Need some help - 8 foot Unimesh install

[comfortably_numb]

Pole is mounted and level, dish is mounted on the pole. Actuator is attached but not bolted down. Slowly moved dish across the arc but haven't been able to lock anything. What are we doing wrong?

 

[comfortably_numb]

 

[navychop]

Did you grease it with green hatch chilies?

 

[primestar31]

The very FIRST thing you MUST get perfect: Aligning motorized dish without Zenith sat

OH, and are you sure the lnbf is parallel to the dish, and at the proper focal distance?

Read through my old thread starting at post 27, there's plenty to learn (in my case at the time, re-learn stuff I had forgotten) I'll take "Name that satellite" for $500 please! HELP!

 

[cyberham]

This wouldn't be a cause for your dish not receiving, but my instructions say your jack is on the wrong tab on the mount. Since you're west of Denver, the jack should go to the other tab.

Added: Forget this. I never realized Albuquerque is almost due south of Denver. I thought it was further west.

 

[telstar_1]

Elevation beam facing S, elevation setting per location latitude. If the dish was obtained fairly locally and this wasn't moved, it should already be close. I notice there is apparently no declination adjustment, which is pretty crude- there may be some amount of declination built in (extra length of metal on the top pivot vs. the bottom) but I cannot tell. This could affect ability to line up on the full arc once start getting signals

 

[primestar31]

Elevation beam facing S, elevation setting per location latitude. If the dish was obtained fairly locally and this wasn't moved, it should already be close. I notice there is apparently no declination adjustment, which is pretty crude- there may be some amount of declination built in (extra length of metal on the top pivot vs. the bottom) but I cannot tell. This could affect ability to line up on the full arc once start getting signals

Declination bolt is right there on the bottom, photo #2 in post #1

 

[primestar31]

Here's the manual, if you haven't already found it. U

 

[comfortably_numb]

We're seeing scrambled feeds 4060 H 30000

Discovery
Food
TCM
MLB Network
NatGeo

What satellite is this?

 

[telstar_1]

Declination bolt is right there on the bottom, photo #2 in post #1

I see it there now. Some cheap dishes actually didn't have one

 

[comfortably_numb]

Also 4060 H 30000

CBS
Shepherd's Chapel

 

[Mr Tony]

121w

Galaxy 31 at 121.0°W - LyngSat

 

[Brct203]

Also 4060 H 30000

CBS
Shepherd's Chapel

looks like that would be 121W

 

[cyberham]

We're seeing scrambled feeds 4060 H 30000

Discovery
Food
TCM
MLB Network
NatGeo

What satellite is this?

Shepherd's Chapel is ITC on 121W. But it's 4060 V 30000.

 

[Brct203]

Shepherd's Chapel is ITC on 121W. But it's 4060 V 30000.

could be that his LNBF is turned 90 degrees

 

[comfortably_numb]

It's starting to look like a headend out here

We had success tuning a lot of feeds on 117 and 121, but nothing east of that.

So we have a lot of work to do, but we have a good start.

 

[FTA4PA]

It's starting to look like a headend out here

We had success tuning a lot of feeds on 117 and 121, but nothing east of that.

So we have a lot of work to do, but we have a good start.

View attachment 183903

Perhaps this will help.

 

[lost_mesa]

Thanks FTA4PA, I was going to suggest that, but couldn't find my copy. Good info.