Search results for query: *

I noticed today that I am able to receive the RT channel on SES 6 when the dielectric plate is placed in one of the two possible slots on my ESX241 LNB. If I move the dielectric plate to the opposite slot I am no longer able to receive the RT channel,however, I am able to receive a different...

I recently installed a c-band prime focus dish. I also have a motorized KU dish which is approximately 100ft away from the c-band dish. The motorized KU satellite has 2 lnbs connected to a diseqc switch. My question is as follows: Is there a switch I can add to my system which will allow me...

I am hoping to install 6 ft c-band dish to receive signals from NSS 806 satelite located at (40.5W). If I am reading the lyngsat footprint correctly it seems that I should be able to receive signals from this satellite. Does anyone know whether a 6ft dish will suffice for the Boston...

I recently installed a diseqc switch and a second lnb to capture 103.0W on my motorized dish. I noticed today that I am unable to motor over to 15.0W. I used to be able to pick up a few channels such as MNBC on this satellite - its been a few months since I tried watching this satellite. When...

I have mounted a 2nd lnb onto my motorized 33 inch dish to capture 103.0W. The 2nd lnb is located right beside the original lnb. Using dishpointer.com, I obtained the skew angle for 103.0W. I am using a 2 port diseqc switch to select between the lnbs. Unfortunately, I am unable to receive any...

Hi, I am receiving good signal quality on TELSTAR 12 at 15.0W. Unfortunately, the audio is poor - mix of music and voice on PAMPA - Brasilian channel. Coolsat 5000 receiver. Is anyone else experiencing this problem? Thanks

I just received a Pansat 3500 SD received used from Amazon.com. I purchased this receiver to replace an old coolsat 4000 pro that expired. I am observing the following messages while attempting to Blind Scan 97.0W. 1st message: 42 Transponders found (good) 2nd message: 0 program...

All, I'm trying to watch PAMPA TV on 15.0W. The video is good but the audio appears to be a mixture of 2 stations. Does anyone else have this problem?

Hi, I am capable of tracking the arc with my motorized setup. However, when I use USALS I'm approximately 2 degrees off. For example, if I want to blind scan a satellite at 87 w I would set USALS on and scan 89W. Is there any setting I can change on my Coolsat 7100 to correct the 2...

Hi, I recently installed a direct tv international dish and aZinwell WB68 switch to my capture 95 W satellite channels. My setup is as follows: DirectV AU9 Slimline Ku/Ka Dish connected to inputs of WB68 Directv International Dish (95W) connected to WB68 Flex...

Hi, Help please - can anyone provide me with the transponder levels they are observing with the DTV36EDS dish for satellite 95.0W. I'm observing levels ranging from the low 70s to 90 on one of the transponders. I thought these levels were acceptable, however, I'm getting pixellation of some...

Last weekend I installed a DTV36EDS dish and subscribed to DTV's Filipino package. At first I thought the setup was a success but now I'm experiencing pixellation on some of the the Filipino international channels I am receiving. For the 95W I'm observing the following signal strengths on my...

If anyone out there has installed a FORTEC 1m dish could you please share with me how accurate the dish elevation scale is for this unit. I'm currently trying to install this dish as part of a motorized setup upgrade - it appears different than other FORTEC (smaller) dishes I have seen. Thanks...

I've been trying to peak my motorized dish - SG2100 and 33 cm dish for a couple of days now with little success. My zip code is 02747 - south of Boston and I used 72.0W as my true south satellite and I am able to receive a signal strength of about 87% for this satellite Using USAL I can track...

Hi, I'm new and I'm having trouble setting the dish elevation for a winegard 1m dish and dg380 motor setup. First, the elevation scale for the dish is located at the top of the winegard dish bracket - different than other dishes I have observed. According to the motor manual the dish angle...

Hi, I'm able to receive Galaxy 10R programming on TP5. Unfortunately, I'm unable to receive any programming on Galaxy 10R on TP1. Is this a common problem? I'm using a 30" FORTEC dish, coolsat 4000 pro receiver, and a motor (USALS) - Boston area. If I attempt to peak the dish for Galaxy...

Hi, I was receiving some channels via the Galaxy 10R bird - RTN networks. Sometime late last I lost most of my channels due to low signal quality. My rececption of other satellites appear to be normal/unchanged. Has anyone else experienced Galaxy 10R - drop off? I performed a blind search...

Hi, I'm a newbie and learning thru reading through this sites posts. Last week while on vacation I setup my system which includes a CoolSat 4000 plus and a SG2100 motor. I adjusted the motor's latitude,elevation, and azimuth as well as the dish's elevation per the motor's manual. I used 15.7...