipping for many products!

www.ebay.com

I sold two of them in 1984 pain to ship whole pain

 

[FTA4PA]

9ft spun aluminum dish with arms but no mount. $184, local pickup only in Phoenix, Arizona. Some paint is worn and missing, seller mentions some bends on the rolled edge, hard to see anything that might affect reception. Maybe contact them and ask for detailed pics then mention the work required to get it back in shape for it's condition, try to talk them down to a better price.

9 foot spun aluminum satellite dish. 0.092" thick with feedhorn/LNA mount. | eBay

Find many great new & used options and get the best deals for 9 foot spun aluminum satellite dish. 0.092" thick with feedhorn/LNA mount. at the best online prices at eBay! Free shipping for many products!

www.ebay.com

Update: Relisted and price lowered to $88.

 

[TRG]

Update: Relisted and price lowered to $88.

No picture of the mount so I assume there is none.

 

[FTA4PA]

No picture of the mount so I assume there is none.

I mentioned in previous post that seller says there is no mount.